Search Results (7)

Angiography is a very informative method for physicians such as cardiologists, neurologists and neuroscientists. The current modalities experience some shortages, e.g., ultrasound is very operator dependent. The computerized tomography (CT) and magnetic resonance (MR) angiography are very expensive and near infrared spectroscopy cannot capture the deep arteries. Microwave technology has the potential to address some of these issues while compromising between operator dependency, cost, speed, penetration depth and resolution. This paper studies the feasibility of microwave signals for monitoring of arteries. To this aim, a homogenous phantom mimicking body tissue is built. Four elastic tubes simulate arteries and a mechanical system creates pulsations in these arteries. A multiple input multiple output (MIMO) array of ultra-wideband (UWB) transmitters and receivers illuminates the phantom and captures the reflected signals over the desired observation time period. Since we are only interested in the imaging of dynamic parts, i.e., arteries, the static clutters can be suppressed easily by background subtraction method. To obtain a fast image of arteries, which are pulsating with the heartbeat rate, we calculate the Fourier transform of each channel of the MIMO system over the observation time and apply delay and sum (DAS) beamforming method on the heartbeat rate aligned spectral component. The results show that the lateral and longitudinal images and motion mode (M-mode) time series of different points of phantom have the potential to be used for diagnosis. Full article

The proposed design approach improves the circularly polarized Fabry-Perot cavity antenna (CP-FPCA) by increasing gain and sidelobe suppression (SLS) while reducing the axial ratio (AR) and cross-polarization levels. Conventional CP-FPC antennas have a high AR due to the lack of independent control over circular polarization conditions. The solution proposes a double-layered circularly polarized partially reflecting surface (CP-PRS) that independently controls the circular polarization conditions at the design frequency f₀ (10 GHz) for equal magnitudes and at a ±90° phase difference between orthogonal components of the transmitted waves. The PRS and artificial magnetic conductor (AMC) unit cells are employed to satisfy Trentini’s beamforming condition, leading to increased gain and SLS and lowered AR and cross-polarization levels. Consequently, the proposed CP-FPCA provides a 15.4 dBi high gain with 25.3% aperture efficiency and more than 23.5 dB high SLS in each plane. Moreover, it achieves an AR lowered by 0.12 dB and a cross-polarization level below −42 dB. A strong correlation between the simulations and experiments proves the practicality of our proposal. Full article

Usually, towed hydrophone arrays are instrumented with a set of compasses. Data from these sensors are utilized while beamforming the acoustic signal for target bearing estimation. However, elements of the hydrophone array mounted in the neighborhood of a compass can affect the Earth’s magnetic field detection. The effects depend upon the materials and magnetic environment present in the vicinity of the platform hosting the compass. If the disturbances are constant in time, they can be compensated for by means of a magnetic calibration procedure. This process is commonly known as soft and hard iron compensation. In this paper, a solution is presented for carrying out the magnetic calibration of a COTS (Commercial Off the Shelf) digital compass without sensor motion. This approach is particularly suited in applications where a physical rotation of the platform that hosts the sensor is unfeasible. In our case, the platform consists in an assembled and operational towed hydrophone array. A standard calibration process relies on physical rotation of the platform and thus on the use of the geomagnetic field as a reference during the compensation. As a variation on this approach, we generate an artificial reference magnetic field to simulate the impractical physical rotation. We obtain this by using a tri-axial Helmholtz coil, which enables programmability of the reference magnetic field and assures the required field uniformity. In our work, the simulated geomagnetic field is characterized in terms of its uncertainty. The analysis indicates that our method and experimental set-up represent a suitably accurate approach for the soft and hard iron compensation of the compasses equipped in the hydrophone array under test. Full article

A new beam scanning method of a Fabry–Perot cavity (FPC) antenna is proposed. To obtain high gain in a target direction with a reduced sidelobe level (SLL), we devised a tapered partially reflective surface (PRS) as a superstrate. Moreover, to attain various beam scanning directions, a phase-controllable artificial magnetic conductor (AMC) ground plane with a broad reflection phase range and high reflection magnitudes was introduced. In the proposed method, a new formula to satisfy an FP resonance condition in a cavity for a scanned beam is also suggested. According to the formula, the FPC antenna can precisely scan the main beam in designed target directions with well-maintained high gain, which has been hardly achievable. In addition, our method demonstrates the potential of electrical beam-scanning antennas by employing active RF chips on the AMC cells. To validate the method, we fabricated a prototype FPC antenna for a scanned beam at θ = 30°. Furthermore, we conducted an additional simulation for a different beam scanning angle as well. Good agreement between the expected and experimental results verifies our design approach. Full article

Magnetic beamforming techniques can enhance the power transfer efficiency using focused magnetic fields by the multiple transmitters to the receivers. However, the intra-couplings that cause power leakage and phase distortion among the arrayed coils inevitably occur due to the deployment of coils having strong couplings between each other. Here, we analyze the adverse influences of intra-couplings and present the advantages of magnetically independent transmitters for multiple-inputs and single-output (MISO) WPT. The independent coil array can achieve focused magnetic fields by simply adjusting the amplitude of the transmitter voltage source without phase adjustment. The system also can eliminate the reactive power with the independent coil array to efficiently use the supplying power from the source. The analytical studies are verified by numerical and circuit simulation and experiments. Our analysis can be generalized to the MISO-WPT with an arbitrary number of transmitters. It can provide insight into designing and implementing the MISO-WPT applying magnetic beamforming. Full article

Since the sound velocity for medical ultrasound imaging is usually set at 1540 m/s, the ultrasound imaging of a patient with a thick layer of subcutaneous fat is degraded due to variations in the sound velocity. This study proposes a method of compensating for image degradation to correct beamforming. This method uses the sound velocity distribution measured in simultaneous ultrasound (US) and magnetic resonance (MR) imaging. Experiments involving simultaneous imaging of an abdominal phantom and a human neck were conducted to evaluate the feasibility of the proposed method using ultrasound imaging equipment and a 1.5 T MRI scanner. MR-visible fiducial markers were attached to an ultrasound probe that was developed for use in an MRI gantry. The sound velocity distribution was calculated based on the MRI cross section, which was estimated as a corresponding cross section of US imaging using the location of fiducial markers in MRI coordinates. The results of the abdominal phantom and neck imaging indicated that the estimated values of sound velocity distribution allowed beamform correction that yielded compensated images. The feasibility of the proposed method was then evaluated in terms of quantitative improvements in the spatial resolution and signal-to-noise ratio. Full article

In a millimeter wave (mmWave) communication system with transmit/receive (Tx/Rx) beamforming antennas, small variation in device behavior or an environmental change can destroy beam alignment, resulting in power loss in the received signal. In this situation, the beam-tracking technique purely based on the received signal is not effective because both behavioral changes (rotation, displacement) and environmental changes (blockage) result in power loss in the received signal. In this paper, a motion sensor based on microelectromechanical systems (MEMS) as well as an electrical signal is used for beam tracking to identify the cause of beam error, and an efficient beam-tracking technique is proposed. The motion sensors such as accelerometers, gyroscopes, and geo-magnetic sensor are composed of an attitude heading reference system (AHRS) and a zero-velocity detector (ZVD). The AHRS estimates the rotation angle and the ZVD detects whether the device moves. The proposed technique tracks a beam by handling the specific situation depending on the cause of beam error, minimizing the tracking overhead. The performance of the proposed beam-tracking technique is evaluated by simulations in three typical scenarios. Full article