Search Results (21)

Pre-lithiation using Li–Si alloy-type additives is a promising technical approach to address the drawbacks of Si-based anodes, such as a low initial Coulombic efficiency (ICE) and inevitable capacity decay during cycling. However, its commercial application is limited by the air sensitivity of the highly reactive Li–Si alloys, which demands improved environmental stability. In this work, a protective membrane is constructed on Li₁₃Si₄ alloys using low-surface-energy paraffin and highly conductive carbon nanotubes through liquid-phase deposition, exhibiting enhanced hydrophobicity and improved Li⁺/e⁻ conductivity. The Li₁₃Si₄@Paraffin/carbon nanotubes (Li₁₃Si₄@P-CNTs) composite achieves a high pre-lithiation capacity of 970 mAh g⁻¹ and superb environmental stability, retaining 92.2% capacity after exposure to ambient air with 45% relative humidity. DFT calculations and in situ XRD measurements reveal that the paraffin-dominated coating membrane, featuring weak dipole–dipole interactions with water molecules, effectively reduces the moisture-induced oxidation kinetics of Li₁₃Si₄@P-CNTs in air. Electrochemical kinetic analysis and XPS depth profiling reveal the enhancement in charge transfer dynamics and surface Li⁺ transport kinetics (SEI rich in inorganic lithium salts) in P-SiO@C pre-lithiated by Li₁₃Si₄@P-CNTs pre-lithiation additives. Benefitting from pre-lithiation via Li₁₃Si₄@P-CNTs, the pre-lithiated SiO@C(P-SiO@C) delivers high ICE (103.7%), stable cycling performance (981 mAh g⁻¹ at 200 cycles) and superior rate performance (474.5 mAh g⁻¹ at 3C) in a half-cell system. The LFP||P-Gr pouch-type full cell exhibits a capacity retention of 83.2% (2500 cycles) and an energy density of 381 Wh kg⁻¹ after 2500 cycles. The Li₁₃Si₄@P-CNTs additives provide valuable design concepts for the development of pre-lithiation materials. Full article

Background/Objectives: Hydrogen sulfide (H₂S) is a vasorelaxant gas and exerts anti-oxidative, anti-inflammatory, and cytoprotective effects. H₂S has been implicated in regulating placental vaso-activity and angiogenesis. It is believed that abnormal trophoblast production of vasodilators and angiogenic factors contributes to pre-eclampsia development. However, little is known about whether aberrant H₂S production is present in placental trophoblasts from pre-eclamptic pregnancies. Methods: Trophoblasts were isolated from normal and pre-eclamptic placentas. After incubation, cell production of H₂S in the culture medium and the cellular levels of H₂S were analyzed by reversed phase high-performance liquid chromatography (RP-HPLC). Expression levels of the three key H₂S converting enzymes, cystathionine-β-synthase (CBS), cystathionine-γ-lyase (CSE), and 3-mercaptopyruvate sulfurtransferase (3-MST), were determined by immunohistochemistry. The protein expression of CBS and CSE was assessed by Western blot analysis. Results: (1) Trophoblast production and cellular levels of H₂S were significantly reduced in cells from pre-eclamptic vs. normal placentas; (2) free H₂S production was increased in a time-dependent manner in cultured trophoblasts from normal, but not from pre-eclamptic, placentas; and (3) strong CBS and CSE expression was seen in trophoblasts from normal, as opposed to pre-eclamptic, placentas. Reduced CBS and CSE expression in trophoblasts from pre-eclamptic vs. normal placentas were confirmed by Western blot analysis; and (4) 3-MST expression was undetachable in both normal and pre-eclamptic placentas, but 3-MST expression was strongly expressed in the first and second trimester placentas. Conclusions: These data provide plausible evidence that downregulation of CBS and CSE, but not 3-MST, expression may be responsible for reduced free H₂S production and decreased cellular H₂S levels in pre-eclamptic placentas. Our data provide further evidence that expression of 3-MST in placental trophoblasts is likely gestational age (developmental)-dependent. Full article

Due to their antibacterial and antifungal properties, parabens are commonly used as biocides and preservatives in food, cosmetics, and pharmaceuticals. Parabens have been reported to exist in various water matrices at low concentrations, which renders the need for sample preparation before their quantification using analytical techniques. Thus, sample preparation methods such as solid-phase extraction (SPE), rotating-disk sorptive extraction (RDSE), and vortex-assisted dispersive liquid–liquid extraction (VA-DLLE) that are commonly used for parabens extraction and preconcentration have been discussed. As a result of sample preparation methods, analytical techniques now detect parabens at trace levels ranging from µg/L to ng/L. These compounds have been detected in water, air, soil, and human tissues. While the full impact of parabens on human health and ecosystems is still being debated in the scientific community, it is widely recognized that parabens can act as endocrine disruptors. Furthermore, some studies have suggested that parabens may have carcinogenic effects. The presence of parabens in the environment is primarily due to wastewater discharges, which result in widespread contamination and their concentrations increased during the COVID-19 pandemic waves. Neglecting the presence of parabens in water exposes humans to these compounds through contaminated food and drinking water. Although there are reviews that focus on the occurrence, fate, and behavior of parabens in the environment, they frequently overlook critical aspects such as removal methods, policy development, and regulatory frameworks. Addressing this gap, the effective treatment of parabens in water relies on combined approaches that address both cost and operational challenges. Membrane filtration methods, such as nanofiltration (NF) and reverse osmosis (RO), demonstrate high efficacy but are hindered by maintenance and energy costs due to extensive fouling. Innovations in anti-fouling and energy efficiency, coupled with pre-treatment methods like adsorption, help mitigate these costs and enhance scalability. Furthermore, combining adsorption with advanced oxidation processes (AOPs) or biological treatments significantly improves economic and energy efficiency. Integrating systems like O₃/UV with activated carbon, along with byproduct recovery strategies, further advances circular economy goals by minimizing waste and resource use. This review provides a thorough overview of paraben monitoring in wastewater, current treatment techniques, and the regulatory policies that govern their presence. Furthermore, it provides perspectives that are critical for future scientific investigations and shaping policies aimed at mitigating the risks of parabens in drinking water. Full article

A system combining gas-phase oxidation and liquid-phase collision absorption for removing NO from marine diesel engine exhaust was proposed. This method was the first to utilize different physical states of the same mixed solution to achieve both pre-oxidation and impingement reduction absorption of exhaust gases. During the pre-oxidation stage, a mixture of (NH₄)₂S₂O₈ and urea solution was atomized into a spray using an ultrasonic nebulizer to increase the contact area between the oxidant and the exhaust gas, thereby efficiently pre-oxidizing the exhaust gas in the gas phase. In the liquid-phase absorption stage, the (NH₄)₂S₂O₈ and urea solution was used in an impingement absorption process, which not only enhanced gas–liquid mass transfer efficiency but also effectively inhibited the formation of nitrates. Experimental results showed that, without increasing the amount of absorbent used, the maximum NO removal efficiency of this method reached 97% (temperature, 343 K; (NH₄)₂S₂O₈ concentration, 0.1 mol/L; urea concentration, 1.5 mol/L; NO concentration, 1000 ppm; pH, 7; impinging stream velocity, 15 m/s), compared to 72% using the conventional liquid-phase oxidation absorption method. Additionally, this method required only the addition of a nebulizer and two opposing nozzles to the existing desulfurization tower to achieve simultaneous removal of sulfur and nitrogen oxides from the exhaust gas, with low retrofitting costs making it favorable for practical engineering applications. Full article

Low-temperature treatments preceding alcoholic fermentation are becoming increasingly popular and have been used in winemaking as a tool to improve wine colour, aroma, and quality. Additionally, the pre-fermentative treatment of grapes with cryogenic agents protects the grape juice (must) from oxidation by reducing the diffusion of atmospheric oxygen into the liquid phase during the winemaking process. Resultant wines were reported to have enhanced varietal aromas, increased complexity, and higher thiol levels. Indications are that increased contact time between skin and juice improves the extraction of the compounds and/or precursors. Recently, there has been considerable interest in the production of wines with enhanced varietal aromas and improved quality by applying innovative winemaking technologies. This review aims to provide an overview of the aroma and organoleptic quality of Sauvignon blanc and Chenin blanc wines produced from grapes that were subjected to pre-fermentative cryogenic treatments including the impact aroma compounds, i.e., volatile thiols and methoxypyrazines. Full article

Electrochemical studies of the drug and micellar aggregates of surfactants have gained interest in recent years. The aggregation of micelles aims to mimic the structures of biological membranes. It also helps to regulate the pharmacokinetic properties of medicines as they offer a path for formulations with controlled release abilities. Propranolol (PPL) is a beta blocker drug which is used as a medication in treatments for hypertension, cardiac arrhythmias, and atrial fibrillation, and it is also used to prevent migraines. The electro oxidation of Propranolol was observed using a glassy carbon electrode in cationic surfactants and ionic liquid surfactants with the same chain length using cyclic voltammetry. A well-defined single irreversible peak was found in the potential range of 0.6 to 1.6 V at room temperature. In this paper, Propranolol, in the absence and presence of both the surfactants, is discussed in terms of the pre- and postmicellar phases. The scan rate and effects of both concentrations were evaluated in the presence and absence of surfactants in biphasic surfactant conditions. Diffusion-controlled and irreversible processes involving an adsorption effect were observed in both the surfactants. The interactions of PPL in the presence of different cationic micelles provide an effective approach for estimating the stability of radicals in biological mimetic systems. Full article

Activated carbon fibers (ACFs) derived from various polymeric fibers with the characteristics of a high specific surface area, developed pore structure, and good flexibility are promising for the new generation of chemical protection clothing. In this paper, a polyacrylonitrile-based ACF felt was prepared via the process of liquid phase pre-oxidation, along with a one-step carbonization and chemical activation method. The obtained ACF felt exhibited a large specific surface area of 2219.48 m²/g and pore volume of 1.168 cm³/g, as well as abundant polar groups on the surface. Owing to the developed pore structure and elaborated surface chemical property, the ACF felt possessed an intriguing adsorption performance for a chemical warfare agent simulant dipropyl sulfide (DPS), with the highest adsorption capacity being 202.38 mg/g. The effects of the initial concentration of DPS and temperature on the adsorption performance of ACF felt were investigated. Meanwhile, a plausible adsorption mechanism was proposed based on the kinetic analysis and fitting of different adsorption isotherm models. The results demonstrated that the adsorption process of DPS onto ACF felt could be well fitted with a pseudo-second-order equation, indicating a synergistic effect of chemical adsorption and physical adsorption. We anticipate that this work could be helpful to the design and development of advanced ACF felts for the application of breathable chemical protection clothing. Full article

A reliable, rapid, and low-cost procedure for determining very low concentrations of hexavalent chromium (Cr) in water is discussed. The procedure is based in the classical reaction of Cr⁶⁺ with diphenylcarbazide. Once this reaction has taken place, sodium dodecylsulfate is added to obtain an ion-pair, and Triton X-114 is incorporated. Next, the heating of the mixture allows two phases that can be separated by centrifugation to be obtained in a cloud point microextraction (CPE) process. The coacervate contains all the Cr⁶⁺ originally present in the water sample, so that the measurement by molecular absorption spectrophotometry allows the concentration of the metal to be calculated. No harmful organic solvents are required. The discrimination of hexavalent and trivalent forms is achieved by including an oxidation stage with Ce⁴⁺. To take full advantage of the pre-concentration effect inherent to the coacervation process, as well as to minimize reagent consumption and waste generation, a portable mini-spectrophotometer which is compatible with microvolumes of liquid samples is used. The preconcentration factor is 415 and a chromium concentration as low as 0.02 µg L⁻¹ can be detected. The procedure shows a good reproducibility (relative standard deviation close to 3%). Full article

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium lanthanum zirconium oxide (LLZO) is considered a promising solid electrolyte due to its safe operating potential window (0–5 V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Ta-doped LLZO (Li₇La₃Zr_1.6Ta_0.4O₁₂, Ta-LLZO) were synthesized for bulk production of a dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO, with carefully controlled process parameters such as heating atmosphere, temperature, and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered Ta-LLZO disc, and refined data were used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of the Ta-LLZO disc were 10⁻⁴ S cm⁻¹ and 10⁻¹⁰ S cm⁻¹, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties. Full article

Given the rising upscaling trend in lithium-ion battery (LiB) production, there is a growing emphasis on the environmental and economic impacts alongside the high energy density demands. The cost and environmental impact of battery production primarily arise from the critical elements Ni, Co, and F. This drives the exploration of Ni-free and Co-free cathode alternatives such as LiMn₂O₄ (LMO) and LiFePO₄ (LFP). However, the absence of Ni and Co results in reduced capacity and insufficient cyclic stability, particularly in the case of LMO due to Mn dissolution. To compensate for both low cathode capacitance and low cycle stability, we propose the GREENcell, a lithium cell combining a F-free polyisobutene (PIB) binder-based LMO cathode with a stabilized in -situ LiAL alloy anode. A LiAl alloy anode with the chemical composition of LiAl already shows a theoretical capacity of 993 Ah·kg⁻¹. Therefore, it promises extraordinarily higher energy densities compared to a commercial graphite anode with a capacity of 372 Ah·kg⁻¹. Following an iterative development process, different optimization strategies, especially those targeting the stability of the Al-based anode, were evaluated. During Al foil selection, foil purity and thickness could be identified as two of the dominant influencing parameters. A pressed-in stainless steel mesh provides both mechanical stability to the anode and facilitates alloy formation by breaking up the Al oxide layer beforehand. Additionally, a binder-stabilized Al oxide or silicate layer is pre-coated on the Al surface, posing as a SEI-precursor and ensuring a uniform liquid electrolyte distribution at the phase boundary. Employing a commercially available Si-containing Al alloy mitigated the mechanical degradation of the anode, yielding a favorable impact on long-term stability. The applicability of the novel optimized GREENcell is demonstrated using laboratory coin cells with LMO and LFP as the cathode. As a result, the functionality of the GREENcell was demonstrated for the first time, and thanks to the anode stabilization strategies, a capacity retention of >70% after 200 was achieved, representing an increase of 32.6% compared to the initial Al foil. Full article

This study investigated the evolution of density, grain size, and pore characteristics during the sintering of metal injection molding (MIM) 420, 420 + 0.3C and pre-alloyed 420Nb stainless steel powders. The results show that C promotes the reduction of oxides on the surface of stainless steel, thereby accelerating sintering at 1330 °C, which is the initial sintering stage of MIM 420. MIM 420Nb showed the slowest sintering rate due to the strong binding force between Nb and C. At 1350 °C, the sintering densities of MIM 420 and 420 + 0.3C slightly improved, whereas their grain sizes grew significantly. Scanning electron microscopy images show grain boundary-pore separation, which significantly retarded the grain boundary diffusion mechanism and hence reduced the densification rate. The addition of C accelerated the pore-grain boundary separation; thus MIM 420 + 0.3C showed the lowest density at this temperature among the materials analyzed in this study. Nb suppressed the grain growth rate; thus, MIM 420Nb exhibited the highest density among the three materials. At 1370 °C, MIM 420 + 0.3C reached the highest density owing to the creation of a liquid phase. Theoretical calculations proved that there is a linear relationship between the grain boundary area per unit volume and the interfacial pore area per unit volume. Furthermore, when the ratio of grain size to pore size is 28, the contact probability between the grain boundaries and pores is significantly reduced to approximately 10%, leading to an extremely slow densification rate and a rapid grain growth rate, which is consistent with the experimental results. Full article

Inhalation exposures to nanoparticles (NPs) from printers and photocopiers have been associated with upper airway and systemic inflammation, increased blood pressure, and cases of autoimmune and respiratory disorders. In this study we investigate oxidative stress induced by exposures to copier-emitted nanoparticles using a panel of urinary oxidative stress (OS) biomarkers representing DNA damage (8-hydroxydeoxyguanosine, 8-OHdG; 8-hydroxyguanosine, 8-OHG; 5-hydroxymethyl uracil 5-OHMeU), lipid peroxidation (8-isoprostane; 4-hydroxynonenal, HNE), and protein oxidation biomarkers (o-tyrosine, 3-chlorotyrosine, and 3-nitrotyrosine) under conditions of acute (single 6 h exposure, 9 volunteers, 110 urine samples) and chronic exposures (6 workers, 11 controls, 81 urine samples). Urinary biomarkers were quantified with liquid chromatography–tandem mass spectrometry after solid phase extraction sample cleanup. 8-OHdG, 8-OHG, 8-isoprostane, and HNE were significantly elevated in both the acute and chronic exposure study participants relative to the controls. In the acute exposure study, the geometric mean ratios post-/pre-exposure were 1.42, 1.10, 2.0, and 2.25, respectively. Urinary 8-OHG and HNE increased with time to at least 36 h post-exposure (post-/pre-exposure GM ratios increased to 3.94 and 2.33, respectively), suggesting slower generation and/or urinary excretion kinetics for these biomarkers. In chronically exposed operators, the GM ratios of urinary biomarkers relative to controls ranged from 1.52 to 2.94, depending on the biomarker. O-Tyrosine and 5-OHMeU biomarkers were not significantly different from the controls. 3-chlorotyrosine and 3-nitrotyrosine were not detected in the urine samples. We conclude that NPs from photocopiers induce systemic oxidative stress by damaging DNA, RNA, and lipids. Urinary levels of 8-OHdG, 8-OHG, HNE, and 8-isoprostane were orders of magnitude higher than in nanocomposite processing workers, comparable to nano titanium dioxide and fiberglass manufacturing workers, but much lower than in shipyard welding and carbon nanotube synthesis workers. Biomarkers 8-OHdG, 8-OHG, 8-isoprostane, and HNE appear to be more sensitive and robust urinary biomarkers for monitoring oxidative stress to NPs from photocopiers. Full article

A washing ejector is a pre-treatment technology used to remediate contaminated soil by separating fine particles. The washing ejector developed in this study is a device that utilizes fast liquid jets to disperse soil aggregates by cavitation flow. The cavitation phenomenon is affected by the Bernoulli principle, and the liquid pressure decreases with the increase in kinetic energy. The cavitating flow of the fluid through the Ventrui nozzle can remove surface functional groups and discrete particles. The main methodology involves the removal of small particles bound to coarse particles and the dispersion of soil aggregates. Particle collisions occur on the surface soil, such as the metal phase that is weakly bound to silicate minerals. It was observed that the dispersed soil affected the binding of toxic heavy metals and the mineralogical characteristics of the soil. The quantity of oxides, organic matter, and clay minerals affected the properties of the soil. An almost 40–60% removal efficiency of total metals (As, Zn, and Pb) was obtained from the contaminated soils. After treatment by a washing ejector, the volume of fine particles was reduced by 28–47%. When the contaminants are associated with particulates, separation using a washing ejector can be more effective. Therefore, physical separation improves the removal efficiency of heavy metals from soil aggregates. Full article

The biggest challenge faced in oil refineries is the removal of sulfur compounds in fuel oil. The sulfur compounds which are found in fuel oil such as gasoline and diesel, react with oxygen in the atmosphere to produce sulfur oxide (SOx) gases when combusted. These sulfur compounds produced from the reaction with oxygen in the atmosphere may result in various health problems and environmental effects. Hydrodesulfurization (HDS) is the conventional process used to remove sulfur compounds from fuel oil. However, the high operating conditions required for this process and its inefficiency in removing the organosulfur compounds turn to be the major drawbacks of this system. Researchers have also studied several alternatives to remove sulfur from fuel oil. The use of ionic liquids (ILs) has also drawn the interest of researchers to incorporate them in the desulfurization process. The environmental effects resulting from the use of these ILs can be eliminated using eutectic-based ionic liquids (EILs), which are known as greener solvents. In this research, a combination of extractive desulfurization (EDS) and oxidative desulfurization (ODS) using a photocatalyst and EIL was studied. The photocatalyst used is a pre-reported catalyst, Cu-Fe/TiO₂ and the EIL were synthesized by mixing choline chloride (ChCl) with organic acids. The acids used for the EILs were propionic acid (PA) and p-toluenesulfonic acid (TSA). The EILs synthesized were characterized using thermogravimetry analyser (TGA) differential scanning calorimetry (DSC) analysis to determine the physical properties of the EILs. Based on the TGA analysis, ChCl (1): PA (3) obtained the highest thermal stability whereas, as for the DSC analysis, all synthesized EILs have a lower melting point than its pure component. Further evaluation on the best EIL for the desulfurization process was carried out in a photo-reactor under UV light in the presence of Cu-Fe/TiO₂ photocatalyst and hydrogen peroxide (H₂O₂). Once the oxidation and extraction process were completed, the oil phase of the mixture was analyzed using high performance liquid chromatography (HPLC) to measure the sulfur removal efficiency. In terms of the desulfurization efficiency, the EIL of ChCl (1): TSA (2) showed a removal efficiency of about 99.07%. Full article

Biothiols are extremely powerful antioxidants that protect cells against the effects of oxidative stress. They are also considered relevant disease biomarkers, specifically risk factors for cardiovascular disease. In this paper, a new procedure for the simultaneous determination of human serum albumin and low-molecular-weight thiols in plasma is described. The method is based on the pre-column derivatization of analytes with a thiol-specific fluorescence labeling reagent, monobromobimane, followed by separation and quantification through reversed-phase high-performance liquid chromatography with fluorescence detection (excitation, 378 nm; emission, 492 nm). Prior to the derivatization step, the oxidized thiols are converted to their reduced forms by reductive cleavage with sodium borohydride. Linearity in the detector response for total thiols was observed in the following ranges: 1.76–30.0 mg mL⁻¹ for human serum albumin, 0.29–5.0 nmol mL⁻¹ for α-lipoic acid, 1.16–35 nmol mL⁻¹ for glutathione, 9.83–450.0 nmol mL⁻¹ for cysteine, 0.55–40.0 nmol mL⁻¹ for homocysteine, 0.34–50.0 nmol mL⁻¹ for N-acetyl-L-cysteine, and 1.45–45.0 nmol mL⁻¹ for cysteinylglycine. Recovery values of 85.16–119.48% were recorded for all the analytes. The developed method is sensitive, repeatable, and linear within the expected ranges of total thiols. The devised procedure can be applied to plasma samples to monitor biochemical processes in various pathophysiological states. Full article