Search Results (6)

Carbon dioxide (CO₂) capture using alkanolamines remains the most mature technology, yet faces challenges including solvent loss, high regeneration energy and equipment corrosion. Ionic liquids (ILs) are proposed as alternatives, but their high viscosity and production costs hinder industrial use. Thus, blending ILs with amines offers a promising approach. This work presents new experimental data for aqueous blends of 1-butyl-3-methylimidazolium hydrogen sulfate, $\left[\mathrm{B}\mathrm{m}\mathrm{i}{\mathrm{m}}^{+}\right]\left[\mathrm{H}\mathrm{S}{\mathrm{O}}_4^{-}\right],$ with 2-amino-2-methyl-1-propanol (AMP) and 3-(methylamino)propylamine (MAPA) and for choline glycine, $\left[\mathrm{C}{\mathrm{h}}^{+}\right]\left[\mathrm{G}\mathrm{l}{\mathrm{y}}^{-}\right]$, with AMP, modeled using the modified Kent–Eisenberg approach. It was shown that substituting a portion of the amine with $\left[\mathrm{B}\mathrm{m}\mathrm{i}{\mathrm{m}}^{+}\right]\left[\mathrm{H}\mathrm{S}{\mathrm{O}}_4^{-}\right]$ reduces CO₂ uptake per mole of amine due to the lower solution’s basicity, despite the added sites for physical absorption. In contrast, the replacement of an amine portion with $\left[\mathrm{C}{\mathrm{h}}^{+}\right]\left[\mathrm{G}\mathrm{l}{\mathrm{y}}^{-}\right]$ enhances both physical and chemical interactions, leading to increased CO₂ solubility per mole of amine. Finally, replacing a small portion of water with $\left[\mathrm{C}{\mathrm{h}}^{+}\right]\left[\mathrm{G}\mathrm{l}{\mathrm{y}}^{-}\right]$ does not significantly alter the bulk CO₂ solubility (moles of CO₂ per kg of solvent) but lowers the solvent’s vapor pressure. Given the non-toxic nature of $\left[\mathrm{C}{\mathrm{h}}^{+}\right]\left[\mathrm{G}\mathrm{l}{\mathrm{y}}^{-}\right]$, the resulting solvent poses no added environmental risk. Model predictions agree well with experimental data (deviations of 2.0–11.6%) and indicate low unreacted amine content at CO₂ partial pressures of 1–10 kPa for carbamate-forming amines, i.e., $\left[\mathrm{G}\mathrm{l}{\mathrm{y}}^{-}\right]$, and MAPA. Consequently, at higher CO₂ partial pressures, the solubility increases due to carbamate hydrolysis and molecular CO₂ dissolution. Full article

This research addresses the critical challenge of CO₂ capture by exploring innovative ways to avoid ethane (C₂H₆) co-absorption in natural gas sweetening operations. The solubility of Ethane (C₂H₆) was measured in three ionic liquids (ILs) with similar anions, 1-decyl-3-methyl imidazolium bis (trifluoro methylsulfonyl imide) [IL-1], 1-hexadecyl-3-methylimidazolium bis (trifluoro methylsulfonyl imide) [IL-2], and triethytetra-decyl ammonium bis (trifluoromethylsulfonyl imide) [IL-3]. The solubility experiments were investigated at 303.15 K and 343.15 K with pressures reaching 1.2 MPa. Among the ILs, [IL-2] exhibited the highest ethane absorption capacity due to its extended alkyl chain. The Peng-Robinson equation of state (PR-EoS) and three (3) distinct mixing rules provided robust correlations for the solubility data. Results demonstrate the inferior performance of [IL-1], [IL-2], and [IL-3] compared to Selexol/Genosorb 1753. The selectivity of Ethane (C₂H₆) over CO₂ was determined, with the overall selectivity ranking as follows: [IL-1] > [IL-3] > [IL-2]. A comparison of these selectivity values with published IL data indicated that these three ILs are most effective when used in applications targeting CO₂ capture in the absence of Ethane (C₂H₆), such as in the case of flue gas. They will most probably be used with an amine blend. Additionally, the Enthalpy and entropy of absorption provided valuable insights, demonstrating Ethane’s weaker interactions and lower solubility than CO₂. These findings emphasize the critical role of IL structure in determining ethane solubility and highlight the potential of customized ILs for optimizing gas-separation processes. Full article

Global warming and climate changes are among the biggest modern-day environmental problems, the main factor causing these problems is the greenhouse gas effect. The increased concentration of carbon dioxide in the atmosphere resulted in capturing increased amounts of reflected sunlight, causing serious acute and chronic environmental problems. The concentration of carbon dioxide in the atmosphere reached 421 ppm in 2022 as compared to 280 in the 1800s, this increase is attributed to the increased carbon dioxide emissions from the industrial revolution. The release of carbon dioxide into the atmosphere can be minimized by practicing carbon capture utilization and storage methods. Carbon capture utilization and storage (CCUS) has four major methods, namely, pre-combustion, post-combustion, oxyfuel combustion, and direct air capture. It has been reported that applying CCUS can capture up to 95% of the produced carbon dioxide in running power plants. However, a reported cost penalty and efficiency decrease hinder the wide applicability of CCUS. Advancements in the CCSU were made in increasing the efficiency and decreasing the cost of the sorbents. In this review, we highlight the recent developments in utilizing both physical and chemical sorbents to capture carbon. This includes amine-based sorbents, blended absorbents, ionic liquids, metal-organic framework (MOF) adsorbents, zeolites, mesoporous silica materials, alkali-metal adsorbents, carbonaceous materials, and metal oxide/metal oxide-based materials. In addition, a comparison between recently proposed kinetic and thermodynamic models was also introduced. It was concluded from the published studies that amine-based sorbents are considered assuperior carbon-capturing materials, which is attributed to their high stability, multifunctionality, rapid capture, and ability to achieve large sorption capacities. However, more work must be done to reduce their cost as it can be regarded as their main drawback. Full article

The preparation, characterization and gas separation properties of mixed matrix membranes (MMMs) were obtained from polyimide capped with ionic liquid and blended with metal-organic frameworks (MOFs). The synthesized MOF was amine functionalized to produce UiO-66-NH₂, and its amino group has a higher affinity for CO₂. Mixed matrix membranes exhibited good membrane forming ability, heat resistance and mechanical properties. The polyimide membrane exclusively capped by ionic liquid exhibited good permselectivity of 74.1 for CO₂/CH₄, which was 6.2 times that of the pure polyimide membrane. It is worth noting that MMM blended with UiO-66-NH₂ demonstrated the highest ideal selectivity for CO₂/CH₄ (95.1) with a CO₂ permeability of 7.61 Barrer, which is close to the 2008 Robeson upper bound. The addition of UiO-66-NH₂ and ionic liquid enhanced the permselectivity of MMMs, which may be one of the promising technologies for high performance CO₂/CH₄ gas separation. Full article

Nanofibers mats derived from the task-specific functionalized polymeric ionic liquids based on homocysteine thiolactone are obtained by electrospinning them as blends with polyvinylpyrrolidone. The presence of this functional moiety allowed the post-functionalization of these mats through the aminolysis of the thiolactone ring in the presence of an amine by a thiol–alkene “click” reaction. Under controlled experimental conditions the modification can be performed introducing different functionalization and crosslinking of the electrospun fibers, while maintaining the nanostructure obtained by the electrospinning. Initial studies suggest that the nanofibers based on these functionalized polymeric ionic liquids can be used in both sensing and catalytic applications. Full article

A wide variety of quaternary ammonium compounds (QACs) have escalated the attraction of researchers to explore the application of QACs. The compounds have frequently been synthesized through alkylation or quaternization of tertiary amines with alkyl halides. Recently, QACs have been applied to compatibilize polymer blends and polymer composites in improving their thermo-mechanical properties. This concise review concentrates on the application of two types of QACs as compatibilizers for polymer blends and polymer composites. The types of QACs that were effectively applied in the blends and composites are quaternary ammonium surfactants (QASs) and quaternary ammonium ionic liquids (QAILs). They have been chosen for the discussion because of their unique chemical structure which can interact with the polymer blend and composite components. The influence of QASs and QAILs on the thermo-mechanical properties of the polymer blends and polymer composites is also described. This review could be helpful for the polymer blend and polymer composite researchers and induce more novel ideas in this research area. Full article