Search Results (5)

In recent years, underground hydrogen storage (UHS) has become a hot topic in the field of deep energy storage. Green hydrogen, produced using surplus electricity during peak production, can be injected and stored in underground reservoirs and extracted during periods of high demand. A profound understanding of the mechanisms of the gas–water two-phase flow at the pore scale is of great significance for evaluating the sealing integrity of UHS reservoirs and optimizing injection, as well as the storage space. The pore structure of rocks, as the storage space and flow channels for fluids, has a significant impact on fluid injection, production, and storage processes. This paper systematically summarizes the methods for characterizing the micro-pore structure of reservoir rocks. The applicability of different techniques was evaluated and compared. A detailed comparative analysis was made of the advantages and disadvantages of various numerical simulation methods in tracking two-phase flow interfaces, along with an assessment of their suitability. Subsequently, the microscopic visualization seepage experimental techniques, including microfluidics, NMR-based, and CT scanning-based methods, were reviewed and discussed in terms of the microscopic dynamic mechanisms of complex fluid transport behaviors. Due to the high resolution, non-contact, and non-destructive, as well as the scalable in situ high-temperature and high-pressure experimental conditions, CT scanning-based visualization technology has received increasing attention. The research presented in this paper can provide theoretical guidance for further understanding the characterization of the micro-pore structure of reservoir rocks and the mechanisms of two-phase flow at the pore scale. Full article

All-inorganic perovskite nanocrystals (NCs) have attractive potential for applications in display and lighting fields due to their special optoelectronic properties. However, they still suffer from poor water and thermal stability. In this work, green CsPbBr₃-alginic acid (CsPbBr₃-AA) perovskite composites were synthesized by an in situ hot-injection process which showed a high photoluminescence quantum yield (PLQY) of 86.43% and improved moisture and thermal stability. Finally, white light-emitting diodes (WLEDs) were fabricated by combining the green CsPbBr₃-AA perovskite composites with red K₂SiF₆:Mn⁴⁺ phosphors and blue InGaN LED chips. The WLEDs show a relatively high luminous efficacy of 36.4 lm/W and a wide color gamut (124% of the National Television System Committee). These results indicate that the green CsPbBr₃-AA perovskite composites have great potential applications in backlight displays. Full article

During in situ modification, inappropriate thermal insulation measures applied in annulus of injection wells will cause injection technical problems such as tremendous heat loss, wellhead lifting, serious casing damages, and corrosion. Continuous nitrogen injection into annulus is an effective measure to realize thermal insulation of injection wells. The critical displacement parameters of nitrogen injection in annulus are a key factor in the process of continuous nitrogen injection. However, the critical nitrogen injection rate under various working conditions, such as different well types, different wellhead steam parameters, and insulation pipe parameters, was not fully considered and studied. In this paper, the annular critical nitrogen injection displacement model was established based on the completion structure of injection well by applying the basic principles of heat transfer and fluid mechanics comprehensively. The influencing factors of critical nitrogen injection displacement were calculated and analyzed. The results show that the annular thermal resistance of horizontal wells is larger than that of directional wells for different well types, and the critical nitrogen injection displacement required is higher. The parameter sensitivity analysis shows that with the increase of pressure, steam displacement, and steam dryness, the required critical nitrogen injection displacement rate increases nearly quadratically. However, with the increase of the length and thermal conductivity of insulation pipe, the critical nitrogen injection displacement decreases cubically. The critical nitrogen injection can be reduced by reducing the annular area of the casing annulus and lowering the string deeply. The research results can provide key basic theoretical guidance for improving the heat utilization efficiency of in situ modified wells and reducing the casing damage rate for hot injection wells. Full article

The hot exhaust gas generated by a downhole combustion heater directly heats the formation, which can avoid the heat loss caused by the injection of high-temperature fluid on the ground. However, if the temperature of the exhaust gas is too high, it may lead to the carbonization of organic matter in the formation, which is not conducive to oil production. This paper proposes the use of low-temperature catalytic combustion of a mixture of methane and air to produce a suitable exhaust gas temperature. The simulation studies the influence of different parameters on the catalytic combustion characteristics of methane and the influence of downhole high-pressure conditions. The results show that under high-pressure conditions, using a smaller concentration of methane (4%) for catalytic combustion can obtain a higher conversion efficiency (88.75%), and the exhaust temperature is 1097 K. It is found that the high-pressure conditions in the well can promote the catalytic combustion process of the heater, which proves the feasibility of the downhole combustion heater for in situ heating of unconventional oil and gas reservoirs. Full article

Leaking underground storage tanks (USTs) containing gasoline represent a significant public health hazard. Virtually undetectable to the UST owner, gasoline leaks can contaminate groundwater supplies. In order to develop remediation plans one must know the extent of gasoline contamination. Centrifugal simulations showed that in silty and sandy soils gasoline moved due to the physical process of advection and was retained as a pool of free products above the water table. However, in clayey soils there was a limited leak with lateral spreading and without pooling of free products above the water table. Amount leaked depends on both the type of soil underneath the USTs and the amount of corrosion. The soil vapor extraction (SVE) technology seems to be an effective method to remove contaminants from above the water table in contaminated sites. In-situ air sparging (IAS) is a groundwater remediation technology for contamination below the water table, which involves the injection of air under pressure into a well installed into the saturated zone. However, current state of the art is not adequate to develop a design guide for site implementation. New information is being currently generated by both centrifugal tests as well as theoretical models to develop a design guide for IAS. The petroleum contaminated soils excavated from leaking UST sites can be used for construction of highway pavements, specifically as sub-base material or blended and used as hot or cold mix asphalt concrete. Cost analysis shows that 5% petroleum contaminated soils is included in hot or cold mix asphalt concrete can save US$5.00 production cost per ton of asphalt produced. Full article