Search Results (12)

The study of energy savings in ventilation systems within buildings is crucial. Impinging jet ventilation (IJV) systems have garnered significant interest from researchers. The identification of the appropriate location for the IJV reveals a gap in the existing literature. This research was conducted to address the existing gap by examining the impact of IJV location on energy savings and thermal comfort. A comprehensive three-dimensional CFD model is examined to accurately simulate the real environment of an office room (3 × 3 × 2.9 m³) during cooling mode, without the application of symmetrical plans. Four locations have been selected: two at the corners and two along the midwalls, designated for fixed-person positions. The return vent height is analyzed utilizing seven measurements: 2.9, 2.6, 2.3, 1.7, 1.1, 0.8, and 0.5 m. The RNG k–ε turbulence model is implemented alongside enhanced wall treatment. The findings indicated that the optimal range for the return vent height is between 1.7 and 0.8 m. It is advisable to utilize the IJV midwall 1 location, positioned behind the seated individual and away from the exterior hot wall. It is characterized by low vortex formation in the local working zone that contributes to a more comfortable sensation while providing recognized energy-saving potential. Full article

Transient receptor potential (TRP) channels are broadly implicated in the developmental programs of most tissues. Amongst these tissues, skeletal muscle and adipose are noteworthy for being essential in establishing systemic metabolic balance. TRP channels respond to environmental stimuli by supplying intracellular calcium that instigates enzymatic cascades of developmental consequence and often impinge on mitochondrial function and biogenesis. Critically, aminoglycoside antibiotics (AGAs) have been shown to block the capacity of TRP channels to conduct calcium entry into the cell in response to a wide range of developmental stimuli of a biophysical nature, including mechanical, electromagnetic, thermal, and chemical. Paradoxically, in vitro paradigms commonly used to understand organismal muscle and adipose development may have been led astray by the conventional use of streptomycin, an AGA, to help prevent bacterial contamination. Accordingly, streptomycin has been shown to disrupt both in vitro and in vivo myogenesis, as well as the phenotypic switch of white adipose into beige thermogenic status. In vivo, streptomycin has been shown to disrupt TRP-mediated calcium-dependent exercise adaptations of importance to systemic metabolism. Alternatively, streptomycin has also been used to curb detrimental levels of calcium leakage into dystrophic skeletal muscle through aberrantly gated TRPC1 channels that have been shown to be involved in the etiology of X-linked muscular dystrophies. TRP channels susceptible to AGA antagonism are critically involved in modulating the development of muscle and adipose tissues that, if administered to behaving animals, may translate to systemwide metabolic disruption. Regenerative medicine and clinical communities need to be made aware of this caveat of AGA usage and seek viable alternatives, to prevent contamination or infection in in vitro and in vivo paradigms, respectively. Full article

Renewable energy resources require energy storage techniques to curb problems with intermittency. One potential solution is the use of phase change materials (PCMs) in latent heat thermal energy storage (LHTES) systems. Despite the high energy storage density of PCMs, their thermal response rate is restricted by low thermal conductivity. The topic of heat transfer enhancement techniques for increasing thermal performance of LHTES systems has mainly focused on passive heat transfer enhancement techniques with less attention towards active methods. Active heat transfer enhancement techniques require external power supplied to the system. In this paper, recent advances in active heat transfer enhancement techniques within LHTES systems are reviewed, including mechanical aids, vibration, jet impingement, injection, and external fields. The pertinent findings related to the field are summarized in relation to the charging and discharging processes of PCMs. Suggestions for future research are proposed, and the importance of additional energy input for storage is discussed. Full article

The corner impinging jet ventilation is a new air distribution system for use in office environments. This study reports the mean flow field behavior of dual isothermal corner-placed inlets based on an impinging jet in a square-shaped room with the size of 7.2 m × 7.2 m. A detailed numerical study is carried out to evaluate the influence the different configuration parameters, such as the inlet placement, same side or opposite side, and supply airflow rate, have on the flow field. The results show that the highest velocity peak for all cases is obtained at x = 0.5 m and the lowest at x = 3.5 m. The velocity profiles development remains similar when increasing the flow rate. For the zone evaluation, the results show that Case 1 and 2 (V = 20 L/s) meet the requirement of not exceeding 0.15 m/s during the heating season in the occupied zone according the BBR standard both for same-side and opposite-side configurations. For Case 4, the optimal placement of the inlets is opposite to each other when V = 30 L/s for the BBR requirements. Case 1, 2, 3, 4, 5, and 7 all meet the requirement of not exceeding 0.25 m/s during the cooling season both for the same-side and opposite-side configurations. For Case 8, the optimal placement of the inlets is opposite to each other when V = 50 L/s. Full article

Modern low-pressure turbine engines are equipped with casings impingement cooling systems. Those systems (called Active Clearance Control) are composed of an array of air nozzles, which are directed to strike turbine casing to absorb generated heat. As a result, the casing starts to shrink, reducing the radial gap between the sealing and rotating tip of the blade. Cooling air is delivered to the nozzles through distribution channels and collector boxes, which are connected to the main air supply duct. The application of low-pressure turbine cooling systems increases its efficiency and reduces engine fuel consumption. Full article

In this paper, we compare using computational fluid dynamics the aero-thermal performance of two candidate casing manifolds for supplying an impingement-actuated active tip clearance control system for an aero-engine high-pressure turbine. The two geometries are (a) single-entry: an annular manifold fed at one circumferential location; (b) multiple-entry: a casing manifold split into four annular sectors, with each sector supplied separately from an annular ring main. Both the single-entry and multiple-entry systems analysed in this paper are idealised versions of active clearance control systems in current production engines. Aero-thermal performance is quantitatively assessed on the basis of the heat transfer coefficient distribution, driving temperature difference for heat transfer between the jet and casing wall and total pressure loss within the high-pressure turbine active clearance control system. We predict that the mean heat transfer coefficient (defined with respect to the inlet temperature and local wall temperature) of the single-entry active clearance control system is 77% greater than the multiple-entry system, primarily because the coolant in the multiple-entry case picks up approximately 40 K of temperature from the ring main walls, and secondarily because the average jet Reynolds number of impingement holes in the single-entry system is 1.2 times greater than in the multiple-entry system. The multiple-entry system exhibits many local hot and cold spots, depending on the position of the transfer boxes, while the single-entry case has a more predictable aero-thermal field across the system. The multiple-entry feed system uses an average of 20% of the total available pressure drop, while the feed system for the single-entry geometry uses only 2% of the total available pressure drop. From the aero-thermal results of this computational study, and in consideration of holistic aero-engine design factors, we conclude that a single-entry system is closer to an optimal solution than a multiple-entry system. Full article

The photovoltaic cell temperature is a key factor in solar energy harvesting. Solar radiation raises temperature on the cell, lowering its peak efficiency. Air jet impingement is a high heat transfer rate system and has been previously used to cool the back surface of photovoltaic modules and cells. In this work, an experimental comparison of the cooling performance of two different air jet impingement crossflow schemes was performed. Crossflow is defined as the air mass interacting with a certain jet modifying its movement. This leads to a change in its heat exchange capabilities and is related with the inlet-outlet arrangement of the fluid. In this work, zero and minimum crossflow schemes were compared. The main contribution of this work considered the consumption of the flow supplying devices to determine the most suitable system. The best configuration increased the net power output of the cell by 6.60%. These results show that air impingement cooling can play a role in increasing photovoltaic profitability. In terms of uniformity, on small impingement plates with a low number of nozzles, the advantages expected from the zero crossflow configuration did not stand out. Full article

The 650–621 Ma plume which impinged beneath the Siberian craton during the breakup of Rodinia caused the formation of several alkaline carbonatite massifs in craton margins of the Angara rift system. The Beloziminsky alkaline ultramafic carbonatite massif (BZM) in the Urik-Iya graben includes alnöites, phlogopite carbonatites and aillikites. The Yuzhnaya pipe (YuP) ~ 645 Ma and the 640–621 Ma aillikites in BZM, dated by ⁴⁰Ar/³⁹Ar, contain xenoliths of carbonated sulfide-bearing dunites, xenocrysts of olivines, Cr-diopsides, Cr-phlogopites, Cr-spinels (P ~ 4–2 GPa and T ~ 800–1250 °C) and xenocrysts of augites with elevated HFSE, U, Th. Al-augites and kaersutites fractionated from T ~ 1100–700 °C along the 90 mW/m² geotherm. Higher T trend for Al-Ti augite, pargasites, Ti-biotites series (0.4–1.5 GPa) relate to intermediate magma chambers near the Moho and in the crust. Silicate xenocrysts show Zr-Hf, Ta-Nb peaks and correspond to carbonate-rich magma fractionation that possibly supplied the massif. Aillikites contain olivines, rare Cr-diopsides and oxides. The serpentinites are barren, fragments of ore-bearing Phl carbonatites contain perovskites, Ta-niobates, zircons, thorites, polymetallic sulphides and Ta-Mn-Nb-rich magnetites, ilmenites and Ta-Nb oxides. The aillikites are divided by bulk rock and trace elements into seven groups with varying HFSE and LILE due to different incorporation of carbonatites and related rocks. Apatites and perovskites reveal remarkably high LREE levels. Aillikites were generated by 1%–0.5% melting of the highly metasomatized mantle with ilmenite, perovskite apatite, sulfides and mica, enriched by subduction-related melts and fluids rich in LILE and HFSE. Additional silicate crystal fractionation increased the trace element concentrations. The carbonate-silicate P-bearing magmas may have produced the concentration of the ore components and HFSE in the essentially carbonatitic melts after liquid immiscibility in the final stage. The mechanical enrichment of aillikites in ore and trace element-bearing minerals was due to mixture with captured solid carbonatites after intrusion in the massif. Full article

Experimental activity has been performed to study different impingement cooling schemes in static and rotating conditions. Geometry replicates a leading-edge cold bridge system, including a radial supply channel and five rows of film-cooling and showerhead holes. Two impingement geometries have been studied, with different numbers of holes and diameters but with equal overall passage area. Reynolds numbers up to 13,800 and rotation numbers up to 0.002 have been investigated (based on an equivalent slot width). Tests have been performed using a novel implementation of transient heat transfer technique, which allows correct replication of the sign of buoyancy forces by flowing ambient temperature air into a preheated test article. Results show that complex interactions occur between the different features of the system, with a particularly strong effect of jet supply condition. Rotation further interacts with these phenomena, generally leading to a slight decrease in heat transfer. Full article

A radio frequency identifier (RFID) tag sensor for the real time monitoring of cracks in civil engineering building is presented in this work. The RFID tag is equipped with a piezoelectric sensor able to detect small movements of crack in order to prevent collapses of buildings or civil engineering structures. The information is delivered by using the modulated scattering technique (MST) which permits to obtain high operative ranges. The sensor is passive, the power supply is provided by means of a suitable rect-antenna and a Chockcroft-Walton multiplier circuit powered by means of the impinging interrogating electromagnetic wave. A system prototype, operating in the X band at 10 GHz, has been designed fabricated and experimentally assessed in a realistic scenario obtaining promising results. Full article

Following a comprehensive review on titanium machining and methods of cutting fluid application, this paper presents a new Controlled cutting fluid impinging supply system (Cut‐list) developed to deliver an accurate amount of cutting fluid into the machining zone via wellpositioned coherent nozzles based on the calculation of the heat generated. The performance of the new system was evaluated against a conventional flood cutting fluid supply system during step shoulder milling of Ti‐6Al‐4V using vegetable oil‐based cutting fluid. The comparison was performed at different cutting speeds and feed rates. Comparison measures/indicators were cutting force, workpiece temperature, tool flank wear, burr formation and average surface roughness (Ra). The new system provided significant reductions in cutting fluid consumption of up to 42%. Additionally, reductions in cutting force, tool flank wear and burr height of 16.41%, 46.77%, and 31.70% were recorded, respectively. Smaller Ra values were also found with the use of the new system. Full article

Ballast water systems in large LNG carriers are essential for proper operations and stability. Water withdrawn from the surrounding environment to supply to the ballast can pose entrainment and impingement risk to the resident fish population. Quantification of these risks and the net effect on population is usually quite challenging and complex. Various methods over the last several decades have been developed and are available in the literature for quantification of entrainment of mobile and immobile lifestages of resident fish. In this study, a detailed 3-dimensional model was developed to estimate the entrainment of ichthyoplankton (fish eggs and larvae) and fish from an estuarine environment during the repeated short-term operation of a ballast water intake for an LNG carrier. It was also used to develop a zone of influence to determine the ability of mobile life stages to avoid impingement. The ichthyoplankton model is an Equivalent Adult Model (EAM) and assesses the number of breeding adults lost to the population. The EAM incorporates four different methods developed between 1978 and 2005. The study also considers the uncertainty in estimates for the lifestage data and, as such, performs sensitivity analyses to evaluate the confidence level achievable in such quantitative estimates for entrainment. Full article