Search Results (54)

This study presents the development of a one-part phosphate-activated geopolymer foam based on fayalite flotation residue from the copper industry. The solid activator consisted of triple superphosphate, enabling a dry-mix binder that requires only water addition prior to use. Foamed materials were characterized by XRD, FTIR, Mössbauer spectroscopy, DSC-TG, hot-stage microscopy, SEM-EDX and physical and mechanical testing. The foaming of the geopolymer reduced the densities between 0.753 and 2.15 g/cm³, relative porosities up to 73.6%, and compressive strengths ranging from 1.4 to 28.8 MPa. The foamed geopolymer maintained dimensional stability up to about 1000 °C. The thermal conductivity coefficient measured on large-sized specimen blocks was 0.099 W/mK at a density of 0.753 g/cm³. These results demonstrate that fayalite slag can be effectively utilized as a precursor for sustainable geopolymer foams combining low thermal conductivity, high thermal stability, and the utilization of industrial by-products. Full article

Copper smelter slag represents a significant secondary resource of critical metals, while flotation tailings serve as an abundant sulfur-bearing waste stream. This study investigated a waste-on-waste sulfation roasting approach for the selective recovery of Cu, Ni, and Co from fayalite copper smelter slag using flotation tailings as an in situ sulfur source and sodium metabisulfite (SMBS, Na₂S₂O₅) as a sulfation promoter. The effects of roasting temperature, roasting time, slag-to-tailings ratio, SMBS dosage, and water-leaching conditions were systematically evaluated. Under the optimum conditions of a slag-to-tailings ratio of 1:1, roasting at 600 °C for 4 h with 30 wt% SMBS addition, followed by water leaching at 25 °C for 2 h, extraction efficiencies of 85.5% Cu, 81.6% Ni, and 87.1% Co were achieved, while Fe dissolution remained below 5%, demonstrating high selectivity. Phase and microstructural analyses by XRD, FTIR, SEM, and TG–DTA revealed that pyrite oxidation generated sulfur oxides required for metal sulfation, whereas SMBS promoted sulfur release and sulfate stabilization, enhancing sulfation efficiency. Thermodynamic analysis further confirmed the feasibility of sulfide oxidation and sulfate formation within the investigated temperature range. The results demonstrate that the synergistic use of tailings and SMBS enables efficient low-temperature sulfation roasting of fayalite slag and provides a promising route for the selective recovery of valuable metals from metallurgical waste materials. Full article

Top Submerged Lance (TSL) technology is widely used in non-ferrous smelting, yet in-situ bath dynamics remain challenging to quantify because the process operates in a closed, high-temperature, highly turbulent and optically inaccessible environment. The absence of direct diagnostics limits the ability to relate operating conditions to bubble dynamics, gas penetration and bath agitation and constrains validation of multiphase CFD models under realistic conditions. This study introduces a multimodal sensing framework that combines spectral acoustic analysis with lance-mounted inertial motion sensing to characterize dynamic bath behavior across cold-model, laboratory-scale and pilot-scale systems. Water-glycerin experiments establish repeatable acoustic signatures of individual bubble-collapse events, with dominant emission bands in the 300–900 Hz range and higher-frequency components extending into the kilohertz domain. High-temperature laboratory trials using fayalitic slag reproduce these frequency regions while exhibiting depth-dependent attenuation and clear spectral separation between submerged and non-submerged lance operation. Power Spectral Density (PSD) and cumulative spectral power analyses resolve the influence of gas flow rate and lance submersion depth on acoustic spectral power distribution, while inertial measurements capture corresponding increases in vertical lance acceleration associated with back-pressure fluctuations. Pilot-scale trials at 120 Nm³/h air and 13 L/h diesel confirm that shallow lance submersion substantially increases measured acoustic spectral power below 3 kHz, whereas deeper penetration enhances periodic vertical acceleration response measured by the inertial sensor. The combined acoustic-inertial methodology provides a physically interpretable and cross-scale framework for assessing bubble collapse activity, plume interaction and bath agitation under high-temperature TSL conditions. The approach enables frequency-based diagnostics that can be systematically compared with CFD predictions of plume oscillation and collapse-related dynamics. Once baseline frequency ranges are established for a given slag system, the method can support process monitoring and may provide indirect indicators related to changes in surface agitation or foaming tendency, enabling structured data-driven analysis. The framework thus provides a practical bridge between cold-model experiments, high-temperature measurements, multiphase modeling and industrial TSL operation. Full article

Hydrogen plasma heating, a unique method for heating and reducing iron ore, is distinguished by its high heat, rapid reduction, and high efficiency, making it a promising technique in the metallurgy field. In this study, a non-transferred arc plasma heating system was used with Ar-H₂ as the working gas and acidic pellets as the raw material. The microstructures and elemental distributions of the slag and iron phases during the reduction process were examined using electron microscopy and energy-dispersive X-ray. The variation patterns of Fe-containing phases in the reduction products were found using X-ray diffraction and full-spectrum fitting refinement. The conversion rate of the oxidized pellets and the deoxidation conversion rate per area were estimated for various gas flow rates and reduction times. A reaction kinetics model was also used to study the reaction controlling step. The results showed that during the reduction process, with an H₂ flow rate of 4.5 L min⁻¹ and a 40 min reduction, the conversion(α) reached 99.89% and the purity of the reduced metallic iron reached 99.9%, achieving the industrial-grade 3N standard. Si and Al in the melt bath generated fayalite (Fe₂SiO₄) and hercynite (FeAl₂O₄) with Fe_xO. The deoxidation conversion rate per unit area was 1.11 g (cm² min)⁻¹. A three-dimensional diffusion-controlled model was used to describe the reduction process, and the mechanism function was 2/3(1 + α)^3/2[(1 + α)^1/3]⁻¹. The values of the reduction reaction rate constant (K) were 12.6 × 10⁻² s⁻¹ and 12.8 × 10⁻² s⁻¹ when the flow rates of H₂ gas were 3 and 4.5 L min⁻¹, respectively. The apparent activation energy was 21.9 kJ mol⁻¹. The empirical equation for the specific reduction rate was calculated as ln r = −2637.5/T − 0.407. Full article

The recycling of spent lithium iron phosphate (LiFePO₄, LFP) batteries is receiving increasing attention as electric-vehicle deployment accelerates worldwide. Pyrometallurgical reduction offers a viable route for large-scale recovery of iron-rich products from spent LFP batteries; however, the resulting Fe-based alloys often retain residual copper (Cu), which deteriorates alloy quality and constrains downstream utilization and refining. In this study, a sulfidation–slag refining process was developed to selectively remove Cu from an Fe–P–Cu alloy produced by dry reduction of spent LFP batteries. FeS was employed as a sulfidizing agent to promote preferential conversion of Cu into sulfide phases, while fayalite (Fe₂SiO₄) slag was introduced to enhance phase separation between metallic and sulfide/slag phases. Thermodynamic calculations coupled with high-temperature experiments were conducted at 1400–1600 °C under various Cu:FeS ratios to identify operating conditions that maximize Cu removal while minimizing Fe loss. The results indicate that Cu is selectively transferred from the metallic phase to Cu–Fe–S sulfide phases, whereas Fe remains predominantly in the metal phase. Under the optimal condition (1400 °C, Cu:FeS = 2:1), the refined metal reached an Fe content of 90.80 wt.%, achieving an Fe recovery of 87.42% and a Cu removal efficiency of 81.13%. The proposed approach provides a practical stepwise refining strategy for upgrading Fe-rich secondary resources recovered from spent LFP batteries and facilitates subsequent impurity-control processes. Full article

The depletion of the mineral resource base is inevitable. Therefore, it is necessary to adapt and expand the resource base by incorporating non-traditional copper sources in production. Slag samples from the Balkhash Copper Smelting Plant (Kazakhstan) were analyzed for phase composition, microstructure, and metal distribution using X-ray diffraction (XRD), scanning electron microscopy (SEM), and chemical and granulometric methods. The slags are characterized by a fayalite structure with a high content of FeO (35–45%) and SiO₂ (25–35%). Sample composition was determined as 0.7–0.8% Cu, 0.39–0.43% Pb, 2.53% Zn, 0.075 g/t Au, and 2.6 g/t Ag. Mineralogical and granulometric analysis revealed a uniform distribution of iron and slag-forming components (SiO₂, Al₂O₃, etc.) across the fractions. In contrast, non-ferrous and precious metals concentrated in the fine classes. Laboratory tests confirmed that the fine dissemination of valuable components led to low efficiency in magnetic and gravity separation, necessitating specific preliminary slag preparation to improve recovery. Flotation tests showed improved recovery, yielding copper concentrates with 4.57% copper content when the material was crushed to 80–90% of the −0.074 mm class. The research creates a basis for the development of environmentally safe and resource-saving technologies and provides initial data for future recovery technologies. Full article

Discarded NdFeB permanent magnets will become a significant source of rare earth elements (REEs) in the future. Electric vehicle (EV) motors utilize 2–5 kg of NdFeB magnets, and researchers are prioritizing the development of suitable extraction technologies. The objective of our research is to separate metal materials (Al, Cu, Fe and FEEs) from EV motors, based on their melting temperatures. REE magnets that pose the greatest challenge are melted together with the electrical steel of the motor, and the potential for extracting REEs in a selective manner from the molten steel was examined based on their significant oxidation potential using FeO–SiO₂ compounds, which act as an oxidizing slag-forming agent, to test the extraction method. Fayalite (2FeO·SiO₂) is the most easily created and ideal eutectic compound for carrying oxygen (FeO) and forming slag (${\mathrm{S}\mathrm{i}\mathrm{O}}_4^{4^{-}}$), typically generated during copper smelting. In this experiment, copper slag was used and the results were compared to a smelting test, which had previously used a synthesized fayalite flux as a model. The smelting test, utilizing synthesized fayalite flux, yielded a 91% Nd recovery rate. The Nd recovery rate in the smelting test with copper slag hit a high of 64.81%, influenced by the smelting’s holding time. The steel contained 0.08% Nd. Iron was recovered from the copper slag at a rate of 73%. During the smelting test, it was observed that the reaction between Nd₂O₃ and the Al₂O₃ crucible resulted in the formation of a layer on the surface of the crucible, diffusion into the crucible itself, and a subsequent reduction in the efficiency of Nd recovery. Full article

The phase transformation of fayalite from copper slag during oxidation roasting was systematically studied in this work with an analysis using X-ray diffraction, X-ray photoelectron spectroscopy, vibrating sample magnetometer, scanning electronic microscope, and energy dispersive spectrometer. The results show that the oxidation of fayalite occurs at ≥300 °C. Fayalite is first oxidized into amorphous Fe₃O₄ and SiO₂ during oxidation roasting. The former then converts into Fe₂O₃ while the latter converts into cristobalite solid solution with increasing temperature. Meanwhile, the specific saturation magnetization of roasted products increases from 9.43 emu/g at 300 °C to 20.66 emu/g at 700 °C, and then decreases to 7.31 emu/g at 1100 °C. The migration of iron in fayalite is prior to that of silicon during oxidation roasting. Therefore, the thickness of the iron oxide layer on the particle surface steadily increases with roasting temperature, from about 1.0 μm at 800 °C to about 5.0 μm at 1100 °C. This study has guiding significance for the iron grain growth in copper slag during the oxidation-reduction roasting process. Full article

This study investigates the effects of sodium sulfate (Na₂SO₄) dosage, reaction temperature, and processing time on the structural decomposition of complex compounds in copper slag. Experimental results demonstrated that applying 20% Na₂SO₄ achieves an impressive decomposition rate of 89%, highlighting its effectiveness in liberating valuable metals from the slag matrix. The optimal temperature for maximizing fayalite decomposition is determined to be 900 °C, which significantly enhances reaction kinetics and efficiency. Furthermore, extending the reaction time to 90 min resulted in the highest observed decomposition efficiency. Subsequent leaching experiments in sulfuric acid confirmed that the liberated metal transitioned into the solution phase was very effective, ensuring high metal recovery rates. The treated samples demonstrated metal recovery rates of 97% for copper (Cu), 96% for iron (Fe), and 93% for zinc (Zn). In contrast, the untreated samples exhibited considerably lower recovery rates, with copper at 61%, iron at 59%, and zinc at 65%. Additionally, this approach mitigates filtration challenges by preventing the formation of silica gel. These findings provide key operational parameters for optimizing metal recovery from copper slag and establish a solid foundation for advancing sustainable and efficient resource extraction research. Full article

The present work is the first study exploring the potential of geopolymer foams based on fayalite slag, an industrial by-product, as the primary precursor, for lightweight and fireproof construction applications. The research involved the synthesis and characterization of geopolymer foams with varying water to solid ratio, followed by testing their physical and mechanical properties. The phase composition and microstructure of the obtained geopolymer foams were examined using powder XRD, Micro-CT and SEM. The geopolymer foams at optimal water to solid ratio (0.15) demonstrated 73.2% relative porosity, 0.92 g/cm³ apparent density and 1.3 MPa compressive strength. The use of an air-entraining admixture improved compressive strength to 2.8 MPa but lowered the relative porosity to 64.5%. Real-size lightweight panel (300 × 300 × 30 mm) specimens were prepared to measure thermal conductivity coefficient (0.243 W/mK) and evaluate size effect and the reaction to direct fire. This study demonstrates the successful preparation of geopolymer foam products containing 81% fayalite slag, highlighting its potential as a lightweight, insulating and fire-resistant material for sustainable construction applications. Full article

Rapid progress in lithium-ion batteries and AI-powered autonomous driving is poised to propel electric vehicles to a 50% share of the global automotive market by the year 2035. Today, there is a major focus on recycling electric vehicle motors, particularly on extracting rare earth elements (REEs) from NdFeB permanent magnets (PMs). This research is based on a single-furnace process concept designed to separate metal components within PM motors by exploiting the varying melting points of the constituent materials, simultaneously extracting REEs present within the PMs and transferring them into the slag phase. Thermodynamic modeling, via Factsage Equilib stream calculations, optimized the experimental process. Simulated materials substituted the PM motor, which optimized modeling-directed melting within an induction furnace. The 2FeO·SiO₂ fayalite flux can oxidize rare earth elements, resulting in slag. The neodymium oxidation reaction by fayalite exhibits a ΔG° of −427 kJ when subjected to an oxygen partial pressure ($P_{O_2}$) of 1.8 × 10⁻⁹, which is lower than that required for FeO decomposition. Concerning the FeO–SiO₂ system, neodymium, in Nd³⁺, exhibits a strong bonding with the ${\mathrm{S}\mathrm{i}\mathrm{O}}_4^{4^{-}}$ matrix, leading to its incorporation within the slag as the silicate compound, Nd₂Si₂O₇. When 30 wt.% fayalite flux was added, the resulting experiment yielded a neodymium extraction degree of 91%, showcasing the effectiveness of this fluxing agent in the extraction process. Full article

The significant volume of copper smelting slags poses environmental challenges, particularly concerning soil and surface water contamination. However, these slags contain valuable elements such as copper and iron, the recovery of which can contribute to both environmental protection and the circular economy in Chile. This study analyzes, at both laboratory and industrial scales, the recovery of copper sulfides from the slags of the Hernán Videla Lira Smelter in Atacama, Chile. Physical, chemical, and mineralogical characterizations were performed, along with flotation tests (rougher and cleaner) to optimize the grinding degree, pH, reagents, and flotation times. The slag, with a copper grade of 0.71%, contains fayalite, magnetite, quartz, pyrite, and chalcopyrite. In the laboratory, the concentrate obtained in the rougher stage showed a copper grade of 3.7% with a recovery rate of 62.1%; in the cleaner stage, the grade increased to 24.4%, with a recovery rate of 71.7%. At the industrial level, the rougher–cleaner circuit produced concentrates with a copper grade of 27.9% and a recovery rate of 87.5% processing 1344 tons per day, thus demonstrating the viability of this methodology. Full article

The objects of the study were converter slags from the Balkhash copper plant in their initial state and after heat treatment. Using mineralogical and X-ray phase analysis, scanning electron microscopy (SEM), and electron probe microanalysis (EPMA), it was found that the initial converter slag and its thermally treated samples have identical matrices with almost complete coincidence in mineral and phase compositions. The distinguishing feature is the quantitative ratio of mineral components in the slag mass. Almost all of the iron is oxidized and present in the form of fayalite, magnetite, and magnetite, with other elements (silicon, copper, zinc, and aluminum) incorporated into its lattice. The structure of all slag samples indicates an association of sulfur exclusively with copper. Copper in the slags was identified in both metallic and sulfide forms. Slow cooling of the converter slag after its remelting contributes to the reduction in the sulfide–metal suspension in the volume of the melt and its coarsening. During slow cooling, structural changes occur not only in the main oxide part of the slag but also in the polymetallic globules. Full article

This paper gives an overview of findings, connected with metallurgical activity, at the Pržanj archeological site near Ljubljana, Slovenia. More than 230 kg of slag and other remains connected with early medieval (from the 5th to the 12th century AD) metallurgical activities was found at the excavation site. The remains were grouped into four categories, i.e., furnace remains, ore, slag and a ferrous product, and analyzed in detail to obtain their chemical composition, microstructural characteristics, and mineral phase composition. The furnace wall remains, identified by their morphology and chemical composition, revealed an intensive iron processing activity at the site. The iron ore at the site was identified as goethite (FeO(OH)), a surprising find in Slovenia where limonite is typically used, and its presence suggests the potential exploitation of local bog iron ore, given the site’s geological context. Abundant slag remains at the site, identified by their shape, molten microstructure, and mineral components like wuestite, fayalite, and hercynite, indicated sophisticated smelting practices, including the use of CaO-rich materials to lower the melting temperature, a technique likely preserved from antiquity. Findings of ferrous products at ancient metallurgical sites are rare due to their value, but the discovery of a corroded iron bloom conglomerate at this site, initially mistaken for furnace remains, highlights the challenges in identifying small, corroded ferrous fragments that are often misidentified as ore. The results indicate extensive metallurgical activity at the excavation site, marking it as the first documented early medieval iron smelting production site in Slovenia. Full article

The treatment of large amounts of copper slag is an unavoidable issue resulting from the high demand for copper during the global transition to a sustainable development path. Metal-rich copper slag might serve as a potential source of metals through secondary recovery. In this study, two copper slags (CS1 and CS2) with different metallurgical properties were characterized, focusing on secondary metal recovery. The X-ray diffraction (XRD) results show that fayalite (Fe₂SiO₄) and magnetite (Fe₃O₄) were the main crystalline phases in both CS1 and CS2. In addition, CS2 exhibited a more stable amorphous silicate network than CS1, which was attributed to the differences in the content of Si-O-3NBO linkages. The sequential extraction of Zn, Cu, Fe, and Pb from the slags was also explored, with the Cu content in CS1 being substantially lower than that in CS2. All metals were distributed in the F5 residue fraction. Cu was the most mobile metal as a result of the large proportion of soluble fractions (F1–F3), followed by Zn and Fe. This study explored the chemical speciation of Zn, Cu, Fe, and Pb from copper slags, which has practical implications for secondary metal recovery from such materials. Full article