Search Results (21)

Microlens arrays (MLAs) are essential for light collection, extraction, and high-resolution imaging. However, most reported MLAs have a limited filling factor. Here, we demonstrate MLAs using three different UV-curing optical adhesives based on the electrohydrodynamic inkjet (E-jet) printing technique. The highest filling factor of 89.91% is achieved. By controlling the curvature of the microlens via the surface treatment of the substrate, a series of MLAs with different numerical apertures can be obtained. With the high-consistency printing technique, the demonstrated high filling factor MLAs could be potentially useful to improve the performance of optical imaging and sensing systems. Full article

Green sustainable solvents have emerged as promising alternatives to petroleum-derived options, such as toluene. This study demonstrates the use of cyrene as an effective exfoliation medium for graphene nanoplatelets (GNPs) and hexagonal boron nitride (hBN) and molybdenum disulfide (MoS₂) particles. The incorporation of polyvinylpyrrolidone (PVP) attenuates the shear-thinning behavior of GNP and hBN suspensions, maintaining a constant shear viscosity over a wide range of shear rates regardless of PVP molecular weight. Despite the presence of polymer, elasticity is hindered by inertia effects, making it impossible to accurately measure the extensional relaxation time in the capillary breakup extensional rheometer (CaBER). Assuming the weak elasticity of the formulations has a negligible impact on the breakup mechanism, we estimated droplet sizes for drop-on-demand (DoD) inkjet printing and electrohydrodynamic (EHD) jet printing based on fluid properties, i.e., viscosity, surface tension and density, and nozzle inner diameter ($D_{nozzle}$). Results indicate that the droplet size ratio ($D_{drop}/D_{nozzle}$) in DoD printing can be up to two orders of magnitude higher than the one predicted for EHD jet printing at the same flow rate. This work highlights the potential of cyrene-based 2D inks as eco-friendly alternatives for advanced printing technologies. Full article

Droplet quality in drop-on-demand (DoD) Electrohydrodynamic (EHD) inkjet printing plays a crucial role in influencing the overall performance and manufacturing quality of the operation. The current approach to droplet printing analysis involves manually outlining/labeling the printed dots on the substrate under a microscope and then using microscope software to estimate the dot sizes by assuming the dots have a standard circular shape. Therefore, it is prone to errors. Moreover, the dot spacing information is missing, which is also important for EHD DoD printing processes, such as manufacturing micro-arrays. In order to address these issues, the paper explores the application of feature extraction methods aimed at identifying characteristics of the printed droplets to enhance the detection, evaluation, and delineation of significant structures and edges in printed images. The proposed method involves three main stages: (1) image pre-processing, where edge detection techniques such as Canny filtering are applied for printed dot boundary detection; (2) contour detection, which is used to accurately quantify the dot sizes (such as dot perimeter and area); and (3) centroid detection and distance calculation, where the spacing between neighboring dots is quantified as the Euclidean distance of the dot geometric centers. These stages collectively improve the precision and efficiency of EHD DoD printing analysis in terms of dot size and spacing. Edge and contour detection strategies are implemented to minimize edge discrepancies and accurately delineate droplet perimeters for quality analysis, enhancing measurement precision. The proposed image processing approach was first tested using simulated EHD printed droplet arrays with specified dot sizes and spacing, and the achieved quantification accuracy was over 98% in analyzing dot size and spacing, highlighting the high precision of the proposed approach. This approach was further demonstrated through dot analysis of experimentally EHD-printed droplets, showing its superiority over conventional microscope-based measurements. Full article

Flexible devices have extensive applications in areas including wearable sensors, healthcare, smart packaging, energy, automotive and aerospace sectors, and other related fields. Droplet printing technology can be utilized to print flexible electronic components with micro/nanostructures on various scales, exhibiting good compatibility and wide material applicability for device production. This paper provides a comprehensive review of the current research status of droplet printing technologies and their applications across various domains, aiming to offer a valuable reference for researchers in related areas. Full article

Current methods for thin film sensors preparation include screen printing, inkjet printing, and MEMS (microelectromechanical systems) techniques. However, their limitations in achieving sub-10 μm line widths hinder high-density sensors array fabrication. Electrohydrodynamic (EHD) printing is a promising alternative due to its ability to print multiple materials and multilayer structures with patterned films less than 10 μm width. In this paper, we innovatively proposed a method using only EHD printing to prepare ultra-micro thin film temperature sensors array. The sensitive layer of the four sensors was compactly integrated within an area measuring 450 μm × 450 μm, featuring a line width of less than 10 μm, and a film thickness ranging from 150 nm to 230 nm. The conductive network of silver nanoparticles exhibited a porosity of 0.86%. After a 17 h temperature-resistance test, significant differences in the performance of the four sensors were observed. Sensor 3 showcased relatively superior performance, boasting a fitted linearity of 0.99994 and a TCR of 937.8 ppm/°C within the temperature range of 20 °C to 120 °C. Moreover, after the 17 h test, a resistance change rate of 0.17% was recorded at 20 °C. Full article

Cracks have a primary effect on the failure of a structure. Therefore, the development of crack sensors with high accuracy and resolution and cracks detection method are important. In this study, the crack sensors were fabricated, and the crack locations were detected with the electrical signal of the crack sensor. First, a metal grid-type micro-crack sensor based on silver was fabricated. The sensor is made with electrohydrodynamics (EHD) inkjet printing technology, which is well known as the next generation of printed electronics technology. Optimal printing conditions were established through experiments, and a grid sensor was obtained. After that, single cracks and multiple cracks were simulated on the sensor, and electrical signals generated from the sensor were measured. The measured electrical signal tracked the location of the cracks in three steps: simple cross-calculation, interpolation, and modified P-SPICE. It was confirmed that cracks could be effectively found and displayed using the method presented in this paper. Full article

To use Ag nanowires for various industries, it is crucial to develop an appropriate patterning method. There are various types of patterning methods, but there has been no comprehensive review discussing and summarizing them. This review paper provides an overview of the various patterning techniques of Ag nanowire electrodes, including photolithography, nanoimprint lithography, inkjet printing, electrohydrodynamic jet printing, and other emerging methods. These transparent electrodes have received significant attention due to their high transparency, low sheet resistance, and flexibility, making them ideal for applications such as flexible electronics, touch screens, and solar cells. Each patterning technique has its benefits and limitations, and its suitability depends on specific application requirements. Photolithography is a well-established technique that can achieve high-resolution patterns, while nanoimprint lithography is a low-cost and versatile method for large-area patterning. Inkjet printing and E-jet printing provide the advantages of high throughput, precise control, and the ability to print on different substrates. Stencil printing, laser direct writing, and electrospinning are emerging techniques that showing high potential for patterning Ag nanowire electrodes. The choice of patterning technique ultimately depends on various factors, such as resolution requirements, cost, substrate compatibility, and throughput. Full article

Metal halide perovskite quantum dots (PQDs) are widely used in the display field due to their excellent photoelectric properties, such as ultra-narrow half-peak widths and ultra-pure luminescence color purity. Inkjet printing, laser direct writing and electrospinning are all common methods for PQDs printing to prepare micropattern displays. In order to produce large-scale and high-resolution PQDs micropatterns, electrohydrodynamic (EHD) printing technology is capable of large-scale deposition of highly oriented nanofibers on rigid or pliable, flat or bent substrates with the advantages of real-time regulation and single control. Therefore, it has a lot of potential in the fabrication of pliable electronic devices for one-dimensional ordered light-emitting fibers. Polycaprolactone (PCL) as an EHD printing technology polymer material has the advantages of superior biocompatibility, a low melting point, saving energy and easy degradation. By synthesizing CsPbBr₃ quantum dots (QDs) and PCL composite spinning stock solution, we used the self-built EHD printing platform to prepare the PCL@CsPbBr₃ composite light-emitting optical fiber and realized the flexible display of high-resolution micropatterns in polydimethylsiloxane (PDMS) packaging. An x-ray diffractometer (XRD), scanning electron microscope (SEM) and photoluminescence (PL) were used to characterize and analyze the fiber’s morphology, phase and spectral characteristics. EHD printing technology may open up interesting possibilities for flexible display applications based on metal halide PQDs. Full article

Electrohydrodynamic (EHD) jet printing is known as a versatile method to print a wide viscosity range of materials that are impossible to print by conventional inkjet printing. Hence, with the understanding of the benefits of EHD jet printing, solution-based MoS₂ and a high-viscosity Ag paste were EHD jet-printed for electronic applications in this work. In particular, printed MoS₂ TFTs with a patterned Ag source and drain were successfully fabricated with low-k silica (SiO₂) and high-k alumina (Al₂O₃) gate dielectrics, respectively. Eventually, the devices based on Al₂O₃ exhibited much better electrical properties compared to the ones based on SiO₂. Interestingly, an improvement of around one order of magnitude in hysteresis was achieved for devices after changing the gate insulator from SiO₂ to Al₂O₃. In effect, the results of this work for the printed MoS₂ and the printed Ag source and drains for TFTs demonstrate a new approach for jet printing in the fabrication of electronic devices. Full article

Electrohydrodynamic (EHD) inkjet printing is an efficient technique for printing multiple sensors in a multifaceted area. It can be applied to various fields according to the shape of the printing result and the algorithm employed. In this study, temperature sensors capable of detecting heat sources were fabricated. Inks suitable for EHD inkjet printing were produced, and optimal parameters for printing were determined. Printing was performed using the corresponding parameters, and various printing results were obtained. Furthermore, an experiment was conducted to confirm the temperature measurement characteristics of the results and the tolerance of the sensor. Grid-type sensors were fabricated based on the results, and the sensor characteristics were confirmed in an orthogonal form. Heat was applied to arbitrary positions. Resistance to changes due to heat was measured, and the location at which the heat was generated was detected by varying the change in resistance. Through this study, efficient heat control can be achieved, as the location of the heat source can be identified quickly. Full article

In the field of soft electronics, high-resolution and transparent structures based on various flexible materials constructed via various printing techniques are gaining attention. With the support of electrical stress-induced conductive inks, the electrohydrodynamic (EHD) jet printing technique enables us to build high-resolution structures compared with conventional inkjet printing techniques. Here, EHD jet printing was used to fabricate a high-resolution, transparent, and flexible strain sensor using a polydimethylsiloxane (PDMS)/xylene elastomer, where repetitive and controllable high-resolution printed mesh structures were obtained. The parametric effects of voltage, flow rate, nozzle distance from the substrate, and speed were experimentally investigated to achieve a high-resolution (5 µm) printed mesh structure. Plasma treatment was performed to enhance the adhesion between the AgNWs and the elastomer structure. The plasma-treated functional structure exhibited stable and long strain-sensing cycles during stretching and bending. This simple printing technique resulted in high-resolution, transparent, flexible, and stable strain sensing. The gauge factor of the strain sensor was significantly increased, owing to the high resolution and sensitivity of the printed mesh structures, demonstrating that EHD technology can be applied to high-resolution microchannels, 3D printing, and electronic devices. Full article

EHD printing is an advanced deposition technology that is commonly utilized for the direct manufacture of electrical devices. In this study, meander-type resistive electrodes consisting of silver nanoparticles were printed directly on rigid glass and flexible polyethylene terephthalate (PET) substrates. High-resolution patterns of ≈50 µm linewidth were successfully printed on untreated surfaces utilizing a bigger nozzle of 100 µm inner diameter after improving the experimental settings. The manufactured electrodes were evaluated and used as Resistance Temperature Detectors (RTDs) and micro-heaters in a systematic manner. The temperature sensors performed well, with a Temperature Coefficient of Resistivity (TCRs) of 11.5 $\times {10}^{-3}/°\mathrm{C}$ and 13.3 $\times {10}^{-3}/°\mathrm{C}$, for glass and PET substrates, respectively, throughout a wide temperature range of 100 °C and 90 °C. Furthermore, the RTDs had a quick response and recovery time, as well as minimal hysteresis. The electrodes’ measured sensitivities as micro-heaters were 3.3 °C/V for glass and 6.8 °C/V for PET substrates, respectively. The RTDs were utilized for signal conditioning in a Wheatstone bridge circuit with a self-heating temperature of less than 1 °C as a practical demonstration. The micro-heaters have a lot of potential in the field of soft wearable electronics for biomedical applications, while the extremely sensitive RTDs have a lot of potential in industrial situations for temperature monitoring. Full article

Three dimensional printing (3DP), or additive manufacturing, is an exponentially growing process in the fabrication of various technologies with applications in sectors such as electronics, biomedical, pharmaceutical and tissue engineering. Micro and nano scale printing is encouraging the innovation of the aforementioned sectors, due to the ability to control design, material and chemical properties at a highly precise level, which is advantageous in creating a high surface area to volume ratio and altering the overall products’ mechanical and physical properties. In this review, micro/-nano printing technology, mainly related to lithography, inkjet and electrohydrodynamic (EHD) printing and their biomedical and electronic applications will be discussed. The current limitations to micro/-nano printing methods will be examined, covering the difficulty in achieving controlled structures at the miniscule micro and nano scale required for specific applications. Full article

Temperature measurement is very important for thermal control, which is required for the advancement of mechanical and electronic devices. However, current temperature sensors are limited by their inability to measure curved surfaces. To overcome this problem, several methods for printing flexible substrates were proposed. Among them, electrohydrodynamic (EHD) inkjet printing technology was adopted because it has the highest resolution. Since EHD inkjet printing technology is limited by the type of ink used, an ink with temperature-sensing properties was manufactured for use in this printer. To confirm the applicability of the prepared ink, its resistance characteristics were investigated, and the arrangement and characteristics of the particles were observed. Then, the ink was printed using the EHD inkjet approach. In addition, studies of the meniscus shapes and line widths of the printed results under various conditions confirmed the applicability of the ink to the EHD inkjet printing technology and the change in its resistance with temperature. Full article

This review focuses on the current state of the art in liquid metal additive manufacturing (AM), an emerging and growing family of related printing technologies used to fabricate near-net shape or fully free-standing metal objects. The various printing modes and droplet generation techniques as applied to liquid metals are discussed. Two different printing modes, continuous and drop-on-demand (DOD), exist for liquid metal printing and are based on commercial inkjet printing technology. Several techniques are in various stages of development from laboratory testing, prototyping, to full commercialization. Printing techniques include metal droplet generation by piezoelectric actuation or impact-driven, electrostatic, pneumatic, electrohydrodynamic (EHD), magnetohydrodynamic (MHD) ejection, or droplet generation by application of a high-power laser. The impetus for development of liquid metal printing was the precise, and often small scale, jetting of solder alloys for microelectronics applications. The fabrication of higher-melting-point metals and alloys and the printing of free-standing metal objects has provided further motivation for the research and development of liquid metal printing. Full article