Search Results (87)

Soybean (Glycine max (L.) Merrill) is highly sensitive to water deficit, particularly during the vegetative phase, when morphological and metabolic plasticity support continued growth and photosynthetic efficiency. We applied eleven water regimes, from full irrigation (W100) to total water withholding (W0), to plants grown under controlled conditions. After 14 days, we quantified morphophysiological, biochemical, leaf optical, gas exchange, and chlorophyll a fluorescence traits. Drought induces significant reductions in leaf area, biomass, pigment pools, and photosynthetic rates (A, g_s, ΦPSII) while increasing the levels of oxidative stress markers (electrolyte leakage, ROS) and proline accumulation. OJIP transients and JIP test metrics revealed reduced electron-transport efficiency and increased energy dissipation for many parameters under severe stress. Principal component analysis (PCA) clearly separated those treatments. PC1 captured growth and water status variation, whereas PC2 reflected photoprotective adjustments. These data show that progressive drought limits carbon assimilation via coordinated diffusive and biochemical constraints and that the accumulation of proline, phenolics, and lignin is associated with osmotic adjustment, antioxidant buffering, and cell wall reinforcement under stress. The combined use of hyperspectral sensors, gas exchange, chlorophyll fluorescence, and multivariate analyses for phenotyping offers a rapid, nondestructive diagnostic tool for assessing drought severity and the possibility of selecting drought-resistant genotypes and phenotypes in a changing stress environment. Full article

Receptor-like kinases (RLKs) are instrumental in regulating plant cell surface sensing and vascular tissue differentiation. Wall-associated kinases (WAKs) are a unique group of RLKs that have been identified as key cell wall integrity (CWI) sensors. WAK signaling is suggested to be activated during growth in response to cell expansion or when the cell wall is damaged, for example, during pathogen attack. WAKs are proposed to interact with pectins or pectin fragments that are enriched in primary walls. Secondary walls have low levels of pectins, yet recent studies have shown important functions of WAKs during secondary wall development. Several wak mutants show defects in secondary wall thickening of the xylem vessels and fibers or the development of vascular bundles. This review will discuss the recent advances in our understanding of WAK functions during plant development and responses to abiotic stresses and the regulation of vascular tissue secondary wall development. Full article

The disinfection of drinking water is essential for eliminating pathogens and preventing waterborne diseases. However, this process generates various disinfection byproducts (DBPs), which toxicological research indicates can have detrimental effects on living organisms. Moreover, the safety of these DBPs has not been sufficiently assessed, underscoring the need for a comprehensive evaluation of their toxic effects and associated health risks. Compared to traditional methods for studying the toxicity of pollutants, emerging electrochemical sensing technologies offer advantages such as simplicity, speed, and sensitivity, presenting an effective means for toxicity research on pollutants. However, challenges remain in this field, including the need to improve electrode sensitivity and reduce electrode costs. In this study, a pencil graphite electrode (PGE) was modified with carboxylated multi-walled carbon nanotubes (MWCNT-COOH) and nano-iron (III) oxide (α-Fe₂O₃) to fabricate a low-cost electrode with excellent electrocatalytic performance for cell-active substances. Subsequently, a novel cellular electrochemical sensor was constructed for the sensitive detection of the toxicity of three drinking water DBPs. The half inhibitory concentration (IC₅₀) values of 2-chlorophenylacetonitrile (2-CPAN), 3-chlorophenylacetonitrile (3-CPAN), and 4-chlorophenylacetonitrile (4-CPAN) for HepG2 cells were 660.69, 831.76, and 812.83 µM, respectively. This study provides technical support and scientific evidence for the toxicity detection and safety assessment of emerging contaminants. Full article

Ustilago esculenta is a dimorphic fungus that specifically infects Zizania latifolia, causing stem swelling and the formation of an edible fleshy stem known as jiaobai. The pathogenicity of U. esculenta is closely associated with the development of jiaobai and phenotypic differentiation. Msb2 acts as a key upstream sensor in the MAPK (mitogen-activated protein kinase) signaling pathway, playing critical roles in fungal hyphal growth, osmotic regulation, maintenance of cell wall integrity, temperature adaptation, and pathogenicity. In this study, we cloned the UeMsb2 gene from U. esculenta (GenBank No. MW768949). The open reading frame of UeMsb2 is 3015 bp in length, lacks introns, encodes a 1004-amino-acid protein with a conserved serine-rich domain, and is localized to the vacuole. Expression analysis revealed that UeMsb2 is inducibly expressed during both hyphal growth and infection processes. Deletion of UeMsb2 did not affect haploid morphology or growth rate in vitro but significantly impaired the strain’s mating ability, suppressed filamentous growth, slowed host infection progression, and downregulated the expression of b signaling pathway genes associated with pathogenicity. Notably, the deletion of UeMsb2 did not influence the in vitro growth of U. esculenta under hyperosmotic, thermal, or oxidative stress conditions. These findings underscore the critical role of UeMsb2 in regulating the pathogenicity of U. esculenta. This study provides insights into the interaction between U. esculenta and Z. latifolia, particularly the mechanisms that drive host stem swelling. Full article

In recent years, the rapid alkalinization factor (RALF) family of cysteine-rich peptides has been reported to be crucial for several plant signaling mechanisms, including cell growth, plant immunity and fertilization. RALF4 and RALF19 (RALF4/19) pollen peptides redundantly regulate the pollen tube integrity and growth through binding to their receptors ANXUR1/2 (ANX1/2) and Buddha’s Paper Seal 1 and 2 (BUPS1/2), members of the Catharanthus roseus RLK1-like (CrRLK1L) family, and, thus, are essential for plant fertilization. However, the signaling mechanisms at the cellular level that follow these binding events remain unclear. In this study, we show that the addition of synthetic peptide RALF4 rapidly halts pollen tube growth along with the excessive deposition of plasma membrane and cell wall material at the tip. The ratiometric imaging of genetically encoded ROS and Ca²⁺ sensors-expressing pollen tubes shows that RALF4 treatment modulates the cytoplasmic levels of reactive oxygen species (ROS) and calcium (Ca²⁺) in opposite ways at the tip. Thus, we propose that pollen RALF4/19 peptides bind ANX1/2 and BUPS1/2 to regulate ROS and calcium homeostasis to ensure proper cell wall integrity and control of pollen tube growth. Full article

Carboxymethyl cellulose (CMC) was prepared from sugarcane bagasse (SB) in minutes using a novel microwave method. Additionally, nitrogen-doped carbon dots (N–CDs) were synthesized from SB using the same microwave technique. These materials were crosslinked with CaCl₂ to prepare antibacterial/antifungal hydrogel sensors. In this regard, both CMC@Ca and CMC@Ca-N–CDs exhibited antibacterial activity against Escherichia coli (Gram negative), while only CMC@Ca-N–CDs demonstrated antibacterial activity against Staphylococcus aureus (Gram positive). Moreover, both materials showed antifungal activity against Candida albicans. The molecular docking study demonstrated that CMC@Ca-N–CDs showed good binding with proteins with short bond length 2.59, 2.80, and 1.97 A° for Escherichia coli, Staphylococcus aureus, and Candida albicans, respectively. These binding affinities were corroborated by the observed inhibition zone diameters. Furthermore, fluorescence microscope revealed distinct imaging patterns between Gram-positive and Gram-negative bacteria, as well as pathogenic yeast (fungi). CMC@Ca-N–CDs emitted blue light when exposed to Escherichia coli and Candida albicans (i.e., CMC@Ca-N–CDs/Escherichia coli and Candida albicans), whereas it emitted bright-red light when exposed to Staphylococcus aureus (i.e., CMC@Ca-N–CDs/Staphylococcus aureus). This disparity in the fluorescence-emitted colors is due to the difference in the cell wall of these microorganisms. Additionally, DFT calculations were conducted to substantiate the robust chemical interactions between CMC, Ca²⁺, and N–CDs. Full article

The development of ISE-based sensors for the analysis of nitrates in liquid phase is described in this work. Focusing on the tetradodecylammonium nitrate (TDDAN) ion exchanger as well as on fluoropolysiloxane (FPSX) polymer-based layers, electrodeposited matrixes containing double-walled carbon nanotubes (DWCNTs), embedded in either polyethylenedioxythiophene (PEDOT) or polypyrrole (PPy) polymers, ensured improved ion-to-electron transducing layers for NO₃⁻ detection. Thus, FPSX-based pNO₃-ElecCell microsensors exhibited good detection properties (sensitivity up to 55 mV/pX for NO₃ values ranging from 1 to 5) and acceptable selectivity in the presence of the main interferent anions (Cl⁻, HCO₃⁻, and SO₄²⁻). Focusing on the temporal drift bottleneck, mixed results were obtained. On the one hand, relatively stable measurements and low temporal drifts (~1.5 mV/day) were evidenced on several days. On the other hand, the pNO₃ sensor properties were degraded in the long term, being finally characterized by high response times, low detection sensitivities, and important measurement instabilities. These phenomena were related to the formation of some thin water-based layers at the polymer–metal interface, as well as the physicochemical properties of the TDDAN ion exchanger in the FPSX matrix. However, the improvements obtained thanks to DWCNT-based ion-to-electron transducing layers pave the way for the long-term analysis of NO₃⁻ ions in real water-based solutions. Full article

Singlet oxygen (¹O₂) is known to have antibacterial activity; however, production can involve complex processes with expensive chemical precursors and/or significant energy input. Recent studies have confirmed the generation of ¹O₂ through the activation of photosensitizer molecules (PSs) with visible light in the presence of oxygen. Given the increase in the incidence of foodborne diseases associated with cross-contamination in food-processing industries, which is becoming a major concern, food-safe additives, such as chlorophyllins, have been studied for their ability to act as PSs. The fluorescent probe Singlet Oxygen Sensor Green (SOSG^®) was used to estimate ¹O₂ formation upon the irradiation of traditional PSs (rose bengal (RB), chlorin 6 (ce6)) and novel chlorophyllins, sodium magnesium (NaChl) and sodium copper (NaCuChl), with both simulated-solar and visible light. NaChl gave rise to a similar ¹O₂ production rate when compared to RB and ce6. Basic mixing was shown to introduce sufficient oxygen to the PS solutions, preventing the limitation of the ¹O₂ production rate. The NaChl-based inactivation of Gram-positive S. aureus and Gram-negative E. coli was demonstrated with a 5-log reduction with UV–Vis light. The NaChl-based inactivation of Gram-positive S. aureus was accomplished with a 2-log reduction after 105 min of visible-light irradiation and a 3-log reduction following 150 min of exposure from an initial viable bacterial concentration of 10⁶ CFU mL⁻¹. CHS-NaChl-based photosensitization under visible light enhanced Gram-negative E. coli inactivation and provided a strong bacteriostatic effect preventing E. coli proliferation. The difference in the ability of NaChl and CHS-NaChl complexes to inactivate Gram-positive and Gram-negative bacteria was confirmed to result from the cell wall structure, which impacted PS–bacteria attachment and therefore the production of localized singlet oxygen. Full article

Simple and reliable electrochemical sensors are highly demanded in medicine and pharmacy for the fast determination of metabolites and biomarkers of diseases. In this work, a flow-through biosensor system was developed on the base of a screen-printed carbon electrode modified with pillar[3]arene[2]quinone and ferrocene implemented in carbon black. The modification was performed in a single step and resulted in the formation of a stable layer with good operation characteristics. Uricase was immobilized on the inner walls of a replaceable reactor by carbodiimide binding. A flow-through cell was manufactured by 3D printing from poly(lactic acid). The flow-through system was first optimized on the hydrogen peroxide assay and then used for the determination of 1 nM–0.1 mM uric acid (limit of detection 0.3 nM, 20 measurements per hour). Implementation of ferrocene resulted in a synergetic increase in the cathodic current of H₂O₂ reduction measured by flow switching in chronoamperometric mode. The developed system was tested on the determination of uric acid in artificial urine and Ringer–Locke solution and showed a recovery rate of 96–112%. In addition, the possibility of determination of H₂O₂ in commercial disinfectants was shown. Easy assembly, fast and reliable signal and low consumption of the reagents make the system developed attractive for routine clinical analysis of metabolites. Full article

The technology to jet print metal lines with precise shape fidelity on diverse substrates is gaining higher interest across multiple research fields. It finds applications in additively manufactured flexible electronics, environmentally friendly and sustainable electronics, sensor devices for medical applications, and fabricating electrodes for solar cells. This paper provides an experimental investigation to deepen insights into the non-contact printing of solder lines using StarJet technology, eliminating the need for surface activation, substrate heating, curing, or post-processing. Moreover, it employs bulk metal instead of conventional inks or pastes, leading to cost-effective production and enhanced conductivity. The effect of molten metal temperature, substrate temperature, standoff distance, and printing velocity was investigated on polymer foils (i.e., PET sheets). Robust printing parameters were derived to print uniform, bulge-free, bulk metal lines suitable for additive manufacturing applications. The applicability of the derived parameters was extended to 3D-printed PLA, TPU, PA-GF, and PETG substrates having a much higher surface roughness. Additionally, a high aspect ratio of approx. 16:1 wall structure has been demonstrated by printing multiple metal lines on top of each other. While challenges persist, this study contributes to advancing additively manufactured electronic devices, highlighting the capabilities of StarJet metal jet-printing technology. Full article

Hydrogen peroxide (H₂O₂) is a signaling molecule that has the capacity to control a variety of biological processes in organisms. Cancer cells release more H₂O₂ during abnormal tumor growth. There has been a considerable amount of interest in utilizing H₂O₂ as a biomarker for the diagnosis of cancer tissue. In this study, an electrochemical sensor for H₂O₂ was constructed based on 3D reduced graphene oxide (rGO), MXene (Ti₃C₂), and multi-walled carbon nanotubes (MWCNTs) composite. Three-dimensional (3D) rGO–Ti₃C₂–MWCNTs sensor showed good linearity for H₂O₂ in the ranges of 1–60 μM and 60 μM–9.77 mM at a working potential of −0.25 V, with sensitivities of 235.2 µA mM⁻¹ cm⁻² and 103.8 µA mM⁻¹ cm⁻², respectively, and a detection limit of 0.3 µM (S/N = 3). The sensor exhibited long-term stability, good repeatability, and outstanding immunity to interference. In addition, the modified electrode was employed to detect real-time H₂O₂ release from cancer cells and cancer tissue ex vivo. Full article

This study investigated how welding affects the thermal deformation of square cells produced for casks, which are dry storage containers for spent nuclear fuel. We aimed to minimize structural deformation by utilizing STS316L as the material for the square cells. We explored a method of subdividing the square cells and joining them through butt welding. Keeping the upper plate thickness constant, GTA butt welding was conducted while varying the column’s wall thickness, followed by measurement with a laser vision sensor. The heat conduction and thermal strain were then calculated using a finite element analysis (FEM). Both experimental and analytical results confirmed that there was significant thermal deformation in the cases of thick-walled columns due to variations in heat conduction distribution, with the resulting deformation patterns depending on thickness. Full article

Three-dimensional flexible piezoresistive porous sensors are of interest in health diagnosis and wearable devices. In this study, conductive porous sensors with complex triply periodic minimal surface (TPMS) structures were fabricated using the 3D printed sacrificial mold and enhancement of MWCNTs. A new curing routine by the self-resistance electric heating was implemented. The porous sensors were designed with different pore sizes and unit cell types of the TPMS (Diamond (D), Gyroid (G), and I-WP (I)). The impact of pore characteristics and the hybrid fabrication technique on the compressive properties and piezoresistive response of the developed porous sensors was studied. The results indicate that the porous sensors cured by the self-resistance electric heating could render a uniform temperature distribution in the composites and reduce the voids in the walls, exhibiting a higher elastic modulus and a better piezoresistive response. Among these specimens, the specimen with the D-based structure cured by self-resistance electric heating showed the highest responsive strain (61%), with a corresponding resistance response value of 0.97, which increased by 10.26% compared to the specimen heated by the external heat sources. This study provides a new perspective on design and fabrication of porous materials with piezoresistive functionalities, particularly in the realm of flexible and portable piezoresistive sensors. Full article

Confronting the challenge of biofilm resistance and widespread antimicrobial resistance (AMR), this study emphasizes the need for innovative monitoring methods and explores the potential of bacteriophages against bacterial biofilms. Traditional methods, like optical density (OD) measurements and confocal microscopy, crucial in studying biofilm–virus interactions, often lack real-time monitoring and early detection capabilities, especially for biofilm formation and low bacterial concentrations. Addressing these gaps, we developed a new real-time, label-free radiofrequency sensor for monitoring bacteria and biofilm growth. The sensor, an open-ended coaxial probe, offers enhanced monitoring of bacterial development stages. Tested on a biological model of bacteria and bacteriophages, our results indicate the limitations of traditional OD measurements, influenced by factors like sedimented cell fragments and biofilm formation on well walls. While confocal microscopy provides detailed 3D biofilm architecture, its real-time monitoring application is limited. Our novel approach using radio frequency measurements (300 MHz) overcomes these shortcomings. It facilitates a finer analysis of the dynamic interaction between bacterial populations and phages, detecting real-time subtle changes. This method reveals distinct phases and breakpoints in biofilm formation and virion interaction not captured by conventional techniques. This study underscores the sensor’s potential in detecting irregular viral activity and assessing the efficacy of anti-biofilm treatments, contributing significantly to the understanding of biofilm dynamics. This research is vital in developing effective monitoring tools, guiding therapeutic strategies, and combating AMR. Full article

Electrolysis stands as a pivotal method for environmentally sustainable hydrogen production. However, the formation of gas bubbles during the electrolysis process poses significant challenges by impeding the electrochemical reactions, diminishing cell efficiency, and dramatically increasing energy consumption. Furthermore, the inherent difficulty in detecting these bubbles arises from the non-transparency of the wall of electrolysis cells. Additionally, these gas bubbles induce alterations in the conductivity of the electrolyte, leading to corresponding fluctuations in the magnetic flux density outside of the electrolysis cell, which can be measured by externally placed magnetic sensors. By solving the inverse problem of the Biot–Savart Law, we can estimate the conductivity distribution as well as the void fraction within the cell. In this work, we study different approaches to solve the inverse problem including Invertible Neural Networks (INNs) and Tikhonov regularization. Our experiments demonstrate that INNs are much more robust to solving the inverse problem than Tikhonov regularization when the level of noise in the magnetic flux density measurements is not known or changes over space and time. Full article