Search Results (89)

As one of the important lithium resource sources, lepidolite has become a new energy strategic resource research hot spot. The efficient flotation of lepidolite directly affects the recovery and economic value of lithium resources. This paper systematically reviews the flotation research progress of lepidolite, focusing on the influence of the type of capture agent and process parameters (pH, activator, and depressant) on flotation. In view of the separation problems caused by the similarity of the surface properties of lepidolite and its associated gangue minerals (albite, feldspar, and quartz), the strategies for regulating the crystal structure of the minerals and their surface properties are analyzed. In addition, the lepidolite flotation process and its challenges are summarized, including poor selectivity of chemicals, fine mineral embedded size, easy to form sludge, and insufficient environmental friendliness, etc. The future development direction of lepidolite flotation technology is also prospected, which provides theoretical support and reference for the efficient recovery of lepidolite. Full article

The design of small-molecule inhibitors targeting proprotein convertase subtilisin/Kein type 9 (PCSK9) remains a forefront challenge in combating atherosclerosis. While various monoclonal antibodies have achieved clinical success, small-molecule inhibitors are hindered by the unique structural features of the PCSK9 binding interface. In this study, a potential small-molecule inhibitor was identified through virtual screening, followed by molecular dynamics (MD) simulations to explore the binding mechanisms between the inhibitor and the PCSK9 protein. Binding free energies were calculated using molecular mechanics/Generalized Born surface area (MM/GBSA) with the interaction entropy (IE) method, and critical hot-spot residues were identified via alanine scanning analysis. Key residues, including ARG237, ILE369, ARG194 and PHE379, were revealed to form critical interactions with inhibitor and play dominant roles during the inhibitor’s binding. In addition, the polarization effect was shown to significantly influence PCSK9–ligand binding. The identified inhibitor exhibited highly similar binding patterns with two known active compounds, providing valuable insights for the rational design and optimization of small-molecule inhibitors targeting PCSK9. This work contributes to the development of more effective treatments for hyperlipidemia and associated cardiovascular diseases. Full article

The integration of energy-active elements into the building envelope in the form of large-area heating/cooling, active thermal protection (ATP), thermal barriers (TB), and TABS represents a technical solution that is consistent with the principles of energy sustainability, resilience, and adaptability to climate change and ensures affordable and clean energy for all while protecting the climate in the context of the UN Sustainable Development Goals. The aim and innovation of our research is to develop energy multifunctional facades (EMFs) that are capable of performing a dual role, which includes the primary known energy functions of end elements and the additional innovative ability to serve as a source of heat/cooling/electricity. This new function of EMFs will facilitate heat dissipation from overheated facade surfaces, preheating of hot water, and electricity generation for the operation of building energy systems through integrated photovoltaic components. The theoretical assumptions and hypotheses presented in our previous research work must be verified by experimental measurements with predictions of the optimal operation of building energy systems. Most existing studies on thermal barriers are based on calculations. However, there are few empirical measurements that quantify the benefits of ATP in real operation and specify the conditions under which different types of ATP are feasible. In this article, we present the development, design, and implementation of an experimental prototype of a prefabricated building module with integrated energy-active elements. The aim is to fill the knowledge gaps by providing a comprehensive framework that includes the development, research, design, and implementation of combined energy systems for buildings. The design of energy systems will be developed in BIM. An important result of this research is the development of a technological process for the implementation of a contact insulation system with integrated ATP in modular and panel buildings with a lightweight envelope. Full article

It is essential to develop the optimal hot-working process of the (CoCrNi)₉₄Al₃Ti₃ alloy, a recently developed precipitation-hardened medium-entropy alloy with promising mechanical properties, for its industrial application. In this study, the hot workability of the as-forged (CoCrNi)₉₄Al₃Ti₃ alloy was investigated over a temperature range of 1000 °C to 1150 °C and a strain rate ranging from 0.001 to 1 s⁻¹ using a Gleeble-1500D thermal simulation machine of Dynamic Systems Inc., USA. As a result, the constitutive relationship was established, and the hot deformation activation energy was calculated as 433.2 kJ/mol, suggesting its well-defined plastic flow behavior under low-energy-input conditions. Hot-processing maps were constructed to identify the stable hot-working regions. Microstructure analysis revealed that the hot-forged (CoCrNi)₉₄Al₃Ti₃ alloy exhibited continuous dynamic recrystallization (CDRX) behavior under optimal hot-working conditions. Considering the hot-processing maps and DRX characteristics, the optimal hot-working window of hot-forged (CoCrNi)₉₄Al₃Ti₃ alloy was identified as 1100 °C with a strain rate of 0.1 s⁻¹. This work offers valuable guidance for developing high-efficiency forming processes for (CoCrNi)₉₄Al₃Ti₃ medium-entropy alloy. Full article

Geothermal resources represent one of the most vital renewable energy sources, offering substantial development potential within the energy sector. Wudalianchi, renowned as one of China’s prominent volcanic clusters, has undergone extensive underground volcanic activities, suggesting a promising capacity for geothermal resource accumulation. This paper is the first to apply the cross-gradient gravity-magnetic joint inversion method to study the shallow structures in the Laoheishan Volcano and surrounding areas of Wudalianchi, based on high-precision measured gravity and magnetic data. The inversion results indicate the presence of a rock body at a depth of approximately 2 km beneath the Laoheishan and Bijiashan regions, which simultaneously exhibits characteristics of low density, high magnetization, and low seismic velocity. Integrating previous research findings, the rock body is interpreted as basalt formed during magmatic activity, retaining remanent magnetism. Furthermore, the rock body contains fractures filled with fluids, thereby excluding the possibility of a shallow magma chamber or dry hot rocks beneath the Laoheishan area. These rock bodies are interconnected at depth and align with the NE and SE fault directions in the Wudalianchi area, confirming that these faults govern the region’s volcanic activities. The inversion results, from the perspectives of density and magnetic susceptibility, elucidate the material distribution in the shallow subsurface of the Laoheishan and surrounding areas, providing new evidence for further exploration of geothermal resources in the region. Full article

The traditional hot-dip tinning processes face challenges in controlling excessive copper dissolution and interfacial instability. This study involved designing a dissolution experiment using the hot-dip tin plating process. Through microscopic characterization and dissolution kinetics analysis, it systematically revealed the regulatory mechanism of trace Ni addition (0–0.5 wt.%) on the dissolution behavior and interfacial reaction of copper wire in a tin alloy melt. The experiment showed that Ni atoms formed a (Cu_1−x,Ni_x)₆Sn₅ ternary phase by replacing Cu in the Cu₆Sn₅ lattice, resulting in a transformation of the grain morphology of the IMC layer from equiaxed to fibrous. At the same time, the addition of Ni changed the kinetics of the interfacial reaction, effectively increasing the activation energy from 40.84 kJ/mol in the pure Sn system to 54.21 kJ/mol in the Sn-0.5Ni system, which extended the complete dissolution time of the copper wire at 573 K by three times. Full article

In this study, survey methods including seismic techniques and controlled-source audio-frequency magnetotelluric, drilling, and pumping tests were employed to investigate the geothermal systems and their formation mechanisms in northern Shanxi Province, China. The following characteristics were observed: (1) Geothermal resources in northern Shanxi Province are primarily located in Archean metamorphic rocks and fracture zone aquifer groups. The direct heat source is likely uncooled magma chambers in the middle-upper crust, whereas the overlying layers consist of Quaternary, Neogene, and Paleogene deposits. (2) The high-temperature geothermal system is of the convective-conductive type: atmospheric precipitation and surface water infiltrate pore spaces and fault fractures to reach thermal storage, where they are heated. Hot water then rises along the fracture channels and emerges as shallow hot springs, and ongoing extensional tectonic activity has caused asthenospheric upwelling. The partial melting of the upper mantle forms basic basaltic magma, which ascends to the middle-upper crust and forms multiple magma chambers. Their heat is transferred to the shallow subsurface, causing geothermal anomalies. (3) Borehole YG-1 findings revealed that these geothermal resources are primarily static reserves. Our findings provide a foundation for further geothermal development in the region, including the strategic deployment of wells to improve geothermal energy extraction. Full article

In response to the intensifying competition in the mold market and the increasingly stringent specifications of die forgings, the existing 55NiCrMoV7 (MES 1 steel) material can no longer meet the elevated demands of customers. Consequently, this study systematically optimizes the alloy composition of MES 1 steel by precisely adjusting the molybdenum (Mo) and vanadium (V) contents. The primary objective is to significantly enhance the microstructure and thermal–mechanical fatigue performance of the steel, thereby developing a high-performance, long-life hot working die steel designated as MES 2 steel. The thermal–mechanical fatigue (TMF) tests of two test steels were conducted in reverse mechanical strain control at 0.6% and 1.0% strain levels by a TMF servo-hydraulic testing system (MTS). The microstructures of the two steels were characterized using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). The results indicate that throughout the entire thermomechanical fatigue cycle, both steels exhibit initial hardening during the low-temperature half-cycle (tension half-cycle) and subsequent continuous softening during the high-temperature half-cycle (compression half-cycle). Furthermore, under the same strain condition, the cumulative cyclic softening damage of MES 1 steel is more pronounced than that of the newly developed MES 2 steel. The number, width, and length of cracks in MES 2 steel are smaller than those in MES 1 steel, and the thermomechanical fatigue life of MES 2 steel is significantly longer than that of MES 1 steel. The microstructures show that the main precipitate phase in MES 1 steel is Cr-dominated rod-shaped carbide. It presents obvious coarsening and is prone to inducing stress concentration, thus facilitating crack initiation and propagation. The precipitate phase in MES 2 steel is mainly MC carbide containing Mo and V. It has a high thermal activation energy and is dispersed in the matrix in the form of particles, pinning dislocations and grain boundaries. This effectively delays the reduction in dislocation density and grain growth, thus contributing positively to the improvement in thermomechanical fatigue performance. Full article

The hot forming-quenching integrated process (HFQ^®) organically combines the deformation and heat treatment, which can improve the forming performance of aluminum alloy while ensuring the final strength of formed parts. Thermal deformation in HFQ^® has a non-negligible influence on precipitation behavior in subsequent artificial aging treatment and affects the mechanical properties of the formed parts. In this study, the relationship between the precipitation behavior and thermal deformation ratios was investigated. Results indicated that the formation temperatures of η′ and η decreased with an increasing deformation ratio; however, the former decreased more than the latter. The activation energy of η′ precipitation decreased linearly with increasing deformation ratio. Additionally, the phase transition fraction of η′ increased with the deformation ratio, leading to shorter times required to reach equivalent phase transition fractions. Deformation accelerated the phase transition of η′, and greater deformation resulted in a shorter transition time. The aging time required for peak Vickers hardness decreased with increasing deformation ratio, reflecting the promotion of precipitated phase formation and transformation by introduced dislocations. Consequently, peak hardness and yield strength were achieved in shorter aging times. In terms of industrial applications, this discovery offers significant advantages for shortening the production cycle of the hot stamping process and reducing production costs. Full article

Ti-6.5Al-2Zr-1Mo-1V/TiB metal matrix composites with 3 wt.% of TiB₂ were obtained using vacuum arc melting and spark plasma sintering methods and compared with an unreinforced Ti-6.5Al-2Zr-1Mo-1V alloy. The microstructures of the unreinforced Ti6.5Al-2Zr-1Mo-1V alloy in the as-cast and as-sintered conditions were quite typical and consisted of colonies of α-lamellae embedded in the β matrix. The microstructure of the as-cast Ti-6.5Al-2Zr-1Mo-1V/TiB composite composed of TiB fibers randomly distributed within the two-phase α/β matrix, while the as-sintered composite had a network-like microstructure, in which areas of the two-phase α/β matrix were delineated by walls of TiB fibers. At room temperature, the yield strength of the as-cast and as-sintered Ti-6.5Al-2Zr-1Mo-1V alloy were 800 and 915 MPa, respectively, with a plasticity of 18% in both conditions. The addition of TiB fibers contributed to a ~40 and 50% strength increment, with values of 1100 and 1370 MPa for the as-cast and as-sintered composites, respectively. In the as-sintered composite, the strengthening effect reduced at 400 °C and almost disappeared at elevated temperatures of 800–950 °C. The as-cast composite showed much higher strength during warm and hot deformation—at 800–950 °C, the yield strength of the as-cast composite was 50% higher compared to the Ti-6.5Al-2Zr-1Mo-1V unreinforced alloy. A higher rate and degree of globularization were established for the as-cast composite compared to the unreinforced alloy. For the as-sintered composite, a noticeably lower rate and degree of globularization was shown. During hot compression of the as-cast composite, TiB fibers reoriented towards the metal flow direction, while the network microstructure formed in the as-sintered composite transformed into clusters of borides unevenly distributed within the matrix. Based on the obtained results, the apparent activation energy of plastic deformation was calculated, and the operating deformation mechanisms were discussed both for the as-cast and as-sintered composites. The Arrhenius flow stress model and the dynamic material model were used to evaluate the deformation behavior of composites beyond the experimentally studied temperatures and strain rates. Full article

Background: Postmenopausal women frequently encounter a range of symptoms, including fatigue, diminished physical strength, reduced energy levels, vasomotor symptoms such as hot flushes, and vaginal atrophy, all of which adversely affect their overall quality of life. Engaging in physical activity and structured exercise may effectively alleviate these symptoms and enhance overall well-being. The present study aimed to investigate the relationship between physical activity and quality of life in postmenopausal Greek women. Methods: This cross-sectional clinical study included 219 postmenopausal women. Women with natural menopause for at least 12 consecutive months were enrolled in this descriptive, cross-sectional study. The female participants were asked to fill out the International Physical Activity Questionnaire-short form (IPAQ), the Hospital Anxiety and Depression Scale (HADS), and the EuroQol (EQ-5D-5L) instrument. Anthropometric measurements included weight, height, and waist circumference measurements. Results: A total of 219 postmenopausal women with an age of 61.4 ± 6.1 years and body mass index (BMI) of 25.6 ± 3.7 kg/m² were studied. Out of the total postmenopausal women studied, 64.8% were physically active. The mean value of MET-min/week was M = 1383.46 ± 1030.12. Physical activity among postmenopausal Greek women showed a strong correlation of PA with quality of life (r = 0.5; p ≤ 0.001) and age (r = 0.55; p ≤ 0.001) and a medium correlation with the HADS (r = 0.4; p ≤ 0.05). Conclusions: There was a 64.8% prevalence of physically active postmenopausal Greek women. The findings underscore the significance of fostering physical activity and quality of life among postmenopausal women to formulate efficacious therapeutic interventions. The results demonstrate a correlation between physical activity and the age of female participants, quality of life, and the HADS and can be used to improve postmenopausal women’s physical activity levels, which is recommended as a strategy for improving the quality of life in postmenopausal women. Full article

The effect of an erbium alloying on the hot deformation behavior of the crossover Al3Zn3Mg3Cu0.2Zr alloy was investigated in detail. First of all, Er increases the solidus temperature of the alloy. This allows hot deformation at a higher temperature. The precipitates resulting from the Er alloying of the Al3Zn3Mg3Cu0.2Zr alloy were analyzed using transmission electron microscopy. Erbium addition to the alloy produces the formation of more stable and fine L1₂-(Al₃(Zr, Er)) precipitates with a size of 20–60 nm. True stress tends to increase with a decline in the temperature and an increase in the deformation rate. The addition of Er leads to decreases in true stress at the strain rates of 0.01–1 s⁻¹ due to particle-stimulated nucleation softening mechanisms. The effective activation energy of the alloy with the Er addition has a lower value, enabling an easier hot deformation process in the alloy with an elevated volume fraction of the intermetallic particles. The addition of Er increases the strain rate sensitivity, which makes the failure during deformation less probable. The investigated alloys have a significant difference in the dependence of the activation volume on the temperature. The flow instability criterion allows better deformability of Er-doped alloys and enables the alloys to be formed more easily. The evenly distributed particles prevent the formation of shear bands with elevated storage energy and decrease the probability of crack initiation during the initial stages of hot deformation when only one softening mechanism (dynamic recovery) is working. The microstructure analysis proves that dynamic recovery is the main softening mechanism. Full article

During the hot pressing of pure titanium and different carbon steels in a temperature range of $\vartheta$ = 950–1050 $°\mathrm{C}$, a compound layer up to d_L≈10 $\mu \mathrm{m}$ thick is formed at the titanium–steel interface. With a higher carbon content of the used steel, the layer thickness increases. The carbon concentration within the layer is in the range of stoichiometry for TiC. Apart from TiC, no other phases can be detected by X-ray diffraction (XRD) measurements inside the formed layer. The calculation of the activation energy for the TiC layer formation is Q = 126.5–136.7 $\mathrm{kJ}$ mol⁻¹ and is independent of the carbon content of the steel. The resulting microstructure has a grain size gradient, wherein the mechanical properties, such as hardness and Young‘s modulus, are almost constant. Statistical analysis using Response Surface Methodology (RSM) indicates that the carbon content of the steel has the most significant influence on layer thickness, followed by annealing temperature and annealing time. By selecting the appropriate carbon steel and the subsequent removal of the steel, it is possible to produce targeted TiC layers on titanium substrates, which holds enormous potential for this material in wear-intensive applications. Full article

Converting carbon dioxide (CO₂) into high-value-added chemicals using solar energy is a promising approach to reducing carbon dioxide emissions; however, single photocatalysts suffer from quick the recombination of photogenerated electron–hole pairs and poor photoredox ability. Herein, silver (Ag) nanoparticles featuring with localized surface plasmon resonance (LSPR) are combined with g-C₃N₄ to form a Schottky junction for photothermal catalytic CO₂ reduction. The Ag/g-C₃N₄ exhibits higher photocatalytic CO₂ reduction activity under UV-vis light; the CH₄ and CO evolution rates are 10.44 and 88.79 µmol·h⁻¹·g⁻¹, respectively. Enhanced photocatalytic CO₂ reduction performances are attributed to efficient hot electron transfer in the Ag/g-C₃N₄ Schottky junction. LSPR-induced hot electrons from Ag nanoparticles improve the local reaction temperature and promote the separation and transfer of photogenerated electron–hole pairs. The charge carrier transfer route was investigated by in situ irradiated X-ray photoelectron spectroscopy (XPS). The three-dimensional finite-difference time-domain (3D-FDTD) method verified the strong electromagnetic field at the interface between Ag and g-C₃N₄. The photothermal catalytic CO₂ reduction pathway of Ag/g-C₃N₄ was investigated using in situ diffuse reflectance infrared Fourier transform spectra (DRIFTS). This study examines hot electron transfer in the Ag/g-C₃N₄ Schottky junction and provides a feasible way to design a plasmonic metal/polymer semiconductor Schottky junction for photothermal catalytic CO₂ reduction. Full article

GH4720Li is an advanced nickel-based alloy celebrated for its remarkable high-temperature strength. This study aimed to investigate the dynamic recrystallization (DRX) behavior of novel GH4720Li superalloys microalloyed with 0.3Y via hot compression tests. A constitutive model was formulated to simulate the DRX behavior. Utilizing the stress–strain curve, the activation energy for the alloy was determined using both the Arrhenius model and the Z-parameter equation, resulting in 1117.916 kJ/mol. The microstructure evolution analysis conducted revealed that lower strain rates at elevated temperatures effectively hindered the occurrence of DRX. Conversely, the increase in the strain rate promoted DRX, producing uniform, equiaxial grains. Recrystallization calculations, along with validation experiments, demonstrated the efficacy of the Avrami model in establishing a DRX model for the alloy during hot deformation. This model accurately quantified DRX percentages under varying deformation parameters, showcasing strong agreement with the microstructure test results. The predictive capability afforded by the developed models offers valuable insights for optimizing the alloy’s forging process. During the compression of the novel GH4720Li superalloy, DRX initiates when the dislocation density in a specific region surpasses a critical threshold. Concurrently, dislocation accumulation near the grain boundaries exceeds that within the grains themselves, highlighting that newly formed DRXed grains primarily emerge along the deformed grain boundaries. Full article