Search Results (5)

During the detailed design of magnets for the storage ring of Siam Photon Source II (SPS-II), the influence of magnetic crosstalk between adjacent magnets in the compact Double Triple Bend Achromat (DTBA) lattice was investigated. Using Opera-3D magnetostatic simulation, six magnet pairs were analyzed to investigate the changes in magnetic field distribution along the electron trajectory and integrated magnetic field within each magnet aperture. The study employed polynomial and Fourier analyses to calculate multipole field components. Results indicate that magnetic crosstalk affects the field distribution in the region between magnets, particularly for the defocusing quadrupole and dipole magnets (QD2-D01) and the focusing quadrupole and octupole magnets (QF42-OF1) pairs, which have the pole-to-pole distances of 153.37 mm and 116.45 mm, respectively. Although these separations exceed the estimated fringe field regions, deviations of up to 1% in the main field components were observed. Notably, even an unpowered neighboring magnet contributes to magnetic field distortion due to the modified magnetic flux distribution. Crosstalk effects on the higher-order multipole fields are mostly within the acceptable limit, except for the extra quadrupole field from QD2 found in the dipole D01 magnet. This study highlights the effects of magnetic interference in tightly packed lattice and underscores the need to include a complete multipole field data with crosstalk consideration in the SPS-II lattice model in order to ensure an accurate beam dynamics simulation and predict the operating current adjustments for machine commissioning. Full article

The performance and beam quality of the new fourth-generation synchrotron light source with ultra-low emittance are highly susceptible to coupled-bunch instabilities. These instabilities arise from the interaction between the bunched electron beam and the surrounding vacuum chamber installations. To mitigate these effects, the installation of a transverse bunch-by-bunch feedback system is planned. This system will comprise a button-type beam position monitor (BPM) for beam signal detection, a digital feedback controller, a broadband power amplifier, and a broadband stripline kicker as the primary actuator. One of the critical challenges lies in the development of the stripline kicker, which must be optimized for high shunt impedance and wide bandwidth while minimizing beam-coupling impedance. This work focuses on the comprehensive design of the stripline kicker intended for transverse (horizontal and vertical) bunch-by-bunch feedback in the Siam Photon Source II (SPS-II) storage ring. The stripline kicker design also incorporates features to enable its use for beam excitation in the SPS-II tune measurement system. The optimization process involves analytical approximations and detailed numerical electromagnetic field analysis of the stripline’s 3D geometry, focusing on impedance matching, field homogeneity, power transmission, and beam-coupling impedance. The details of engineering design are discussed to ensure that it meets the fabrication possibilities and stringent requirements of the SPS-II accelerator. Full article

The development of a prototype booster magnet for the Siam Photon Source II (SPS-II) was launched in 2023 as a milestone in advancing accelerator technology through domestic manufacturing capabilities in Thailand. In the SPS-II booster lattice, the magnet integrates focusing quadrupole and sextupole functions into a combined-function quadrupole-sextupole magnet, enabling a more compact lattice and reducing the total number of magnets required. To meet the required magnet specifications, the design was carefully optimized using Opera-3D software (version 2021) to achieve a quadrupole gradient of 19.395 T/m and a sextupole gradient of 22.327 T/m² over an effective magnetic length of 0.25 m, while maintaining a magnetic field homogeneity better than 1 × 10⁻³. A key manufacturing challenge involved fabricating laminated magnet cores and establishing precise production processes. Magnetic field measurements performed on the prototype using the Hall-probe technique validated the magnet’s quality and accuracy. This paper presents the overall development process, including the magnet design, details of the magnetic field simulation methodology, prototype fabrication, and initial magnetic field measurements. Full article

A prototype of a combined horizontal and vertical correcting magnet was designed and fabricated for the 3 GeV storage ring of Siam Photon Source II, which will be the second synchrotron light source in Thailand. The magnet will be employed for fast-orbit feedback correction, with a required magnetic field integral of approximately 8 Tesla.mm. The magnet pole and yoke were manufactured using laminated silicon steel to minimize hysteresis and eddy current losses during operation. Magnet modeling and magnetic field calculations were performed using Opera-3D. The size of the gap between the magnet poles is limited by the size of the vacuum chamber over which the magnet will be installed; in this case, it was designed to be 65 mm. Mechanical analysis of the structure of the magnet was performed using SOLIDWORKS and ANSYS. Magnetic field measurements were obtained using the Hall probe technique. The entire prototype, from its design to manufacturing and measurement, was completed in-house. This design will be appropriate for application at the Siam Photon Source II storage ring. Full article

A prototype of a type A quadrupole magnet has been designed and manufactured for the 3 GeV storage ring of Siam Photon Source II, the second synchrotron light source in Thailand. The required quadrupole gradient is 51 T/m with the magnet effective length being 162 mm. Magnet modeling and magnetic field calculation were performed using Radia and Opera-3D. The bore radius of the magnet is 16 mm. The magnet will be operated at the excitation of 5544 A-turns. A mechanical analysis of the magnet structure was performed in SOLIDWORKS and ANSYS, where the maximum deformation of 0.003 mm was found at the magnet poles, and the first-mode natural frequency was higher than 100 Hz. The magnet yoke is made of AISI 1006 low-carbon steel with a fabrication tolerance of ±0.020 mm. Magnet coils are water-cooled and made of high-purity copper. The temperature rise of the coils was below 3.0 °C at the maximum excitation of 6664 A-turns, which is 20% above the operating point. Magnetic field measurement was carried out using the Hall probe technique. The measured magnetic field and coil temperature of the prototype show good agreement with the calculations. Full article