Search Results (5)

In this paper, we report the effect of metal oxide (Fe₂O₃) loading in different weight ratios (0.5%, 1%, 2%, and 4%) on the structural and electrical parameters, viz., the complex dielectric constant, electric modulus spectra, and the AC conductivity, of polymeric composites of PVDF/PMMA (30/70 weight ratio) blend. The structural and geometric measurements have been analyzed with the help of peak location, peak intensity, and peak shape obtained from XRD as well as from FTIR spectra. The electrical properties have been investigated using an impedance analyzer in the frequency range 100 Hz to 1 MHz. The real parts of the complex permittivity and the dielectric loss tangent of these materials are found to be frequency independent in the range from 20 KHz to 1 MHz, but they increase with the increase in the concentration of nano-Fe₂O₃. The conductivity also increases with an increased loading of Fe₂O₃ in PVDF/PMMA polymer blends. The electric modulus spectra were used to analyze the relaxation processes associated with the Maxwell–Wagner–Sillars mechanism and chain segmental motion in the polymer mix. Full article

In today’s contemporary civilization, there is a growing need for clean energy focused on preserving the environment; thus, dielectric capacitors are crucial equipment in energy conversion. On the other hand, the energy storage performance of commercial BOPP (Biaxially Oriented Polypropylene) dielectric capacitors is relatively poor; hence, enhancing their performance has drawn the attention of an increasing number of researchers. This study used heat treatment to boost the performance of the composite made from PMAA and PVDF, combined in various ratios with good compatibility. The impacts of varying percentages of PMMA-doped PMMA/PVDF mixes and heat treatment at varying temperatures were systematically explored for their influence on the attributes of the blends. After some time, the blended composite’s breakdown strength improves from 389 kV/mm to 729.42 kV/mm at a processing temperature of 120 °C. Consequently, the energy storage density is 21.12 J/cm³, and the discharge efficiency is 64.8%. The performance has been significantly enhanced compared to PVDF in its purest state. This work offers a helpful technique for designing polymers that perform well as energy storage materials. Full article

In miscible crystalline/amorphous polymer blends, the exclusion behaviors of the latter with various molecular weights during the crystallization of the former were investigated by the combination of SAXS and DSC by taking a PVDF/PMMA blend as an example. The ratio between internal crystallinity from SAXS and overall crystallinity of the entire blend from DSC was employed to characterize the exclusion of PMMA. Our results indicate that the molecular weight of the amorphous component produces a remarkable influence on the diffusion coefficient (D) and the crystal growth rate (G) of the crystalline component. There are both inter-lamellar and inter-fibrillar structures when PVDF blended with lower-molecular-weight PMMA. With increasing molecular weight of PMMA, the decrease in crystal growth rate (G) dominates the enhanced exclusion behaviors of PMMA, resulting in bigger pores after extraction. Our results are significant not only for the basic understanding of crystallization in polymer blends, but also for the fabrication and structure control of porous structures based on crystallization templates. Full article

Electroactive polymers with high dielectric constants and low moduli can offer fast responses and large electromechanical strain under a relatively low electric field with regard to theoretical driving forces of electrostriction and electrostatic force. However, the conventional electroactive polymers, including silicone rubbers and acrylic polymers, have shown low dielectric constants (ca. < 4) because of their intrinsic limitation, although they have lower moduli (ca. < 1 MPa) than inorganics. To this end, we proposed the high dielectric PVDF terpolymer blends (PVTC-PTM) including poly(vinylidene fluoride-trifluoroethylene-chlorofluoro-ethylene) (P(VDF-TrFE-CFE), PVTC) as a matrix and micelle structured poly(3-hexylthiophene)-b-poly(methyl methacrylate) (P3HT-b-PMMA, PTM) as a conducting filler. The dielectric constant of PVTC-PTM dramatically increased up to 116.8 at 100 Hz despite adding only 2 wt% of the polymer-type filler (PTM). The compatibility and crystalline properties of the PVTC-PTM blends were examined by microscopic, thermal, and X-ray studies. The PVTC-PTM showed more compatible blends than those of the P3HT homopolymer filler (PT) and led to higher crystallinity and smaller crystal grain size relative to those of neat PVTC and PVTC with the PT filler (PVTC-PT). Those by the PVTC-PTM blends can beneficially affect the high-performance electromechanical properties compared to those by the neat PVTC and the PVTC-PT blend. The electromechanical strain of the PVTC-PTM with 2 wt% PTM (PVTC-PTM2) showed ca. 2-fold enhancement (0.44% transverse strain at 30 V_pp μm⁻¹) relative to that of PVTC. We found that the more significant electromechanical performance of the PVTC-PTM blend than the PVTC was predominantly due to the electrostrictive force rather than electrostatic force. We believe that the acquired PVTC-PTM blends are great candidates to achieve the high-performance electromechanical strain and take all benefits derived from the all-organic system, including high electrical breakdown strength, processibility, dielectrics, and large strain, which are largely different from the organic–inorganic hybrid nanocomposite systems. Full article

The compatibilizer with double comb structure has a superior compatibilizing effect for immiscible polymer blends due to the symmetrical structure on both sides of main chains. Extensive study related to the architectural effects of compatibilizer on the compatibilization has mainly focused on the side chains. We investigated the influence of the compatibilizer-main-chain structure on the compatibilizing effect for immiscible poly(vinylidene fluoride)/poly(L-lactic acid) (PVDF/PLLA) blends. Two reactive-comb compatibilizers with polystyrene (PS) and polymethylmethacrylate (PMMA) as main chains and PMMA as the side chains have been synthesized. PS is immiscible with both PLLA and PVDF, while PMMA is miscible with PVDF. It was found that both compatibilizers can improve the compatibility between the PLLA and PVDF, with different compatibilization effects. In the PVDF/PLLA (50/50) blends, 1 wt.% poly(styrene-co-glycidyl methacrylate)-graft-poly(methyl methacrylate) (RC–SG) tuned the morphology from the droplet-in-matrix structure to the co-continuous structure, while the blends with poly(methyl methacrylate-co-glycidyl methacrylate)-graft-poly(methyl methacrylate) (RC–MMG) kept the sea-island structure with even 3 wt.% loading. Moreover, RC–SG induces a wider co-continuous interval range than RC–MMG. The co-continuous structure obtained by RC–SG was also more stable than that by RC–MMG. It was further found that RC–SG-compatibilized PVDF/PLLA blends exhibit higher mechanical properties than the RC–MMG-compatibilized blends. Full article