Search Results (6)

To address unavailable global navigation satellite system (GNSS) signals, dense metallic equipment, valve-tower occlusion, and the insufficient robustness of single-sensor localization in unmanned aerial vehicle (UAV) inspection of converter valve halls, this paper proposes a non-line-of-sight (NLOS)-aware LiDAR-ultra-wideband (UWB) fusion localization method. The method uses LiDAR odometry to provide continuous local motion constraints and UWB ranging to provide global distance constraints. The geometric relationship among the UAV, UWB anchors, and valve-hall obstacles is used to evaluate the NLOS risk of each UWB link, and the equivalent ranging variance is adaptively adjusted before tight fusion optimization. To avoid overextending simulation conclusions, this study focuses on localization-layer modeling and simulation-based validation rather than full energized valve-hall flight deployment. In the grouped-bushing valve-hall scenario, the proposed method achieves an RMSE of 0.30 m, a mean error of 0.29 m, a P95 error of 0.43 m, and a maximum error of 0.48 m, reducing the RMSE by 50.0% compared with ordinary tight LiDAR-UWB fusion. Additional Monte Carlo tests under different trajectories, anchor layouts, anchor installation errors, and obstacle densities further verify the robustness of the proposed weighting mechanism. The results indicate that the method can suppress LiDAR accumulated drift and reduce the influence of UWB NLOS ranging in GNSS-denied metallic indoor environments, while real converter-valve-hall flight tests under energized electromagnetic conditions remain necessary before engineering deployment. Full article

Indoor companion, rehabilitation, logistics, laboratory transport, and service robot scenarios require mobile platforms that can follow a human operator safely and flexibly under lighting changes, occlusion, texture-poor corridors, and dynamic pedestrian environments. Vision-, LiDAR-, and UWB-based following systems can provide high perception capability, but their deployment cost, environmental dependence, and sensing complexity remain limiting factors for low-perception-dependence applications. This paper presents a passive following system for a Mecanum-wheel mobile platform based on gimbal posture perception and orthogonal odometry fusion. A rope-tensioned two-axis gimbal is mounted above a 300 mm × 300 mm × 150 mm omnidirectional chassis, and a six-axis inertial sensor installed at the top of the gimbal detects pitch and roll changes induced by user traction. A piecewise posture-to-velocity mapping model with a dead zone, saturation, low-pass filtering, and acceleration limiting converts the user’s traction intention into planar velocity commands in the vehicle coordinate frame. To reduce pose errors caused by Mecanum-wheel slip and discontinuous roller-ground contact, two orthogonal passive odometry wheels and inertial attitude estimation are fused to provide planar position feedback for closed-loop following. A prototype was implemented using an Infineon TRAVEO CYT4BB77 controller, TI DRV8701E motor drivers, six-axis IMUs, magnetic encoders, and an embedded display interface. Experiments evaluated attitude estimation accuracy, planar localization accuracy, passive following performance, gyroscope compensation, and open-loop/closed-loop following. The compensated attitude module achieved a static yaw drift of 0.45 deg/h and a dynamic attitude RMSE below 0.56 deg. Orthogonal odometry fusion produced an average positioning error of 3.8 mm over a 3000 mm linear displacement, reducing error by approximately 84.6% compared with pure Mecanum-wheel drive odometry. In a 5000 mm forward traction task, closed-loop following reduced the average distance error from 38.6 mm to 11.5 mm compared with open-loop attitude mapping. The results indicate that the proposed gimbal-orthogonal odometry architecture provides a compact, intuitive, and environment-robust solution for passive following on omnidirectional mobile platforms. Full article

Mobile robots operating in structured indoor environments face significant challenges including the “kidnapped robot” problem, sensor accumulation errors, and environmental perceptual ambiguity, which collectively lead to slow convergence and inadequate accuracy in relocalization. To address these critical issues, this paper proposes an Adaptive Fusion Relocalization Algorithm (AFRA) based on a likelihood-field measurement model. The core innovations of AFRA include the construction of a refined likelihood-field model that effectively integrates LiDAR and Ultra-Wideband (UWB) data, significantly enhancing the accuracy of observation likelihood through probabilistic modeling of hybrid noise. Furthermore, a particle filter framework incorporating dynamic particle scheduling and adaptive resampling mechanisms is developed to achieve an optimal balance between precision and computational efficiency. The Experimental results demonstrate that AFRA maintains relocalization errors within ±0.035 m, improving accuracy by 45.3% compared to the best-performing single sensor, while achieving a 40.7% acceleration in convergence speed. These advancements substantially enhance the robustness and real-time performance of mobile robot localization in complex scenarios. Full article

The increasing risk to Vulnerable Road Users (VRUs) at urban intersections necessitates advanced safety mechanisms capable of operating effectively under diverse conditions, including adverse weather like heavy rain. While optical sensors such as cameras and LiDAR often degrade in poor visibility, Radio Frequency (RF)-based systems offer resilient, all-weather tracking. This paper presents a novel approach to enhancing VRU protection by fusing two RF modalities: radar sensors and Ultra-Wideband (UWB) technology, a strong candidate for Joint Communication and Sensing (JCS). The research, conducted as part of the VIDETEC-2 project, addresses the limitations of existing vehicle-based and infrastructure-based systems, particularly in scenarios involving occlusions and blind spots. By leveraging radar’s environmental robustness alongside UWB’s precise, cost-effective short-range communication and localization, the proposed system delivers the framework for continuous vehicle and VRU tracking. The fusion of these sensor modalities, managed through a hybrid Kalman filter approach integrating an Unscented Kalman Filter (UKF) and an Extended Kalman Filter (EKF), allows reliable VRU tracking even in challenging urban scenarios. The experimental results demonstrate a reduction in tracking uncertainty and highlight the system’s potential to serve as a more accurate and responsive safety mechanism for VRUs at intersections. This work contributes to the development of intelligent road infrastructures, laying the foundation for future advancements in urban traffic safety. Full article

In this study, we propose a tightly coupled integrated method of ultrawideband (UWB) and light detection and ranging (LiDAR)-based simultaneous localization and mapping (SLAM) for global navigation satellite system (GNSS)-denied environments to achieve high-precision positioning with reduced drift. Specifically, we focus on non-line-of-sight (NLOS) identification and correction. In previous work, we utilized laser point cloud maps to identify and exclude NLOS measurements in real time to attenuate their severe effects on the integrated system. However, the complete exclusion of NLOS measurements will likely lead to deterioration in the dilution of precision (DOP) for the remaining line-of-sight (LOS) anchors, counterproductively introducing large positioning errors into the integrated system. Therefore, this study considers the ranging accuracy and geometric distribution of UWB anchors and innovatively proposes an NLOS correction method using a grey prediction model. For a poor line-of-sight (LOS) anchor geometric distribution, the grey prediction model is used to fill in the gaps by predicting the NLOS measurements based on historical measurements. Including the corrected measurements effectively improves the original poor geometric configuration, improving the system positioning accuracy. Since conventional filtering-based fusion methods are exceedingly sensitive to measurement outliers, we use state-of-the-art factor graph optimization (FGO) to tightly integrate the UWB measurements (LOS and corrected measurements) with LiDAR-SLAM. The temporal correlation between measurements and the redundant system measurements effectively enhance the robustness of the integrated system. Experimental results show that the tightly coupled integrated method combining NLOS correction and FGO improves the positioning accuracy under a poor geometric distribution, increases the system availability, and achieves better positioning than filtering-based fusion methods with a root-mean-square error of 0.086 m in the plane direction, achieving subdecimeter indoor high-precision positioning. Full article

Underwater positioning presents a challenging issue, because of the rapid attenuation of electronic magnetic waves, the disturbances and uncertainties in the environment. Conventional methods usually employed acoustic devices to localize Unmanned Underwater Vehicles (UUVs), which suffer from a slow refresh rate, low resolution, and are susceptible to the environmental noise. In addition, the complex terrain can also degrade the accuracy of the acoustic navigation systems. The applications of underwater positioning methods based on visual sensors are prevented by difficulties of acquiring the depth maps due to the sparse features, the changing illumination condition, and the scattering phenomenon. In the paper, a novel visual-based underwater positioning system is proposed based on a Light Detection and Ranging (LiDAR) camera and an inertial measurement unit. The LiDAR camera, benefiting from the laser scanning techniques, could simultaneously generate the associated depth maps. The inertial sensor would offer information about its altitudes. Through the fusion of the data from multiple sensors, the positions of the UUVs can be predicted. After that, the Bundle Adjustment (BA) method is used to recalculate the rotation matrix and the translation vector to improve the accuracy. The experiments are carried out in a tank to illustrate the effects and accuracy of the investigated method, in which the ultra-wideband (UWB) positioning system is used to provide reference trajectories. It is concluded that the developed positioning system is able to estimate the trajectory of UUVs accurately, whilst being stable and robust. Full article