Search Results (24)

As sensitive parts of the water treatment process, reverse osmosis (RO) membranes are the most important for desalination and wastewater treatment. But the performance of RO membranes deteriorates over time due to fouling, necessitating frequent replacements. One of the environmental challenges is the disposal of End-of-Life (EoL) RO membranes, which are made of non-biodegradable polymers. The reuse of EoL membranes as a sustainable approach for waste saving and resource efficiency has recently attracted considerable attention. The present work provides a comprehensive overview of the strategies for reusing EoL RO membranes as sustainable alternatives to conventional disposal methods. Furthermore, the fundamental principles of RO technology, the primary types and impacts of membrane fouling, and advanced cleaning and regeneration techniques are discussed. The conversion of EoL membranes into nanofiltration (NF), ultrafiltration (UF), and forward osmosis (FO) membranes is also covered in this review, as well as their uses in brackish water desalination, dye/salt separation, groundwater treatment, and household wastewater reuse. Environmental and economic benefits, as well as technical, social, and regulatory challenges, are also discussed. Finally, the review highlights innovative approaches and future directions for incorporating EoL membrane reuse into circular economy models, outlining its potential to improve sustainability and reduce operational costs in water treatment systems. Full article

The efficient removal of emulsified oil and trace organic pollutants via forward osmosis (FO) technology remains challenging due to limited water flux and membrane fouling. In this study, a series of metal oxide-modified PES-based composite FO membranes were fabricated and systematically evaluated to compare the effects of ZnO, Al₂O₃, and CuO nanoparticles on membrane structure and separation performance. The results demonstrated that the membrane modified with 0.04 g of ZnO nanoparticles achieved optimal synergy in terms of hydrophilicity, surface charge, and pore structure. The pure water flux increased from 5.48 L·m⁻²·h⁻¹ for the pristine membrane to 18.5 L·m⁻²·h⁻¹ for the ZnO-modified membrane, exhibiting a 237.5% increase in pure water flux compared to the pristine PES membrane, an oil rejection rate exceeding 97%, and over 95% rejection of typical negatively charged trace organic pollutants such as ibuprofen and tetracycline. Moreover, the ZnO-modified membrane showed excellent antifouling performance and structural stability in various organic solvent systems. This study not only optimized the interfacial chemistry and microstructure of the FO membrane but also enhanced pollutant repellence and the self-cleaning capability through increased hydrophilicity and surface negative charge density. These findings highlight the significant potential of ZnO modification for enhancing the overall performance of FO membranes and provide an effective strategy for developing high-performance, broadly applicable FO membranes for complex water purification. Full article

Sustainable development is linked to the achievement of several different objectives, as outlined by the 17 Sustainable Development Goals (SDGs) defined by the United Nations. Among them are the production of clean water and the combat of climate change, which is strictly linked to the use of fossil fuels as a primary energy source and their related CO₂ emissions. Water and energy are strongly interconnected. For instance, when processing water, energy is needed to pump, treat, heat/cool, and deliver water. Membrane operations for water treatment/desalination contribute to the recovery of purified/fresh water and reducing the environmental impact of waste streams. However, to be sustainable, water recovery must not be energy intensive. In this respect, this contribution aims to illustrate the state of the art and perspectives in desalination by reverse osmosis (RO), discussing the various approaches looking to improve the energy efficiency of this process. In particular, the coupling of RO with other membrane operations, like pressure-retarded osmosis (PRO), reverse electrodialysis (RED), and forward osmosis (FO), as well as the osmotic-assisted reverse osmosis (OARO) system, are reported. Moreover, the possibility of coupling a membrane distillation (MD) unit to an RO one to increase the overall freshwater recovery factor and reduce the brine volumes that are disposed is also discussed. Specific emphasis is placed on the strategies being applied to reduce the MD thermal energy demand, so as to couple the production of the blue gold with the fight against climate change. Full article

Pressure-Retarded Osmosis (PRO) is an osmotically driven membrane-based process that has recently garnered significant attention from researchers due to its potential for clean energy harvesting from salinity gradients. The complex interactions between mixed-mode channel flows and osmotic fluxes in real PRO membrane modules necessitate high-fidelity modeling approaches. In this work, an efficient CFD framework is developed for the 3D simulation of osmotically driven membrane processes. This approach is based on a two-way coupling between a CFD solver, which captures external concentration polarization (ECP) effects, and an analytical representation of internal concentration polarization (ICP). Consequently, the osmotic water flux and reverse salt flux (RSF) can be accurately determined, accounting for all CP effects without any limitations on the geometrical complexity of the membrane chamber or its flow mode/regime. The proposed model is validated against experimental data, showing good agreement across various PRO case studies. Additionally, the model’s flexibility to simulate other types of osmotically driven processes such as forward osmosis (FO) is examined. Thus, the contributions of ECP and ICP effects in local osmotic pressure drop along the membrane chamber are comprehensively compared for FO and PRO modes. Finally, the capability of the CFD model to simulate a lab-scale PRO module is demonstrated across a range of Reynolds numbers from low-speed laminar up to turbulent flow regimes. Full article

Osmotic microbial fuel cells (OsMFCs) with the abilities to simultaneously treat wastewater, produce clean water, and electricity provided a novel approach for the application of microbial fuel cell (MFC) and forward osmosis (FO). This synergistic merging of functions significantly improved the performances of OsMFCs. Nonetheless, despite their promising potential, OsMFCs currently receive inadequate attention in wastewater treatment, water reclamation, and energy recovery. In this review, we delved into the cooperation mechanisms between the MFC and the FO. MFC facilitates the FO process by promoting water flux, reducing reverse solute flux (RSF), and degrading contaminants in the feed solution (FS). Moreover, the water flux based on the FO principle contributed to MFC’s electricity generation capability. Furthermore, we summarized the potential roles of OsMFCs in resource recovery, including nutrient, energy, and water recovery, and identified the key factors, such as configurations, FO membranes, and draw solutions (DS). We prospected the practical applications of OsMFCs in the future, including their capabilities to remove emerging pollutants. Finally, we also highlighted the existing challenges in membrane fouling, system expansion, and RSF. We hope this review serves as a useful guide for the practical implementation of OsMFCs. Full article

The application of nanofiltration (NF) membranes in the forward osmosis (FO) process to remove heavy metal ions from wastewater is an emerging concept. Unlike NF, FO does not require an external driving force. Although the product, a dilute draw solution, must further be processed by NF to produce pure water and reconcentrate a draw solution, the feed to that NF process is “clean”, which minimizes membrane fouling. This paper examines the role of Cu²⁺ and Pb²⁺ in the feed solution on the water and the reverse solute fluxes in FO process using novel thin film nanocomposite (TFN) NF membranes. The TFN membranes were fabricated by in situ interfacial polymerization of piperazine (PIP) and 1,3,5-benzenetricarbonyl trichloride (TMC) containing different amounts of dispersed halloysite nanotubes (HNTs) nanoparticles functionalized with the first generation of poly(amidoamine) (PAMAM) dendrimers. The presence of Cu²⁺ and Pb²⁺ in the feed solution decreased the reverse flux of MgCl₂ by at least 2.5 times compared to the experiments with pure water as a feed. Simultaneously, the water flux also increased. The corresponding rejections of Cu²⁺ and Pb²⁺ in the FO process ranged from 94.5% to 98.1%. Full article

Forward osmosis membrane technology (FO) shows potential application prospects in biogas slurry concentration, which is conducive to promoting the sustainable development of biogas projects. However, at present, the key influencing factors of membrane concentration using FO are not well understood. Therefore, this study analyzed the influence of draw solution concentration, pH, temperature and cross-flow velocity on the concentration efficiency of FO membrane, and optimized the operation parameters of FO membrane. The results showed that the concentration effect of the NaCl draw solution at pH 5 or 9 was better than that at pH 7. The order of factor influencing the water flux was as follows: draw liquid concentration > cross-flow velocity > operating temperature. The optimal combination obtained by orthogonal analysis was under 45 °C, with a cross-flow velocity of 1 L/min and the use of 1.5 mol/L NaCl as draw solution. The results of the membrane cleaning implied that the recovery rate of the fouled membrane after acid–base cleaning is significantly higher (88%) than other cleaning solutions. This research offers a scientific reference for applying positive osmosis technology to re-utilize biogas slurry resources. Full article

Cellulose acetate (CA) is a semisynthetic, biodegradable polymer. Due to its characteristics, CA has several applications, including water membranes, filament-forming matrices, biomedical nanocomposites, household tools, and photographic films. This review deals with topics related to the CA membranes, which are prepared using different techniques, such as the phase inversion technique. CA membranes are considered very important since they can be used as microfiltration membranes (MF), ultrafiltration membranes (UF), nanofiltration membranes (NF), reverse osmosis (RO) membranes, and forward osmosis (FO) membranes. Membrane fouling results from the accumulation of materials that the membrane rejects on the surface or in the membrane’s pores, lowering the membrane’s flux and rejection rates. There are various forms of CA membrane fouling, for instance, organic, inorganic, particulate fouling, and biofouling. In this review, strategies used for CA membrane antifouling are discussed and summarized into four main techniques: feed solution pretreatment, cleaning of the membrane surface, membrane surface modification, which can be applied using either nanoparticles, polymer reactions, surface grafting, or surface topography, and surface coating. Full article

The major challenges in forward osmosis (FO) are low water flux, high specific reverse solute flux (SRSF), and membrane fouling. The present work addresses these problems by the incorporation of graphene quantum dots (GQDs) in the polyamide (PA) layer of thin-film composite (TFC) membranes, as well as by using an innovative polyethersulfone nanofiber support for the TFC membrane. The GQDs were prepared from eucalyptus leaves using a facile hydrothermal method that requires only deionized water, without the need for any organic solvents or reducing agents. The nanofiber support of the TFC membranes was prepared using solution blow spinning (SBS). The polyamide layer with GQDs was deposited on top of the nanofiber support through interfacial polymerization. This is the first study that reports the fouling resistance of the SBS-nanofiber-supported TFC membranes. The effect of various GQD loadings on the TFC FO membrane performance, its long-term FO testing, cleaning efficiency, and organic fouling resistance were analyzed. It was noted that the FO separation performance of the TFC membranes was improved with the incorporation of 0.05 wt.% GQDs. This study confirmed that the newly developed thin-film nanocomposite membranes demonstrated increased water flux and salt rejection, reduced SRSF, and good antifouling performance in the FO process. Full article

Microalgae have attracted great interest recently due to their potential for nutrients removal from wastewater, renewable biodiesel production and bioactive compounds extraction. However, one major challenge in microalgal bioremediation and the algal biofuel process is the high energy cost of separating microalgae from water. Our previous studies demonstrated that forward osmosis (FO) is a promising technology for microalgae harvesting and dewatering due to its low energy consumption and easy fouling control. In the present study, two FO module configurations (side-stream and submerged) were integrated with microalgae (C. vulgaris) photobioreactor (PBR) in order to evaluate the system performance, including nutrients removal, algae harvesting efficiency and membrane fouling. After 7 days of operation, both systems showed effective nutrients removal. A total of 92.9%, 100% and 98.7% of PO₄-P, NH₃-N and TN were removed in the PBR integrated with the submerged FO module, and 82%, 96% and 94.8% of PO₄-P, NH₃-N and TN were removed in the PBR integrated with the side-stream FO module. The better nutrients removal efficiency is attributed to the greater algae biomass in the submerged FO-PBR where in situ biomass dewatering was conducted. The side-stream FO module showed more severe permeate flux loss and biomass loss (less dewatering efficiency) due to algae deposition onto the membrane. This is likely caused by the higher initial water flux associated with the side-stream FO configuration, resulting in more foulants being transported to the membrane surface. However, the side-stream FO module showed better fouling mitigation by simple hydraulic flushing than the submerged FO module, which is not convenient for conducting cleaning without interrupting the PBR operation. Taken together, our results suggest that side-stream FO configuration may provide a viable way to integrate with PBR for a microalgae-based treatment. The present work provides novel insights into the efficient operation of a FO-PBR for more sustainable wastewater treatment and effective microalgae harvesting. Full article

FO membrane fouling mitigation during the concentration of cows’ urine was investigated. In particular, the effects on the permeability recovery of cleaning methods such as membrane washing with deionized (DI) water, osmotic backwash, and chemical cleaning were studied. The characterization of foulants that accumulated on the membrane surface was found to be rich in sugars and proteins. The foulants were effectively removed by de-ionized water circulation (washing) and osmotic backwash. While osmotic back was more effective, it did not fully recover the permeability of the membrane. The foulants absorbed in the membrane pores were found to be mainly composed of sugars. Soaking the membrane in a solution of NaClO enabled the removal of foulants absorbed inside the membrane. It was revealed that soaking in 1% NaClO solution for 30 min achieved the best results (83% permeability recovery), while soaking for a longer time (10 h) using 0.2% NaClO resulted in counterproductive results. Full article

In this study, the performance of a forward osmosis system was assessed over a 30-h period during desalination of a local oil refinery effluent using NaCl as the draw solute. The study was conducted with the active layer of the membrane facing the draw solution. Assessment was done based on the water flux, salt rejection (SO₄²⁻ and CO₃²⁻), membrane fouling and fouling reversal after membrane cleaning. Critical to this study was the performance of manual scrubbing of the membrane after each run and the application of chemically enhanced osmotic backwash. Scanning electron microscope (SEM) analysis of the cellulose triacetate (CTA) membrane was conducted before and after cleaning to ascertain the degree of fouling and fouling reversal after membrane cleaning. The results showed an average water flux of 3.78 ± 0.13 L/m² h, reverse solute flux (RSF) of 1.56 ± 0.11 g/m²·h, SO₄²⁻ rejection of 100%, CO₃²⁻ rejection of 95.66 ± 0.32% and flux recovery of 95% after membrane cleaning. This study identifies that intermittent manual scrubbing of the membrane plays a major role in overall membrane performance. It also provides a practical basis for further research and decision making in the use of FO and CTA membranes for oil refinery effluent desalination. Full article

Forward osmosis (FO) is an emerging process to dewater whey streams energy efficiently. The driving force for the process is the concentration gradient between the feed (FS) and the concentrated draw (DS) solution. Here we investigate not only the effect of the DS concentration on the performance, but also that of the FS is varied to maintain equal driving force at different absolute concentrations. Experiments with clean water as feed reveal a flux increase at higher osmotic pressure. When high product purities and thus low reverse salt fluxes are required, operation at lower DS concentrations is preferred. Whey as FS induces severe initial flux decline due to instantaneous protein fouling of the membrane. This is mostly due to reversible fouling, and to a smaller extent to irreversible fouling. Concentration factors in the range of 1.2–1.3 are obtained. When 0.5 M NaCl is added to whey as FS, clearly lower fluxes are obtained due to more severe concentration polarization. Multiple runs over longer times show though that irreversible fouling is fully suppressed due to salting in/out effects and flux decline is the result of reversible fouling only. Full article

An osmotically driven membrane process was proposed for seawater pretreatment in a multi-stage flashing (MSF) thermal plant. Brine reject from the MSF plant was the draw solution (DS) in the forward osmosis (FO) process in order to reduce chemical use. The purpose of FO is the removal of divalent ions from seawater prior the thermal desalination. In this study, seawater at 80 g/L and 45 g/L concentrations were used as the brine reject and seawater, respectively. The temperature of the brine reject was 40 °C and of seawater was 25 °C. Commercial thin-film composite (TFC) and cellulose triacetate (CTA) membranes were evaluated for the pretreatment of seawater in the FO and the pressure-assisted FO (PAFO) processes. Experimental results showed 50% more permeation flux by increasing the feed pressure from 1 to 4 bar, and permeation flux reached 16.7 L/m²h in the PAFO process with a TFC membrane compared to 8.3 L/m²h in the PAFO process with CTA membrane. TFC membrane experienced up to 15% reduction in permeation flux after cleaning with DI water while permeation flux reduction in the CTA membrane was >6%. The maximum recovery rate was 11.5% and 8.8% in the PAFO process with TFC and CTA membrane, respectively. The maximum power consumption for the pretreatment of seawater was 0.06 kWh/m³ and 0.1 kWh/m³ for the PAFO process with a TFC and CTA membrane, respectively. Full article

Forward osmosis (FO) is an important desalination method to produce potable water. It was also used to treat different wastewater streams, including industrial as well as municipal wastewater. Though FO is environmentally benign, energy intensive, and highly efficient; it still suffers from four types of fouling namely: organic fouling, inorganic scaling, biofouling and colloidal fouling or a combination of these types of fouling. Membrane fouling may require simple shear force and physical cleaning for sufficient recovery of membrane performance. Severe fouling may need chemical cleaning, especially when a slimy biofilm or severe microbial colony is formed. Modification of FO membrane through introducing zwitterionic moieties on the membrane surface has been proven to enhance antifouling property. In addition, it could also significantly improve the separation efficiency and longevity of the membrane. Zwitterion moieties can also incorporate in draw solution as electrolytes in FO process. It could be in a form of a monomer or a polymer. Hence, this review comprehensively discussed several methods of inclusion of zwitterionic moieties in FO membrane. These methods include atom transfer radical polymerization (ATRP); second interfacial polymerization (SIP); coating and in situ formation. Furthermore, an attempt was made to understand the mechanism of improvement in FO performance by zwitterionic moieties. Finally, the future prospective of the application of zwitterions in FO has been discussed. Full article