Search Results (32)

This study investigates the triboelectric performance of nanogenerators based on copy paper (CP) and barium titanate (BTO) with varying concentrations (0%, 5%, 10%, 15%, and 20%). BTO was coated onto the paper surface via screen-printing, significantly enhancing the triboelectric properties. Results showed that as the BTO concentration increased, the output performance improved, with optimal performance observed at 15% BTO. At this concentration, the nanogenerator produced an output of 103 V and 3.6 µA. The CP/BTO nanogenerator demonstrated stable performance over 57,600 cycles at 4 Hz frequency and 40 N applied force, indicating excellent durability. The device attained a maximum power density of 32.4 µWcm², highlighting the efficiency improvement through BTO integration. Various parameters including BTO concentration, applied force, and frequency were studied to optimize device performance. The CP/BTO device successfully powered 60 LEDs and a calculator, demonstrating its potential for practical energy harvesting applications. This research presents a promising approach for developing low-cost, environmentally friendly power-generating systems for wearable and portable devices. Full article

The thin-film lithium niobate (TFLN)-based electro-optic (EO) modulator is one of the most important devices for optical communications in terms of the advantages of low voltages and large bandwidth. However, the large size of devices limits their applicability in large-scale integrated optical systems, posing a key challenge in maintaining performance advantages under restricted design space. In this paper, we propose a novel TFLN modulator on a quartz substrate incorporating barium titanate (BaTiO₃, BTO) as the cladding material. The device is designed with silicon–lithium niobate (Si-LN) hybrid waveguides for operation at a wavelength of 1.55 µm. After theoretical analysis and parameter optimization, the proposed 10 mm long modulator demonstrates high-efficiency modulation, featuring a low half-wave voltage-length product of 1.39 V·cm, a broad 3 dB EO bandwidth of 152 GHz, and low optical loss. This theoretical model provides a novel design solution for TFLN modulators on quartz substrates. Moreover, it is a promising solution for enhancing the integration of photonic devices on the TFLN platform. Full article

An Integrated Process Intensification (IPI) technology-based roadmap is proposed for the utilization of renewables (water, air and biomass/unavoidable waste) in the small-scale distributed production of the following primary products: electricity, H₂, NH₃, HNO₃ and symbiotic advanced (SX) fertilizers with CO₂ mineralization capacity to achieve negative CO₂ emission. Such a production platform is an integrated intensified biorefinery (IIBR), used as an alternative to large-scale centralized production which relies on green electricity and CCUS. Hence, the capacity and availability of the renewable biomass and unavoidable waste were examined. The critical elements of the IIBR include gasification/syngas production; syngas cleaning; electricity generation; and the conversion of clean syngas (which contains H₂, CO, CH₄, CO₂ and N₂) to the primary products using nonthermal plasma catalytic reactors with in situ NH₃ sequestration for SA fertilizers. The status of these critical elements is critically reviewed with regard to their techno-economics and suitability for industrial applications. Using novel gasifiers powered by a combination of CO₂, H₂O and O₂-enhanced air as the oxidant, it is possible to obtain syngas with high H₂ concentration suitable for NH₃ synthesis. Gasifier performances for syngas generation and cleaning, electricity production and emissions are evaluated and compared with gasifiers at 50 kWe and 1–2 MWe scales. The catalyst and plasma catalytic reactor systems for NH₃ production with or without in situ reactive sequestration are considered in detail. The performance of the catalysts in different plasma reactions is widely different. The high intensity power (HIP) processing of perovskite (barium titanate) and unary/binary spinel oxide catalysts (or their combination) performs best in several syntheses, including NH₃ production, NO_x from air and fertigation fertilizers from plasma-activated water. These catalysts can be represented as BaTi_1−vO_3−x{#}_yN_z (black, piezoelectric barium titanate, bp-{BTO}) and M⁽¹⁾_3−jM⁽²⁾_kO_4−m{#}_nN_r/SiO₂ (unary (k = 0) or a binary (k > 0) silane-coated SiO₂-supported spinel oxide catalyst, denoted as M/Si = X) where {#} infers oxygen vacancy. HIP processing in air causes oxygen vacancies, nitrogen substitution, the acquisition of piezoelectric state and porosity and chemical/morphological heterogeneity, all of which make the catalysts highly active. Their morphological evaluation indicates the generation of dust particles (leading to porogenesis), 2D-nano/micro plates and structured ribbons, leading to quantum effects under plasma catalytic synthesis, including the acquisition of high-energy particles from the plasma space to prevent product dissociation as a result of electron impact. M/Si = X (X > 1/2) and bp-{BTO} catalysts generate plasma under microwave irradiation (including pulsed microwave) and hence can be used in a packed bed mode in microwave plasma reactors with plasma on and within the pores of the catalyst. Such reactors are suitable for electric-powered small-scale industrial operations. When combined with the in situ reactive separation of NH₃ in the so-called Multi-Reaction Zone Reactor using NH₃ sequestration agents to create SA fertilizers, the techno-economics of the plasma catalytic synthesis of fertilizers become favorable due to the elimination of product separation costs and the quality of the SA fertilizers which act as an artificial root system. The SA fertilizers provide soil fertility, biodiversity, high yield, efficient water and nutrient use and carbon sequestration through mineralization. They can prevent environmental damage and help plants and crops to adapt to the emerging harsh environmental and climate conditions through the formation of artificial rhizosphere and rhizosheath. The functions of the SA fertilizers should be taken into account when comparing the techno-economics of SA fertilizers with current fertilizers. Full article

Flexible electronics show wide application prospects in electronic skin, health monitoring, and human–machine interfacing. As an essential part of flexible electronics, flexible pressure sensors have become a compelling subject of academic research. There is an urgent need to develop piezoelectric sensors with high sensitivity and stability. In this work, the high flexibility of polylactic acid (PLA) film and the excellent ferroelectric properties and high dielectric constant of tetragonal barium titanate (BTO) led to their use as filling materials to fabricate flexible piezoelectric composite films by spinning coating. PLA is used to produce flexible binding substrates, and BTO is added to the composite to enhance its electrical output by improving its piezoelectric performance. The peak output voltage of the PLA/BTO tetragonal piezoelectric film is 22.57 V, and the maximum short-circuit current was 3041 nA. Durability tests showed that during 40,000 s of continuous operation, in the range of 15~120 kPa, the linear relationship between pressure and the film was excellent, the sensitivity for the output voltage is 0.176 V/kPa, and the output current is 27.77 nA/kPa. The piezoelectric pressure sensor (PPS) also enables accurate motion detection, and the extensive capabilities of the PENG highlight its potential in advancing motion sensing and human–computer interactions. Full article

Barium titanate (BaTiO₃, BTO), conventionally used for dielectric and ferroelectric applications, has been assessed for biomedical applications, such as its utilization as a radiopacifier in mineral trioxide aggregates (MTA) for endodontic treatment. In the present study, BTO powders were prepared using the sol-gel process, followed by calcination at 400–1100 °C. The X-ray diffraction technique was then used to examine the as-prepared powders to elucidate the effect of calcination on the phase composition and crystalline size of BTO. Calcined BTO powders were then used as radiopacifiers for MTA. MTA-like cements were investigated to determine the optimal calcination temperature based on the radiopacity and diametral tensile strength (DTS). The experimental results showed that the formation of BTO phase was observed after calcination at temperatures of 600 °C and above. The calcined powders were a mixture of BaTiO₃ phase with residual BaCO₃ and/or Ba₂TiO₄ phases. The performance of MTA-like cements with BTO addition increased with increasing calcination temperature up to 1000 °C. The radiopacity, however, decreased after 7 days of simulated oral environmental storage, whereas an increase in DTS was observed. Optimal MTA-like cement was obtained by adding 40 wt.% 1000 °C-calcined BTO powder, with its resulting radiopacity and DTS at 4.83 ± 0.61 mmAl and 2.86 ± 0.33 MPa, respectively. After 7 days, the radiopacity decreased slightly to 4.69 ± 0.51 mmAl, accompanied by an increase in DTS to 3.13 ± 0.70 MPa. The optimal cement was biocompatible and verified using MG 63 and L929 cell lines, which exhibited cell viability higher than 95%. Full article

Hydrodynamic pressure sensors offer an auxiliary approach for ocean exploration by unmanned underwater vehicles (UUVs). However, existing hydrodynamic pressure sensors often lack the ability to monitor subtle hydrodynamic stimuli in deep-sea environments. In this study, we present the development of a deep-sea hydrodynamic pressure sensor (DSHPS) capable of operating over a wide range of water depths while maintaining exceptional hydrodynamic sensing performance. The DSHPS device was systematically optimized by considering factors such as piezoelectric polyvinylidene fluoride–trifluoroethylene/barium titanate [P(VDF-TrFE)/BTO] nanofibers, electrode configurations, sensing element dimensions, integrated circuits, and packaging strategies. The optimized DSHPS exhibited a remarkable pressure gradient response, achieving a minimum pressure difference detection capability of approximately 0.11 Pa. Additionally, the DSHPS demonstrated outstanding performance in the spatial positioning of dipole sources, which was elucidated through theoretical charge modeling and fluid–structure interaction (FSI) simulations. Furthermore, the integration of a high Young’s modulus packaging strategy inspired by fish skull morphology ensured reliable sensing capabilities of the DSHPS even at depths of 1000 m in the deep sea. The DSHPS also exhibited consistent and reproducible positioning performance for subtle hydrodynamic stimulus sources across this wide range of water depths. We envision that the development of the DSHPS not only enhances our understanding of the evolutionary aspects of deep-sea canal lateral lines but also paves the way for the advancement of artificial hydrodynamic pressure sensors. Full article

Piezoelectric thin films are extensively used as sensing or actuating layers in various micro-electromechanical systems (MEMS) applications. However, most piezoelectrics are stiff ceramics, and current polymer piezoelectrics are not compatible with microfabrication due to their low Curie Temperature. Recent polymer-composite piezoelectrics have gained interest but can be difficult to pattern. Photodefinable piezoelectric films could resolve these challenges by reducing the manufacturability steps by eliminating the etching process. But they typically have poor resolution and thickness properties. This study explores methods of enhancing the manufacturability of piezoelectric composite films by optimizing the process parameters and synthesis of SU-8 piezo-composite materials. Piezoelectric ceramic powders (barium titanate (BTO) and lead zirconate titanate (PZT)) were integrated into SU-8, a negative epoxy-based photoresist, to produce high-resolution composites in a non-cleanroom environment. I-line (365 nm) light was used to enhance resolution compared to broadband lithography. Two variations of SU-8 were prepared by thinning down SU-8 3050 and SU-8 3005. Different weight percentages of the piezoelectric powders were investigated: 5, 10, 15 and 20 wt.% along with varied photolithography processing parameters. The composites’ transmittance properties were characterized using UV-Vis spectroscopy and the films’ crystallinity was determined using X-ray diffraction (XRD). The 0–3 SU-8/piezo composites demonstrated resolutions < 2 μm while maintaining bulk piezoelectric coefficients d₃₃ > 5 pm V⁻¹. The films were developed with thicknesses >10 μm. Stacked layers were achieved and demonstrated significantly higher d₃₃ properties. Full article

With the advent of the Internet of Things, self-powered wearable sensors have become increasingly prevalent in our daily lives. The utilization of piezoelectric composites to harness and sense surrounding mechanical vibrations has been extensively investigated during the last decades. However, the poor interface compatibility between ceramics nanofillers and polymers matrix, as well as low piezoelectric performance, still serves as a critical challenge. In this work, we employed Di(dioctylpyrophosphato) ethylene titanate (DET) as the coupling agent for modifying barium titanate (BTO) nanofillers. Compared to the BTO/PVDF counterpart, the DET-BTO/PVDF nanofibers exhibit an augmented content of piezoelectric β phase (~85.7%) and significantly enhanced stress transfer capability. The piezoelectric coefficient (d₃₃) is up to ~40 pC/N, which is the highest value among reported BTO/PVDF composites. The piezoelectric energy harvesters (PEHs) present benign durability and attain a high instantaneous power density of 276.7 nW/cm² at a matched load of 120 MΩ. Furthermore, the PEHs could sense various human activities, with the sensitivity as high as 0.817 V/N ranging from 0.05–0.1 N. This work proposes a new strategy to boosting the piezoelectric performance of PVDF-based composites via DET-doping ceramics nanoparticles, and in turn show significantly improved energy harvesting and sensing capability. Full article

Mineral trioxide aggregates (MTA) are commonly used as endodontic filling materials but suffer from a long setting time and tooth discoloration. In the present study, the feasibility of using barium titanate (BTO) for discoloration and a calcium chloride (CaCl₂) solution to shorten the setting time was investigated. BTO powder was prepared using high-energy ball milling for 3 h, followed by sintering at 700–1300 °C for 2 h. X-ray diffraction was used to examine the crystallinity and crystalline size of the as-milled and heat-treated powders. MTA-like cements were then prepared using 20–40 wt.% BTO as a radiopacifier and solidified using a 0–30% CaCl₂ solution. The corresponding radiopacity, diametral tensile strength (DTS), initial and final setting times, and discoloration performance were examined. The experimental results showed that for the BTO powder prepared using a combination of mechanical milling and heat treatment, the crystallinity and crystalline size increased with the increasing sintering temperature. The BTO sintered at 1300 °C (i.e., BTO-13) exhibited the best radiopacity and DTS. The MTA-like cement supplemented with 30% BTO-13 and solidified with a 10% CaCl₂ solution exhibited a radiopacity of 3.68 ± 0.24 mmAl and a DTS of 2.54 ± 0.28 MPa, respectively. In the accelerated discoloration examination using UV irradiation, the color difference was less than 1.6 and significantly lower than the clinically perceptible level (3.7). This novel MTA exhibiting a superior color stability, shortened setting time, and excellent biocompatibility has potential for use in endodontic applications. Full article

Lead-free piezoelectric materials are essential for our healthy future but offer lower performance than lead-based materials. Different material combinations are explored to improve the performance of lead-free materials. By filling the UV light curable photopolymer resin with 30 vol.% lead-free piezoelectric ceramics and with up to 0.4 wt.% conductive nanofillers, thin and flexible piezoelectric 0-0-3 composites are formed. Two particle sizes of Potassium Sodium Niobate (KNN) and Barium Titanate (BTO) ceramics were used with four conductive nanofillers: Graphene Nanoplatelets (GNPs), Multi-Walled Carbon Nanotubes (MWCNTs), and two types of Graphene Oxide (GO). Resulting high viscosity suspensions are tape-cast in a mold as thin layers and subsequently exposing them to UV light, piezoelectric composite sensors are formed in 80 s. Even low nanofiller concentrations increase relative permittivities, however, they strongly reduce curing depth and increase undesirable dielectric losses. Non-homogeneous dispersion of nanofillers is observed. In total, 36 different compositions were mixed and characterized. Only six selected material compositions were investigated further by measuring mechanical, dielectric, and piezoelectric properties. Results show KNN composite performance as piezoelectric sensors is almost six times higher than BTO composite performance. Full article

Space charge accumulation greatly influences the dielectric performance of epoxy composites under high voltage. It has been reported that nano-fillers can suppress the charge accumulation in the bulk of insulation materials. However, it is still unclear how the nano-fillers influence the charge distribution at the interface between the filler and polymeric matrix. In this work, the dielectric properties and the local dynamic charge mobility behavior at the interface of barium titanate/epoxy resin (BTO/EP) composites were investigated from both bulk and local perspectives based on the macroscopic test techniques and in-situ Kelvin probe force microscopy (KPFM) methods. Charge injection and dissipation behavior exhibited significant discrepancies at different interfaces. The interface between BTO and epoxy is easy to accumulates a negative charge, and nanoscale BTO (n-BTO) particles introduces deeper traps than microscale BTO (m-BTO) to inhibit charge migration. Under the same bias condition, the carriers are more likely to accumulate near the n-BTO than the m-BTO particles. The charge dissipation rate at the interface region in m-BTO/EP is about one order of magnitude higher than that of n-BTO/EP. This work offers experimental support for understanding the mechanism of charge transport in dielectric composites. Full article

Peroxymonosulfate (PMS) plays an important role in the advanced oxidation process for environmental remediation. In this study, barium titanate (BTO) piezocatalyst was selected for the activation of PMS driven by ultrasonic power. The degradation of Rhodamine B (RhB) by BTO single component, PMS single component, and BTO/PMS double components were investigated. The results indicated that PMS can be efficiently activated by BTO under an ultrasound with an RhB degradation rate of 98% within 20 min. The ultrasound not only promoted the activation of the PMS itself, but the surface charge carriers of BTO induced by the ultrasound also contributed to the activation of PMS. ·O₂⁻, ·OH, and ·SO₄⁻ radicals were found to be the main active species that participated in the reaction. In order to verify the reaction’s environmental applicability, amoxicillin (AMX) as a typical environmental pollutant was studied. BTO/PMS displayed 80% removal efficiency of AMX, and the products generated were less toxic as demonstrated by eco-toxicity comparison. This work provides a promising strategy to improve the utilization of ultrasonic energy and apply it to the field of environmental pollutants treatment. Full article

Core−shell nanocomposites comprising barium titanate, BaTiO₃ (BTO), and poly(methyl methacrylate) (PMMA) chains grafted from its surface with varied grafting densities were prepared. BTO nanocrystals are high-k inorganic materials, and the obtained nanocomposites exhibit enhanced dielectric permittivity, as compared to neat PMMA, and a relatively low level of loss tangent in a wide range of frequencies. The impact of the molecular dynamics, structure, and interactions of the BTO surface on the polymer chains was investigated. The nanocomposites were characterized by broadband dielectric and vibrational spectroscopies (IR and Raman), transmission electron microscopy, differential scanning calorimetry, and nuclear magnetic resonance. The presence of ceramic nanoparticles in core–shell composites slowed down the segmental dynamic of PMMA chains, increased glass transition temperature, and concurrently increased the thermal stability of the organic part. It was also evidenced that, in addition to segmental dynamics, local β relaxation was affected. The grafting density influenced the self-organization and interactions within the PMMA phase, affecting the organization on a smaller size scale of polymeric chains. This was explained by the interaction of the exposed surface of nanoparticles with polymer chains. Full article

Piezoelectric energy harvesters are appealing for the improvement of wearable electronics, owing to their excellent mechanical and electrical properties. Herein, screen-printed piezoelectric nanogenerators (PENGs) are developed from triethoxy(octyl)silane-coated barium titanate/polyvinylidene fluoride (TOS-BTO/PVDF) nanocomposites with excellent performance based on the important link between material, structure, and performance. In order to minimize the effect of nanofiller agglomeration, TOS-coated BTO nanoparticles are anchored onto PVDF. Thus, composites with well-distributed TOS-BTO nanoparticles exhibit fewer defects, resulting in reduced charge annihilation during charge transfer from inorganic nanoparticles to the polymer. Consequently, the screen-printed TOS-BTO/PVDF PENG exhibits a significantly enhanced output voltage of 20 V, even after 7500 cycles, and a higher power density of 15.6 μW cm⁻², which is 200 and 150% higher than those of pristine BTO/PVDF PENGs, respectively. The increased performance of TOS-BTO/PVDF PENGs is due to the enhanced compatibility between nanofillers and polymers and the resulting improvement in dielectric response. Furthermore, as-printed devices could actively adapt to human movements and displayed excellent detection capability. The screen-printed process offers excellent potential for developing flexible and high-performance piezoelectric devices in a cost-effective and sustainable way. Full article

Ferroelectric property that induces electrocaloric effect was investigated in Ba(Ge_xTi_1−x)O₃ ceramics, known as BTGx. X-ray diffraction analysis shows pure perovskite phases in tetragonal symmetry compatible with the P4mm (No. 99) space group. Dielectric permittivity exhibits first-order ferroelectric-paraelectric phase transition, confirmed by specific heat measurements, similar to that observed in BaTiO₃ (BTO) crystal. Curie temperature varies weakly as a function of Ge-content. Using the direct and indirect method, we confirmed that the adiabatic temperature change ΔT reached its higher value of 0.9 K under 8 kV/cm for the composition BTG6, corresponding to an electrocaloric responsivity ΔT/ΔE of 1.13 × 10⁻⁶ K.m/V. Such electrocaloric responsivity significantly exceeds those obtained so far in other barium titanate-based lead-free electrocaloric ceramic materials. Energy storage investigations show promising results: stored energy density of ~17 mJ/cm³ and an energy efficiency of ~88% in the composition BTG5. These results classify the studied materials as candidates for cooling devices and energy storage applications. Full article