Search Results (5)

This work studies the antimicrobial activity of benzyldimethyldodecyl ammonium chloride (BDMDAC)-coated microparticles with distinct morphological structures. Functionalized microparticles were prepared by the layer-by-layer (LbL) self-assembly technique on hydroxyapatite (Hap), calcium carbonate (CaCO₃) and glass beads (GB) cores. All particles were characterized, before and after functionalization, by Fourier-Transform Infrared Spectroscopy (FTIR), Brunner–Emmett–Teller (BET) and Scanning Electron Microscopy (SEM) analyses. Antimicrobial activity was tested against planktonic Pseudomonas fluorescens. Planktonic bacteria were exposed to 100 mg/L, 200 mg/L and 400 mg/L of BDMDAC-coated microparticles for 240 min. This strategy promoted a complete bacteria reduction at 200 mg/L for Hap microparticles after 240 min. No release of biocide was detected through HPLC analyses during 2 weeks, suggesting that bacteria inactivation may be attributed to a contact killing mechanism. Full article

Current dental adhesives lack antibacterial properties. This study aimed to explore the effect of incorporating benzyldimethyldodecyl ammonium chloride (BDMDAC) on the degree of conversion, contact angle, ultimate tensile strength (UTS), microtensile bond strength (µTBS), cytotoxicity, antibacterial and bonding performance after artificial aging. A dental adhesive was doped with BDMDAC in the concentration range of 1–5 wt.%. For antibacterial assays, the BDMDAC compound was subject to planktonic cells of Streptococcus mutans. Then, after incorporation into the dental adhesive, an S. mutans biofilm model was used to grow 48 h-mature biofilms. The biofilms grown over the formulated materials were assessed by colony-forming unit (CFU) counting assay and fluorescence microscopy staining. In addition, the cytotoxicity was evaluated. Samples were subjected to 10,000 thermal cycles for aging and evaluated by UTS, µTBS, and CFU. Incorporating BDMDAC did not increase the cytotoxicity or change the physical properties when the mass fraction of the BDMDAC was 1–5 wt.%. The UTS of BDMDAC-doped adhesives was not impaired immediately or over time. A significant bacterial reduction was obtained for the mass fraction of the BDMDAC greater than 3 wt.%. However, the BDMDAC-doped adhesives did not offer an antibacterial effect after artificial aging. The overall results indicate that the BDMDAC strategy has the potential to control of microbial growth of cariogenic planktonic cells and biofilms. However, other new technological approaches are needed to overcome the deleterious effect of BDMDAC release over time such as those based on the principle of drug delivery systems whereby the BDMDAC is transported on microparticles or core shells, providing tangible benefits to oral health over time. Full article

Biofilm control is mainly based on chemical disinfection, without a clear understanding of the role of the biocides and process conditions on biofilm removal. This study aims to understand the effects of a biocide (benzyldimethyldodecyl ammonium chloride—BDMDAC) and mechanical treatment (an increase of shear stress -${\tau }_w$) on single- and dual-species biofilms formed by Bacillus cereus and Pseudomonas fluorescens on high-density polyethene (HDPE). BDMDAC effects were initially assessed on bacterial physicochemical properties and initial adhesion ability. Then, mature biofilms were formed on a rotating cylinder reactor (RCR) for 7 days to assess the effects of chemical and mechanical treatments, and the combination of both on biofilm removal. The results demonstrated that the initial adhesion does not predict the formation of mature biofilms. It was observed that the dual-species biofilms were the most susceptible to BDMDAC exposure. The exposure to increasing ${\tau }_w$ emphasised the mechanical stability of biofilms, as lower values of ${\tau }_w$(1.66 Pa) caused high biofilm erosion and higher ${\tau }_w$ values (17.7 Pa) seem to compress the remaining biofilm. In general, the combination of BDMDAC and the mechanical treatment was synergic in increasing biofilm removal. However, these were insufficient to cause total biofilm removal (100%; an average standard deviation of 11% for the method accuracy should be considered) from HDPE. Full article

Biocides are frequently used to control sulfate-reducing bacteria (SRB) in biofouling. The increasing restrictions of environmental regulations and growing safety concerns on the use of biocides result in efforts to minimize the amount of biocide use and develop environmentally friendly biocides. In this study, the antimicrobial activity and corrosion inhibition effect of a low-toxic alternative biocide, benzyldimethyldodecylammonium chloride (BDMDAC), on a 304 stainless steel substrate immersed in a Desulfovibrio desulfuricans (D. desulfuricans)-inoculated medium was examined. Potentiodynamic polarization curves were used to analyze corrosion behavior. Biofilm formation and corrosion products on the surfaces of 304 stainless steel coupons were examined using scanning electron microscopy (SEM), energy-dispersive X-ray spectrum, and confocal laser scanning microscopy (CLSM). Results demonstrated that this compound exhibited satisfactory results against microbial corrosion by D. desulfuricans. The corrosion current density and current densities in the anodic region were lower in the presence of BDMDAC in the D. desulfuricans-inoculated medium. SEM and CLSM analyses revealed that the presence of BDMDAC mitigated formation of biofilm by D. desulfuricans. Full article

Cationic polyacrylamides have been employed widely to improve sludge dewatering performance, but the cationic units are randomly distributed in the molecular chain, which restricts the further enhancement of dewaterability. Common template technology to prepare block copolymers requiring a huge number of templates reduces the polymer purity and molecular weight. Here, we adopted the surface-active monomer benzyl dimethyl 2-(methacryloyloxy)ethyl ammonium chloride (BDMDAC) to synthesize cationic microblocky polyacrylamide initiated by ultrasound. The reactivity ratio of monomers suggested that novel cationic monomer BDMDAC had higher homopolymerization ability, and was thus more prone to forming a microblock structure. The statistical analysis of sequence-length distribution indicated that the number and length of cationic segments increased in the PAB molecules. In addition, the characteristic results of Fourier transform infrared (FTIR), proton nuclear magnetic resonance (¹H NMR), and thermogravimetric analysis (TGA) provided evidence for the synthesis of copolymer with cationic microblocks. Finally, the results of dewatering tests demonstrated that sludge dewaterability was greatly improved by adding the synthesized novel flocculants, and the sludge-specific resistance to filtration, filter cake moisture content and residual turbidity all reached a minimum (68.7%, 5.4 × 1012 m·kg⁻¹, and 2.6 NTU, respectively) at 40 mg·L⁻¹. The PAB flocs were large, compact, difficult to break, and easy to regrow. Furthermore, PAB was more effective in the removal of protein from soluble extracellular polymeric substances (SEPSs). In summary, this study provides a novel solution to synthesize cationic microblock polyacrylamide for improving sludge dewatering. Full article