We are pleased to invite you to read the top 10 cited papers from 2022 in Materials (ISSN: 1996-1944) in the Section “Metals and Alloys”. The paper list is as follows:

1. “Magnesium-Based Alloys Used in Orthopedic Surgery”
by Iulian Antoniac, Marian Miculescu, Veronica Mănescu (Păltânea), Alexandru Stere, Pham Hong Quan, Gheorghe Păltânea, Alina Robu and Kamel Earar
Materials 2022, 15(3),1148; https://doi.org/10.3390/ma15031148
Available online: https://www.mdpi.com/1996-1944/15/3/1148

2. “Modeling Dynamic Recrystallization Behavior in a Novel HIPed P/M Superalloy during High-Temperature Deformation”
by Qiu-Mei Yang, Yong-Cheng Lin, Ming-Song Chen and Zi-Jian Chen
Materials 2022, 15(11), 4030; https://doi.org/10.3390/ma15114030
Available online: https://www.mdpi.com/1996-1944/15/11/4030

3. “Effect of SiC Nanoparticles on AZ31 Magnesium Alloy”
by Murugan Subramani, Song-Jeng Huang and Konstantin Borodianskiy
Materials 2022, 15(3), 1004; https://doi.org/10.3390/ma15031004
Available online: https://www.mdpi.com/1996-1944/15/3/1004

4. “Materials Engineering for Flexible Metallic Thin Film Applications”
by Megan J. Cordill, Patrice Kreiml and Christian Mitterer
Materials 2022, 15(3), 926; https://doi.org/10.3390/ma15030926
Available online: https://www.mdpi.com/1996-1944/15/3/926

5. “Electrochemical and In Vitro Biological Evaluation of Bio-Active Coatings Deposited by Magnetron Sputtering onto Biocompatible Mg-0.8Ca Alloy”
by Ana-Iulia Bița, Iulian Antoniac, Marian Miculescu, George E. Stan, Lucia Leonat, Aurora Antoniac, Bujor Constantin and Norin Forna
Materials 2022, 15(9), 3100; https://doi.org/10.3390/ma15093100
Available online: https://www.mdpi.com/1996-1944/15/9/3100

6. “Fluoride Treatment and In Vitro Corrosion Behavior of Mg-Nd-Y-Zn-Zr Alloys Type”
by Pham Hong Quan, Iulian Antoniac, Florin Miculescu, Aurora Antoniac, Veronica Manescu (Păltânea), Alina Robu, Ana-Iulia Bița, Marian Miculescu, Adriana Saceleanu, Alin Dănuț Bodog et al.
Materials 2022, 15(2), 566; https://doi.org/10.3390/ma15020566
Available online: https://www.mdpi.com/1996-1944/15/2/566

7. “Designing for Shape Memory in Additive Manufacturing of Cu–Al–Ni Shape Memory Alloy Processed by Laser Powder Bed Fusion”
by Mikel Pérez-Cerrato, Itziar Fraile, José Fernando Gómez-Cortés, Ernesto Urionabarrenetxea, Isabel Ruiz-Larrea, Iban González, María Luisa Nó, Nerea Burgos and Jose M. San Juan
Materials 2022, 15(18), 6284; https://doi.org/10.3390/ma15186284
Available online: https://www.mdpi.com/1996-1944/15/18/6284

8. “Microstructural Characterization of Additively Manufactured Metal Components Using Linear and Nonlinear Ultrasonic Techniques”
by Seong-Hyun Park, Sungho Choi, Dong-Gi Song and Kyung-Young Jhang
Materials 2022, 15(11),3876; https://doi.org/10.3390/ma15113876
Available online: https://www.mdpi.com/1996-1944/15/11/3876

9. “Hot Isostatic Pressing for Fatigue Critical Additively Manufactured Ti-6Al-4V”
by Terrence P. Moran, Patricio E. Carrion, Seungjong Lee, Nima Shamsaei, Nam Phan and Derek H. Warner
Materials 2022, 15(6), 2051; https://doi.org/10.3390/ma15062051
Available online: https://www.mdpi.com/1996-1944/15/6/2051

10. “Effects of Shot Peening and Cavitation Peening on Properties of Surface Layer of Metallic Materials—A Short Review”
by Aleksander Świetlicki, Mirosław Szala and Mariusz Walczak
Materials 2022, 15(7), 2476; https://doi.org/10.3390/ma15072476
Available online: https://www.mdpi.com/1996-1944/15/7/2476