Next Article in Journal
Decolorization of Melanoidin Using Sono–Fenton and Photo–Fenton Processes
Next Article in Special Issue
Anaerobic Treatment of Food Waste with Biogas Recirculation under Psychrophilic Temperature
Previous Article in Journal
An Improved Design for Flow Conditioning in Waste Water Pipes
Previous Article in Special Issue
Computational Modelling on Gasification Processes of Municipal Solid Wastes Including Molten Slag
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Conversion of Waste Synthesis Gas to Desalination Catalyst at Ambient Temperatures

by
David D. J. Antia
DCA Consultants Ltd., The Bungalow, Castleton Farm, Falkirk FK2 8SD, UK
Waste 2023, 1(2), 426-454; https://doi.org/10.3390/waste1020026
Submission received: 30 January 2023 / Revised: 10 April 2023 / Accepted: 11 April 2023 / Published: 1 May 2023

Abstract

:
In this study, a continuous flow of a synthetic, dry, and acidic waste synthesis gas (WSG) (containing N2, H2, CO, CH4, and CO2) at ambient temperatures was first passed through a fixed bed reactor (FBR) containing halite + m-Fe0 and then a saline bubble column diffusion reactor (BCDR) containing m-Fe0. The FBR converted 47.5% of the CO + CH4 + CO2 into n-C0. Passage of the n-C0 into the BCDR resulted in the formation of the desalination catalyst (Fe0:Fe(a,b,c)@C0) + CH4 + CO + CO2 + CxHy, where 64% of the feed n-C0 was converted to gaseous products. The desalination pellets can remove >60% of the water salinity without producing a reject brine or requiring an external energy source. The gaseous products from the BCDR included: CxHy (where x < 6), CO, CO2, and H2.

1. Introduction

In this study, a continuous flow of a synthetic waste synthesis gas (SWSG) was used to produce a desalination catalyst ((Fe0:Fe(a,b,c)@C0)n polymer). The process involved redox reactions [1,2,3] and used both halite and FexOyHz species as solid solutions [4,5,6]. The redox reactions operated at normal temperatures and pressures (NTP). The process required the presence of a fixed bed reactor (FBR) containing halite and a saline bubble column diffusion reactor (BCDR) containing m-Fe0 (Route 1). The passage of SWSG (containing N2, H2, CO, CH4, and CO2) sequentially through a FBR and then a BCDR converted 9.2% of the CO + CH4 to C0 + CO2 (with 53% CO2 selectivity) [3]. This C0 formed an Fe0:Fe(b)@C0 polymer within the BCDR. The placement of the polymer pellets in saline water resulted in between 30% and 60% desalination. The desalination is a pseudo-zero order reaction [3]. This study identified an alternative manufacturing route for the production of these desalination pellets. This route is termed Route 2.
Synthesis gas (SG) is a gas containing hydrogen and carbon monoxide (Figure 1). It can contain one or more of the following: N2, CO2, CH4, CxHy, and CxHyOz. SG is formed by the following processes: (i) partial oxidation [7,8]; (ii) wet reforming [9,10,11]; (iii) dry reforming [12,13,14]; (iv) autothermal reforming [15,16]; (v) hydrothermal gasification [17,18,19]; (vi) pyrolysis, or partial combustion, carbonization, or gasification [20,21,22,23]. SG can be manufactured from any carbonaceous (organic) material, including municipal waste.
SG is traditionally used as: (i) fuel gas for domestic/municipal/industrial applications (town gas) [24,25]; (ii) feedstock for the manufacture of synthetic fuels (e.g., gas-to-liquid (GTL) processes, including Fischer–Tropsch (FT) production of synthetic natural gas [26,27,28,29], transport fuels [30,31,32,33], waxes [34,35,36,37], oxygenates [38,39,40], gas-to-methanol [41,42,43], and petrochemicals); (iii) feedstock for the manufacture of fertilizers [44,45]; (iv) feedstock for “green” power stations [46,47]; (v) a source of hydrogen gas [48,49].
The term “waste synthesis gas” (WSG) is used to describe a SG [50] produced from the processing of municipal waste (e.g., patents KR101484919B1; KR101434246B1; AT516178A4). WSG typically contains 30–60% N2 plus a mixture of H2O, H2, CO, N2, CO2, CH4, CxHy, and CxHyOz. There are >140 patents that specifically address the formation and use of WSG (e.g., patent specifications KR101484919B1; KR101482993B1; HU0800209A2; RU2459860C2; AU2009274418B2). The feedstock, SG components, and end products are summarized in Figure 1. SG can be produced over the temperature range 370 K to 2500 K. The CO:CO2 ratio in the WSG increases as its formation temperature increases, and it decreases as the oxidant (e.g., O2):carbon ratio increases. A medium-to-high-temperature SG will typically contain a CO:CO2 ratio of >1:1. A low-temperature SG (e.g., <1000 K) may contain a ratio of <0.3:1.

1.1. Desalination Using ZVI and Iron Polymers (TRL Status)

In 2008, US patent US8636906B2 established that functionalized Fe3O4, Fe0, Fe(OH)x, or FeOOH could partially desalinate saline water. In 2010–2013, bench-top continuously stirred reactors containing Fe0 established [51,52] that it was possible to partially desalinate winter saline road runoff water. In 2013, patent GB2520775A established that it was possible to use WSG, SG (synthesis gas), N2, N2 + CO2 combined with m-Fe0, or n-Fe0 to partially desalinate water. An example analysis, which is contained in GB2520775A, established that feed water containing 23.16 g Cl L−1 + 15.41 g Na+ L−1 could produce product water containing 0.09 g Cl L−1 + 0.06 g Na+ L−1. The solid material left in the reactor (termed ZVM TP) was found to be able to partially desalinate saline water bodies.
In 2015, Spanish patent ES2598032 [53] established that n-Fe0 could be used to desalinate seawater. In 2015, an academic study established that n-Fe0-treated feed water that entered a reverse osmosis ((RO) desalination plant removed both nitrates and Cl ions [54]. In 2021, a US patent (US10919784B2) established that n-Fe0 (in the presence of an air stream) could be used to partially desalinate saline water.
The technology readiness level (TRL) for any technology can be assessed using the European Space Agency’s (ESA’s) technology readiness scale [54,55]. This scale grades technology into nine distinct groups, which are termed TRL1 to TRL9. Pilot desalination plants (built to comply with patent GB2520775A) with a technology readiness level of 7 (TRL7) have been constructed and operated.
This study considers a process variant for the manufacture of desalination pellets. It uses a reactor and a WSG feedstock that complies with GB2520775A. This alternative desalination pellet manufacturing route using SWSG is termed Route 2 in this paper. The technology readiness level (TRL) of the Route 2 pellet manufacturing process is TRL4/5. The TRL for the use of the desalination pellets to desalinate water is TRL2/3.

1.2. Past Patents

The typical WSG composition is summarized elsewhere [56]. There are around 144 patents which address the formation of WSG and its applications. The majority of these patents focus on the design and operation of the carbonization retort that produces the WSG. The following patents specifically address known potentially commercial product applications for WSG:
  • KR101484919B1 constructs the WSG to undertake one or more of the following processes: Fischer–Tropsch (FT) synthesis, methanol production, DME (dimethylether) production, and SNG (synthetic natural gas) production;
  • KR101434246B1 uses (i) a CO2 adsorption process to remove CO2 from the WSG; (ii) a pressure swing adsorption (PSA) process to separate and recover H2 by separately adsorbing CO and H2;
  • CN113471492B uses the WSG as feedstock for a Solid Oxide Fuel Cell (SOFC), which is used to generate electricity;
  • RU2459860C2 uses the WSG as FT feedstock to manufacture diesel fuel; excess gas is then used to generate power;
  • AU2009274418B2 uses the WSG as FT feedstock to manufacture transport fuel;
  • BR112014004680A2 uses the WSG to manufacture aromatics and branched alkanes to produce chemical feedstock;
  • GB2463878B catalytically removes CO and CO2 from the WSG at NTP to produce hydrocarbons and a product gas, which is depleted in CO and CO2;
  • GB2520775A uses WSG to create a desalination catalyst and desalinated water.
The KR101434246B1 process uses a PSA approach to remove hydrogen. The hydrogen is then recombined with CO to produce an ideal SG (i.e., 2H2:1 CO) for a FT process. The concept of using H2 (contained in WSF) to maintain a reducing reaction environment (while abstracting the majority of the hydrogen) does not form part of the current patent literature. In this study, the extent and location of hydrogen seepage through copper pipes (Figure 2) is considered. These observations were used to decide whether a future study (operated at higher flow volumes, and a larger reactor size) should separately recover the hydrogen in an outer annulus (Figure 3).

1.3. Technical Issues Identified in the Currently Described Desalination Pellet Manufacturing Process

The technical issues that need to be considered (for the FBR) are as follows: (i) What happens to the hydrogen? In the initial manufacturing process [3], the mass balance indicates that 16.88 H2 = 0.89 H2 is retained in the reactor and 15.99 H2 is lost. The lost hydrogen either seeps through the reactor shell (about 95% of the feed hydrogen) or is placed within the reactor in another location. (ii) What happens to the carbon? In the initial manufacturing process [3], the mass balance indicates that 3.89 CH4 + 1.22 CO = 2.56 CO2 + 0.08 C2Hx + 2.39 C. C is carbon that is not accounted for in the products. It is presumed to be present as entrained C in the product gas; x = >1).
For the BCDR, the technical issues that need to be considered are as follows: (i) Is the vuggy structure of the pellets always associated with substantial excess hydrogen generation? The mass balance for the initial manufacturing process indicates that 0.89 H2 = 12.25 H2; this change is consistent with earlier studies [57,58,59]. (ii) What happens to the carbon? The mass balance for the initial manufacturing process indicates that 1.65 CH4 + 0.99 CO + 0.08 C2Hy = 1.1 CO2 + 0.18CxHy + 2.64 C. The carbon is present as C0, CxHyOz, HCO3, or CO32−; x = >1.
Unpublished control experiments (Section 2) indicate that the presence of carbon is required to create the desalination pellets. The creation of the three products C0, CO2, and CxHy suggests that the desalination catalyst may be a by-product of an aqueous FT process.
The unresolved technical questions are as follows: (i) whether the entrained carbon particles within the feed gas entering the BCDR are important; (ii) whether the desalination catalyst manufacturing process is a FT reaction by-product. This study provides a degree of clarification for both of these issues.

1.4. Increasing the Availability of n-C0 in WSG Entering the Bubble Column Reactor

If CH4 is transformed to CO2, then the initial simple assumption is CH4 + 2H2O = CO2 + 8H+ + 8e [1]. Although this describes the overall reaction route, there are two intermediate reactions in an aqueous environment: (i) Reaction A: CH4 = C0 + 4H+ + 4e [1]; (ii) Reaction B: C0 + 2H2O = CO2 + 4H+ + 4e [1].
In this study, the halite contained within the FBR was coated with m-Fe0. This change to the process configuration in the original Route 1 study [3] was designed to increase selectivity towards Reaction A relative to Reaction B. The reactor was placed within a RPSAD environment (as defined by patent GB2470764B) to further increase the discharged product selectivity from Reaction B towards Reaction A.

1.5. Utilising the n-C0

The hydrocarbon-generating reaction occurs at ambient temperatures using FexCy sites and Fe@C0 sites. These sites are located both within the particles and on the n-Fe0 particle surfaces. This reaction belongs to the aqueous FT family of reactions [60,61,62]. In the aqueous environment, fresh sites are created by physically adsorbed n-C0 [1] and by the formation of sites associated with CO2 [63].
The products produced by these sites include [63]:
  • Oxygenated Gases: CO2, CO, and their dissolved forms (H2CO2; HCO2; CO22−; H2CO3; HCO3; CO32−);
  • Reduced Gases: CH4; C2Hx; C3Hx; C4Hx; C5Hx;
  • Carboxylic Acids: HCOO; CH3COO; C2H5COO; C3H7COO; CH2(COO)2; C2O42−;
  • Aldehydes: CH2O; C2H4O; C3H6O;
  • Alcohols: CH3OH; C2H5OH; C2H7OH.
The four insertion mechanisms proposed for product formation in a gaseous environment are the carbide, Enol, CO, and formate [64]. These insertion mechanisms, in both the aqueous and gaseous environments, appear to be similar [65].
In the aqueous environment, ZVI first reduces chloro-organics to C2H2. The C2H2 is then hydrogenated and polymerized to form CxHy and CxHyOz species [66,67]. This allows the relative efficiency of the hydrocarbon-producing reaction (Re) to be visualized using a normalizing equation of the form [67]
Re = ((Ct=0Ct=n)(Σ ni pi))/(2No)),
where ni = the number of electrons required for a stoichiometric reaction, i = the molar proportion of the reactant converted to the product, i; Ct=0 = molar concentration of the reactant at time t = 0; Ct=n = molar concentration of the reactant at time t = n; No = the number of moles of Fe0 present at time t = 0. The value of ni is constant with C2Hx species for reactions on the Fe0 surface, where Eh is <−0.0591 pH. This relative efficiency measure assumes that the sole carbon source is contained within the feed gas stream.
In 1996, a series of control experiments in which Fe0 (containing 2.4% C) was placed in water containing 12.3 mg HCO3 L−1 (at NTP) produced CxHy species at a slow rate (<2.76 × 10−7 mg CxHy g−1 Fe0 h−1) [67].
Subsequent studies in 1997 [68] and in 2018–2022 [69,70,71] sourced the hydrocarbons from carbon contained within the Fe0. Oxygenated products dominated the product suite [72]. The initial FT reactions may be:
2[C]4− + 4H2O = ((CO2)2)2− + 8H+ + 10e
((CO2)2)2− + 7H+ + 6e = CH3COO + 2H2O
((CO2)2)2− + 2H+ + 2e = 2HCOO
The first reaction is the production of an oxalate. The primary surface reaction, on the Fe surface, in water, takes the form [73]:
−[[[Fe2+]5([C4−]2)]2+]− + 4H2O = −[[[Fe2+]((CO2)2)2−]]− + 4Fe0 + 8H+ + 6e
−[[[Fe2+]((CO2)2)2−]]− + H2 + 4e = ((CO2)2)2− + FeH2
−[[[Fe2+]((CO2)2)2−]]− + 0.5H2 + 3e = ((CO2)2)2− + FeH+
The primary reaction is oxalate formation. The FeHx site is created when the oxalate is desorbed [73]. A [Fe2+[CO]2−] initiation site for hydrocarbon growth is created as:
−[[[Fe2+]((CO2)2)2−]]− + H2 + e = H(CO2) + [[Fe2+][[CO]2−]] + H2O
−[[[Fe2+]((CO2)2)2−]]− + 1.5H2 + FeH+ + e = 2[[Fe2+][[CO]2−]] + 2H2O
Hydrocarbon generation (chain growth) at the surface sites takes the form:
1.5H2 + [[Fe2+][[CO]2−]] + e = [[Fe2+][[CH]3−]] + H2O
2[[Fe2+][[CH]3−]] + 0.5H2 = [FeH]+ + [[Fe2+][[CH]3−][[CH2]2+]]+ + 2e
[[Fe2+][[CH]3−][[CH2]2+]]+ + [[Fe2+][[CH]3−]] + 0.5H2 = [FeH]+ + [[Fe2+][[CH]3−][[CH2]2+][[CH2]2−]]
[[Fe2+][[CH]3−][[CH2]2+][[CH2]2−]] + [[Fe2+][[CH]3−]] + 0.5H2 = [FeH]+ + [[Fe2+][[CH]3−][[CH2]2+][[CH2]2−][[CH2]2+]]+
Hydrocarbon desorption takes the form:
[[Fe2+][[CH]3−][[CH2]2+][[CH2]2−]] = [[Fe2+][[CH]3−]] + CH2CH2
[[Fe2+][[CH]3−][[CH2]2+][[CH2]2−]] + H2 = [[Fe2+][[CH]3−]] + CH3CH3
Utilizing water, the desorption takes the form:
[[Fe2+][[CH]3−][[CH2]2+][[CH2]2−]] + 2H2O + 2e = [[Fe2+][[CH]3−]] + CH3CH3 + 2OH
In a gaseous FT reaction, the catalytic site is Fe0. In an aqueous Fe reaction, the catalytic site is one or more of Fe2+ or Fe(OH)2+. Both carboxylate and hydrocarbon formation, within an aqueous environment, utilize the same sites [74].
FT activation energies (Ea) change with temperature [75]. Below 170 °C, they are within the range 2 to 10 kJ mol. They have a Ln (Arrhenius factor (Ar)) of between 0 and 4 [76]. These values are determined [76] from a plot of Ln(CO) conversion (y-axis) versus 1/temperature T (K):
Ln(kobs) = Ln[Ar] ([−Ea]/R)(1/T),
where R = gas constant (8.31451 J K−1 mol−1); kobs = observed decomposition of reactants to products. It follows that
−(kobs)t = Ln(Ct=n/Ct=0),
where t = reaction time (t = n) in minutes; Ct=0 = the initial molar concentration of CO + CH4 in the feed gas; Ct=n = the molar concentration of CO + CH4 in the product gas; (1 − (Ct=n/Ct=0)) = the proportion of feedstock converted to hydrocarbon.
The observed activation energy Ea for the production of Route 1 desalination pellets can be reverse-engineered if Ln(kobs), T, and Ln[Ar], are known [76], i.e.,
[−Ea] = (Ln(kobs) − Ln[Ar])(RT),
where for Ln(Arrhenius Factor (Ar)) = 3, the calculated average Ea = 7.01 kJ M−1; for Ln(Arrhenius Factor (Ar)) = 4, the calculated average Ea = 9.41 kJ M−1. These values are consistent with the hydrocarbon production process, as they are part of the FT family of processes. The relationship between Ea and Ln(Ar) for both gaseous FT reactions and the formation of desalination pellets is provided in Figure 2 as a function of temperature. The resultant product, which is contained in the desalination pellets, is a [Fe0:Fe(a,b,c)@C0]n polymer.

1.6. Study Objectives

The Route 1 desalination pellet manufacturing process uses two reactors arranged in series. The first reactor (FBR) contains NaCl + silica gel. The second reactor (BCDR) contains water, NaCl, and Fe0.
This study sought to:
(i)
increase the amount of entrained n-C0 produced in the FBR and transferred in the product gas to the BCDR, and
(ii)
examine whether transferring the main point of n-C0 production to the FBR will result in the formation of a desalination catalyst and whether it will convert the BCDR from a net remover of CO + CH4 to a net producer of CO, CO2, and CH4. Both observations should occur if the aqueous FT model of CxHy and CxHyOz production is a viable hypothesis.
If both observations can be shown to be true, then three potentially commercial avenues of investigation will open up:
First, an alternative reaction route for the formation of the desalination pellets within the BCDR will have been identified.
Second, the desalination pellet composition could potentially be changed from Fe0:Fe(a,b,c)@n-C0 to C0@n-Fe0:Fe(a,b,c). In this instance, the dead-end porosity used to sequester the removed NaCl is switched from the dead-end pores within the Fe(a,b,c) polymer to dead-end pores within the C0. This approach would allow the active carbon produced from the processing of municipal waste or another carbon source to be utilized. This may provide a substantially cheaper and easier to manufacture pelleted desalination catalyst. A single experiment is provided to indicate whether this route may have merit for further investigation.
Third, hydrocarbon formation in the gaseous environment would be linked to tethered carbon (Fe:C). The production of CH4 and CO, would confirm that in an aqueous, redox, and diffuse environment, the carbon (for aqueous FT processes) need not be tethered. It can be physically adsorbed, i.e., Fe@C. This may allow, following further investigation, active nano-carbon produced from the processing of municipal waste or another carbon source to be utilized to provide a substantially cheaper, aqueous, and FT-like process that can operate at ambient temperatures.

2. Materials and Methods

The polymer terminology and the definition of Fe polymers are provided in references [77,78,79,80]. A Fe:Fe(a,b,c)@C0 desalination catalyst has a layered structure in which the innermost layer is Fe0. It has a chemically bonded corrosion surface of Fe(a,b,c) polymer (iron oxyhydroxides). The outer surface contains physically adsorbed n-C0.

2.1. Control Studies Undertaken Prior to the Commencement of This Study

The placement of Fe0 into saline water results in the iron corroding [1,81,82,83]. The Fe corrodes to form both ions and FexOyHz polymer products [1,82,83]. The corrosion reaction is exothermic [84,85,86]. The oxyhydroxide polymers reduce the salinity of the water. The Cl ions are either incorporated into the oxyhydroxide structure (e.g., chloride green rust [87,88,89,90]) or occupy structural molecular pores within the oxyhydroxide structure (e.g., akageneite, FeOOH [91,92,93,94]). In each of these two examples, the maximum molar removal of Cl ions is around 0.15 M Cl: 1 M Fe. Ion removal with both green rust and akageneite can be evaluated using standard adsorption analysis techniques [95,96,97,98].
The maximum molar removal of Na+ ions + Cl ions using the desalination pellets can exceed 4.7 M NaCl: 1 M Fe. The removed NaCl is sequestered as NaCl within dead-end pores contained within the pellets. The pellets operate by adsorbing ions from the water and sequestering them into the dead-end porosity.
Prior to the commencement of this study, a number of unpublished control trials were undertaken. These control trials used the Route 1 reactors and operating conditions. They were designed to determine if the composition of the pressurizing gas was an essential requirement to produce the desalination pellets.
  • Control Experiment 1. Pressurising gas: air (and not WSG). The product oxyhydroxide was pelleted, and 300 g of pellets was placed in 10 L saline (10 g NaCl L−1) water at NTP. The water was left for 300 days before being reanalysed. No reduction in water salinity was recorded.
  • Control Experiment 2. Pressurising gas: nitrogen (and not WSG). The product oxyhydroxide was pelleted, and 300 g of pellets was placed in 10 L saline (10 g NaCl L−1) water at NTP. The water was left for 300 days before being reanalysed. No reduction in water salinity was recorded.
  • Control Experiment 3. Pressurising gas: a mixture of 80% N2 and 20% CO2 (and not WSG). The product oxyhydroxide was pelleted, and 300 g of pellets was placed in 10 L saline water at NTP. The water was left for 300 days before being reanalysed. No reduction in water salinity was recorded.
These observations indicate that the presence of one or more of H2, CO, and CH4 (WSG) in the pressurizing gas was an essential feedstock component.

2.2. Iron Powder Compositions

In this study, the same m-Fe0 source that was used to construct the original Route 1 desalination pellets was used. The supplier indicated that >70% of the particles were <40 microns (Fe total = >93%; Fe0 = >87%).
The powders used in this study were Q235C/U12358 grade (Chinese Standard GB/T 700-2006). When fresh (i.e., when manufactured), they contain <0.17 wt % C; <0.35 wt % Si; <1.4 wt % Mn; <0.04 wt % P; <0.04 wt % S; <0.3 wt % Cr; <0.3 wt % Ni; <0.3 wt % Mo; <0.3 wt % Cu. The balance is Fe0, FexO2, and FexOyHz.
No analyses of BET surface area (expected to be <1 m2 g−1) or chemistry (XRD, XRF, etc.) were undertaken for the catalyst ingredients or the products.

2.3. Hydrogen

All of the reactors and the conduits used in the reactors were constructed from copper with brass fittings. At operating pressures above 0.17 MPa, some of the hydrogen contained within these pipes will leak through the external pipe walls. An example of prolonged hydrogen leakage through a reactor conduit wall (15 mm O.D.) is provided in Figure 3. In this study, H2 was used to maintain reducing conditions within the reaction environment. It was not assumed to be a primary reactant. Consequently, a high level of hydrogen conduit leakage (up to 95%) was tolerated.
The permeability of copper to hydrogen is addressed elsewhere [99,100]. The presence of NaCl enhances this permeability by 1 to 2 orders of magnitude [101].

2.4. Reactor Shell Structure

The desalination pellet manufacturing process creates two primary products: (i) a solid desalination metal oxyhydroxide polymer; (ii) hydrocarbons. CO2 is an unwanted waste product.
Copper tubing acts as a hydrogen-selective membrane (Figure 4) under the reaction conditions. Therefore, by constructing the reactor with a dual annulus in accordance with patent GB2475479B, it is possible to:
  • Maintain a reducing environment within the inner annulus (Figure 4)
  • Remove excess hydrogen into the outer shell (and outer annulus) to create a high-purity hydrogen gas stream (Figure 4)
This conceptual reactor design allows it to be placed in a borehole, a trench, or a waterbody, or on the ground. In order to meet regulatory constraints, in most regions, the reactor will be placed within a bunding shell (Figure 4).
The conceptual commercial design model for a future (TRL7) commercial pilot plant that manufactures desalination pellets (at the onset of this study) is shown in Figure 5. The concept plant takes a WSG and passes it into a reactor group, termed R1. This reactor group manufactures the desalination pellets and extracts hydrogen. The residual gases are then passed into a second reactor (R2). This reactor uses Fe0 + CO2 + H2O to generate cyclic hydrocarbons. This study examined the operation of the inner shell (Figure 4) associated with the R1 reactor complex (Figure 5).
The composition of live WSG is highly variable and is a function of feedstock type, the amount of air used (in an internally heated gasifier), and the moisture content of the feedstock [56]. The H2:CO ratio and volume is optimised at a gasifier temperature of 800 to 950 °C [56].

2.5. Data

The quantitative data is provided in the Supplementary Materials File in Figures S1–S9. The measured data was collated and processed in accordance with the standard UK statistical methodology [102]. Regression trend lines and associated statistics were calculated in MS Excel 2019. The coefficient of determination, R2, is the square of the Pearson Correlation Coefficient (PCC). This coefficient was calculated automatically using Excel 2019, and it is displayed as R2 using its trendline function. It is used to give an indication of the strength of the statistical correlation between two variables associated with a specific regression trend line [103,104]. By definition, R2 falls between 1 and 0, and PCC falls between +1 and −1 [103,104]. A detailed breakdown of the statistical interpretation used between R2 and the statistical correlation strength is provided in references [103,104].

2.6. Patents

The now-lapsed UK patents which apply to the process trains, catalysts, and reactors used in this study are:
(i)
Maclaurin Retort used to manufacture the WSG from municipal waste: US1130001A; GB191501380A; US1158066A; GB108339A;
(ii)
Reactor shell structure used to construct the process elements (USA, EPB, and DSA) of the process train: GB2475479B;
(iii)
Rapid pressure swing adsorption desorption process used: GB2470764B;
(iv)
Use of halite in the FBR: GB2463878B (Supplementary Materials, Section S3);
(v)
Construction of the BCDR and the manufacture of desalination pellets and associated catalytic material: GB2520775A.
The reactor train was constructed from three modular units arranged in series. They are a fixed-bed reactor (FBR), a bubble column diffusion reactor (BCDR), and a downstream gas storage volume (DGSV).
In a conventional reactor process, the feed gas pressure and the pressure applied to each part of the FBR and BCDR remains constant at all times. In a RPSAD (rapid pressure swing adsorption desorption) environment, a continual oscillation in pressures is required. This can be achieved by altering the flow pressures entering the reactor complex or by choking the gas flow exiting the process. This applies a simultaneous and constant controlled change through the process.
This study uses a RPSAD process in which (i) increases in pressure (and gas volume) in the FBR are associated with decreases in pressure (and gas volume) in the DGSV, and (ii) decreases in pressure (and gas volume) in the FBR are associated with increases in pressure (and gas volume) in the DGSV.
Linking the three units together creates a single process. Feed gas is supplied at a constant pressure y and flow rate. It creates a continually oscillating pressure within the FBR. The pressure p continually varies within the range of 0.1 MPa and y MPa. The gas volume within the porosity h m3 of the particle bed of the FBR continually varies within the range of h to ((y/0.1)(h)). This part of the reactor process (including associated conduits) is termed an upstream storage area (USA) in GB2475479B.
The BCDR operates as a pressure bridge between the FBR and DGSV. Gas can only flow from the FBR to the DGSV via the BCDR when the gas pressure within the FBR exceeds the restraining pressure. This restraining pressure is exerted by the water column in the BCDR combined with the pressure within the DGSV. GB2475479B terms the DGSV a downstream (gas) storage area (DSA). The BCDR operates within this environment as a poroelastic unit. Its permeability to gas continually varies. This variation is a function of the pressure differential between the pressure in the USA and the pressure in the DSA. GB2475479B terms this unit an elastic permeable barrier (EPB).
The process terminology (USA, EPB, and DSA) is used in the text. The equivalent construction terminology used in the text is FBR, BCDR, and DGSV, respectively. The USA encompasses all of the pipework to the BCDR. The EPB and BCDR occupy the same volume of the reactor. The remaining conduits and volume to the discharge choke point are incorporated in the DSA.

2.7. Reactor Train

The reactor train (Figure 6) contains two reactors, a fixed bed reactor (containing halite + m-Fe0, USA), and a bubble column diffusion reactor containing water, NaCl, and m-Fe0 (EPB). The USA receives a gas feed. The product gas from the USA is passed to the downstream EPB. The reactor train is operated as a rapid catalytic pressure swing adsorption/desorption reactor (RPSAD). This requires part of the reactor train to operate as an elastic permeable barrier (EPB). It also requires the reactor to contain an upstream gas storage area (USA) and a downstream gas storage area (DSA). The USA, EPB, and DSA terminology, technical requirements, and characteristics are further defined in UK Patent GB2470764B.
RPSAD reactor trains are used to enhance the rate constant for selected reactions by several orders of magnitude. They have previously been used to
  • enhance the utilisation of COx species contained in a SG: (a) FT reaction (UK Patent GB2470764B); (b) methanol formation [105]; (c) Fe:Fe(b)@C0 desalination catalyst (Route 1), and to
  • enhance the rate of desalination in pilot (TRL7) desalination reactors containing supported Fe0:Fe(b)@urea and SiO2@Fe(b)@urea desalination catalysts.
A simple mathematical explanation of the assumptions underlying the rate constant increase in a RPSAD reactor train was established [106]. The RPSAD process enhances adsorption rates during periods of rising pressure and enhances desorption rates during periods of dropping pressure [106].

2.7.1. SWSG Composition

A dry SWSG was constructed by BOC/Linde, Glasgow, UK (46.03% N2, 16.88% H2, 8.33% CO2, 11.97% CO, and 16.79% CH4). The gas composition used was based on the gas composition from a Maclaurin internally heated carbonization retort operating at 1200–1500 K (Retort number 4, Grangemouth, UK) [107].
The gas supply pressure was controlled using a pressure regulator supplied (and branded) by BOC/Linde. A second (backup) pressure regulator was placed between the gas supply and the USA. The gas pressure was then checked before entry to the USA using a separate flow line with a heavy-duty gas pressure gauge. This was purchased from Cole Parmer. Separate gas flow lines filled with (liquid) glycerine and equipped with pressure gauges were placed between the USA and EPB and after the EPB. The gas flow rate entering the USA was controlled using an inline, precision-machined, acrylic flow meter. This was configured with a control valve on its inlet, which was purchased from Cole Parmer (Figure 7a).

2.7.2. Reactor Train Structure

The reactor train was operated continuously at ambient temperatures (283 K to 293 K) for 46.6 days. The feed gas was delivered to the reactor train at a flow rate of 30 mL m−1 and pressure of 0.3 MPa. The trial was terminated when the printed circuit board (PCB) of the gas chromatograph (GC) ceased to operate. The flow rate of 30 mL m−1 was selected to allow direct comparison with the published Route 1 trial.
Gas composition sampling points (such as that shown in Figure 7b) were placed at three locations (Figure 8). Their positioning was designed to: (i) monitor the feed gas composition; (ii) monitor the product gas within the USA after it had exited the FBR; (iii) monitor the product gas composition contained within the DSA.
The USA and FBR (Figure 8) were constructed from 15 mm O.D. Cu0 conduits. Prior to the commencement of this trial, a number of different FBR lengths and orientations, were trialled. These trials used both 15 mm O.D. and 22 mm O.D. Cu0 pipework. Orientation of the FBR reactor was found to be unimportant. Inclined or vertical pipework was found to aid the loading and discharge of particulate material into and from the FBR.
The Cu0 pipes and associate compression fittings were purchased from Screwfix Ltd., Perth, UK. Figure 9a shows an example reactor containing 12 m of FBR, which was constructed from four inclined, 3 m-long pipe segments. The left-hand pipe segment (Figure 9a) receives (at its top) the feed gas conduit. The product gas exits the FBR at the top of the right-hand pipe segment. The annuli of the three link segments of pipe connecting the 3 m pipes (Figure 9a) contain no particulate matter. The FBR section of the USA was constructed (Figure 9b) from two 3 m-long, 15 mm O.D. (13 mm I.D.) Cu0 conduits filled with halite + Fe0 + Cu0 (Table 1). The FBR loading was limited by the particle weight, which could be filled into two 3 m-long sections of pipe.
The USA volume incorporates both the porosity within the FBR (Figure 9) and the annular volume of the link conduits (Figure 9).
The EPB’s BCDR (Figure 8 and Figure 9b) was constructed from 22 mm O.D. Cu0 conduits arranged to comply with patent GB2520775A. The BCDR had a core rectangular structure. The rising, bubbling gas continually circulates the water within the BCDR in a circular motion around the rectangle. The product gas exits the EPB and enters the DSA. Some of this exiting gas is wet. The DSA structure incorporated a condensation (dew point) mechanism with an associated reflux to recover this water. None of the water was circulated through the ZVI. The water column above the ZVI–water contact contained 2.35 L of water. Gas was discharged from the USA to the EPB, through a 6 mm Cu0 conduit containing a gas sampling point (Figure 8). The gas entered the EPB (as 3 mm diameter bubbles through a 3 mm I.D. distributer) at an elevation 10 cm above the ZVI–water contact.
The DSA (Figure 7c and Figure 9b) was constructed from 22 mm O.D Cu0 tubing. The gas conduits were constructed from 4, 6, 10, and 15 mm O.D. Cu0 conduits. The ZVI (Table 1) was held in a horizontal cartridge attached to the base of the EPB (Figure 9b).
The reactor train was constructed using 4 mm, 6 mm, 8 mm, 10 mm, 15 mm, and 22 mm O.D. Cu0 copper tubing and associated brass fittings and valves. These were purchased from Wickes Ltd. Perth, UK; Screwfix Ltd. Perth, UK; Cole Parmer, Saint Neots, UK. Pressure gauges, regulators, flow meters, flow controllers, and valves were purchased from Cole Parmer and BOC/Linde. The copper tubing used was the standard grade used in the UK for household and business gas appliances to convey gas from the gas meter to the gas appliance.

2.8. Gas Measurement and Measurement Equipment

A high-temperature thermal conductivity detector (TCD) and gas chromatograph (GC), both manufactured by SRI Instruments Inc. (Torrance, CA, USA), were used to analyse the gases. The GC was calibrated using standards purchased from BOC/Linde. The calibration levels used were as follows: N2: 0%, 20%, 46%, 80%; 100%; H2: 0%, 5%; 16%; 50%; CO: 0%, 1%, 12%; CO2, 0.1%; 8%, 20%; CH4: 0%, 10%, 17% 20%; CxHy: <10%. A GC area vs. mole % regression curve was used to define the product gas’s concentrations. Samples for GC gas analysis were extracted (from the flow line annulus) using a syringe via a Shimadzu BTO septum (Figure 7b). The syringe gas sample size was 0.7 cm3. GC response sensitivity increased with increasing syringe size. A syringe size of 0.5 cm3 gives an accurate sensitivity to 100 ppm (0.1 mole %). In this study, gas compositional accuracy was assumed to be high for concentrations above 0.1 mole %. At lower concentrations, the results should be interpreted as indicative (indicating presence and relative abundance) with decreasing accuracy as the mole concentration reduces below 0.1 mole %.
The carrier gas was He. The operating conditions were as follows: start temperature: 283 K; ramp temperature: 20 K/min; stable temperature: 523 K; run time: 40 min to obtain molar concentrations of the following: H2, N2, CO, CO2, CH4, C2Hx, C3Hx, C4Hx, C5Hx, and C6Hx. The software used was SRI Peak Simple version 4.88. The use of He as the carrier gas was recommended by SRI. At low concentrations while using an He carrier gas, H2 gives a positive TCD peak response [108]. At high concentrations, H2 gives a negative TCD peak response [108]. All other gas components give a positive TCD peak response for concentrations between 0% and 100%. To account for these changes, the hydrogen concentration was determined [2] as:
Hydrogen, % = 100 − N2 − CO − CO2 − CH4 − CxHy
WSG produced by an internally heated retort contains N2 [107]. The N2 in the feed gas acts as an inert gas [2.3]. A flow meter (Figure 7a) was used to measure the gas flow rate entering the reactor complex. It automatically follows that the product gas flow rate will be directly proportional to the concentration of nitrogen contained in the product gas. Most flow meters have rate gauges, which are a function of the gas composition being processed. Therefore, the only accurate values for the product gas flow rates are obtained by normalising the gas composition in the product gas. Normalisation is relative to the gas composition in the feed gas. This approach has been an accepted practice in FT studies since the 1930s [109].
The number of moles of N2 entering the reaction environment equals the number of moles of N2 leaving the reaction environment [2,3]. This allows the normalised gas species Gs’s concentration in the product gas (Supplementary Materials Figures S1–S6) relative to the feed gas CN to be determined [2,3] as:
CN, moles = CA(Nf/Np),
where CA = observed molar concentration of Gs in the product gas, Nf = molar concentration of N2 in the feed gas, and Np = molar concentration of N2 in the product gas.

2.9. Chemicals

The halite granules (0.5–5 mm) were purchased from Wickes Ltd., Perth, UK. The zero-valent metals (m-Fe0, m-Al0, m-Cu0), were purchased from MB Fiberglass, Newtownabbey, UK. The powders had a particle size within the range of 0.002 to 0.08 mm.
The exact particle size, composition, and concentrations of the feed’s Fe0, Cu0, and Al0 were not considered to be critical. The Fe0 powder’s characteristics are as follows. Particle Data: <45 Microns = 70%; Apparent Density: Approx 2.8 g/cm³; Chemical Analysis: Fe—Total: 93%; Fe—Metallic: 87%. Cu0 powder passes through a 240 mesh; 95% of Al0 particles are <350 microns.
The fresh water used in the experiments was natural spring water (pH 6.5) emanating from fractured andesites belonging to the Devonian Old Red Sandstone Volcanic Series (Source National Grid Reference: NO 02,817 14399; 56°18′43″ N, 003°34′21″ W).

2.10. Water Analysis Measurement Equipment

The instruments used were:
  • ORP (oxidation reduction potential) meter (HM Digital) calibrated at ORP = 200 mV; measured ORP (oxidation reduction potential) values were converted to Eh, mV as Eh, mV = −65.667pH + 744.67 + ORP (mV) using a quinhydrone calibration at pH = 4 and pH = 7.
  • pH meter (HM Digital) calibrated to pH = 4.01; 7.0; 10.0.
  • EC (electrical conductivity) meter (HM Digital meter calibrated at EC = 1.431 mScm−1).
  • Cl ISE (Ion Selective Electrode); Bante Cl ISE, EDT Flow Plus Combination Cl ISE; Cole Parmer Cl ISE attached to a Bante 931 Ion meter. Calibration was undertaken using 0.001, 0.01, 0.1, and 1.0 M NaCl calibration solutions.
  • Na+ ISE (Ion Selective Electrode); Bante Na ISE, Sciquip Na ISE; Cole Parmer Na ISE attached to a Bante 931 Ion Meter. Calibration was undertaken using 0.001, 0.01, 0.1, and 1.0 M NaCl calibration solutions.
  • Temperature measurements were made using a temperature probe attached to a Bante 931 Ion Meter.

2.11. Pellet Formation

At the conclusion of the trial, the ZVI cartridge was removed from the reactor. A Rothenberger pipe slicer was then used to cut the 15 mm O.D. pipe. This was achieved without the cutting wheel penetrating the Fe0:Fe(a,b,c)@C0 polymer. At this point, the polymer was brittle, and a twist of the pipe resulted in a clean flat break (Figure 10). The pipe was cut into 15 mm- to 25 mm-long segments. Each segment was measured and weighed. This allowed the weight of polymer and the weight of the Cu0 associated with each pellet to be determined.
There is no specific significance to the pellet length selected. Prior unpublished work indicated that 10 mm- to 30 mm-long pellets had a higher desalination rate constant than 10 cm- to 30 cm-long pellets. The Rothenberger pipe slicer allows pellets to be cut such that a 20 mm target pellet has a length of between 18 and 22 mm.

2.12. Hydrogen Losses

The GC results indicate a significant loss of hydrogen. The simplest explanation is that this hydrogen was adsorbed by the material contained within the EPB and USA. Alternatively, it was lost via discharge through the copper conduits, or it was removed by the CxHyOz species contained in the water.
A sample of the product water from the EPB was sent to Hall Analytical Laboratories Ltd. (part of the Agilant group), Manchester, UK for GCMS analysis. GC-MS analyses were performed using an Agilent 5973 mass spectrometer linked to an Agilent 6890 gas chromatography system. The organic components in the water were extracted, using dichloromethane (DCM). The analysis indicated traces of cyclohexane–isocyanatno; cyclohexane–isothiocyanatno; Phenol,2,5-bis(1,1-dimethylethyl); two unidentified species.
This analysis does not indicate that any significant CxHyOz species formation occurred in the BCDR during the reaction period. This observation is consistent with aqueous FT observations when a carbon source is supplied in the water [90,91]. It is not consistent with aqueous FT when the sole carbon source is iron carbides contained within the Fe0 particles [92,93,94].
The disappearance of the hydrogen is unresolved. The extensive presence of Cu(OH) and Cu(OH)2 on conduits associated with the disappearance of H2 (Figure 11) is enigmatic. These precipitates are interpreted here as probably indicative of hydrogen leakage through the Cu0 pipes.

2.13. Carbon Switching Trial

The bulk of the pellet formation cost is associated with cost of Fe0, the cost of Cu0, and the long time frame taken to produce a product. The evaluation of the results indicated that the presence of Cu0 may not be essential. Similarly, a major function of the Fe0:Fe(a,b,c) polymer appears to be to produce dead-end porosity to hold the removed NaCl. Therefore, it may be possible to remove the requirement for Cu0 and the bulk of the Fe0:Fe(a,b,c) polymer by switching to a porous active carbon source as the primary support to create porous C0:Fe(a,b,c) pellets.
No specific n-Fe0 precipitation method is preferred in making the C0@Fe0 desalination catalyst. The normal precipitation approach is to use a sol-gel approach, whereby an Fe salt is dissolved in water (the exact molar concentration is not critical). In this study, the concentration used was 100 g FeSO4 L−1. An appropriate amount of activated carbon (preformed moulded porous pellets (5 mm × 10 mm cylindrical pellets)) was added to the water containing the FeSO4. The mixture was allowed to soak for 24 h at NTP. The weight ratio of carbon to Fe used was 99.6%C0 + 0.4%n-Fe0. A reductant was then added to precipitate the n-Fe0 onto the C0 support.
The Fe0 precipitation agents which can be used include: NaBH4 (KR100975822B1; US20070022839A1), KBH4 (US20070022839A1), LiBH4 (US20070022839A1), Na2S2O4 (US8283034B2), Li2S2O4 (US8283034B2), K2S2O4 (US8283034B2), MgS2O4 (US8283034B2), CaS2O4 (US8283034B2), N2H4 [110], and polyphenols (US7963720B2; CN106077624B; CN112755963A; CN109967024B; CN113477214A). Polyphenols include, but are not limited to, tea extract, green tea extract, coffee extract, lemon balm extract, sorghum bran, sorghum bran extract, polyphenolic flavonoid, flavonoid, flavonol, flavone, flavanone, isoflavone, flavans, flavanol, anthocyanins, proanthocyanins, carotenoids, catechins, quercetin, and rutin (CA2728987C).
The choice of reductant is not critical. Likewise, the amount of reductant required is not critical, provided it is in excess of the minimum required to convert all the Fe2+ ions to Fe0. The C0@Fe0 desalination catalyst used in this study was created using a gallic acid polyphenol concentrate derived from black tea. The C0@Fe0 desalination catalyst was removed from the sol-gel solution after 4 h at NTP. The Fe0 produced using this process also incorporated some Fe-organic (Fe(b,c)) precipitates. The resultant pellet structure is illustrated in Figure 12.

2.14. Desalination Trials

The desalination trials were operated as follows:

2.14.1. Fe0:Fe(a,b,c)@C0 Trial

The 15 mm O.D Cu0 sheathed ZVI cartridge was removed from the reactor train after 46.6 days and drained. The cartridge was then cut into 15 to 25 mm segments, where each segment is defined here as a pellet (Figure 10). A typical cross-section through a pellet is shown in Figure 13a. Each pellet is highly porous and contains both interconnected and isolated pores and vugs. The total weight of pellet material recovered, excluding the weight of the Cu0 shell, was 240 g.
The pellets were intended for use as desalination pellets. An example of operation is provided in Figure 13b. In this example, 44.65 g of pellets were added to 1 L of static saline water (9.2 g NaCl L−1; Eh = 401.88 mV; pH = 6.21; EC = 15.2 dSm−1; temperature = 280 K). The pellets contained the following: 25.34 g Fe:Fe(b)@Cu@Al@Ca@C0 polymer + 19.31 g Cu0 pellet shell.
The sealed reactor had a head space (air) of 1.3 L. The reactor shell and top seal shielded the water from UV light. The reactor was placed in an unheated, partially open steading building. It was exposed to natural fluctuations in atmospheric temperature and pressure during the trial period.

2.14.2. C0@Fe0:Fe(a,b,c) Trial

The sealed reactor contained 1 L of static water and had a head space (air) of 1.3 L. The reactor shell and top seal shielded the water from UV light. The reactor was placed in an unheated, partially open steading building. It was exposed to natural fluctuations in atmospheric temperature and pressure during the trial period. n-Fe0 in the amount of 0.2 g L−1 precipitated onto and into the active carbon; the active carbon totalled 50 g L−1; the pellet size was 10 mm × 5 mm. The feed water salinity was 30.74 g L−1.

2.15. USA:FBR Control Experiment

Hydrocarbon formation was recorded when the FBR only contained NaCl + silica gel (Route 1) and when the FBR contained NaCl + Fe0 + silica gel (Route 2). A control FBR (constructed from 15 mm O.D Cu0 tubing) was filled with 130 g m-Fe0 + 130 g silica gel particles (to provide permeability). The synthetic WSG passed through the FBR at a rate of 30 mL m−1 for a period of 8 h. The gas delivery pressure was 0.3 MPa. The reactor was operated at ambient temperature (278 K to 285 K). The product gas was analysed for CxHy where x = >1. No hydrocarbon formation was observed. The results of this control test imply that NaCl can facilitate the production of hydrocarbons from WSG at ambient temperatures. A possible reaction sequence for the production of hydrocarbons in the presence of NaCl is documented in Table 2.

3. Gas Flow Results

The total volume of feed gas processed was 2.031 m3. Of this volume, 0.96264 m3 was N2; 1.086 m3 was potentially removable. Approximately 240 g of desalination catalyst was manufactured in the process. The average product gas flow rate leaving the FBR was 19.935 mL m−1, indicating an average volume contraction of 34%. The average product gas composition was 69.41% N2 + 1.21% H2 + 9.09% CO2 + 9.2% CO + 11.1% CH4 + 0.2% CxHy.
The average product gas composition, normalised to the feed gas, was: 46.03% N2, 0.80% H2, 6.03% CO2, 6.10% CO, 7.36% CH4, and 0.13% C2+. Total product gas volume was 1.337 m3; the variation in the product gas’s composition is summarised in Table 2.
A characteristic of all RPSAD process operations is high variability in product gas composition. This is demonstrated in Table 3, and it reflects the impact of oscillating pressure on adsorption and desorption rates. In an RPSAD process, the most accurate impression of the process is given by the average product composition.
The trial established statistical positive correlations between CH4:CO, CO:CO2, CO2:CH4, CO2:H2, and CH4:H2 (Supplementary Materials, Figures S1–S3). CH4 and H2 concentrations were always less than in the feed gas composition. Both CO and CO2 compositions’ concentrations can be above their levels in the feed gas. This is interpreted as an indication that (i) CH4, CO, and CO2 are adsorbed to form C0 + H2O; (ii) the pulsed desorption of CO, CO2, or localised reversal of the COx removal reaction can occur.
The net adsorption reaction was:
nFe0 + 16.08H2 + 9.43 CH4 + 5.87CO + 2.3CO2 = [nFe0@17.6C0] + 10.47H2O + 24.41 H2(ads),
Of the feed carbon volume, 47.4% was converted to C0 or CxHy; x = >1. The observed selectivity for the removed carbon atom destination was 96% C0 + 4% CxHy.
The average product gas composition, normalised to the feed gas entering the FBR, was 46.03% N2, 1.50% H2, 9.29% CO2, 9.92% CO, 11.59% CH4, and 0.16% C2+. The variability associated with the RPSAD process is demonstrated by the highly variable outcome ranges in Table 4. The total product gas volume was 1.581 m3. The increase in product gas volume relative to gas feed from the FBR was 0.2438 m3. Positive correlations were present between CH4:CO, CO:CO2, CO2:CH4, CO2:H2, and CH4:H2 (Supplementary Materials, Figures S4–S6). The observed C2+ compositional statistics are provided in Table 5.
The following average stoichiometric changes to the gas received from the FBR occurred:
11.37 C0 + 10.34H2O = 0.03C2H2 + 4.23 CH4 + 3.26CO2 + 3.82CO + 0.7H2 + 2.14H+ + 2.14e
The observed generated gas composition was 0.2%C2H2 + 35.1% CH4 + 27.1% CO2 + 31.7% CO + 5.8%H2. This analysis indicates that the bulk (64.6%) of the 17.6 moles of C0 removed in the FBR was entrained in the gas entering the BCDR. A maximum of 0.674 moles (8 g) of n-C0 (over the 46.6-day reaction period) was retained in the FBR, removed in the BCDR (to form the Fe0:Fe(b)@C0 desalination catalyst), or was contained in the product gas leaving the BCDR.

4. Desalination Pellet Results

The results of a single typical example trial test are reported here to illustrate the principal features associated with desalination. The pellets (Figure 13a) were placed in a static water body and monitored for 2152 h (89.6 days). The temperature was allowed to vary with changes in ambient temperature within the range of 273 to 283 K. The results indicated:
  • Salinity declined with time (Figure 13b). The salinity decline could be described by a linear equation, indicating that the NaCl removal involves a pseudo-zero order reaction.
  • The pH increased by 1.5 to 4 units (Figure 13c).
  • The Eh initially declined by up to 300 mV before increasing (Figure 13d).
  • The pellets contained an estimated 9 g Fe and removed 4.6 g NaCl over a period of 2152 h.
There is a weak negative polynomial regression relationship between Eh and pH (Figure 13e). This experiment confirms that the Route 2 process can be used to manufacture desalination pellets. These pellets have similar operating characteristics to those manufactured in Route 1.
The placement of Fe0 or Fe0:Fe(a,b,c) into a static body of water always rapidly increases the pH of the water. This change results from a primary reaction, which is catalysed by Fe0. This reaction is 2H2O = 2OH + 2H+. This reaction initially rapidly increases pH to a new stable level (Figure 13c). The pH then stabilizes, or drifts downwards, as additional OH- ions are removed by the Fe via the reaction Fe0 + 3OH = Fe(OH)3 + 3e (Figure 13c).
The increase in H+ ion availability coupled with the increased availability of e and the stable Eh at the water-Fe boundary results in the reactions H+ + e = H (physically adsorbed) and 2H+ + 2e = H2. Both of these reactions are associated with the initial decrease in Eh (Figure 13d). The substantial rise in Eh after 1500 h (Figure 13d) is associated with the change in Fe composition from Fe(OH)x to FeOOH; i.e., Fe(OH)3 = FeOOH + H2O; Fe(OH)2 = FeOOH + H+ + e. This reaction suite occurs at a higher Eh than the initial reaction set [1].
There is always a negative relationship between Eh and pH in a redox environment (Figure 13e) [1] due to the pH reaction H2 = 2H+ + 2e, where Eh = −0.0591 pH. Superimposed on this trend are the Eh:pH mineralogical (ion) reactions in water at the appropriate Eh and pH. In a redox environment, the equilibrium constant for each of these reactions is pH-dependent. The Eh changes (and variation) at a specific pH, result from the reaction quotients of the simultaneous reactions striving to reach equilibrium. The relationship between Eh and pH is defined by the Nernst Equation [1].
A statistical analysis of the performance of Route 2 desalination pellets is provided in Table 6. For comparison, a similar table is provided for Route 1 desalination pellets (Table 7). Both routes provide similar levels of desalination.

5. C0@Fe0 Desalination Pellet Results

The C@Fe0 pellets were placed in seawater and monitored. They demonstrated (Figure 14a) a decline in salinity to a base level. The removed NaCl was concentrated in the nano- and microporosity within the pellets (Figure 14b).
The desalination reaction is second order (Figure 14). This compares with the pseudo-zero order reactions (Figure 13b) produced by the Route 2 catalysts, in which the removed NaCl is stored within dead-end pores. In Route 2, a relatively fast adsorption by n-C0 with initial storage in open pores within the pellet is followed by the subsequent transport of the Na+ and Cl ions through the Fe(b) polymers. Desorption is into dead-end porosity within the pellets. This slower route is via Schottky defects [111] and Frenkel defects [112] within the Fe(b) polymers.
Pseudo-zero order reaction patterns occur when a multi-stage adsorption reaction includes initial adsorption steps which are significantly faster than the subsequent desorption reaction [113,114]. The results in Figure 14a lend support to the model for the Route 2 pellets, where the initial desalination adsorption is via C0. This is followed by slower transport through the Fe(b) polymers with subsequent desorption.

6. Discussion

This study had two technoeconomic objectives. They were:
  • Objective 1: The initial Route 1 manufacturing study indicated that the desalination pellets were formed as a by-product of a FT process where, in the BCDR, aCH4 + bCO = cC + dCO2 + eCxHy (x = >1; C is either C0 or CxHyOz), and where the FBR was a net producer of CO2. This study examined whether including Fe0 in the FBR, would result in an initial reaction of the form aCO + bCO2 + cCH4 = dCxHy + eC and still result in the formation of a desalination catalyst in the BCDR.
  • Objective 2: If the first objective was successful, the study was scheduled to test whether it would be possible to reformulate the catalyst using a sol-gel approach to precipitate it onto a carbon support. This would potentially facilitate a simpler manufacturing process.

6.1. Significance of Hydrocarbons

The mass balance analysis of the change in gas composition through the BCDR, indicated that entrained n-C0 (when combined with Fe0) will react with water to form H2, CH4, CxHy, CO, and CO2. FT studies previously concluded that at elevated temperatures and pressures, surface carbon is a possible intermediate in the synthesis of hydrocarbons [115]. If, as inferred, the n-C0 is adsorbed to form Fe@C0 or Fe(a,b,c)@C0, then it is reasonable to expect the reactions summarized in Table 8 to occur [116].
CH4 disassociation sites are located on the particle’s surface [116], whereas sites associated with CO, CO2, and CxHy disassociation tend to be embedded within the particle [116]. These site locations are consistent with the pattern of gas discharge recorded in Supplementary Materials, Figures S1–S9. This information is interpreted as an indication that carbon is incorporated in the Fe:Fe(b)@C0 material in both surface sites and in sites incorporated within the Fe(b) structure.
Silica gel is a known adsorbent of H2 [117], and it has been used to concentrate hydrogen in some pressure swing adsorption (PSA) separators [118,119]. At 423 K, silica gel is known to catalyse hydrocarbon formation CxHy (where x < 5) from CO + H2 [120]. No control experiments have been undertaken to ascertain whether the silica gel used in this study is able to catalyse hydrocarbon formation.
The largest hydrocarbon peak (Figures S6 and S9) was associated with a normalized feed gas from the FBR that comprised the following: 46.03% N2; 0.69% H2; 9.11% CO; 4.46% CO2; 11.41%CH4; 0.4% C2H2. The normalized product gas from the BCDR comprised the following: 46.03% N2; 7.49% H2; 8.30% CO; 9.31% CO2; 11.11% CH4; 9.02% CxHy (0.12% C2H2; 1.40% C2H4; 4.01% C2H6; 3.32% C3H4; 0.17% C3H6). The molar mass balance is summarized as:
25.19 C0 + 8.89H2O + 0.3 CH4 + 0.81CO + 0.04C2H2 + 20.09H+ + 20.09 e =
0.12C2H2 + 1.40C2H4; + 4.01C2H6; + 3.32C3H4; + 0.17C3H6 + 4.85CO2 + 0.7H2 + 2.14H+ + 2.14e
The product selectivity for the used carbon was 81.6% hydrocarbons:18.4% CO2. The pulsed expulsion of both hydrogen and hydrocarbon gases is consistent with the formation of gas-filled vugs within the desalination catalyst (Figure 10 and Figure 13a). The production of significant hydrocarbon and hydrogen pulses from the desalination catalyst bed is consistent with the catalyst containing FexCy or Fe(a,b,c)@C0 [2,90,91,92,93,94]. Earlier studies suggest that the hydrocarbon production can be described using an Anderson–Schulz–Flory (ASF) approach [90,91,92,93,94]. The ASF model assumes that the hydrocarbon chain forms via the stepwise addition or insertion of C1 intermediates (CHx) with a constant chain growth probability (alpha (α)). Alpha is assumed to be independent of chain length. It is commonly calculated as (e.g., US Patent US 7282139B2)
α = Mn+1/Mn,
where Mn = number of moles of hydrocarbon with a carbon number n, and Mn+1 = number of moles of hydrocarbon with a carbon number n + 1.
While the current study’s focus is to produce a desalination catalyst, the observation that it is possible to create significant quantities (at potentially commercial rates (Equation (24))) of C2Hx + C3Hy hydrocarbons at NTP from entrained n-C0 is unexpected, and it is a deviation from earlier studies [90,91,92,93,94].
This observation is interpreted as follows:
  • In a conventional FT process, the carbon reaction sites are chemically bound to the Fe0 as Fe3C or Fe5C2. The reactor is operated under an isothermal, constant pressure and constant gas flow rate regime. CO is used as the primary source of carbon for chain growth. This creates a stable reaction environment, which allows an equilibrium reaction quotient (Q) to be established. Q is always < equilibrium constant K. The carbon chains grow as fronds emanating from the surface of the Fe particles. Chain cleavage occurs when the chains exceed a critical length. Although ideally, a specific number of carbon atoms is desired in the cleaved chain (e.g., octane), in practice, the product suite includes a portfolio of different chain lengths. These are commonly described using an Anderson–Schulz–Flory (ASF) relationship (Equation (25)).
  • In the BCDR used in this study, there were some Fe3C or Fe5C2 incorporated within the Fe. Within the BCDR, entrained carbon interacts with the Fe to form physically adsorbed sites (Fe@C). The chain growth takes the form Fe@-[CH]-[CH]-. The chains are easily dislodged by the rapid pressure fluctuations present in the BCDR. The principal hydrocarbon product produced was C2H2. These observations indicate that it may be possible, following additional experimentation (using Route 2), to use WSG to develop an ambient temperature route for the production of C2H2. A by-product of this FT process will be the formation of desalination pellets.

6.2. Desalination Pellets

The concept of being able to place a pellet in saline water to effect desalination without requiring an external energy source or producing waste brine has the potential to improve water quality.
The active pellet material is considered to form as a by-product of an aqueous FT process in which the FT catalyst is Fe0. The active material is considered to be a Fe(a,b,c)@C0 polymer. The Route 1 approach manufactures the active material as a by-product of CO + CH4 removal in a BCDR. The results of Route 2 demonstrate that the principal carbon conversion zone to n-C0 can be switched to an upstream FBR reactor. The passage of the entrained n-C0 to the BCDR forms a Fe(a,b,c)@C0 polymer, which is capable of being pelleted. This process is associated with the formation of H2, CH4, CO, and CO2.
These observations confirm that the manufacturing process is an aqueous variant of the gaseous Fischer–Tropsch process. They may indicate that spent Fe0 catalyst from a commercial FT reactor could have potential desalination applications.
A detailed discussion of the properties and operation of the desalination pellets is outside the scope of this study.

7. Conclusions

This study establishes the following: (i) a FBR containing a mixture of Fe0 and NaCl can be used to covert CO, CO2, and CH4 to n-C0; (ii) passage of the n-C0 into a BCDR containing Fe0 results in the formation of the desalination catalyst (Fe0:Fe(a,b,c)@C0) + CH4 + CO + CO2 + CxHy, where x > 1. This process is interpreted as belonging to the Fischer–Tropsch group of processes. Of the total volume of CH4 + CO + CO2 entering the FBR, 47.4% was converted to C0+ CxHy, where x >1. The selectivity was 96% n-C0 + 4% CxHy. The BCDR converted 64.6% of the n-C0 into CH4, CO, CO2, and CxHy. The selectivity was 37.2% CH4 + 28.7% CO2 + 33.6% CO + 0.5% CxHy. The residual n-C0 (35.4%) was retained in the n-Fe:Fe(a,b,c)@C0 polymer.
The desalination catalyst, when placed in water, reduced its salinity using a pseudo-zero order reaction. An analysis of pellet performance indicates that an average of >60% desalination is achievable. The removed NaCl was sequestered with the dead-end porosity of the catalyst. A single feasibility experiment tested the hypothesis that the critical location for the catalyst is on the surface of a pellet containing dead-end pores. This experiment (using C0@Fe0:Fe(a,b,c) using a seawater feedstock established a pseudo-second order desalination profile. It achieved >85% desalination.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/waste1020026/s1. Figure S1. USA. Carbon monoxide relationships. Figure S2. USA. Carbon dioxide relationships. Figure S3. USA. Methane and hydrogen relationships. Figure S4. EPB. Carbon monoxide relationships. Figure S5. EPB. Carbon dioxide relationships. Figure S6. EPB. Methane and hydrogen relationships. Figure S7. USA. Hydrocarbon compositions in the product gas. Figure S8. EPB. Hydrocarbon product compositions. Figure S9. EPB. Composition of the generated hydrocarbons in the product gas.

Funding

This research received no external funding.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

All of the data used in this study are contained in Table 1, Figure 13 and Figure 14, and Supplementary Materials Figures S1–S9.

Acknowledgments

The five reviewers are thanked for their thoughtful, detailed, constructive, and incise comments during the review process.

Conflicts of Interest

The author declares no conflict of interest.

References

  1. Pourbaix, M. Atlas of Electrochemical Equilibria in Aqueous Solutions; NACE International: Houston, TX, USA, 1974; p. 644. [Google Scholar]
  2. Antia, D.D.J. Remediation of Saline Wastewater Producing a Fuel Gas Containing Alkanes and Hydrogen Using Zero Valent Iron (Fe0). Water 2022, 14, 1926. [Google Scholar] [CrossRef]
  3. Antia, D.D.J. Purification of Saline Water Using Desalination Pellets. Water 2022, 14, 2639. [Google Scholar] [CrossRef]
  4. Brady, J.B.; Mogk, D.W.; Perkins, D. Making solid solutions with alkali halides (and breaking them). Teach. Mineral. Mineral. Soc. Am. Monogr. 1997, 3, 91–96. [Google Scholar]
  5. Vinograd, V.; Winkler, B. An efficient cluster expansion method for binary solid solutions: Application to the halite-silvite, NaCl-KCl, system. Rev. Mineral. Geochem. 2010, 71, 413–436. [Google Scholar] [CrossRef]
  6. Driesner, T.; Heinrich, C.A. The system H2O–NaCl. Part I: Correlation formulae for phase relations in temperature–pressure–composition space from 0 to 1000 C, 0 to 5000 bar, and 0 to 1 XNaCl. Geochim. Et Cosmochim. Acta 2007, 71, 4880–4901. [Google Scholar] [CrossRef]
  7. Makaryan, I.A.; Salgansky, E.A.; Arutyunov, V.S.; Sedov, I.V. Non-Catalytic Partial Oxidation of Hydrocarbon Gases to Syngas and Hydrogen: A Systematic Review. Energies 2023, 16, 2916. [Google Scholar] [CrossRef]
  8. Khademi, M.H.; Lotfi-Varnoosfaderani, M.; Palizvan, A. Partial oxidation process for syngas production. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 9; pp. 197–236. [Google Scholar] [CrossRef]
  9. Aboosadi, Z.A.; Yadecoury, M.F. Thermally intensification of steam reforming process by use of methane tri-reforming: A review. Int. J. Chem. React. Eng. 2019, 17, 20190108. [Google Scholar] [CrossRef]
  10. Fowles, M.; Carlsson, M. Steam reforming of hydrocarbons for synthesis gas production. Top. Catal. 2021, 64, 856–875. [Google Scholar] [CrossRef]
  11. Kiani, P.; Rahimpour, H.R.; Rahimpour, M.R. Steam reforming process for syngas production. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 4; pp. 81–96. [Google Scholar] [CrossRef]
  12. Salahi, F.; Zarei-Jelyani, F.; Rahimpour, H.R.; Rahimpour, M.R. Dry reforming for syngas production. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 5; pp. 97–118. [Google Scholar] [CrossRef]
  13. Jang, W.J.; Shim, J.O.; Kim, H.M.; Yoo, S.Y.; Roh, H.S. A review on dry reforming of methane in aspect of catalytic properties. Catal. Today 2019, 324, 15–26. [Google Scholar] [CrossRef]
  14. Sandoval-Diaz, L.E.; Schlögl, R.; Lunkenbein, T. Quo Vadis Dry Reforming of Methane?—A Review on Its Chemical, Environmental, and Industrial Prospects. Catalysts 2022, 12, 465. [Google Scholar] [CrossRef]
  15. Farsi, M. Reforming process design and modeling: Steam, dry, and autothermal reforming. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 4; pp. 123–140. [Google Scholar] [CrossRef]
  16. Rowshanzamir, S.; Eikani, M.H. Autothermal reforming of methane to synthesis gas: Modeling and simulation. Int. J. Hydrogen Energy 2009, 34, 1292–1300. [Google Scholar]
  17. Marzbali, M.H.; Kundu, S.; Halder, P.; Patel, S.; Hakeem, I.G.; Paz-Ferreiro, J.; Madapusi, S.; Surapaneni, A.; Shah, K. Wet organic waste treatment via hydrothermal processing: A critical review. Chemosphere 2021, 279, 130557. [Google Scholar] [CrossRef] [PubMed]
  18. Okolie, J.A.; Nanda, S.; Dalai, A.K.; Berruti, F.; Kozinski, J.A. A review on subcritical and supercritical water gasification of biogenic, polymeric and petroleum wastes to hydrogen-rich synthesis gas. Renew. Sustain. Energy Rev. 2020, 119, 109546. [Google Scholar] [CrossRef]
  19. Vallejo, F.; Diaz-Robles, L.; Cubillos, F.; Espinoza, A.P.; Espinoza, L.; Pinilla, F.; Pino-Cortes, E. Valorization of municipal solid waste using hydrothermal carbonization and gasification: A review. Chem. Eng. Trans. 2020, 81, 1045–1150. [Google Scholar]
  20. Altikat, A.; Alma, M.H. Prediction carbonization yields and the sensitivity analyses using deep learning neural networks and support vector machines. Int. J. Environ. Sci. Technol. 2022, 1–10. [Google Scholar] [CrossRef]
  21. Pérez, V.; Bailera, M.; Lisbona, P. Syngas production by gasification processes. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 2; pp. 17–46. [Google Scholar] [CrossRef]
  22. Miskolczi, N.; Gao, N.B.; Quan, C. Pyrolysis-gasification of biomass and Municipal Plastic Waste using transition metal modified catalyst to investigate the effect of contaminants. J. Energy Inst. 2023, 108, 101233. [Google Scholar] [CrossRef]
  23. Al-Fatesh, A.S.; AL-Garadi, N.Y.; Osman, A.I.; Al-Mubaddel, F.S.; Ibrahim, A.A.; Khan, W.U.; Alanazi, Y.M.; Alrashed, M.M.; Alothman, O.Y. From plastic waste pyrolysis to Fuel: Impact of process parameters and material selection on hydrogen production. Fuel 2023, 344, 128107. [Google Scholar] [CrossRef]
  24. Hu, G.; Zhao, Q.; Manning, M.; Chen, L.; Yu, L.; May, E.F.; Li, K.G. Pilot scale assessment of methane capture from low concentration sources to town gas specification by pressure vacuum swing adsorption (PVSA). Chem. Eng. J. 2022, 427, 130810. [Google Scholar] [CrossRef]
  25. Cheung, M.H.T. Green energy recovery by blending treated biogas into town gas pipeline networks. HKIE Trans. 2020, 27, 173–182. [Google Scholar] [CrossRef]
  26. Park, Y.M.; Kim, B.G.; Gao, X.; Zhang, X.; Roh, H.S.; Chung, C.H.; Bae, J.W. Ordered mesoporous Co3O4-Al2O3 bimetal oxides for CO2 hydrogenation to synthetic natural gas: Effects of surface Al2O3 distribution. Fuel 2023, 343, 127943. [Google Scholar] [CrossRef]
  27. Shi, Y.; Li, H.; Chen, H.; Zhao, Y.; Cao, Y.; Liu, X.; Duan, X.; Qian, G.; Zhou, X. Thermal management of natural gas production from coke oven gas by optimizing catalyst distribution and operation conditions. Chemosphere 2023, 327, 138536. [Google Scholar] [CrossRef] [PubMed]
  28. Lisbona, P.; Bailera, M.; Pérez, V. Methane production from syngas. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 3, Chapter 4; pp. 93–109. [Google Scholar] [CrossRef]
  29. Kim, T.Y.; Jo, S.B.; Woo, J.H.; Lee, J.H.; Dhanusuraman, R.; Lee, S.C.; Kim, J.C. Investigation of Co–Fe–Al Catalysts for High-Calorific Synthetic Natural Gas Production: Pilot-Scale Synthesis of Catalysts. Catalysts 2021, 11, 105. [Google Scholar] [CrossRef]
  30. Gupta, P.K.; Kumar, V.; Maity, S. Renewable fuels from different carbonaceous feedstocks: A sustainable route through Fischer–Tropsch synthesis. J. Chem. Technol. Biotechnol. 2021, 96, 853–868. [Google Scholar] [CrossRef]
  31. Herbers, A.; Kern, C.; Jess, A. Cobalt Catalyzed Fischer-Tropsch Synthesis with O2-Containing Syngas. Catalysts 2023, 13, 391. [Google Scholar] [CrossRef]
  32. Alsudani, F.T.; Saeed, A.N.; Ali, N.S.; Majdi, H.S.; Salih, H.G.; Albayati, T.M.; Saady, N.M.C.; Shakor, Z.M. Fisher–Tropsch Synthesis for Conversion of Methane into Liquid Hydrocarbons through Gas-to-Liquids (GTL) Process: A Review. Methane 2023, 2, 24–43. [Google Scholar] [CrossRef]
  33. Jones, M.P.; Krexner, T.; Bismarck, A. Repurposing Fischer-Tropsch and natural gas as bridging technologies for the energy revolution. Energy Convers. Manag. 2022, 267, 115882. [Google Scholar] [CrossRef]
  34. Neuner, P.; Graf, D.; Mild, H.; Rauch, R. Catalytic Hydroisomerisation of Fischer–Tropsch Waxes to Lubricating Oil and Investigation of the Correlation between Its Physical Properties and the Chemical Composition of the Corresponding Fuel Fractions. Energies 2021, 14, 4202. [Google Scholar] [CrossRef]
  35. Karaba, A.; Rozhon, J.; Patera, J.; Hájek, J.; Zámostný, P. Fischer-Tropsch Wax from Renewable Resources as an Excellent Feedstock for the Steam-Cracking Process. Chem. Eng. Technol. 2021, 44, 329–338. [Google Scholar] [CrossRef]
  36. Neuner, P.; Graf, D.; Netsch, N.; Zeller, M.; Herrmann, T.-C.; Stapf, D.; Rauch, R. Chemical Conversion of Fischer–Tropsch Waxes and Plastic Waste Pyrolysis Condensate to Lubricating Oil and Potential Steam Cracker Feedstocks. Reactions 2022, 3, 352–373. [Google Scholar] [CrossRef]
  37. Cheng, S.; An, L.; Li, Z.; Liu, S.; Lv, J.; Fan, S.; Zhao, T. Qualitative and quantitative analysis of refined F–T wax on GC–MS and GC. Fuel 2023, 332, 126031. [Google Scholar] [CrossRef]
  38. Teimouri, Z.; Abatzoglou, N.; Dalai, A.K. Design of a renewable catalyst support derived from biomass with optimized textural features for Fischer Tropsch synthesis. Renew. Energy 2023, 202, 1096–1109. [Google Scholar] [CrossRef]
  39. Chen, C.; Hou, B.; Liu, Y.; Jia, L.; Ma, Z.; Wang, J.; Wang, Q.; Li, D. Higher alcohols synthesis via Fischer–Tropsch reaction at hcp-Co@ Co2C interface. Fuel 2023, 341, 127500. [Google Scholar] [CrossRef]
  40. Xu, J.; Wei, J.; Zhang, J.; Liu, N.; Ge, Q.; Sun, J. Precisely synergistic synthesis of higher alcohols from syngas over iron carbides. Chem Catalys. 2023, 100584. [Google Scholar] [CrossRef]
  41. Peppas, A.; Kottaridis, S.; Politi, C.; Angelopoulos, P.M. Carbon Capture Utilisation and Storage in Extractive Industries for Methanol Production. Eng 2023, 4, 29. [Google Scholar] [CrossRef]
  42. Bampaou, M.; Haag, S.; Kyriakides, A.S.; Panopoulos, K.D.; Seferlis, P. Optimizing methanol synthesis combining steelworks off-gases and renewable hydrogen. Renew. Sustain. Energy Rev. 2023, 171, 113035. [Google Scholar] [CrossRef]
  43. Liu, G.; Hagelin-Weaver, H.; Welt, B. A Concise Review of Catalytic Synthesis of Methanol from Synthesis Gas. Waste 2023, 1, 15. [Google Scholar] [CrossRef]
  44. Flórez-Orrego, D.A.; Nakashima, R.N.; Domingos, M.E.G.R.; dos Santos, M.T.; de Oliveira Junior, S. Ammonia production from syngas. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 3, Chapter 3; pp. 45–91. [Google Scholar] [CrossRef]
  45. Baltrusaitis, J. Sustainable ammonia production. ACS Sustain. Chem. Eng. 2017, 5, 9527. [Google Scholar] [CrossRef]
  46. Rossetti, I. Modeling, simulation, and optimization of combined heat and power generation from produced syngas. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 4, Chapter 3; pp. 465–491. [Google Scholar] [CrossRef]
  47. Mahinpey, N.; Farooqui, A.; Abdalla, A.; Asghari, K. Power generation from syngas. In Advances in Synthesis Gas: Methods, Technologies and Applications; Chapter 12; Elsevier: Amsterdam, The Netherlands, 2023; Volume 3, pp. 289–319. [Google Scholar] [CrossRef]
  48. Heo, Y.S.; Jeon, K.W.; Kim, H.M.; Park, M.J.; Cheon, B.S.; Jin, H.D.; Jeong, D.W. Hydrogen production from waste-derived synthesis gas over Ni (x) Fe (3-x)-CeO2 catalyst: Optimization of Ni/Fe ratio. Int. J. Hydrogen Energy 2023. [Google Scholar] [CrossRef]
  49. Roostaie, T.; Abbaspour, M.; Makarem, M.A.; Rahimpour, M.R. Hydrogen production from syngas. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 3, Chapter 2; pp. 27–43. [Google Scholar] [CrossRef]
  50. Jóźwiak, P.; Hercog, J.; Kiedrzyńska, A.; Badyda, K. CFD analysis of natural gas substitution with syngas in the industrial furnaces. Energy 2019, 179, 593–602. [Google Scholar] [CrossRef]
  51. Fronczyk, J.; Pawluk, K.; Michniak, M. Application of permeable reactive barriers near roads for chloride ions removal. Ann. Warsaw Univ. Life Sci. SGGW Land Reclaim. 2010, 42, 249–259. [Google Scholar] [CrossRef]
  52. Fronczyk, J.; Pawluk, K.; Garbulewski, K. Multilayer PRBs—Effective technology for protection of the groundwater environment in traffic infrastructures. Chem. Eng. Trans. 2012, 28, 67–72. [Google Scholar]
  53. Franco Gonzalez, F. Zero-valence iron nanoparticles applied in the desalination of sea water. In Proceedings of the 3rd International Congress on Water, Waste and Energy Management, Rome, Italy, 18–20 July 2016; p. 180. [Google Scholar]
  54. Heder, M. From NASA to EU: The evolution of the TRL scale in Public Sector Innovation. Innov. J. Public Sect. Innov. J. 2017, 22, 3. [Google Scholar]
  55. European Space Agency. Technology Readiness Levels Handbook for Space Applications; TRL Handbook Issue 1 revision 6—September 2008; TEC-SHS/5551/MG/ap. 2008; ESA: Cologne, Germany, 2008. [Google Scholar]
  56. Bhavanam, A.; Sastry, R.C. Modelling of solid waste gasification process for synthesis gas production. J. Sci. Ind. Res. 2013, 72, 611–616. [Google Scholar]
  57. Chen, K.F.; Li, S.; Zhang, W.X. Renewable hydrogen generation by bimetallic zero valent iron nanoparticles. Chem. Eng. J. 2011, 170, 562–567. [Google Scholar] [CrossRef]
  58. Constantinou, D.; Samanides, C.G.; Koutsokeras, L.; Constantinides, G.; Vyrides, I. Hydrogen generation by soluble CO2 reaction with zero-valent iron or scrap iron and the role of weak acids for controlling FeCO3 formation. Sustain. Energy Technol. Assess. 2023, 56, 103061. [Google Scholar] [CrossRef]
  59. Reardon, E.J. Capture and storage of hydrogen gas by zero-valent iron. J. Contam. Hydrol. 2014, 157, 117–124. [Google Scholar] [CrossRef]
  60. Xiao, C.X.; Cai, Z.P.; Wang, T.; Kou, Y.; Yan, N. Aqueous-Phase Fischer–Tropsch Synthesis with a Ruthenium Nanocluster Catalyst. Angew. Chem. Int. Ed. 2008, 47, 746–749. [Google Scholar] [CrossRef]
  61. Liu, L.; Sun, G.; Wang, C.; Yang, J.; Xiao, C.; Wang, H.; Ma, D.; Kou, Y. Aqueous phase Fischer–Tropsch synthesis in a continuous flow reactor. Catal. Today 2012, 183, 136–142. [Google Scholar] [CrossRef]
  62. Wang, C.; Zhao, H.; Wang, H.; Liu, L.; Xiao, C.; Ma, D. The effects of ionic additives on the aqueous-phase Fischer–Tropsch synthesis with a ruthenium nanoparticle catalyst. Catal. Today 2012, 183, 143–153. [Google Scholar] [CrossRef]
  63. Wieland, E.; Hummel, W. Formation and stability of 14C-containing organic compounds in alkaline iron-water systems: Preliminary assessment based on a literature survey and thermodynamic modelling. Mineral. Mag. 2015, 79, 1275–1286. [Google Scholar] [CrossRef]
  64. Mousavi, S.; Zamaniyan, A.; Irani, M.; Rashidzadeh, M. Generalized kinetic model for iron and cobalt based Fischer–Tropsch synthesis catalysts: Review and model evaluation. Appl. Catal. A Gen. 2015, 506, 57–66. [Google Scholar] [CrossRef]
  65. Pendyala, V.R.R.; Shafer, W.D.; Jacobs, G.; Davis, B.H. Fischer–Tropsch synthesis: Effect of reaction temperature for aqueous-phase synthesis over a platinum promoted Co/alumina catalyst. Catal. Lett. 2014, 144, 1088–1095. [Google Scholar] [CrossRef]
  66. Bennett, P.; He, F.; Zhao, D.; Aiken, B.; Feldman, L. In situ testing of metallic iron nanoparticle mobility and reactivity in a shallow granular aquifer. J. Contam. Hydrol. 2010, 116, 35–46. [Google Scholar] [CrossRef]
  67. Liu, Y.; Majetich, S.A.; Tilton, R.D.; Sholl, D.S.; Lowry, G.V. TCE dechlorination rates, pathways, and efficiency of nanoscale iron particles with different properties. Environ. Sci. Technol. 2005, 39, 1338–1345. [Google Scholar] [CrossRef]
  68. Hardy, L.I.; Gillham, R.W. Formation of hydrocarbons from the reduction of aqueous CO2 by zero-valent iron. Environ. Sci. Technol. 1995, 30, 57–65. [Google Scholar] [CrossRef]
  69. Deng, B.; Campbell, T.J.; Burris, D.R. Hydrocarbon formation in metallic iron/water systems. Environ. Sci. Technol. 1997, 31, 1185–1190. [Google Scholar] [CrossRef]
  70. Cvetković, B.Z.; Rothardt, J.; Büttler, A.; Kunz, D.; Schlotterbeck, G.; Wieland, E. Formation of low-molecular-weight organic compounds during anoxic corrosion of zero-valent iron. Environ. Eng. Sci. 2018, 35, 447–461. [Google Scholar] [CrossRef]
  71. Guillemot, T.; Cvetković, B.Z.; Kunz, D.; Wieland, E. Processes leading to reduced and oxidised carbon compounds during corrosion of zero-valent iron in alkaline anoxic conditions. Chemosphere 2020, 250, 126230. [Google Scholar] [CrossRef]
  72. Guillemot, T.; Salazar, G.; Rauber, M.; Kunz, D.; Szidat, S.; Wieland, E. Carbon-14 release and speciation during corrosion of irradiated steel under radioactive waste disposal conditions. Sci. Total Environ. 2022, 817, 152596. [Google Scholar] [CrossRef]
  73. Yang, X.; Zhang, H.; Liu, Y.; Ning, W.; Han, W.; Liu, H.; Huo, C. Preparation of Iron Carbides Formed by Iron Oxalate Carburization for Fischer–Tropsch Synthesis. Catalysts 2019, 9, 347. [Google Scholar] [CrossRef]
  74. Rommens, K.T.; Saeys, M. Molecular Views on Fischer–Tropsch Synthesis. Chem. Rev. 2023. [Google Scholar] [CrossRef] [PubMed]
  75. Okonye, L.U.; Yao, Y.; Ren, J.; Liu, X.; Hildebrandt, D. A perspective on the activation energy dependence of the Fischer-Tropsch synthesis reaction mechanism. Chem. Eng. Sci. 2023, 265, 118259. [Google Scholar] [CrossRef]
  76. Bottero, J.Y.; Manceau, A.; Villieras, F.; Tchoubar, D. Structure and mechanisms of formation of iron oxide hydroxide (chloride) polymers. Langmuir 1994, 10, 316–319. [Google Scholar] [CrossRef]
  77. Spiro, T.G.; Allerton, S.E.; Renner, J.; Terzis, A.; Bils, R.; Saltman, P. The Hydrolytic Polymerization of Iron(III). J. Am. Chem. Soc. 1966, 88, 2721–2726. [Google Scholar] [CrossRef]
  78. Dong, H.; Gao, B.; Yue, Q.; Sun, S.; Wang, Y.; Li, Q. Floc properties and membrane fouling of different monomer and polymer Fe coagulants in coagulation–ultrafiltration process: The role of Fe (III) species. Chem. Eng. J. 2014, 258, 442–449. [Google Scholar] [CrossRef]
  79. Chen, D.-W.; Liu, C.; Lu, J.; Mehmood, T.; Ren, Y.-Y. Enhanced phycocyanin and DON removal by the synergism of H2O2 and micro-sized ZVI: Optimization, performance, and mechanisms. Sci. Total Environ. 2020, 738, 140134. [Google Scholar] [CrossRef]
  80. Maryanti, R.; Hufad, A.; Nandiyanto, A.B.D.; Tukimin, S. Teaching the corrosion of iron particles in saline water to students with special needs. J. Eng. Sci. Technol. 2021, 16, 601–611. [Google Scholar]
  81. Tang, Z.; Hong, S.; Xiao, W.; Taylor, J. Characteristics of iron corrosion scales established under blending of ground, surface, and saline waters and their impacts on iron release in the pipe distribution system. Corros. Sci. 2006, 48, 322–342. [Google Scholar] [CrossRef]
  82. Ali, N.; Fulazzaky, M.A. The empirical prediction of weight change and corrosion rate of low-carbon steel. Heliyon 2020, 6, e05050. [Google Scholar] [CrossRef]
  83. Krietsch, A.; Scheid, M.; Schmidt, M.; Krause, U. Explosion behaviour of metallic nano powders. J. Loss Prev. Process Ind. 2015, 36, 237–243. [Google Scholar] [CrossRef]
  84. Huber, D.L. Synthesis, properties, and applications of iron nanoparticles. Small 2005, 1, 482–501. [Google Scholar] [CrossRef] [PubMed]
  85. Ebbing, D.D.; Gammon, S.D. General Chemistry; Houghton Mifflin Company: New York, NY, USA, 2005; ISBN 0-618-399410. [Google Scholar]
  86. Refait, P.; Génin, J.M. The oxidation of ferrous hydroxide in chloride-containing aqueous media and Pourbaix diagrams of green rust one. Corros. Sci. 1993, 34, 797–819. [Google Scholar] [CrossRef]
  87. Refait, P.H.; Abdelmoula, M.; Génin, J.M. Mechanisms of formation and structure of green rust one in aqueous corrosion of iron in the presence of chloride ions. Corros. Sci. 1998, 40, 1547–1560. [Google Scholar] [CrossRef]
  88. Sagoe-Crentsil, K.K.; Glasser, F.P. “Green rust”, iron solubility and the role of chloride in the corrosion of steel at high pH. Cem. Concr. Res. 1993, 23, 785–791. [Google Scholar] [CrossRef]
  89. Génin, J.M.; Refait, P.; Simon, L.; Drissi, S.H. Preparation and Eh--pH diagrams of Fe (II)--Fe (III) green rust compounds; hyperfine interaction characteristics and stoichiometry of hydroxy-chloride,-sulphate and-carbonate. Hyperfine Interact. 1998, 111, 313–318. [Google Scholar] [CrossRef]
  90. Cai, J.; Liu, J.; Gao, Z.; Navrotsky, A.; Suib, S.L. Synthesis and anion exchange of tunnel structure akaganeite. Chem. Mater. 2001, 13, 4595–4602. [Google Scholar] [CrossRef]
  91. Rémazeilles, C.; Refait, P. On the formation of β-FeOOH (akaganéite) in chloride-containing environments. Corros. Sci. 2007, 49, 844–857. [Google Scholar] [CrossRef]
  92. Post, J.E.; Buchwald, V.F. Crystal structure refinement of akaganeite. Am. Mineral. 1991, 76, 272–277. [Google Scholar]
  93. Scheck, J.; Lemke, T.; Gebauer, D. The Role of Chloride Ions during the Formation of Akaganéite Revisited. Minerals 2015, 5, 778–787. [Google Scholar] [CrossRef]
  94. Bakry, A.M.; Alamier, W.M.; Salama, R.S.; El-Shall, M.S.; Awad, F.S. Remediation of water containing phosphate using ceria nanoparticles decorated partially reduced graphene oxide (CeO2-PRGO) composite. Surf. Interfaces 2022, 31, 102006. [Google Scholar] [CrossRef]
  95. Ibrahim, A.A.; Salama, R.S.; El-Hakam, S.A.; Khder, A.S.; Ahmed, A.I. Synthesis of 12-tungestophosphoric acid supported on Zr/MCM-41 composite with excellent heterogeneous catalyst and promising adsorbent of methylene blue. Colloids Surf. A Physicochem. Eng. Asp. 2021, 631, 127753. [Google Scholar] [CrossRef]
  96. Kokalj, A. On the use of the Langmuir and other adsorption isotherms in corrosion inhibition. Corros. Sci. 2023, 217, 111112. [Google Scholar] [CrossRef]
  97. Kokalj, A. A general-purpose adsorption isotherm for improved estimation of standard adsorption free energy. Corros. Sci. 2023, 217, 111124. [Google Scholar] [CrossRef]
  98. Rudd, D.W.; Vose, D.W.; Johnson, S. The permeability of copper to hydrogen. J. Phys. Chem. 1961, 65, 1018–1020. [Google Scholar] [CrossRef]
  99. Ehrmann, F.M.; Gajardo, P.S.; Droguett, S.C. Permeability of copper and nickel-copper membranes to hydrogen. J. Phys. Chem. 1973, 77, 2146–2148. [Google Scholar] [CrossRef]
  100. Louthan, M.R., Jr.; Caskey, G.R., Jr. Hydrogen transport and embrittlement in structural metals. Int. J. Hydrogen Energy 1976, 1, 291–305. [Google Scholar] [CrossRef]
  101. Lak, S.Z.; Bonyadi, M.; Rahimpour, M.R. Syngas from agricultural waste. In Advances in Synthesis Gas: Methods, Technologies and Applications; Elsevier: Amsterdam, The Netherlands, 2023; Volume 1, Chapter 16; pp. 379–409. [Google Scholar]
  102. British Standards Institute. Quality management systems, BSI Handbook 25. In Statistical Interpretation of Data; British Standards Institute: London, UK, 1985; p. 318. ISBN 0580150712/9780580150715. [Google Scholar]
  103. Schober, P.; Boer, C.; Schwarte, L.A. Correlation Coefficients: Appropriate Use and Interpretation. Anesth. Analg. 2018, 126, 1763–1768. [Google Scholar] [CrossRef]
  104. Taylor, R. Interpretation of the Correlation Coefficient: A Basic Review. J. Diagn. Med. Sonogr. 1990, 6, 35–39. [Google Scholar] [CrossRef]
  105. Terreni, J.; Trottmann, M.; Franken, T.; Heel, A.; Borgschulte, A. Sorption-Enhanced Methanol Synthesis. Energy Technol. 2019, 7, 1801093. [Google Scholar] [CrossRef]
  106. Chatsiriwech, D.; Alpaya, E.; Kershenbaum, L.S.; Hull, C.P.; Kirkby, N.F. Enhancement of catalytic reaction by pressure swing adsorption. Catal. Today 1994, 20, 351–366. [Google Scholar] [CrossRef]
  107. Wellington, S.N.; Cooper, W.R. Low Temperature Carbonisation; Charles Griffin and Company Ltd.: London, UK, 1924; p. 238. [Google Scholar]
  108. Snavely, K.; Subramaniam, B. Thermal conductivity detector analysis of hydrogen using helium carrier gas and Hayesep® D columns. J. Chromatogr. Sci. 1998, 36, 191–196. [Google Scholar] [CrossRef]
  109. Storch, H.H.; Golumbic, N.; Anderson, R.B. The Fischer-Tropsch and Related Synthesis; John Wiley & Sons Inc.: New York, NY, USA, 1951; p. 610. [Google Scholar]
  110. Xiaomin, N.; Xiaobo, S.; Huagui, Z.; Dongen, Z.; Dandan, Y.; Qingbiao, Z. Studies on the one-step preparation of iron nanoparticles in solution. J. Cryst. Growth 2005, 275, 548–553. [Google Scholar] [CrossRef]
  111. Guisbiers, G. Schottky Defects in Nanoparticles. J. Phys. Chem. C 2011, 115, 2616–2621. [Google Scholar] [CrossRef]
  112. Schilling, W. Properties of Frenkel defects. J. Nucl. Mater. 1994, 216, 45–48. [Google Scholar] [CrossRef]
  113. Murzin, D.Y. On Langmuir kinetics and zero order reactions. Catal. Commun. 2008, 9, 1815–1816. [Google Scholar] [CrossRef]
  114. Jayaraman, V. Effectiveness of biporous catalysts for zero-order reactions. J. Catal. 1992, 133, 260–262. [Google Scholar] [CrossRef]
  115. Biloen, P.; Helle, J.N.; Sachtler, W.M.H. Incorporation of surface carbon into hydrocarbons during Fischer-Tropsch synthesis: Mechanistic implications. J. Catal. 1979, 58, 95–107. [Google Scholar] [CrossRef]
  116. Huo, C.F.; Li, Y.W.; Wang, J.; Jiao, H. Insight into CH4 formation in iron-catalyzed Fischer—Tropsch synthesis. J. Am. Chem. Soc. 2009, 131, 14713–14721. [Google Scholar] [CrossRef]
  117. Ming, H.; Baker, B.G. Characterization of cobalt Fischer-Tropsch catalysts I. Unpromoted cobalt-silica gel catalysts. Appl. Catal. A Gen. 1995, 123, 23–36. [Google Scholar] [CrossRef]
  118. Sircar, S.; Golden, T.C. Purification of hydrogen by pressure swing adsorption. Sep. Sci. Technol. 2000, 35, 667–687. [Google Scholar] [CrossRef]
  119. Malek, A.; Farooq, S. Hydrogen purification from refinery fuel gas by pressure swing adsorption. AIChE J. 1998, 44, 1985–1992. [Google Scholar] [CrossRef]
  120. Nagai, S.; Arai, H.; Hatada, M. Radiation effects on CO: H2 gas mixture in the presence of silica gel. Radiat. Phys. Chem. 1980, 16, 175–181. [Google Scholar] [CrossRef]
Figure 1. Feedstock, synthesis gas composition, and end products associated with waste synthesis gas.
Figure 1. Feedstock, synthesis gas composition, and end products associated with waste synthesis gas.
Waste 01 00026 g001
Figure 2. FT analysis of hydrocarbon generation associated with desalination pellet formation. (a) Proportion of CO + CH4 in the feed gas converted to C2+ hydrocarbons during the formation of the desalination pellets; (b) relationship between Ln (Arrhenius Factor) and Activation Energy as a function of temperature. Red = aqueous production at 283 K (Route 1); total reaction time = 29.5 min; total reaction time = the time spent by the gas within the reaction environment. Purple, green, and blue = conventional Fischer–Tropsch plants operated at 433 K, 483 K, and 533 K, respectively. Background = Fe0 particles in water.
Figure 2. FT analysis of hydrocarbon generation associated with desalination pellet formation. (a) Proportion of CO + CH4 in the feed gas converted to C2+ hydrocarbons during the formation of the desalination pellets; (b) relationship between Ln (Arrhenius Factor) and Activation Energy as a function of temperature. Red = aqueous production at 283 K (Route 1); total reaction time = 29.5 min; total reaction time = the time spent by the gas within the reaction environment. Purple, green, and blue = conventional Fischer–Tropsch plants operated at 433 K, 483 K, and 533 K, respectively. Background = Fe0 particles in water.
Waste 01 00026 g002
Figure 3. 15 mm O.D. copper pipe showing the effects of hydrogen leakage when the pipe (rated to 2 MPa water pressure) is pressured with a gas containing hydrogen at 0.1 to 0.3 MPa. Blue-green patches are formed by Cu(OH)x as the hydrogen reacts with both oxygen in the air and the Cu0 at leakage points.
Figure 3. 15 mm O.D. copper pipe showing the effects of hydrogen leakage when the pipe (rated to 2 MPa water pressure) is pressured with a gas containing hydrogen at 0.1 to 0.3 MPa. Blue-green patches are formed by Cu(OH)x as the hydrogen reacts with both oxygen in the air and the Cu0 at leakage points.
Waste 01 00026 g003
Figure 4. Design concept. Copper central tubing: inner shell and inner annulus. Blue = outer annulus of the outer shell. It receives hydrogen through the wall of the inner shell from the inner annulus. Red = bunding shell of the reactor. Arrow indicates direction of gas flow within the inner annulus.
Figure 4. Design concept. Copper central tubing: inner shell and inner annulus. Blue = outer annulus of the outer shell. It receives hydrogen through the wall of the inner shell from the inner annulus. Red = bunding shell of the reactor. Arrow indicates direction of gas flow within the inner annulus.
Waste 01 00026 g004
Figure 5. Process design concept for the monetisation of waste synthesis gas (WSG). Reactor R1 complex (this study); reactor R2 complex (reactor converting COx to products, including oxygenates); WG = waste gas. Background = particles held in the fixed-bed reactor (Fe0-coated halite grains and silica gel particles (largest particle = 5 mm)).
Figure 5. Process design concept for the monetisation of waste synthesis gas (WSG). Reactor R1 complex (this study); reactor R2 complex (reactor converting COx to products, including oxygenates); WG = waste gas. Background = particles held in the fixed-bed reactor (Fe0-coated halite grains and silica gel particles (largest particle = 5 mm)).
Waste 01 00026 g005
Figure 6. Conceptual process design for the RPSAD reactor train used to construct the desalination pellets (Route 2). The term ZVI is used to refer to a mixture of zero-valent metals, where the dominant metal is Fe0.
Figure 6. Conceptual process design for the RPSAD reactor train used to construct the desalination pellets (Route 2). The term ZVI is used to refer to a mixture of zero-valent metals, where the dominant metal is Fe0.
Waste 01 00026 g006
Figure 7. Reactor elements. (a) Flow controller; (b) gas sampling point; all compression seals in the reactor were sealed with Gas PTFE tape (supplied by Screwfix Ltd., Perth; the Shimadzu, BTO, and septa were supplied by Cole Parmer); (c) part of the DSA.
Figure 7. Reactor elements. (a) Flow controller; (b) gas sampling point; all compression seals in the reactor were sealed with Gas PTFE tape (supplied by Screwfix Ltd., Perth; the Shimadzu, BTO, and septa were supplied by Cole Parmer); (c) part of the DSA.
Waste 01 00026 g007
Figure 8. Reactor train structure.
Figure 8. Reactor train structure.
Waste 01 00026 g008
Figure 9. Reactor configuration: (a) FBR containing a 12 m particulate column; (b) configuration used in this study of a FBR constructed from two 3 m-long pipe segments and the BCDR. Note the pipe sections which have a white colour. These are sections which are associated with significant hydrogen discharge through the pipe wall.
Figure 9. Reactor configuration: (a) FBR containing a 12 m particulate column; (b) configuration used in this study of a FBR constructed from two 3 m-long pipe segments and the BCDR. Note the pipe sections which have a white colour. These are sections which are associated with significant hydrogen discharge through the pipe wall.
Waste 01 00026 g009
Figure 10. Examples of freshly cut desalination pellets.
Figure 10. Examples of freshly cut desalination pellets.
Waste 01 00026 g010
Figure 11. Evidence of hydrogen leakage through the Cu0 pipes. (a) Cu(OH)2 precipitates at hydrogen gas discharge points; (b) Cu(OH) and Cu(OH)2 precipitates on a Cu0 pipe.
Figure 11. Evidence of hydrogen leakage through the Cu0 pipes. (a) Cu(OH)2 precipitates at hydrogen gas discharge points; (b) Cu(OH) and Cu(OH)2 precipitates on a Cu0 pipe.
Waste 01 00026 g011
Figure 12. Cylindrical porous C0@Fe0:Fe(a,b,c) pellet immediately after manufacture. White patches indicate the presence of Fe0 and sites which will form Fe(a,b,c) polymers following immersion in water. Reflected light. Field of view = 0.267 mm.
Figure 12. Cylindrical porous C0@Fe0:Fe(a,b,c) pellet immediately after manufacture. White patches indicate the presence of Fe0 and sites which will form Fe(a,b,c) polymers following immersion in water. Reflected light. Field of view = 0.267 mm.
Waste 01 00026 g012
Figure 13. Desalination pellet. (a) Cross-section through a 15 mm O.D. pellet; (b) salinity versus hours; (c) Eh versus hours; (d) pH versus hours; (e) Eh versus pH.
Figure 13. Desalination pellet. (a) Cross-section through a 15 mm O.D. pellet; (b) salinity versus hours; (c) Eh versus hours; (d) pH versus hours; (e) Eh versus pH.
Waste 01 00026 g013
Figure 14. Active carbon-n-Fe0 pellet operation. (a) Salinity versus time; (b) recovered pellet; white = precipitated NaCl within the pellet’s porosity. Reflected light. Field of view = 0.26 mm. Reaction order over the first 400 h is second order based on a regression analysis of a cross-plot of time versus 1/salinity. 1/salinity = 0.000317 (hours) + 0.45693; R2 = 0.952.
Figure 14. Active carbon-n-Fe0 pellet operation. (a) Salinity versus time; (b) recovered pellet; white = precipitated NaCl within the pellet’s porosity. Reflected light. Field of view = 0.26 mm. Reaction order over the first 400 h is second order based on a regression analysis of a cross-plot of time versus 1/salinity. 1/salinity = 0.000317 (hours) + 0.45693; R2 = 0.952.
Waste 01 00026 g014
Table 1. Material placed in the EPB (BCDR) and USA (FBR). Ca-M = Ca-montmorillonite. All amounts are in grams. USA length = 6 m. Water column length above the gas distributer in the EPB = 7.5 m (2.38 L). Concentrations in the EPB are expressed in g L−1.
Table 1. Material placed in the EPB (BCDR) and USA (FBR). Ca-M = Ca-montmorillonite. All amounts are in grams. USA length = 6 m. Water column length above the gas distributer in the EPB = 7.5 m (2.38 L). Concentrations in the EPB are expressed in g L−1.
NaClFe0Cu0Al0KClSilica GelK2SO4FeSO4Ca-M
USA303102.411.1031.1220.532.8954.40
EPB8.836.14.46.3000013.9
Table 2. Circular (catalytic) process for the formation of C2H2 from CO2.
Table 2. Circular (catalytic) process for the formation of C2H2 from CO2.
C1NaCl + CO2 + H2O = HCl + NaHCO3
C2NaHCO3 + H2 = H2O + NaHCO2
C3HCl + NaHCO2 = NaCl + HCOOH
C4CO2 + HCOOH + 6H2 = 4H2O + C2H6
Table 3. Molar product gas compositions exiting the FBR, normalized to the nitrogen content of the feed gas.
Table 3. Molar product gas compositions exiting the FBR, normalized to the nitrogen content of the feed gas.
H2N2COCO2CH4C2+
Feed16.88%46.03%8.33%11.97%16.79%0.00%
Product
Mean0.80%46.03%6.10%6.03%7.36%0.13%
Standard Deviation0.48%0.00%4.75%4.56%5.43%0.11%
Minimum0.25%46.03%0.00%0.06%0.00%0.00%
1st Quartile0.51%46.03%2.04%1.99%2.62%0.05%
Median0.71%46.03%4.35%4.59%5.59%0.09%
3rd Quartile0.89%46.03%10.69%10.77%12.93%0.19%
Maximum4.20%46.03%13.28%19.19%15.19%0.48%
Table 4. Molar product gas compositions exiting the BCDR, normalized to the nitrogen content of the feed gas.
Table 4. Molar product gas compositions exiting the BCDR, normalized to the nitrogen content of the feed gas.
H2N2COCO2CH4C2+
Feed from FBR0.80%46.03%6.10%6.03%7.36%0.13%
Product
Mean1.51%46.03%9.92%9.29%11.59%0.16%
Standard Deviation3.40%0.00%4.38%4.38%5.01%0.50%
Minimum0.41%46.03%0.00%0.06%0.00%0.00%
1st Quartile0.95%46.03%8.02%5.64%10.19%0.05%
Median1.07%46.03%12.50%11.61%14.60%0.08%
3rd Quartile1.25%46.03%12.94%12.39%14.92%0.15%
Maximum41.49%46.03%15.03%19.19%16.03%9.02%
Table 5. Molar product C2+ hydrocarbon compositions exiting the BCDR, where the sum of the C2+ hydrocarbons = 100%.
Table 5. Molar product C2+ hydrocarbon compositions exiting the BCDR, where the sum of the C2+ hydrocarbons = 100%.
EthyneEtheneEthanePropynePropenePropaneButyneButeneButanePentenePentane
Mean78.5%10.3%7.5%2.1%0.9%0.2%0.2%0.1%0.1%0.0%0.0%
Standard Deviation29.9%16.1%15.3%7.1%4.0%1.9%2.0%0.7%0.9%0.3%0.4%
Minimum0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%
1st Quartile58.1%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%
Median100.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%
3rd Quartile100.0%15.3%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%0.0%
Maximum100.0%76.1%74.0%78.5%30.9%25.9%20.2%11.7%17.6%6.1%8.4%
Table 6. Statistical analysis of Route 2 desalination pellet performance. Rate constants are determined as zero order constants [85]. The associated time unit is seconds. Sample size = 25 tests. Reaction time = 4239 h.
Table 6. Statistical analysis of Route 2 desalination pellet performance. Rate constants are determined as zero order constants [85]. The associated time unit is seconds. Sample size = 25 tests. Reaction time = 4239 h.
Feed WaterProduct WaterFe:Fe(a,b,c)@C0Log10 Zero OrderLog10 Zero OrderDesalination
g NaCl L−1g NaCl L−1g L−1Rate ConstantRate Constant g−1(1 − (Product/Feed))
Mean8.823.4655.87−6.4589−7.494560.68%
Standard Deviation0.300.7614.270.05790.10628.47%
Minimum8.480.5335.95−6.5372−7.776549.55%
1st Quartile8.483.3346.20−6.4934−7.561557.78%
Median8.943.4950.25−6.4692−7.471460.02%
3rd Quartile8.943.7365.25−6.4354−7.432662.75%
Maximum9.244.5194.20−6.2435−7.304294.26%
Table 7. Statistical analysis of Route 2 desalination pellet performance. Rate constants are determined as zero order constants [85]. The associate time unit is seconds. Sample size = 25 tests. Reaction time = 4215 h.
Table 7. Statistical analysis of Route 2 desalination pellet performance. Rate constants are determined as zero order constants [85]. The associate time unit is seconds. Sample size = 25 tests. Reaction time = 4215 h.
Feed WaterProduct WaterFe:Fe(a,b,c)@C0Log10 Zero OrderLog10 Zero OrderDesalination
g NaCl L−1g NaCl L−1g L−1Rate ConstantRate Constant g−1(1 − (Product/Feed))
Mean7.782.7433.72−6.4799−7.284562.35%
Standard Deviation1.810.6513.650.13740.262713.21%
Minimum4.410.7123.30−6.7475−7.939438.78%
1st Quartile7.602.6326.50−6.4865−7.276761.15%
Median8.832.7030.10−6.4384−7.189165.13%
3rd Quartile8.833.0733.50−6.4125−7.145367.42%
Maximum9.243.5979.60−6.2718−6.970491.91%
Table 8. FT hydrocarbon produced from C0.
Table 8. FT hydrocarbon produced from C0.
F1C0(s) + H(ads) = CH(ads)
F2CH(ads) + H(ads) = CH2(ads)
F3CH2(ads) + H(ads) = CH3(ads)
F4CH3(ads) + H(ads) = CH4(g)
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Antia, D.D.J. Conversion of Waste Synthesis Gas to Desalination Catalyst at Ambient Temperatures. Waste 2023, 1, 426-454. https://doi.org/10.3390/waste1020026

AMA Style

Antia DDJ. Conversion of Waste Synthesis Gas to Desalination Catalyst at Ambient Temperatures. Waste. 2023; 1(2):426-454. https://doi.org/10.3390/waste1020026

Chicago/Turabian Style

Antia, David D. J. 2023. "Conversion of Waste Synthesis Gas to Desalination Catalyst at Ambient Temperatures" Waste 1, no. 2: 426-454. https://doi.org/10.3390/waste1020026

Article Metrics

Back to TopTop