Next Article in Journal
Gas-Liquid Hollow Fiber Membrane Contactors for Different Applications
Previous Article in Journal
Geometry of Chalcogenide Negative Curvature Fibers for CO2 Laser Transmission
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Modeling of Coupled Heat and Mass Transfers in a Stabilized Earthen Building Envelope with Thatched Fibers

1
Environmental Energy Technologies Laboratory (EETL), Department of Physics, Faculty of Science, University of Yaounde I, P.O. Box 812 Yaounde, Cameroon
2
School of Geology and Mining Engineering, Department of Basic Scientific Teaching, University of Ngaoundere, P.O. Box 454 Ngaoundere, Cameroon
3
Laboratory of Energy, Water and Environment (L3E), National Advanced School of Engineering, Yaoundé, P.O. Box 8390 Yaounde, Cameroon
4
Department of Physics, Higher Teachers’ Training College, University of Maroua, P.O. Box 55 Maroua, Cameroon
*
Author to whom correspondence should be addressed.
Fibers 2018, 6(4), 75; https://doi.org/10.3390/fib6040075
Submission received: 10 August 2018 / Revised: 14 September 2018 / Accepted: 29 September 2018 / Published: 2 October 2018

Abstract

:
In order to reduce the heat and mass transfers in buildings, which increase energy bills, the development of composites materials such as earth bricks stabilized with thatch fibers is important for their construction. This paper aims to study a one-dimensional model of heat and moisture transfer through porous building materials. The coupled phenomena of heat and mass transfer are described by the Luikov model. Equations and boundary conditions are discretized using the finite difference method. The results obtained illustrate the temporal evolutions of the temperature and the moisture content, as well as the distributions of the temperature and moisture content inside the wall. The profile of the temperature and water content that are obtained are compared with the other numerical solutions that are available in the literature.

1. Introduction

Plant waste is valued in various ways in rural areas of Adamawa region in Cameroon. For instance, thatch fibers are used to cover the roofs because they offer good thermal insulation of the premises [1]. Concerning building envelopes, composite materials are used to improve the performance of simple brick. Meukam et al. [2] have shown that the incorporation of pozzolan or sawdust in laterite decreases the thermal conductivity and the density of the material, thus improving the thermal comfort in the habitat. Likewise, the addition of fibers in earth bricks varies their thermophysical properties [3]. The materials that are used as building envelopes are subjected to atmospheric conditions such as rain, wind, and solar radiation [4].There is a relationship between humidity, air, and heat transfer that impacts moisture accumulation in the wall. This influences the suitability of building materials in providing good thermal comfort [5,6,7]. These phenomena reveal a practical importance in the choice of materials for building construction. Sotehi et al. [8] have shown that fiber dosage influences mass transfer. For this reason, the dosage of thatched fibers in the materials shall be considered so that their hydrothermal properties can meet construction standards.
Several works have been done in order to track the evolution of moisture in buildings. To solve the equations governing this phenomenon, some authors use the analytical method [6,7,9] while others prefer numerical solutions [8,10,11,12]. Philip and DeVries [12] developed a model explaining the movement of moisture in porous media under the influence of a temperature gradient. Tamene et al. [13] proposed a numerical model for heat and moisture diffusion through a wall exposed to solar heat flux, based on the finite difference method. As we intend to do, their study showed that it is possible to select and optimize the materials that make up the wall. Meukam [11] investigated a model of heat and mass transfers in a building envelope stabilized with earth bricks. He evaluated the temperature, relative humidity, and water content profiles in building envelopes made of the tested local materials. Therefore, it is therefore to study both heat and mass transfer through this kind of composite material.
The objective of our work is to study the evolution of heat and moisture in earth bricks stabilized with thatched fibers according to their dosage in this building material. After the discretization of the thermal and mass balance equations, a numerical code is developed and applied to four types of walls with different thatched fiber percentages. The spatial and temporal evolutions of the water content and the temperature within the material are studied, as well as the influence of the fiber dosage on transfers.

2. Materials and Methods

The materials used in this study consist of laterite mixed with thatch fibers. All of the samples have same dimensions: 10 cm × 10 cm × 3 cm. The fiber content is 0%, 1%, 2%, and 3% for E0, E1, E2, and E3 samples, respectively. Table 1 below presents the thermophysical properties of these composite materials.The measurements of thermophysical properties such as thermal conductivity and thermal diffusivity are obtained using the asymmetric hot plane method. It’s a transient characterization approach that is used to get these properties [14]. In that study, the thermal conductivity of the composite material remains constant, starting from 4% of thatched fiber addition.

3. Formulation of the Problem

The stabilized earth brick with thatched fibers that is used in this study as a building envelope is a porous material containing water in liquid or gaseous phase. The internal and external faces are at different temperatures. This results in conductive heat transfer through the material and heat transfer accompanying each phase change. The mathematical modeling of the thermomigration phenomenon that occurs within the material is done from a macroscopic approach that consists of introducing the experimental physical laws of the elementary processes in the heat mass conservation relations. The model that is applied to the materials is that of Philip [12]. It is based on the work of Luikov [15]. It predicts the distribution of temperature and water content in porous material. The mass balance and energy equations are given by the following expressions:
  ρ 0 C P T t = x ( λ T x ) + ε L V ρ 0 θ t  
  θ t = ( D θ + D δ T )  
where T represents the temperature, x is the space variable, θ is the water content, t is the time variable, ρ 0 is the material density, C p is the heat capacity, λ is the thermal conductivity, ε is the phase-change coefficient, L v is the latent heat of vaporization, D is the moisture diffusivity, and δ is the thermomigration coefficient.
By rearranging Equations (1) and (2), we respectively obtain Equations (3) and (4):
T t = ( λ + ε L V ρ 0 D ) ρ 0 C p 2 T x 2 + ε L V D C p 2 θ x 2  
θ t = D 2 θ x 2 + D δ 2 T x 2  
Let D T = λ + ε L v ρ 0 D ρ O C p   and   D θ = ε L v D C p  
We obtain the following Equations (5) and (6):
T t = D T 2 T x 2 + D θ 2 θ x 2  
θ t = D 2 θ x 2 + D δ 2 T x 2  

3.1. Initial Conditions

The initial temperature and moisture value in the building material are defined by Equation (7):
T ( x , 0 ) = T 0   ;   θ ( x , 0 ) = θ 0   at   ( t = 0 )

3.2. Boundary Conditions

Outdoor conditions depend on several parameters such as rain, wind, or solar irradiation. The associated boundary conditions are illustrated in Figure 1.
For mass transfer:
  x = 0   : ρ 0 D T x ρ 0 D θ x = h m 1 ( ρ 1 ρ 1 )  
  x = e   : ρ 0 D T x ρ 0 D θ x = h m 2 ( ρ 2 ρ 2 )  
For heat transfer:
  x = 0   : λ T x ρ 0 D T x ρ 0 L V D θ x = h 1 ( T f 1 T ( 0 ) )  
  x = e   : λ T x ρ 0 L V D T x ρ 0 L V D θ x = h 2 ( T ( e ) T f 2 )  
The mass convection coefficients h m 1 and h m 2 are deduced from the thermal convection coefficients h 1 and h 2 by the Lewis relation giving by the following expression: h m = h c ρ C p [16].
The mass densities ρ 1 , ρ 1 , ρ 2 , and ρ 2 are determined from the following equations:
  ρ = P R h T w i t h R h = R s 1 ( θ P s a t P ) ( 1 R s R v )  
R s = 287.06   J / k g · K is the universal gas constant of dry air, R v = 461   J / k g · K is the universal gas constant of water vapor, P is the pressure, and Psat is the saturated vapor pressure.
The saturated vapor pressure P s a t is determined by the Magnus formula [17]:
  P s a t = 611.213 × e x p ( 17.5043 T 241.2 + T )  
We finally obtained:
  ρ ( θ , T , P ) = 1 A [ P θ × e x p ( C T D + T ) ]  
where A = 287.06 × ( T + 273.15 ) , B = 230.617 , C = 17.5043 , and D = 241.2 .

4. Numerical Resolution

Applying a finite difference spatial discretization for the left-hand side of Equations (5) and (6), and the Crank–Nicolson method for the right-hand side of the same equations, we have:
T i j + 1 T i j Δ t = D T 2 Δ x 2 ( ( T i + 1 j + 1 2 T i j + 1 + T i 1 j + 1 ) + ( T i + 1 j 2 T i j + T i 1 j ) ) + D θ 2 Δ x 2 ( ( θ i + 1 j + 1 2 θ i j + 1 + θ i 1 j + 1 ) + ( θ i + 1 j 2 θ i j + θ i 1 j ) )  
Hence , α = D T Δ t 2 Δ x 2   and   β = D θ Δ t 2 Δ x 2 ( 1 + 2 α ) T i j + 1 α T i + 1 j + 1 α T i 1 j + 1 β θ i + 1 j + 1 + 2 β θ i j + 1 β θ i 1 j + 1 = ( 1 2 α ) T i j + α T i + 1 j + α T i 1 j + β θ i + 1 j 2 β θ i j + β θ i 1 j  
θ i j + 1 θ i j Δ t = D 2 Δ x 2 ( ( θ i + 1 j + 1 2 θ i j + 1 + θ i 1 j + 1 ) + ( θ i + 1 j 2 θ i j + θ i 1 j ) ) + D δ 2 Δ x 2 ( ( T i + 1 j + 1 2 T i j + 1 + T i 1 j + 1 ) + ( T i + 1 j 2 T i j + T i 1 j ) )  
r = D Δ t 2 Δ x 2   and   b = D δ Δ t 2 Δ x 2 ( 1 + 2 r ) θ i j + 1 r θ i + 1 j + 1 r θ i 1 j + 1 b T i + 1 j + 1 + 2 b T i j + 1 b T i 1 j + 1 = ( 1 2 r ) θ i j + r θ i + 1 j + r θ i 1 j + b T i + 1 j 2 b T i j + b T i 1 j  
The discretization of the boundary conditions is given by relations (19)–(22).
For mass transfer, we have:
( x = 0 ) :   ( T i + 1 j T i j ) Δ x ( θ i + 1 j θ i j ) Δ x h m 1 ρ 0 D ( ρ 1 ρ 1 )  
( x = e ) :   ( T i j T i 1 j ) Δ x ( θ i j θ i 1 j ) Δ x h m 2 ρ 0 D ( ρ 2 ρ 2 )  
For heat transfer:
( x = 0 ) :   ( λ + ρ 0 D ) ( T i + 1 j T i j ) Δ x ρ O L v D ( θ i + 1 j θ i j ) Δ x = h 1 ( T f 1 T ( 0 ) )  
( x = e ) :   ( λ + ρ 0 D ) ( T i j T i 1 j ) Δ x ρ O L v D ( θ i j θ i 1 j ) Δ x = h 2 ( T ( e ) T f 2 )  
The numerical resolution of the coupled system with the initial condition and the boundary conditions passes through a discretization according to the implicit scheme of Crank–Nicolson [18] leading to two algebraic systems, one having an unknown temperature and the other having the water content.

5. Results and Discussions

The results presented in this work relate to the study of coupled heat and moisture transfers that occur within four wall types (E0, E1, E2, and E3) of 3-cm thickness. In the initial state, the walls have a constant temperature of T 0 = 20   ° C and an initial water content of   θ 0 = 0.2   k g / k g [4]. The mass diffusivity coefficients are derived from Tamene et al. [13] as well as the values of the boundary conditions, which are: h 1 = 50   W / m 2 · K , h 2 = 100   W / m 2 · K   T f 1 = 15   ° C , θ 1 = 0.5   k g / k g , and θ 2 = 0.75   k g / k g .
Figure 2 and Figure 3 represent the evolution of the temperature and the water content respectively as a function of time at the position   x = 1.2   c m x = 1.2   cm . The shape of these curves corresponds to those obtained by Hens, Remache et al. and Chikhi [7,19,20]. Figure 2 shows that in the time interval ( 0 < t < 120   min ), there is a rapid rise in the average temperature of the wall, which causes evaporation.
This happens only on the surface, and it results in a linear decrease of the average water content (see Figure 3). During this period, the mass transfer can generally be assimilated to the evaporation at the free surface of a liquid [8]. This continues until the capillary forces that bring the moisture in liquid form from the inside of the wall toward the outer surface become rather weak, which indicates that the liquid phase is discontinuous and no longer flows [8].
As a result, the transfer of moisture in the liquid phase to the surface stops. However, an evaporation front appears and propagates toward the inside of the wall. Beyond 120 min, we notice that the average rate of humidity drops considerably; it becomes very low, and the temperature of the wall becomes almost constant.
These curves also show the influence of the dosage of thatch fibers on the temperature and humidity profiles. We see in Figure 3 that all of the curves have the same shape. It is observed that for a given moment, the temperature decreases as the fiber dosage increases. This can be justified by the composite materials having a low thermal conductivity and therefore being considered thermally insulating materials.
Moreover, the increase in the quantity of fibers that are introduced into the earth brick modifies the profile of the water content, as shown in Figure 3. This modification of the slope can be explained by the lightness of these composite materials. The phenomenon of dispersion within the material significantly increases the opening of the pores, which favors the elimination of water. In addition, it can be seen that between 0–120min, the curves corresponding to the samples E2 and E3 are merged, and beyond this range they diverge.
Figure 4 and Figure 5 showed the spatial distributions of temperature and moisture content throughout the wall for a period of time that is equal to 60 min ( t = 60   min ) for the composites materials E0, E1, E2, and E3. It can be noticed that the temperature in the wall increases in the space through the addition of thatched fibers (Figure 4). This is due to the ambient temperature, which is higher than the wall’s temperature. It can be noticed that in Figure 5, the moisture content in the wall reduces in the space with the addition of thatched fibers. The reduction rate of the moisture content is higher in the surface region compared to the interior of the wall; moreover, at first, the moisture content reduces rapidly, and as the heating period progresses, the rate of reduction of the moisture content becomes less.

6. Conclusions

In this paper, we carried out numerical simulations to study the coupled heat and mass transfers across wall of a building envelope that is subjected to two different atmospheric conditions. The envelopes that were studied consist of either simple earth bricks or composite materials (laterite and thatch fiber). The resulting equations were discretized using the finite difference method. All of the results that were obtained make it possible to highlight the evolutions of the temperature and the water content. It is clear that the addition of thatched fibers in the laterite soil makes the material hygroscopic and more thermally insulating. The results that are obtained are in agreement with those found in the literature.

Author Contributions

Conceptualization, D.N. and P.M.; Formal analysis, D.N. and P.M.; Methodology, M.N.; Writing manuscript, M.N. and C.F.T.

Funding

This research received no external funding.

Acknowledgments

The authors would like to thank the Local Materials Promotion Authority (MIPROMALO) in Cameroon which helps in conditioning and in the mechanical characterization of the samples used for this study and the laboratory of Energy, Water and Environment (L3E), National Advanced School of Engineering which helped in their thermo-physical characterization. We are also grateful to Eric Kabe Moukete for his computing assistance.

Conflicts of Interest

The authors declare no conflict of interest.

Nomenclature

C P Specific heat ( J / k g . K )
D Moisture diffusivity ( m 2 / s )
h Heat convection transfer coefficient ( W / m 2 · K )
h m Mass convection transfer coefficient ( m / s )
eWall tchikness (m)
L V Latent heat of vaporisation (J / k g )
PPressure (Pa)
TTemperature (°C)
tTime (s)
Greek symbols
λ Thermal conductivity ( W / m · K )
ε Phase change rate
ρ 0 Mass density ( k g / m 3 )
δ Global thermomigration coefficient
θ Moisture content (kg/kg)
Subscripts
LLiquid
VVapour
0Initial
1Internal side
2External side
Far wall

References

  1. Beguin, J.B.; Kalt, M.; Leroy, J.L.; Louis, D.; Makary, J.; Pelloux, P.; Peronne, H.N. L’habitat au Cameroun; Paris-VIIe, Editions de l’Union Française; Publication de l’office de la recherche scientifique Outre-Mer: Paris, France, 1952. [Google Scholar]
  2. Meukam, P.; Noumowe, A.; Kofane, T.C. Thermo Physical Properties of Lateritic Soil Bricks: Influence of Water Content; International Atomic Energy Agency (IAEA): Vienna, Austria, 2002; Volume 34, p. 22, IC/2002/157; Available online: https://inis.iaea.org/collection/NCLCollectionStore/_Public/34/035/34035601.pdf (accessed on 10 August 2018).
  3. Petkova-Slipets, R.; Zlateva, P. A thermal insulating properties of straw filled environmentally friendly building materials. Civ. Environ. Eng. 2017, 13, 52–57. [Google Scholar] [CrossRef]
  4. Janssen, H.; Blocken, B.; Carmeliet, J. Conservative modelling of the moisture and heat transfer in building components under atmospheric excitation. Int. J. Heat Mass Transf. 2007, 50, 1128–1140. [Google Scholar] [CrossRef] [Green Version]
  5. Qin, M.; Belarbi, R.; Aït-Mokhtar, A. Transfer function method to calculate simultaneous heat and moisture transfer in porous building materials. In Proceedings of the Annex 41 MOIST-ENG, Working Meeting, Kyoto, Japan, 3–5 April 2006. [Google Scholar]
  6. Djongyang, N.; Tchinda, R.; Njomo, D. A study of coupled heat and mass transfer across a porous building component in intertropical conditions. Energy Build. 2009, 41, 461–469. [Google Scholar] [CrossRef]
  7. Hens, H.L.S.C. Combined heat, air, moisture modelling: A look back, how, of help? Build. Environ. 2015, 91, 138–151. [Google Scholar] [CrossRef]
  8. Sotehi, N.; Chaker, A. Numerical analysis of simultaneous heat and mass transfer in cork lightweight concretes used in building envelopes. Phys. Procedia 2014, 55, 429–436. [Google Scholar] [CrossRef]
  9. Chang, W.J.; Weng, C.-I. An analytical solution to coupled heat and moisture diffusion transfer in porous materials. Int. J. Heat Mass Transf. 2000, 43, 3621–3632. [Google Scholar] [CrossRef]
  10. Liua, F.; Jia, B.; Chena, B.; Geng, W. Moisture transfer in building envelope and influence on heat transfer. Procedia Eng. 2017, 205, 3654–3661. [Google Scholar] [CrossRef]
  11. Meukam, P. Modeling of Heat and Mass Transfer in Lateritic Building Envelopes; IC/2002/157; International Atomic Energy Agency (IAEA): Vienna, Austria, 2004; Volume 34, p. 22, IC/2004/111; Available online: http://www.ictp.it/~pub_off (accessed on 10 August 2018).
  12. Philip, J.R.; De Vries, D.A. Moisture movement in porous media under temperature gradients. Trans. Am. Geophys. Union 1957, 38, 222–232. [Google Scholar] [CrossRef]
  13. Tamene, Y.; Abboudi, S.; Bougriou, C. Study of heat and moisture diffusion through a wall exposed to solar heat flux. J. Eng. Sci. Technol. 2011, 6, 429–444. [Google Scholar]
  14. Nitcheu, M.; Meukam, P.; Damfeu, J.C.; Njomo, D. Thermomechanical characterization of compressed clay bricks reinforced by thatch fibres for the optimal use in building. Mater. Sci. Appl. 2018. submitted. [Google Scholar]
  15. Luikov, A.V. Heat and Mass Transfer in Capillary-Porous Bodies; Chap 6; Pergamon Press: Oxford, UK, 1966; pp. 1–531. [Google Scholar]
  16. Belarbi, N.; Saighi, M. Etude Comparative des Méthodes D’évaluation du Taux D’évaporation à Partir d’une Surface D’eau Libre: Application Aux Régions Arides et semi Arides en Algérie, 13èmes Journées Internationales de Thermique; ENStimac: Albi, France, 2007. [Google Scholar]
  17. World Meteorological Organization. Guide to Meteorological Instruments and Methods of Observation, annex4-B? Formulae for the Computation of Measures of Humidity; World Meteorological Organization: Geneva, Switzerland, 2008. [Google Scholar]
  18. Gerald, C.F.; Wheatley, P.O. Applied Numerical Analysis, 7th ed.; Addison Wesley Publishing Company: Boston, MA, USA, 1978. [Google Scholar]
  19. Remache, L.; Belhamri, A. Modélisation du séchage par convection. Revue des Energies Renouvelables CISM’08 Oum El Bouaghi. Available online: https://www.cder.dz/download/CISM08_26.pdf (accessed on 10 August 2018).
  20. Chikhi, A. Etude du Comportement Thermo-Hydrique des Parois des Bâtiments. Influence des Effets de L’état Hygrothermique et des Propriétés Thermo-Physiques. Ph.D. Thesis, Université Constantine, Constantine, Algeria, 2006; pp. 1–157. [Google Scholar]
Figure 1. Physical model.
Figure 1. Physical model.
Fibers 06 00075 g001
Figure 2. Influence of thatched fibers percentage on the temperature profile at x   = 1.2   cm .
Figure 2. Influence of thatched fibers percentage on the temperature profile at x   = 1.2   cm .
Fibers 06 00075 g002
Figure 3. Influence of the thatched fibers percentage on the water content profile at x   = 1.2   cm .
Figure 3. Influence of the thatched fibers percentage on the water content profile at x   = 1.2   cm .
Fibers 06 00075 g003
Figure 4. Influence of the thatched fibers percentage on the temperature profile through the composite material at t =   60   min .
Figure 4. Influence of the thatched fibers percentage on the temperature profile through the composite material at t =   60   min .
Fibers 06 00075 g004
Figure 5. Influence of the thatched fibers percentage on the water content profile through the composite material at t = 60   min .
Figure 5. Influence of the thatched fibers percentage on the water content profile through the composite material at t = 60   min .
Fibers 06 00075 g005
Table 1. Thermophysical properties of materials [14].
Table 1. Thermophysical properties of materials [14].
Designation.   ρ   ( k g / m 3 )   λ   ( J / m · K ) λ   ( W / mK )     C P   ( J / k g · K )  
E01775.860.710870.46
E11770.610.642869.57
E21751.910.549867.18
E31745.950.511861.73

Share and Cite

MDPI and ACS Style

Nitcheu, M.; Njomo, D.; Meukam, P.; Talla, C.F. Modeling of Coupled Heat and Mass Transfers in a Stabilized Earthen Building Envelope with Thatched Fibers. Fibers 2018, 6, 75. https://doi.org/10.3390/fib6040075

AMA Style

Nitcheu M, Njomo D, Meukam P, Talla CF. Modeling of Coupled Heat and Mass Transfers in a Stabilized Earthen Building Envelope with Thatched Fibers. Fibers. 2018; 6(4):75. https://doi.org/10.3390/fib6040075

Chicago/Turabian Style

Nitcheu, Madeleine, Donatien Njomo, Pierre Meukam, and Cyrille Fotsing Talla. 2018. "Modeling of Coupled Heat and Mass Transfers in a Stabilized Earthen Building Envelope with Thatched Fibers" Fibers 6, no. 4: 75. https://doi.org/10.3390/fib6040075

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop