Next Article in Journal
Optimal Sensor Placement in Hydraulic Conduit Networks: A State-Space Approach
Next Article in Special Issue
Effects of Orifice Sizes for Uncontrolled Filling Processes in Water Pipelines
Previous Article in Journal
Assessment of Water Measurements in an Irrigation Canal System Based on Experimental Data and the CFD Model
Previous Article in Special Issue
Analysis of Sub-Atmospheric Pressures during Emptying of an Irregular Pipeline without an Air Valve Using a 2D CFD Model
 
 
Article

2D CFD Modeling of Rapid Water Filling with Air Valves Using OpenFOAM

1
Facultad de Ingeniería, Universidad Tecnológica de Bolívar, Cartagena 131001, Colombia
2
Canal de Experiencias de Arquitectura Naval CEAN, Faculty of Engineering, Universidad de Buenos Aires, Buenos Aires C1063ACV, Argentina
3
Grupo INMEDIT S.A.S., Facultad de Ingeniería, Universidad de Cartagena, Cartagena 130001, Colombia
4
Departamento de Ingeniería Hidráulica y Medio Ambiente, Universitat Politècnica de València, 46022 Valencia, Spain
*
Author to whom correspondence should be addressed.
Academic Editor: Mauro De Marchis
Water 2021, 13(21), 3104; https://doi.org/10.3390/w13213104
Received: 1 October 2021 / Revised: 25 October 2021 / Accepted: 31 October 2021 / Published: 4 November 2021
(This article belongs to the Special Issue Hydraulic Transients in Water Distribution Systems)
The rapid filling process in pressurized pipelines has been extensively studied using mathematical models. On the other hand, the application of computational fluid dynamics models has emerged during the last decade, which considers the development of CFD models that simulate the filling of pipes with entrapped air, and without air expulsion. Currently, studies of CFD models representing rapid filling in pipes with entrapped air and with air expulsion are scarce in the literature. In this paper, a two-dimensional model is developed using OpenFOAM software to evaluate the hydraulic performance of the rapid filling process in a hydraulic installation with an air valve, considering different air pocket sizes and pressure impulsion by means of a hydro-pneumatic tank. The two-dimensional CFD model captures the pressure evolution in the air pocket very well with respect to experimental and mathematical model results, and produces improved results with respect to existing mathematical models. View Full-Text
Keywords: computational fluid dynamics; pipeline filling; transient flow; OpenFOAM; air valve computational fluid dynamics; pipeline filling; transient flow; OpenFOAM; air valve
Show Figures

Figure 1

MDPI and ACS Style

Aguirre-Mendoza, A.M.; Oyuela, S.; Espinoza-Román, H.G.; Coronado-Hernández, O.E.; Fuertes-Miquel, V.S.; Paternina-Verona, D.A. 2D CFD Modeling of Rapid Water Filling with Air Valves Using OpenFOAM. Water 2021, 13, 3104. https://doi.org/10.3390/w13213104

AMA Style

Aguirre-Mendoza AM, Oyuela S, Espinoza-Román HG, Coronado-Hernández OE, Fuertes-Miquel VS, Paternina-Verona DA. 2D CFD Modeling of Rapid Water Filling with Air Valves Using OpenFOAM. Water. 2021; 13(21):3104. https://doi.org/10.3390/w13213104

Chicago/Turabian Style

Aguirre-Mendoza, Andres M., Sebastián Oyuela, Héctor G. Espinoza-Román, Oscar E. Coronado-Hernández, Vicente S. Fuertes-Miquel, and Duban A. Paternina-Verona. 2021. "2D CFD Modeling of Rapid Water Filling with Air Valves Using OpenFOAM" Water 13, no. 21: 3104. https://doi.org/10.3390/w13213104

Find Other Styles
Note that from the first issue of 2016, MDPI journals use article numbers instead of page numbers. See further details here.

Article Access Map by Country/Region

1
Back to TopTop