1. Introduction
Carbon dioxide is a gas with fierce greenhouse effect. Since the beginning of industrial revolution, more and more carbon dioxide has been released into the atmosphere owing to overexploitation of fossil fuels. Relevant data show that the increasing amount of carbon dioxide in the atmosphere results in global temperature rises by 55% [
1,
2,
3,
4]. Carbon dioxide emitted into the atmosphere pollutes the environment and causes an abnormal climate. Meanwhile, carbon dioxide also plays a vital role in the chemical destruction of the ozone layer. Therefore, it seems more urgent to deal with the removal of carbon dioxide. Currently, a variety of methods have been studied to remove carbon dioxide, including chemical adsorption [
5], physical adsorption [
5], chemical conversion [
6], cryogenic separation [
7], membrane separation, and so on [
8]. Adsorption methods, because of their mild operating conditions, low energy consumption, fast adsorption rate, strong regeneration performance, and stable performance, are already favorable and have been paid more and more attention by researchers at home and abroad. Scholars such as Malek Alaie and Delgado et al. [
9,
10] showed application of metalorganic frameworks (MOFs), alumina, and zeolite in the removal of carbon dioxide.
Zeolite with open-framework aluminosilicate structures was [
11], and remains, a kind of adsorption material with excellent performance. Compared with other adsorbents, zeolite not only has large specific surface and microporous structure but also has many holes with the same size which can accommodate adsorbed molecules in crystal lattice [
6]. In addition, the internal surface of the zeolite is highly polarized and has a strong electrostatic field [
6,
12]. Meanwhile, carbon dioxide with high polarity quadrupole can react with cations in zeolite [
13,
14]. Currently, Garshasbi V. et al. [
8] reported the carbon dioxide adsorption equilibrium on zeolite 13X prepared from natural clays. Gholipour F. et al. [
4] studied the adsorption equilibrium of methane and carbon dioxide using zeolite 13X as the adsorbent material. Therefore, zeolite, a nanoporous inorganic material, has broad application prospects in the field of carbon dioxide removal. However, most of the zeolite used in life is synthesized from chemical raw materials. In this study, zeolite 4A is synthesized by a simple hydrothermal method using low-grade kaolin as a raw material and the adsorption equilibrium of carbon dioxide on zeolite 4A is studied. The synthesis of zeolite 4A by using low-grade kaolin as a raw material reduces the synthesis cost of the zeolite and protects the environment. In addition, the study makes full use of waste resources.
In this study, it is reported that zeolite 4A is synthesized by hydrothermal synthesis using low -grade kaolin as a raw material. The properties of the synthesized zeolite 4A were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR),
29Si magic-angle spinning (MAS)-nuclear magnetic resonance (NMR) and
27Al MAS-NMR, X-ray fluorescence (XRF), scanning electron microscopy (SEM)-energy-dispersive spectrometry (EDS), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET), and thermogravimetry (TG)-differential thermal analysis (DTA). Meanwhile, using the static capacity method [
12], the adsorption equilibrium isotherm of carbon dioxide on zeolite 4A was studied by adsorption experiment system. In addition, the adsorption equilibrium data of carbon dioxide were used to fit the Langmuir isotherm model and the Freundlich isotherm model, respectively.
3. Results and Discussion
Raw kaolin, a clay composed mainly of kaolinite, contains large amounts of silicon and aluminum sources. However, the silicon and aluminum sources in kaolin are in an inactive state, which makes it difficult to directly react to the synthesis of zeolite 4A. A crucial step is activation treatment of raw kaolin to obtain a more reactive phase, metakaolin [
15].
Figure 1 illustrates the thermal analysis curve of raw kaolin. According to the TG curve, the kaolin shows two mass-reduction processes. The first mass-reduction process is attributed to the loss of adsorbed water molecules in the temperature range of 10–400 °C. The second mass-reduction process is in the temperature range of 400–600 °C, which is ascribed to the reorganization of octahedral and tetrahedral layers of the raw kaolin, resulting in the dehydroxylation of the structural OH [
15,
16,
17]. At the same time, an endothermic peak appears in the DTA curve at around 490 °C. The thermal stability analysis of the raw kaolin shows that the transition temperature of kaolin to metakaolin is around 490 °C. The chemical compositions of the raw kaolin, metakaolin, synthesized zeolite 4A, and commercial zeolite 4A could be derived from
Table 1. It can be concluded from
Table 1 that the major chemical compositions of raw kaolin are SiO
2, Al
2O
3, and a small amount of Fe
2O
3. Meanwhile, it is found that the weight percentages of SiO
2, Al
2O
3, and Fe
2O
3 in raw kaolin are 55.466, 39.240, and 1.415, respectively. The silicon–aluminum molar ratio in the raw kaolin was increased from 2.4 to 2.5 by calcination treatment at 700 °C for 4 h, and a small amount of Fe
2O
3 was removed. Due to the low content of Fe
2O
3, it had little effect on the synthetic zeolite and did not require iron removal treatment. The silicon–aluminum molar ratio of 2.5 is in accordance with the requirement of the silicon and aluminum components of zeolite 4A synthesis.
Figure 2A shows the phase analysis of the raw kaolin, metakaolin, synthesized zeolite 4A, and commercial zeolite 4A. It could be observed from
Figure 2Aa that the raw kaolin mainly contains kaolinite and a small amount of illite and quartz. However, according to the Joint Committee on Powder Diffraction Standards (JCPDS) [
15,
18], the feature diffraction peaks of kaolinite occur at 2θ = 12.4° and 24.8°, which is in accordance with the reference value of single-phase kaolinite. Upon calcinations at 700 °C for 4 h, the XRD pattern exhibits the expected significant characteristic, the disappearance of the diffraction peaks of kaolinite, in comparison to the pattern of raw kaolin, accompanied by the appearance of amorphous aluminosilicate, as shown in
Figure 2Ab. Meanwhile, characteristic peaks of the impurity illite and quartz are observed in the diffraction peak of metakaolin [
15].
Figure 2B shows the FTIR spectrums of raw kaolin, metakaolin, synthesized zeolite 4A, and commercial zeolite 4A. From
Figure 2Ba, it could be observed that there are a lot of unambiguous definition FTIR vibration bands in the range of 400–1400 cm
−1, due to the vibrations of Si-O, Si-O-Al, and Al-OH [
19]. The vibration bands at 1031 cm
−1, 912 cm
−1, 541 cm
−1, and 468 cm
−1 could be assigned to the stretching vibration of Si-O units, the bending vibration of Al-OH units, the bending vibration of the Si-O-Al units, and the bending vibration of Si-O units in the raw kaolin structure, respectively. These vibration bands are removed during the conversion to metakaolin, and new feature vibration bands appear at 1077 cm
−1, 796 cm
−1, 694 cm
−1 and 479 cm
−1. The loss of the vibration bands at 912 cm
−1 indicates that the Al-OH units are lost [
20]. The reason is that the hydroxyl bond is broken under high temperature calcination. Meanwhile, the feature band of metakaolin is seen at 796 cm
−1 [
21]. In addition, from
Figure 2(Ca,b), it could be observed the raw kaolin with hexagonal platy morphology and the appearance of amorphous metakaolin.
From
Figure 2(Ac,d,Bc,d), it could be observed that the XRD pattern and FTIR structure of synthesized zeolite 4A match well with commercial zeolite 4A, which confirms that zeolite 4A is successfully synthesized. For XRD pattern of synthesized zeolite 4A, according to JCPDS [
21,
22], the feature diffraction peaks of zeolite 4A occur at 2θ = 7.2°, 10.3°, 12.6°, 16.2°, 21.8°, 24.0°, 27.2°, 29.9°, and 34.2°, which is in accordance with the reference value of single-phase zeolite 4A. However, it could be seen from the diffraction pattern that illite and quartz, treated as impurities, still exist. Recent studies have reported the stability of illite and quartz during hydrothermal synthesis [
15]. The XRD patterns in
Figure 2A correspond to the FTIR spectrums in
Figure 2B. For FTIR structure of zeolite 4A, the vibration bands at 1001 cm
−1 and 471 cm
−1 could be assigned to the stretching vibration of Si-O or Al-O units and the vibration of Si-O-Al units in the zeolite 4A structure, respectively. The vibration bands appeared at 668 cm
−1 and 556 cm
−1 could be assigned to the vibration modes of the zeolite 4A framework [
22]. The SEM morphology of synthesized zeolite 4A was studied as shown in
Figure 2(Cc,d). It could be clearly seen that the zeolite 4A have a typical cubic morphology with homogeneous size distribution. SEM morphology of commercial zeolite 4A is presented in
Figure 3. The morphology of synthesized zeolite 4A matches well with the commercial zeolite 4A in terms of size and structure. The solid state
27A1 and
29Si MAS-NMR spectra of synthesized zeolite 4A are shown in
Figure 4. It could be seen from
Figure 4a that only one resonance at around 57.810 ppm was exhibited, which implies that Al species dissolved from metakaolin entered the 4-coordinate Si-O network to form the framework Si(OAl)3(OSi) in the alkaline solution [
23,
24,
25]. In addition, the full width at half maximum (FWHM) of resonance around 57.810 ppm was narrow, which illustrates that the crystallinity of the zeolite 4A is favorable [
23]. The typical
29Si MAS-NMR resonance for zeolite 4A, around −92.017 ppm, was quite sharp, indicating that zeolite 4A has favorable lattice order as shown in
Figure 4b [
24]. In addition, EDS spectrums of raw kaolin, metakaolin, synthesized zeolite 4A, and commercial zeolite 4A is presented in
Figure 5. For the raw kaolin and metakaolin, it could be clearly seen the peaks constituting the elements O, Al, and Si in the spectrum. For zeolite 4A, a new peak associated with the element Na appears in the spectrum. Combined with
Table 1, it can be revealed that positively charged sodium ions are present in the synthesized zeolite 4A as equilibrium cations.
Following that, TEM technique was applied to further study the formation of synthesized zeolite 4A as shown in
Figure 6. It could be seen from
Figure 6a,b that the zeolite 4A with good crystallinity grows solidly. The lattice fringes, as shown in
Figure 6c,d, indicate pore size of 0.4–0.5 nm. The electron diffraction pattern as shown in
Figure 6e indicates the formation of body-centered cubic crystals. As could be seen from
Figure 6f, elemental analysis spectrum shows that the main components of the zeolite 4A are Na, Al, Si, and O [
26]. The percentages of Na, Al, Si, and O are 5.2, 28.41, 29.55, and 36.93%, respectively. In addition, selected-area electron diffraction patterns obtained from the edges of the zeolite 4A are presented in
Figure 7. It could be seen from
Figure 7b that there are the spotty diffraction rings, which indicates the polycrystallinity of the zeolite 4A structure [
11]. From
Figure 8, it could be confirmed again that the elements Na, Si, Al, and O are present in the zeolite 4A structure. In addition, these mappings clearly show that the zeolite 4A contains a large amount of silica and alumina [
26]. From
Figure 8b, it could be seen that the Na, Si, Al, and O elements are uniformly distributed in zeolite 4A.
The nitrogen adsorption-desorption isotherm of the synthesized zeolite 4A and pore size distribution of the synthesized zeolite 4A are presented in
Figure 9. It could be seen from
Figure 9a that there is a hysteresis loop, indicating the existence of mesoporosity [
19]. The pore size distribution of the zeolite 4A obtained by the Barrett–Joyner–Halenda equation (BJH) is shown in
Figure 9b. From
Figure 9b, it could be concluded that the BJH adsorption average pore diameter and BJH desorption average pore diameter are 10.5063 nm and 9.0646 nm, respectively. The micropore volume, BET surface area, and micropore surface area of the synthesized zeolite 4A and commercial zeolite 4A are listed in
Table 2. From
Table 2, the micropore volume, BET surface area and micropore surface area of synthesized zeolite are significantly higher than commercial zeolite 4A.
Thermal stability of synthesized zeolite 4A during heat treatment was studied as shown in
Figure 10. From the TG curve, the two weight reductions of zeolite 4A could be observed. The first weight reduction of zeolite 4A occurred in the temperature range of 20−180 °C. At the same time, it could be seen from the DTA curve that the strongest endothermic peak was near 140 °C. The main reason was that the water molecules adsorbed on the zeolite 4A were completely removed. The second weight reduction occurred in the temperature range between 180 and 500 °C. The main reason is that extraframework water molecules were removed [
27]. However, a weak endothermic peak at about 930 °C could be seen from the DTA curve. It is known from the TG curve that it has nothing to do with weight reduction. The main reason is the collapse of the zeolite 4A structure [
19,
25]. Most importantly, we could conclude that the heat resistance of zeolite 4A is as high as 940 °C.
A comparative study of carbon dioxide adsorption on synthesized zeolite 4A and commercial zeolite 4A at 298 K is shown in
Figure 11. It could be seen from
Figure 11a that in the low pressure range, the carbon dioxide adsorption amount increases rapidly with the increase of the equilibrium pressure, and the carbon dioxide adsorption amount tends to be stable when the pressure reaches 45 bar [
28]. Meanwhile, it could be concluded that the synthesized zeolite 4A adsorbs more carbon dioxide than the commercial zeolite 4A in the pressure range of 0–45 bar. Combined with
Table 2, the reason is that synthesized zeolite 4A has a larger micropore surface area and micropore volume compared to commercial zeolite 4A [
2]. The maximum adsorption amount of carbon dioxide in the adsorption curve indicates that the zeolite 4A reaches the saturation adsorption limit at 298 K. Meanwhile, it is shown that all active sites on the zeolite 4A were sufficiently bound to the carbon dioxide gas. From
Figure 11b, it could be clearly seen that the maximum adsorption amounts of synthesized zeolite 4A and commercial zeolite 4A for carbon dioxide are 59.382 mL/g and 55.4303 mL/g, respectively. In this study, a nonlinear regression analysis was performed to determine the adsorption isotherm model of the zeolite, as shown in
Figure 11c,d. The typical type I behavior was shown according to the IUPAC adsorption isotherm classification criteria [
2], which demonstrates the monolayer adsorption mechanism of microporous adsorbents [
28,
29]. Combined with
Table 3, the Langmuir isotherm model fully complies with the isotherm curve for the adsorption of carbon dioxide by synthesized zeolite 4A and commercial zeolite 4A, which indicates the monolayer adsorption on the surface of the uniform adsorbent, and the interaction between the adsorbed particles are negligible [
30]. Meanwhile, it can be seen from
Figure 11c,d that a large number of adsorbed active sites are activated within a suitable equilibrium pressure range. In addition, the study has a guiding significance for the determination of adsorption pressure and regeneration pressure as the adsorption pressure changes during the adsorption process.