Search Results (5)

Hydrogen and some of its derivatives (such as e-methanol, e-methane, and e-ammonia) are promising energy carriers that have the potential to replace conventional fuels, thereby eliminating their harmful environmental impacts. An innovative use of hydrogen as a zero-emission fuel is forming weakly ionized plasma by seeding the combustion products of hydrogen with a small amount of an alkali metal vapor (cesium or potassium). This formed plasma can be used as a working fluid in supersonic open-cycle magnetohydrodynamic (OCMHD) power generators. In these OCMHD generators, direct-current (DC) electricity is generated straightforwardly without rotary turbogenerators. In the current study, we quantitatively and qualitatively explore the levels of electric conductivity and the resultant volumetric electric output power density in a typical OCMHD supersonic channel, where thermal equilibrium plasma is accelerated at a Mach number of two (Mach 2) while being subject to a strong applied magnetic field (applied magnetic-field flux density) of five teslas (5 T), and a temperature of 2300 K (2026.85 °C). We varied the total pressure of the pre-ionization seeded gas mixture between 1/16 atm and 16 atm. We also varied the seed level between 0.0625% and 16% (pre-ionization mole fraction). We also varied the seed type between cesium and potassium. We also varied the oxidizer type between air (oxygen–nitrogen mixture, 21–79% by mole) and pure oxygen. Our results suggest that the ideal power density can reach exceptional levels beyond 1000 MW/m³ (or 1 kW/cm³) provided that the total absolute pressure can be reduced to about 0.1 atm only and cesium is used for seeding rather than potassium. Under atmospheric air–hydrogen combustion (1 atm total absolute pressure) and 1% mole fraction of seed alkali metal vapor, the theoretical volumetric power density is 410.828 MW/m³ in the case of cesium and 104.486 MW/m³ in the case of potassium. The power density can be enhanced using any of the following techniques: (1) reducing the total pressure, (2) using cesium instead of potassium for seeding, and (3) using air instead of oxygen as an oxidizer (if the temperature is unchanged). A seed level between 1% and 4% (pre-ionization mole fraction) is recommended. Much lower or much higher seed levels may harm the OCMHD performance. The seed level that maximizes the electric power is not necessarily the same seed level that maximizes the electric conductivity, and this is due to additional thermochemical changes caused by the additive seed. For example, in the case of potassium seeding and air combustion, the electric conductivity is maximized with about 6% seed mole fraction, while the output power is maximized at a lower potassium level of about 5%. We also present a comprehensive set of computed thermochemical properties of the seeded combustion gases, such as the molecular weight and the speed of sound. Full article

The presence of abundant water vapor in industrial organic waste gases greatly reduces the selective adsorption of volatile organic pollutants (VOCs). The polarity of the adsorbent and VOC molecules plays an important role in the adsorption process, especially in the presence of water vapor. In this paper, commercial coconut shell activated carbon (CSC) was modified by a thermal reduction treatment to obtain heat-treated coconut shell activated carbon (HCSC). CSC and HCSC exhibited similar pore structure characteristics but differed significantly in surface oxygen content (10.97% and 7.55%, respectively). Dynamic adsorption breakthrough experiments were conducted to determine the dynamic adsorption capacities of toluene on both adsorbents under varying relative humidity levels. HCSC demonstrated superior toluene/water vapor adsorption selectivity. Further analyses of toluene adsorption kinetics, activation energy, and water vapor adsorption isotherms revealed that the lower surface oxygen functional group content of HCSC resulted in a weaker surface polarity, facilitating the adsorption of weakly polar toluene. This was attributed to stronger toluene–HCSC interactions and weaker water–HCSC interactions. The dynamic adsorption capacities of three VOCs with varying polarities were also tested on HCSC. The observed VOC/water vapor adsorption selectivity had the following order: toluene > n-heptane > 1,2-dichloroethane. Grand Canonical Monte Carlo (GCMC) simulations were employed to quantify the relationship between the adsorption selectivity of eight VOCs with varying polarities and their molecular polarity. The results indicated a decrease in adsorption selectivity with increasing VOC polarity. A mechanistic analysis suggests that more polar VOCs prefer to adsorb polar oxygen-containing functional groups, competing with water molecules for adsorption sites. Under high humidity, hydrogen bonding leads to the formation of water clusters, exacerbating this competition. This research holds significant implications for the efficient selective adsorption of VOCs with varying polarities in humid industrial conditions. Full article

Under axial and azimuthal magnetic inductions, the similarity solutions for a cylindrical shock wave in a weakly conducting ideal gas are determined using the Lie group invariance method. The axial and azimuthal magnetic inductions and density are presumed to vary in an ambient medium. This study determines the form of expression for axial and azimuthal magnetic inductions in the ambient medium. The ambient density is considered to be varying according to the power law of the shock radius. The weakly conducting medium causes inadequate magnetic freezing. We have numerically solved the system of ordinary differential equations that resulted from applying the Lie group invariance method to the system of partial differential equations. The impact of the variation in the ambient density exponent, the ratio of specific heats, magnetic Reynolds number, or the inverse square of axial and azimuthal Alfven Mach numbers on the shock strength and the flow variables behind the shock front is discussed. It is found that the shock strength decreases with an increase in the ratio of specific heats, magnetic Reynolds number, or the inverse square of axial and azimuthal Alfven Mach numbers. Full article

Airport emissions have received increased attention because of their impact on atmospheric chemical processes, the microphysical properties of aerosols, and human health. At present, the assessment methods for airport pollution emission mainly involve the use of the aircraft emission database established by the International Civil Aviation Organization, but the emission behavior of an engine installed on an aircraft may differ from that of an engine operated in a testbed. In this study, we describe the development of a long-path differential optical absorption spectroscopy (LP-DOAS) instrument for measuring aircraft emissions at an airport. From 15 October to 23 October 2019, a measurement campaign using the LP-DOAS instrument was conducted at Hefei Xinqiao International Airport to investigate the regional concentrations of various trace gases in the airport’s northern area and the variation characteristics of the gas concentrations during an aircraft’s taxiing and take-off phases. The measured light path of the LP-DOAS passed through the aircraft taxiway and the take-off runway concurrently. The aircraft’s take-off produced the maximum peak in NO₂ average concentrations of approximately 25 ppbV and SO₂ average concentrations of approximately 8 ppbV in measured area. Owing to the airport’s open space, the pollution concentrations decreased rapidly, the overall levels of NO₂ and SO₂ concentrations in the airport area were very low, and the maximum hourly average NO₂ and SO₂ concentrations during the observation period were better than the Class 1 ambient air quality standards in China. Additionally, we discovered that the NO₂ and SO₂ emissions from the Boeing 737–800 aircraft monitored in this experiment were weakly and positively related to the age of the aircraft. This measurement established the security, feasibility, fast and non-contact of the developed LP-DOAS instrument for monitoring airport regional concentrations as well as NO₂ and SO₂ aircraft emissions during routine airport operations without interfering with the normal operation of the airport. Full article

In the present review, complexity in multibubble sonoluminescence (MBSL) is discussed. At relatively low ultrasonic frequency, a cavitation bubble is filled mostly with water vapor at relatively high acoustic amplitude which results in OH-line emission by chemiluminescence as well as emissions from weakly ionized plasma formed inside a bubble at the end of the violent bubble collapse. At relatively high ultrasonic frequency or at relatively low acoustic amplitude at relatively low ultrasonic frequency, a cavitation bubble is mostly filled with noncondensable gases such as air or argon at the end of the bubble collapse, which results in relatively high bubble temperature and light emissions from plasma formed inside a bubble. Ionization potential lowering for atoms and molecules occurs due to the extremely high density inside a bubble at the end of the violent bubble collapse, which is one of the main reasons for the plasma formation inside a bubble in addition to the high bubble temperature due to quasi-adiabatic compression of a bubble, where “quasi” means that appreciable thermal conduction takes place between the heated interior of a bubble and the surrounding liquid. Due to bubble–bubble interaction, liquid droplets enter bubbles at the bubble collapse, which results in sodium-line emission. Full article