Search Results (6)

The manuscript presents the results of butt joining of 3-millimeter-thick AlCu4Mg1 alloy sheets using the FSW (friction stir welding) and UWFSW (underwater friction stir welding) methods. The aim of the research is to verify the influence of the water environment on the FSW friction welding process. The article checked three sets of joint parameters. The parameters differed in tool rotation speed and feed rate. The same sets of parameters were used for the FSW and UWFSW fusion techniques. With the supplied devices, metallographic sections are cross-sectioned, and the power supplies are subjected to a light microscope. Microhardness tests and the influence of the heat-affected zone were carried out. A monotonic test was performed. A monotonic test is available, extended with a visual correlation test. The obtained cracked fracture surfaces were examined using a scanning microscope. An analysis of the microfractographic cracking process was carried out. The obtained results did not show any improvement in the strength properties of the obtained joints made using the UWFSW technique when using a scanning microscope. Full article

The use of the friction stir welding (FSW) process as a relatively new solid-state welding technology in the aerospace industry has pushed forward several developments in different related aspects of this strategic industry. In terms of the FSW process itself, due to the geometric limitations involved in the conventional FSW process, many variants have been required over time to suit the different types of geometries and structures, which has resulted in the development of numerous variants such as refill friction stir spot welding (RFSSW), stationary shoulder friction stir welding (SSFSW), and bobbin tool friction stir welding (BTFSW). In terms of FSW machines, significant development has occurred in the new design and adaptation of the existing machining equipment through the use of their structures or the new and specially designed FSW heads. In terms of the most used materials in the aerospace industry, there has been development of new high strength-to-weight ratios such as the 3rd generation aluminum–lithium alloys that have become successfully weldable by FSW with fewer welding defects and a significant improvement in the weld quality and geometric accuracy. The purpose of this article is to summarize the state of knowledge regarding the application of the FSW process to join materials used in the aerospace industry and to identify gaps in the state of the art. This work describes the fundamental techniques and tools necessary to make soundly welded joints. Typical applications of FSW processes are surveyed, including friction stir spot welding, RFSSW, SSFSW, BTFSW, and underwater FSW. Conclusions and suggestions for future development are proposed. Full article

Friction stir welding (FSW) is an effective solid-state joining process that has the potential to overcome common problems correlated with conventional fusion welding processes. FSW is used for the joining of metallic materials, in particular Al alloys (non-heat-treatable and heat-treatable). The heat produced by the friction between the rotating tool and the workpiece material generates a softened region near the FSW tool. Although the heat input plays a crucial role in producing a defect-free weld metal, it is a serious concern in the FSW of work-hardened non-heat-treatable Al alloys. In this group of alloys, the mechanical properties, including hardness, tensile properties, and fatigue life, are adversely affected by the softening effect because of grain growth and reduced dislocation density. Considering this challenge, work-hardened Al alloys have been limited in their industrial use, which includes aerospace, shipbuilding, automotive, and railway industries. The current comprehensive review presents the various approaches of available studies for improving the quality of FSW joints and expanding their use. First, the optimization of welding parameters, including the tool rotational and traverse speeds, tool design, plunge depth, and the tilt angle is discussed. Second, the incorporation of reinforcement particles and then underwater FSW are stated as other effective strategies to strengthen the joint. Finally, some supplementary techniques containing surface modification, bobbin tool FSW, copper backing, and double-sided FSW in relation to strain-hardened Al alloys are considered. Full article

This article aims to study water-cooling effects on residual stress friction stir welding (FSW) of AA6068-T6 aluminum alloy. For this reason, the FSW and submerged FSW processes are simulated by computational fluid dynamic (CFD) method to study heat generation. The increment hole drilling technique was used to measure the residual stress of welded samples. The simulation results show that materials softening during the FSW process are more than submerged. This phenomenon caused the residual stress of the joint line in the submerged case to be lower than in the regular FSW joint. On the other hand, the results revealed that the maximum residual stresses in both cases are below the yielding strength of the AA6068-T6 aluminum alloy. The results indicated that the residual stress along the longitudinal direction of the joint line is much larger than the transverse direction in both samples. Full article

The possibility of underwater dissimilar friction stir welding of AA6061 and AA7075 aluminum alloy was explored to overcome the problem of hardness loss in different microstructural zones. Optical microscopy and electron backscattered diffraction were employed to characterize the microstructure of the joint. Vickers hardness measurements were conducted on the cross-section of the joint to evaluate the mechanical strengths. The results showed that the microstructure of the AA7075 side had undergone the same mechanisms as those occurring during conventional friction stir welding. In the case of the AA6061 side, in addition to typical restoration mechanisms, the grain subdivision was observed. The AA7075 side had finer grains compared to the AA6061 side, which may be related to the different morphology and size of precipitates. Moreover, friction stir welding caused a reduction in the hardness values in all the microstructural areas compared to those of corresponding base materials. For example, it caused a reduction in the hardness of a thermomechanically affected zone from 105 HV to 93 HV in the AA6061 side, and from 187 HV to 172 HV in the AA7075 side. The underwater media improved the overall hardness values in thermo-mechanically affected zones (13% reduction in hardness) compared to those reported in literature (57% reduction in hardness). Full article

This article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction stir welding (FSW) method. Simulation results from surface heat diffusion indicate a smaller preheated area in front of the FSW tool declined the total generated heat in the UFSWed case compared to the FSWed sample. The simulation results revealed that the strain rate of steel in the stir zone (SZ) of the FSWed joint is higher than in the UFSWed case. The microstructure of the welded sample shows that SZ’s microstructure at the UFSWed case is more refined than the FSWed case due to the higher cooling rate of the water environment. Due to obtained results, the maximum temperatures of FSWed and UFSWed cases were 1228 °C and 1008 °C. Meanwhile, the simulation results show 1200 °C and 970 °C for conventional and underwater FSW samples, respectively. The maximum material velocity in SZ predicted 0.40 m/s and 0.32 m/s for FSW and underwater FSWed samples. The better condition in the UFSW case caused the ultimate tensile strength of welded sample to increase ~20% compared to the FSW joint. Full article