Search Results (3)

The nominal maximum aggregate size (NMAS) plays a critical role in determining the mechanical performance of cement-stabilized macadam (CSM), yet its meso-mechanical influence mechanism remains insufficiently understood. In this study, three skeleton-dense CSM mixtures with different NMAS values were designed, and a combined experimental–numerical approach was adopted to investigate the macro- and meso-scale mechanical behavior. Uniaxial compression tests and aggregate crushing value tests were conducted to evaluate strength development and load-transfer characteristics, while a three-dimensional discrete element method (DEM) model incorporating realistic aggregate morphology was established to analyze the evolution of contact forces and crack propagation. The results show that increasing NMAS significantly improves the mechanical performance of CSM. Compared with CSM-30, the 7-day compressive strength of CSM-40 and CSM-50 increased by approximately 10.3% and 37.3%, respectively. The stress–strain response indicates that mixtures with larger NMAS exhibit higher stiffness and a higher strain. At the meso-scale, a larger NMAS promotes the formation of a more efficient force-chain network dominated by coarse aggregates. Strong contacts were predominantly carried by aggregates larger than 9.5 mm, and in CSM-50, the proportion of strong contacts in the 37.5–53 mm fraction exceeded 90%, indicating that the largest particles likely form the primary load-bearing skeleton. In addition, increasing NMAS delayed crack initiation, reduced crack propagation rate, and decreased the total number of cracks at failure. These findings demonstrate that macroscopic strength improvement is closely associated with meso-scale optimization of the aggregate skeleton and enhanced load-transfer efficiency. This study provides a mechanistic basis for NMAS selection and gradation optimization in semi-rigid base materials. Full article

The skeleton structure composed of mineral aggregates is the main body to bear and transfer external loading in asphalt mixtures. To investigate the loading transfer mechanism of the mineral aggregate skeleton, the uniaxial penetration test and Discrete Element Method (DEM) were conducted for the Mineral Aggregate Mixture (MAM) to analyze its mechanical behavior. The three-dimensional strong force chain (SFC) was identified and evaluated based on the proposed recognition criterion and evaluation indices. The results indicate that 4.75 mm should be the boundary to distinguish the coarse and fine aggregates. The skeleton composed of aggregates located on SFCs has better bearing and transferring loading capacity due to its SFC number, average length, and total length decreasing with an increase in the aggregate size. Compared to SMA-16 and OGFC-16, AC-16 exhibits a higher number and total length of its SFC, a smaller average length of its SFC, and a lower average strength of its SFC. Consequently, AC-16 has a lower bearing and transferring loading capacity than that of SMA-16 and OGFC-16. In addition, approximately 90% of SFCs can only transfer external loading downward through 3–5 aggregates. The average direction angle of the SFC formed by fine aggregates is significantly higher than those formed by coarse aggregates. This indicates that the load transfer range of MAM composed of fine aggregates is noticeably larger, leading to lower loading transfer efficiency. Full article

In this work, two series of chemically reactive polymers, silane coupling agents (SCAs) and water-soluble polymers, were specifically designed as an additive to improve the ductility of slag geopolymer paste by vibration pressure technique. The influences of organic polymers on the fluidity, rheological behavior, mechanical property, porosity, and toughening mechanism of slag geopolymer were investigated. The polycondensation and bonding characteristics of organic–inorganic products were calculated by ¹H liquid nuclear magnetic resonance (NMR) technology and Fourier transform infrared (FT-IR). The polymerization degree of composite geopolymer was evaluated by ²⁹Si NMR and X-ray photoelectron spectroscopy (XPS). The microscopic morphology of the geopolymer matrix was analyzed using scanning electron microscopy (SEM). The results showed that the dosage of the KH570 and PAA-Na with 5 wt% behaved best in improving the flexural strength and the compressive strength of geopolymer in their corresponding organic series, respectively. The addition of polymers decreased the fluidity and the fluidity loss ratio of geopolymer slurry but reduced the harmful pores of hardened geopolymer. The organic polymers acting as bridge-fixed water molecules weakened the repulsion force, and formed a three-dimensional network through molecular interweaving in a geopolymer matrix. Methacryloxy in silane coupling agents and carboxyl group in water-soluble polymers may contribute to the improvement of hydration product structure through strong bonding with C-A-S-H. Microscopic measurements indicated that the addition of KH570 and PAA-Na in geopolymer could form 73.55% and 72.48% Si-O-Si with C-A-S-H gel, higher than the reference, and increase the polycondensation degree of C-A-S-H phase, reflected by the increased generation of Q² and Q²(1Al) and the longer chain length, leading to a higher densified geopolymer matrix with high ductility. Full article