Search Results (5)

Extensive practice has demonstrated that the continuous pursuit of high yields in the black soil region of Northeast China resulted in imbalances in soil nutrients and declines in both soil quality and water use efficiency. Alternate wetting and drying (AWD) irrigation offers a promising solution for increasing rice yield and maintaining soil fertility. However, the success of this irrigation method largely depends on its scheduling. This study examined the threshold effects of AWD on rice growth, yield, and soil nutrient availability in the Sanjiang Plain, a representative black soil region in Northeast China. A two-year trial was conducted from 2023 to 2024 at the Qixing National Agricultural Science and Technology Park. “Longjing 31”, a local cultivar, was selected as the experimental material. The lower limit of soil water content under AWD was set as the experimental factor, with three levels: −10 kPa (LA), −20 kPa (MA), and −30 kPa (SA). The local traditional irrigation practice, continuous flooding, served as the control treatment (CK). Indicators of rice growth and soil nutrient content were measured and analyzed at five growth stages: tillering, jointing, heading, milk ripening, and yellow ripening. The results showed that, compared to CK, AWD had minimal impact on rice plant height and tiller number, with no significant differences (p > 0.05). However, AWD affected leaf area index (LAI), shoot dry matter (SDM), yield, and soil nutrient availability. In 2023, control had little effect on rice plant height and tiller number among the different irrigation treatments. The LAI of LA was 11.1% and 22.5% higher than that of MA and SA, respectively, while SDM in LA was 10.5% and 17.2% higher than in MA and SA. Significant differences were found between LA and MA, as well as between LA and SA, whereas no significant differences were observed between MA and SA. The light treatment is beneficial to the growth and development of rice, while the harsh growth environment caused by the moderate and severe treatments is unfavorable to rice growth. The average contents of nitrate nitrogen (NO₃⁻-N), available phosphorus (AP), and available potassium (AK) in LA were 11.4%, 8.4%, and 9.3% higher than in MA, and 16.7%, 11.5%, and 15.0% higher than in SA, respectively. Significant differences were observed between LA and SA. This is because the light treatment facilitates the release of available nutrients in the soil, while the moderate and severe treatments hinder this process. Although panicle number per unit area and grain number per panicle in LA were 7.5% and 2.3% higher than in MA, and 10.8% and 2.2% higher than in SA, these differences were not statistically significant. Seed setting rate and thousand-grain weight showed little variation across irrigation treatments. The yield of LA was 10,233.3 kg hm⁻², 9.1% and 14.1% higher than that of MA and SA, respectively, with significant differences observed. Compared with the moderate and severe treatments, the light treatment increases indicators such as the number of panicles per unit area, grains per panicle, thousand-grain weight, and seed setting rate, resulting in significant differences among the treatments. Water use efficiency (WUE) decreased as the control level increased. The WUE of all AWD irrigation treatments was significantly higher than that of the control treatment (CK). Compared with CK, AWD reduces evaporation, percolation, and other water losses, leading to a significant decrease in water consumption. Meanwhile, the yield remains basically unchanged or even slightly increases, thus resulting in a higher WUE than CK. The trends in rice growth, soil nutrient indicators, and WUE in 2024 were generally consistent with those observed in 2023. In 2024, the yield of LA was 9832.7 kg hm⁻², 14.9% and 17.3% higher than that of MA and SA, respectively, with significant differences observed. Based on the results, the following conclusions are drawn: (1) AWD irrigation can affect the growth of rice, alter the status of available nutrients in the soil, and thereby cause changes in yield and WUE; (2) LA is the optimal treatment for increasing rice yield, improving the availability of soil available nutrients, and improving WUE; (3) Both MA and SA enhanced WUE; however, these practices negatively impacted rice growth and the concentration of soil available nutrients, leading to a concurrent decline in yield. To increase rice yield and maintain soil fertility, LA, with an irrigation upper limit of 30 mm and a soil water potential threshold of −10 kPa, is recommended for the Sanjiang Plain region. Full article

This work proposes nanocomposites with carbon nanotubes characterized by self-sensing and self-heating properties. Recently, a growing interest in these two properties has been found in many industrial sectors, especially in the aerospace and automotive fields. While the self-sensing function allows diagnosing the presence of micro-damage in the material thanks to the detection of residual resistance, the self-heating function is exploited to properly tune the heating performance in terms of the heating rate and final temperature values. An electrical percolation value of around 0.5% by weight of carbon nanotubes was found by electrical characterization. The AC conductivity of the nanocomposites, in the range of 100 Hz to 1 MHz, evidences that beyond a CNTs amount of 0.5% wt/wt, they are characterized by a purely resistive behavior. The self-sensing analysis displayed a gauge factor value of 4.1. The solid thermal stability up to 300 °C makes the material suitable as a heating element at high temperatures. SEM investigations and temperature maps evidence a good dispersion of the conductive filler in the epoxy matrix and, consequently, good isotropy in heat distribution. As regards the trend of electrical resistance by varying the temperature, the electro-thermal investigation has shown the presence of both Positive Temperature Coefficient (PTC) and Negative Temperature Coefficient (NTC) behaviors with a predominance of NTC as soon as the temperature becomes closer to the glass transition temperature of the epoxy resin. Full article

Coal is a complex, porous medium with pore structures of various sizes. Therefore, it is difficult to accurately describe the characteristics of pore structure by using the traditional geometry method. The results from the present investigation suggest that the porous media system of the coal reservoir has obvious fractal characteristics at different scales. To study the complexity of the pores in the coal reservoir, 27 coal samples from Guizhou, SW China were studied. The fractal dimensions of coal pores were calculated, and the fractal dimension of a pore in a coal reservoir can be classified into two types: percolation and diffusion. The comprehensive fractal dimension can be obtained using the weighted summation method and the pore volume fraction of different fractal segments as the weight. The percolation fractal dimensions (D_p) of coal samples are between 2.88 and 3.12, the diffusion fractal dimensions (D_d) are between 3.57 and 3.84, and the comprehensive fractal dimensions (D_t) are between 3.05 and 3.63. The D_d values of all coal samples are all larger than the D_p values, which indicates that the random distribution and complexity of diffusion pores in coal are stronger than those of the percolation pores. The percolation fractal dimension decreases as the maturity degree increases, whereas the diffusion and comprehensive fractal dimensions increase. The diffusion pore volume fraction and total pore volume are all highly correlated with the comprehensive and diffusion fractal dimensions, respectively. The correlation between the comprehensive fractal dimension, diffusion pore volume fraction, and coal reservoir porosity is negative exponential, whereas the correlation between the total pore volume and coal reservoir porosity is positive linear. In comparison with the percolation and diffusion fractal dimensions, the comprehensive fractal dimension is better suited for characterizing the permeability of coal reservoirs. The fractal analysis of this paper is beneficial for understanding the relationship between the fractal characteristics of coal pores and properties. Full article

The CNT-PDMS composite has been widely adopted in flexible devices due to its high elasticity, piezoresistivity, and biocompatibility. In a wide range of applications, CNT-PDMS composite sensors were used for resistive strain measurement. Accordingly, the percolation threshold 2%~4% of the CNT weight ratio in the CNT-PDMS composite was commonly selected, which is expected to achieve the optimized piezoresistive sensitivity. However, the linear range around the percolation threshold weight ratio (2%~4%) limits its application in a stable output of large strain (>20%). Therefore, comprehensive understanding of the electromechanical, mechanical, and electrical properties for the CNT-PDMS composite with different CNT weight ratios was expected. In this paper, a systematic study was conducted on the piezoresistivity, Young’s modulus, conductivity, impedance, and the cross-section morphology of different CNT weight ratios (1 to 10 wt%) of the CNT-PDMS composite material. It was experimentally observed that the piezo-resistive sensitivity of CNT-PDMS negatively correlated with the increase in the CNT weight ratio. However, the electrical conductivity, Young’s modulus, tensile strength, and the linear range of piezoresistive response of the CNT-PDMS composite positively correlated with the increase in CNT weight ratio. Furthermore, the mechanism of these phenomena was analyzed through the cross-section morphology of the CNT-PDMS composite material by using SEM imaging. From this analysis, a guideline was proposed for large strain (40%) measurement applications (e.g., motion monitoring of the human body of the finger, arm, foot, etc.), the CNT weight ratio 8 wt% was suggested to achieve the best piezoresistive sensitivity in the linear range. Full article

Spin glasses are prototypical random systems modelling magnetic alloys. One important way to investigate spin glass models is to study domain walls. For two dimensions, this can be algorithmically understood as the calculation of a shortest path, which allows for negative distances or weights. This led to the creation of the negative weight percolation (NWP) model, which is presented here along with all necessary basics from spin glasses, graph theory and corresponding algorithms. The algorithmic approach involves a mapping to the classical matching problem for graphs. In addition, a summary of results is given, which were obtained during the past decade. This includes the study of percolation transitions in dimension from $d=2$ up to and beyond the upper critical dimension $d_u=6$ , also for random graphs. It is shown that NWP is in a different universality class than standard percolation. Furthermore, the question of whether NWP exhibits properties of Stochastic–Loewner Evolution is addressed and recent results for directed NWP are presented. Full article