Search Results (3)

This study proposed a standardized oilseed rape seedling-carrying potting molding method to improve the adaptability of mechanical transplanting of potting seedlings. This method aims to address the failure in seedling pick-up and transport during the mechanized transplanting of rapeseed pot seedlings, which is caused by matrix breakage and seedling damage. This study selected cylindrical oilseed rape seedling-carrying potting as the research object and investigated the relationship between the physical characteristics of seedling-carrying potting and the proportion of the composition of the matrix soil as well as the characteristics of seedling growth after planting. The optimal parameter combination of the matrix soil was obtained using Design-Expert 8.0.6 software: dry matter ratio of 4:1, compression ratio of 0.36, and moisture content of 45%. A single-factor test was conducted using a seedling-carrying potting test bed. According to the single-factor test results, the dry matter ratios (commercial substrate: clay loam mass ratios of 2:1, 3:1, and 4:1), matrix soil compression ratios (0.35, 0.40, and 0.45), and matrix soil moisture content (35%, 40%, and 45%) were selected as the factors of influence, while the drop loss rate, shear resistance, and scattering rate were used as the indicators of evaluation. The drop loss rate of seedling-carrying potting under this parameter combination was 1.5%, the shear resistance was 7.1 N, and the scattering rate was 34.9%. Validation tests were conducted on a seedling-carrying potting test bed, and the relative errors between the actual and simulated values of the drop loss rate, shear resistance, and scattering rate were 7.1%, 7.0%, and 8.4%, respectively, verifying the accuracy of the model and the optimized parameters. Comparison tests of the growth characteristics of the optimized seedling-carrying potting, hole-tray seedling, and bare seedling in field transplanting were conducted. The results displayed that root length, root diameter, root dry matter, chlorophyll content, and seedling vigor index consistently followed the same descending order: seedling-carrying potting > hole-tray seedlings > bare seedlings. Compared to hole-tray seedlings, the corresponding growth characteristics of seedling-carrying potting were 11.7%, 10%, 21.7%, 2.8%, and 27.8% higher, respectively. Compared to bare seedlings, they were 17.1%, 12.5%, 32.2%, 10.8%, and 32.7% higher, respectively. The seedling length, seedling width, plant taper angle, and dry matter mass of stem and leaves were, in descending order, greater in hole-tray seedlings, followed by seedling-carrying potting, and then bare seedlings. In comparison, the corresponding growth characteristics of seedling-carrying potting were 8.9%, 9.8%, 2.3%, and 30.6% higher than those of bare seedlings, respectively. Full article

Nursery trays are essential agricultural tools in rice production. Plastic nursery trays pose problems such as resource waste and environmental pollution. Biomass seedling trays are an effective way to achieve sustainable agricultural development. Previous research has been conducted on biomass seedling tray molding equipment and molding process, but the impact of raw material ratio on seedling tray molding quality and seedling growth is still unclear, and the ratio combination still needs further optimization. In this study, we used slurry concentration, pulp content, adhesive content, and the ratio of straw to cow manure as variables. We selected the bowl hole molding rate and the strong seedling index as evaluation indicators, and carried out biomass seedling tray forming experiments and seedling cultivation experiments. The response surface analysis method was used to optimize the raw material ratio of biomass seedling trays from the perspectives of forming effect and seedling quality. The results show that when the slurry concentration is 30%, the pulp content is 20%, the adhesive content is 530 g, and the mass ratio of straw to cow manure is 2:1; the bowl hole molding rate is 91.03%, and the strong seedling index is 0.22, indicating good molding effect and seedling growth. The verification test results indicate that the theoretical analysis results are accurate, and the model fitting is good. These research results provide a theoretical basis for the preparation of biomass seedling trays and technical support for achieving green development in agriculture. Full article

In response to the problems of low straw utilization efficiency and poor returning effect in Northeast China, this paper takes rice straw containing cow dung as the experimental material, and according to the characteristics of lignin glass transformation of the material, proposes a new method to prepare biomass seedling trays. The seedling trays prepared by this method can meet the needs of corn seedling cultivation and transplantation. To study the molding mechanism, scanning electron microscopy and a universal testing machine were used to compare the changes in the internal structure and mechanical properties of the regularly- and hot-compressed seedling trays before and after seedling raising. The results show that the material with water content of 23% has the best hot-pressing effect. The forming mechanism is: that the strength of the molded seedling tray resulted from the mechanical setting force of the multilayered stem fibers with a mosaic structure within the seedling tray. The adhesion and wrapping by lignin prevented water penetration from damaging the multilayered stem fibers and slightly improved their strength. The seedling tray made of straw and manure was completely degraded over 40 days, and the straw degradation rate was improved. This method can increase the overall quality and benefits of straw, providing a foundational reference for high-quality and high-efficiency straw utilization. Full article