Search Results (5)

This paper presents a study of the propagation of surface acoustic waves in a single and periodic array of metal strip overlays on the surface of layered substrates. Responses of reflected and transmitted surface acoustic waves due to various geometric design parameters of the grating arrays are investigated. An eight-dimensional matrix formulation based on Stroh formalism is adopted to analyze wave propagation in piezoelectric layered media. The dispersion curves for aluminum–zinc oxide films on glass substrates are determined using the surface impedance tensor method. A transfer matrix in terms of the state vectors in cooperation with continuity conditions on the edges of the grating array is used to determine the reflectivity and transmittance of the horizontally propagating surface acoustic waves. The analysis and simulation results show that when the surface acoustic wave is obliquely incident on an array of gratings and the strip width is equal to the gap between strips, the constructive interference of the reflected wave occurs at odd multiples of the strip width to a wavelength ratio of 0.25. When the strip width is unequal to the gap, the constructive interference of the reflected wave is an odd multiple of the strip width to a wavelength ratio of 0.5. An increase in the number of strips concentrates the reflectivity’s extreme frequencies, and an increase in the strip height increases the bandwidth of the extreme frequencies. Both of these increases strengthen the reflected wave’s constructive interferences. Full article

Two structures (Ag/ZnO/ITI/glass: #1 sample and Ag/ZnO/SiO₂/Si: #2 sample) are investigated, on the one hand, from the point of view of the formation of evanescent waves in the gratings of metal strips on the structures when the incident TEz wave in the radio frequency range is used. The simulation of the formation of evanescent waves at the edge of the Ag strips, with thicknesses in the range of micrometers, was carried out before the test in the subwavelength regime, with the help of a new improved transducer with metamaterial (MM) lenses. By simulation, a field snapshot was obtained in each sequence of geometry. The evanescent waves are emphasized in the plane XY, due to the scattering of the field on the edge of the strips. On the other hand, ZnO nanoparticles are investigated as a convenient high-efficiency biodetection material, where these structures were used as a biosensitive element to various enzymes (glucose, cholesterol, uric acid, and ascorbic acid). The obtained results demonstrate that the investigated structures based on ZnO nanostructures deposited on different supports are fast and sensitive for enzyme detection and can be successfully incorporated into a device as a biosensing element. Full article

Oil flowlines, the first “pipeline” system connected to the wellhead, are pipelines that are 5 to 30.5 cm (two to twelve inches) in diameter, most susceptible to corrosion, and very difficult to inspect. Herein, an external corrosion detection sensor for oil and gas pipelines, consisting of a semicircular plastic strip, a flat dog-bone-shaped sacrificial metal plate made out of the same pipeline material, and an optical fiber with Fiber Bragg Grating (FBG) sensors, is described. In the actual application, multiple FBG optical fibers are attached to an oil and gas pipeline using straps or strips or very large hose clamps, and, every few meters, our proposed corrosion detection sensor will be glued to the FBG sensors. When the plastic parts are attached to the sacrificial metals, the plastic parts will be deformed and stressed; thus, placing the FBG sensors in tension. When corrosion is severe at any given pipeline location, the sacrificial metal at that location will corrode till failure and the tension strain is relieved at that FBG Sensor location, and therefore, a signal is detected at the interrogator. Herein, the external corrosion detection sensor and its design equations are described, and experimental results, verifying our theory, are presented. Full article

The current stage of non-destructive evaluation techniques imposes the development of new electromagnetic methods that are based on high spatial resolution and increased sensitivity. Printed circuit boards, integrated circuit boards, composite materials with polymeric matrix containing conductive fibers, as well as some types of biosensors are devices of interest in using such evaluation methods. In order to achieve high performance, the work frequencies must be either radiofrequencies or microwaves. At these frequencies, at the dielectric/conductor interface, plasmon polaritons can appear, propagating between conductive regions as evanescent waves. Detection of these waves, containing required information, can be done using sensors with metamaterial lenses. We propose in this paper the enhancement of the spatial resolution using electromagnetic methods, which can be accomplished in this case using evanescent waves that appear in the current study in slits of materials such as the spaces between carbon fibers in Carbon Fibers Reinforced Plastics or in materials of interest in the nondestructive evaluation field with industrial applications, where microscopic cracks are present. We propose herein a unique design of the metamaterials for use in nondestructive evaluation based on Conical Swiss Rolls configurations, which assure the robust concentration/focusing of the incident electromagnetic waves (practically impossible to be focused using classical materials), as well as the robust manipulation of evanescent waves. Applying this testing method, spatial resolution of approximately λ/2000 can be achieved. This testing method can be successfully applied in a variety of applications of paramount importance such as defect/damage detection in materials used in a variety of industrial applications, such as automotive and aviation technologies. Full article

Metallic strip gratings (MSG) have different applications, ranging from printed circuits to filters in microwave domains. When they are under the influence of an electromagnetic field, evanescent and/or abnormal modes appear in the region between the traces, their utilization leading to the development of new electromagnetic nondestructive evaluation methods. This paper studies the behavior of MSGs in the sub-subwavelength regime when they are excited with TE_z or TM_z polarized plane waves and the slits are filled with different dielectrics. The appearance of propagating, evanescent and abnormal modes is emphasized using an electromagnetic sensor with metamaterials lens realized with two conical Swiss rolls, which allows the extraction of the information carried by the guided evanescent waves. The evanescent waves, manipulated by the electromagnetic sensor with metamaterial lenses, improve the electromagnetic images so that a better spatial resolution is obtained, exceeding the limit imposed by diffraction. Their theoretical and experimental confirmation opens the perspective for development of new types of sensors working in radio and microwave frequencies. Full article