Search Results (5)

Background: Surgical neck nonunions of the proximal humerus present a complex clinical challenge, especially in elderly patients with pre-existing glenohumeral arthritis. Reverse total shoulder arthroplasty (RTSA) offers a reliable treatment option in these cases; however, resection of the tuberosities may compromise joint stability, increase the risk of postoperative dislocation and compromise postoperative function. This article describes a reproducible RTSA technique that preserves and repairs the greater and lesser tuberosities, aiming to enhance construct stability and optimize outcomes. Methods: We present a 74-year-old female with underlying glenohumeral arthritis who underwent RTSA for a symptomatic surgical neck nonunion via an extended deltopectoral approach. The nonunion is first mobilized, and tuberosity osteotomies are performed. After implant placement, the tuberosities are secured to the implant, to each other, and to the humeral shaft. A cerclage suture is also passed circumferentially to reinforce the repair and prevent posterior gapping. Results: The patient regained her pre-injury level of function by her last follow-up. She had pain-free, active forward elevation to 110 degrees and radiographic evidence of maintained tuberosity reduction and healing. There was no evidence of instability. Conclusions: In conclusion, incorporating tuberosity preservation and repair into RTSA for proximal humerus nonunion may reduce dislocation risk and improve functional recovery in elderly, low-demand patients. Full article

Introduction: The aim of this study was to create a novel complication classification for osteosynthesis-related complications following angular stable plating of the proximal humerus subsuming the influence of these complications on clinical outcome in relation to fracture morphology and consequent revision strategies. A total of 1047 proximal humerus fractures with overall 193 osteosynthesis-associated complications (24.5%) were included. The following complication types could be clarified: complication Type 1 is defined by mild varus (<20°) or valgus displacement of the humeral head without resulting in a screw cutout through the humeral head cortex. Type 2a is defined by varus displacement (<20°) of the humeral head associated with screw cutout through the humeral head cortex. Type 2b complication is limited to displacement of the greater tuberosity, lesser tuberosity, or both tuberosities. Complication Type 2c is defined by severe varus dislocation (>20°) of the humeral head with screw cutout at the humeral head cortex. Complication Type 3 describes a displacement of the angular stable plate in the humeral shaft region with associated shaft-sided screw cutout, while the position of the humeral head remains static. Complication Type 4 is characterized by the occurrence of AVN with or without glenoidal affection (4a/b). Clinical outcome according to the constant score was mainly affected by type 2–4, leading to a deteriorated result. Depending on the type of complication, specific revision strategies can be considered. Additionally, more complex fracture patterns fostered the incidence of complications. Full article

Background: This study compared the healing rates of lesser tuberosity osteotomy (LTO) for anatomic total shoulder arthroplasty (TSA), repaired with either standard knot tying or a tensionable construct. Second, we evaluated LTO healing in stemmed and stemless prostheses and identified the patient characteristics associated with healing. Methods: An analysis of consecutive primary TSAs approached with an LTO performed by a single surgeon between 2016 and 2020 was conducted. In the first two years of the study period, the LTOs were repaired with four #2 polyblend sutures passed through drill tunnels and around a short press-fit stem, followed by manual knot tying. Subsequently, a tensionable construct with suture tapes (TCB) was universally adopted. The radiographic appearance of the LTO was evaluated at a minimum of six months postoperatively. Results: A total of 340 patients met the study criteria, including 168 with manual knot tying, 84 TCB repairs with a stemmed implant, and 88 TCB repairs with a stemless implant. There was no difference in the baseline demographics between the groups. The LTO healing rate of the manual knot tying group (85%) was lower than that of the stemmed (95%) and stemless (98%) TCB groups (p < 0.001). When directly comparing the LTO healing between the stemmed and stemless TCB groups, the differences were not significant (p = 0.44). Across all constructs, the body mass index (BMI) was higher in the displaced nonunion group (p = 0.04), with a failure rate of 9.4% for a BMI between 30 and 40, 12.5% for a BMI between 40 and 50, and 28.6% for a BMI > 50. The rate of tobacco use was higher in the displaced nonunion group (p = 0.037). Conclusion: A tensionable construct improves LTO healing compared to manual knot tying, irrespective of the implant type. In addition to the surgical technique, the patient factors that influence tuberosity healing include a greater BMI and tobacco use. Level of evidence: Level III, retrospective comparative study. Full article

Tuberosity healing and stem design can be outcome-dependent parameters in hemiarthroplasty for proximal humerus fractures (PHF). The relevance of fracture-specific stem design in reverse shoulder arthroplasty (RSA) is still a matter of debate. This retrospective study evaluates tuberosity healing and function for fracture specific stems (A) compared to conventional stems (B) in RSA for complex PHF in 26 patients (w = 21, mean age 73.5 years). Clinically, range of motion (ROM), Constant-Murley-Score (CS), Subjective Shoulder Value (SSV), and external rotation lag signs (ERLS) were evaluated. Healing of greater tuberosity (GT) and lesser tuberosity (LT), scapular notching, and loosening were examined radiologically. There were no statistical significant differences with regards to CS (A: 73 ± 11; B: 77 ± 9 points), SSV (A: 78% ± 11%; B: 84% ± 11%), external rotation (A: 18° ± 20°; B: 24° ± 19°), or internal rotation (A: 5.7 ± 2.2; B: 6.7 ± 2.8 CS-points) (p > 0.05). Mean forward flexion was superior for group A (p = 0.036). Consolidation of GT (82%) and LT (73%) was similar in both groups. Anatomical healing was slightly higher in group B (p > 0.05). Scapular notching was found in 27% (A) and 55% (B) (p > 0.05). RSA for PHF provides good to excellent clinical results. The quantitative and qualitative union rate for both cohorts was similar, indicating that fracture stems with open metaphyseal designs to allow for bone ingrowth do not improve tuberosity healing. ERLS correlates with a worse function in CS and ROM in all planes. Full article

A variation of subscapularis tear has been identified, named floating subscapularis, where the tendon is completely detached from the lesser tuberosity but is continuous with the tissue covering the bicipital groove. An accurate diagnosis can be made using arthroscopic observation with passive external and internal rotation of the affected shoulder, which shows mismatched movement between the humerus and the subscapularis tendon. The purpose of this study is to examine the prevalence of this particular tear pattern. Clinical records during the study period (from January 2011 to December 2017) were retrospectively examined. Overall, 1295 arthroscopic rotator cuff repair procedures were performed. Among these, the subscapularis tendon was repaired in 448 cases, and 27 cases were diagnosed as floating subscapularis. The prevalence of floating subscapularis was 6% in the subscapularis repair population. This particular tear pattern has not previously been described and it seems to be ignored. The floating subscapularis is thought to be the tear of the deep layer preserving the superficial layer connected to the greater tuberosity by fibrous extension of the soft tissue covering the bicipital groove. Full article