Search Results (5)

Herein, we report on the synthesis of Ni and Zn clusters on the surface of TiO₂ as well as their bimetallic NiZn analogs. The materials were prepared by incipient wet impregnation of colloidal TiO₂ followed by microwave (MW) irradiation to graft the clusters to TiO₂ surface. The materials were further immobilized onto glass slides and exhibited high surface area, high mechanical stability, and porosity with accessible pores. The main species responsible for visible light degradation of microcystin LR via the interface charge transfer (IFCT) of excited e⁻ to surface metal clusters were found to be O₂^•− and h⁺. The optimal nominal grafting concentration was 0.5 wt.% for Ni and 1.0 wt.% for Zn, while for the bimetal modification (NiZn), the optimal nominal concentration was 0.5 wt.%. Compared to monometallic, bimetallic grafting showed a lower kinetic constant, albeit still improved compared to bare TiO₂. Bimetal-modified titania showed a lower photocurrent compared to single metal-grafted TiO₂ and poorer interfacial charge transport, namely, more recombination sites—possibly at the interface between the Ni and Zn domains. This work highlights the efficiency of using MW irradiation for grafting sub-nano-sized metallic species to TiO₂ in a homogeneous way. However, further strategies using MW irradiation for the structural design of bimetallic cocatalysts can be implemented in the future. Full article

This review presents an update describing binary and ternary semiconductors involving interfacial charge transfer (IFCT) in composites made up by TiO₂, CuO, Ag₂O and Fe₂O₃ used in microbial disinfection (bacteria and viruses). The disinfection mechanism, kinetics and generation of reactive oxygen species (ROS) in solution under solar/visible light are discussed. The surface properties of the photocatalysts and their active catalytic sites are described in detail. Pathogenic biofilm inactivation by photocatalytic thin films is addressed since biofilms are the most dangerous agents of spreading pathogens into the environment. Full article

This study presents the first evidence for the photocatalytic performance of ZnO/Cu_xO hexagonal nanowires leading to sulfamethazine (SMT) degradation. The chemical composition of the nanowires was determined by X-ray fluorescence (XRF). The sample with the composition ZnO/Cu_{x = 1.25}O led to faster SMT-degradation kinetics. The SMT-degradation kinetics were monitored by high performance liquid chromatography (HPLC). The morphology of the hexagonal nanowires was determined by scanning electron microscopy (SEM) and mapped by EDX. The redox reactions during SMT degradation were followed by X-ray photoelectron spectroscopy (XPS). The interfacial potential between the catalyst surface and SMT was followed in situ under solar and indoor visible light irradiation. SMT-degradation was mediated by reactive oxidative species (ROS). The interfacial charge transfer (IFCT) between ZnO and Cu_xO is shown to depend on the type of light used (solar or visible light). This later process was found to be iso-energetic due to the potential energy positions of ZnO and Cu_xO conduction bands (cb). The intervention of surface plasmon resonance (LSPR) species in the SMT degradation is discussed. Full article

Photocatalytic antibacterial sol-gel coated substrates have been reported to kill bacteria under light or in the dark. These coatings showed non-uniform distribution, poor adhesion to the substrate and short effective lifetime as antibacterial surfaces. These serious limitations to the performance/stability retard the potential application of antibacterial films on a wide range of surfaces in hospital facilities and public places. Here, the preparation, testing and performance of flexible ultra-thin films prepared by direct current magnetron sputtering (DCMS) at different energies are reviewed. This review reports the recent advancements in the preparation of highly adhesive photocatalytic coatings prepared by up to date sputtering technology: High Power Impulse Magnetron Sputtering (HIPIMS). These latter films demonstrated an accelerated antibacterial capability compared to thicker films prepared by DCMS leading to materials saving. Nanoparticulates of Ti and Cu have been shown during the last decades to possess high oxidative redox potentials leading to bacterial inactivation kinetics in the minute range. In the case of TiO2CuOx films, the kinetics of abatement of Escherichia coli (E. coli) and methicillin resistant Staphylococcus aureus (MRSA) were enhanced under indoor visible light and were perceived to occur within few minutes. Oligodynamic effect was seen to be responsible for bacterial inactivation by the small amount of released material in the dark and/or under light as detected by inductively-coupled plasma mass spectrometry (ICP-MS). The spectral absorbance (detected by Diffuse Reflectance Spectroscopy (DRS)) was also seen to slightly shift to the visible region based on the preparation method. Full article

This review focuses on Cu/TiO₂ sequentially sputtered and Cu-TiO₂ co-sputtered catalytic/photocatalytic surfaces that lead to bacterial inactivation, discussing their stability, synthesis, adhesion, and antibacterial kinetics. The intervention of TiO₂, Cu, and the synergic effect of Cu and TiO₂ on films prepared by a colloidal sol-gel method leading to bacterial inactivation is reviewed. Processes in aerobic and anaerobic media leading to bacterial loss of viability in multidrug resistant (MDR) pathogens, Gram-negative, and Gram-positive bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO₂ and Cu. Surface properties of 2D TiO₂/Cu and TiO₂-Cu films are correlated with the bacterial inactivation kinetics in dark and under light conditions. The intervention of these antibacterial sputtered surfaces in health-care facilities, leading to Methicillin-resistant Staphylococcus Aureus (MRSA)-isolates inactivation, is described in dark and under actinic light conditions. The synergic intervention of the Cu and TiO₂ films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP), and high power impulse magnetron sputtering (HIPIMS) is reported in a detailed manner. Full article