Search Results (16)

The global oil and gas exploration targets are gradually moving towards a new field of oil and gas accumulation with nanopore throats, ranging from millimeter scale to micro-nano pore throats. The development method of tight oil reservoirs is different from that of conventional oil reservoirs, and the development efficiency is constrained. Therefore, it is necessary to construct a nanoscale fluid with strong diffusion and dispersion and improve its permeability, suction, and displacement capabilities. Under the background of CCUS, carbon dioxide flooding is a better way to develop tight reservoirs. However, in order to solve the problem of gas channeling, this paper developed a carbon dioxide-responsive graphene point type surfactant, which has a good gas–liquid synergistic effect. At the same time, graphene nanomaterials are carbon-based and create no environmental damage in oil reservoirs. In this study, graphene quantum dots (GQDs) were prepared using the hydrothermal method, and functional graphene quantum dots (F-GQDs) responsive to carbon dioxide stimulation were synthesized by covalent grafting of amidine functional groups. By characterizing its structure and physical and chemical properties, and by conducting imbibition simulation experiments, its imbibition and drainage ability in nanopore throats is elucidated. Infrared spectrum measurement shows that after functional modification, the quantum dots exhibited new characteristic peaks at 1600 cm⁻¹ to 1300 cm⁻¹, considering the N-H plane-stretching characteristic peak. The fluorescence spectra showed that the fluorescence intensity of F-GQDs was increased after functional modification, which indicated that F-GQDs were successfully synthesized. Through measurements of interfacial activity and adhesion work calculations, the oil–water interfacial tension can achieve ultra-low values within the range of 10⁻² to 10⁻³ mN/m. Oil sand cleaning experiments and indoor simulations of spontaneous imbibition in tight cores demonstrate that F-GQDs exhibit effective oil-washing capabilities and a strong response to carbon dioxide. When combined with carbon dioxide, the system enhances both the rate and efficiency of oil washing. Imbibition recovery can reach more than 50%. The research results provide a certain theoretical basis and data reference for the efficient development of tight reservoirs. Full article

Cascading landslides are specific multi-hazard events in which a primary movement triggers successive landslide processes. Areas with dynamic and quickly changing environments are more prone to this type of phenomena. Both the kind and the evolution velocity of a landslide depends on the materials involved. Indeed, rockfalls are generated when rocks fall from a very steep slope, while debris flow and/or mudslides are generated by fine materials like silt and clay after strong water imbibition. These events can amplify the damage caused by the initial trigger and propagate instability along a slope, often resulting in significant environmental and societal impacts. The Morino-Rendinara cascading landslide, situated in the Ernici Mountains along the border of the Abruzzo and Lazio regions (Italy), serves as a notable example of the complexities and devastating consequences associated with such events. In March 2021, a substantial debris flow event obstructed the Liri River, marking the latest step in a series of landslide events. Conventional techniques such as geomorphological observations and geological surveys may not provide exhaustive information to explain the landslide phenomena in progress. For this reason, UAV image acquisition, InSAR interferometry, and pixel offset analysis can be used to improve the knowledge of the mechanism and kinematics of landslide events. In this work, the interferometric data ranged from 3 January 2020 to 24 March 2023, while the pixel offset data covered the period from 2016 to 2022. The choice of such an extensive data window provided comprehensive insight into the investigated events, including the possibility of identifying other unrecorded events and aiding in the development of more effective mitigation strategies. Furthermore, to supplement the analysis, a specific finite element method for slope stability analysis was used to reconstruct the deep geometry of the system, emphasizing the effect of groundwater-level flow on slope stability. All of the findings indicate that major landslide activities were concentrated during the heavy rainfall season, with movements ranging from several centimeters per year. These results were consistent with numerical analyses, which showed that the potential slip surface became significantly more unstable when the water table was elevated. Full article

The global shale gas resources are huge and have good development prospects, but shale is mainly composed of nanoscale pores, which have the characteristics of low porosity and low permeability. Horizontal drilling and volume fracturing techniques have become the effective means for developing the shale reservoirs. However, a large amount of mining data indicate that the fracturing fluid trapped in the reservoir will inevitably cause hydration interaction between water and rock. On the one hand, the intrusion of fracturing fluid into the formation causes cracks to expand, which is conducive to the formation of complex fracture networks; on the other hand, the intrusion of fracturing fluid into the formation causes the volume expansion of clay minerals, resulting in liquid-phase trap damage. At present, the determination of well closure time is mainly based on experience without theoretical guidance. Therefore, how to effectively play the positive role of shale hydration while minimizing its negative effects is the key to optimizing the well closure time after fracturing. This paper first analyzes the shale pore characteristics of organic pores, clay pores, and brittle mineral pores, and the multi-pore self-absorption model of shale is established. Then, combined with the distribution characteristics of shale hydraulic fracturing fluid in the reservoir, the calculation model of backflow rate and shut-in time is established. Finally, the model is validated and applied with an experiment and example well. The research results show that the self-imbibition rate increases with the increase in self-imbibition time, and the flowback rate decreases with the increase in self-imbibition time. The self-imbibition of slick water is the maximum, the self-imbibition of breaking fluid is the minimum, and the self-imbibition of mixed fluid is the middle, and the backflow rates of these three liquids are in reverse order. It is recommended the shut-in time of Longmaxi Formation shale is 17 days according to the hydration and infiltration model. Full article

Tissue engineering is an interdisciplinary field that develops new methods to enhance the regeneration of damaged tissues, including those of wounds. Polymer systems containing bioactive molecules can play an important role in accelerating tissue regeneration, mitigating inflammation process, and fighting bacterial infection. Chitosan (CS) has attracted much attention regarding its use in wound healing system fabrication thanks to its biocompatibility, biodegradability, and the presence of functional groups in its structure. In this work, bioactive chitosan-based membranes were obtained by both chemical and physical modifications of the polymer with glycidyl methacrylate and glycerol (GLY), respectively. The most suitable GLY concentration to obtain wound healing systems with good elongation at break, a good water vapor transmission rate (WVTR), and good wettability values was 20% (w/w). Afterwards, the membranes were crosslinked with different concentrations of ethylene glycol dimethacrylate (EGDMA). By using a concentration of 0.05 mM EGDMA, membranes with a contact angle and WVTR values suitable for the application were obtained. To make the system bioactive, 3,4-dihydrocinnamic acid (HCAF) was introduced into the membranes, either by imbibition or chemical reaction, using laccase as a catalyst. Thermal and mechanical analyses confirmed the formation of a cohesive network, which limited the plasticizing effect of GLY, particularly when HCAF was chemically bound. The HCAF-imbibed membrane showed a good antioxidant and antimicrobial activity, highlighting the potential of this system for the treatment of wound healing. Full article

Coating porosity is an important property that supports solid-gas and solid-liquid exchange that can either enhance various science and technological applications or promote damage if not properly controlled. However, non-destructive instrumental techniques for the measurement of porosity on coated walls or surfaces can be quite challenging. Here, a seamless capillary rise technique has been used to determine both the thickness and porosity of a thin silica coating. Uniform coatings were prepared from 5 wt% hydrophobic fumed silica in absolute ethanol and spin-coated at 500–8000 rpm on glass slides. Capillary imbibition of squalane was then controlled into known areas of the resulted hydrophobic nano-porous coatings. The mass of the solid (silica) and the infiltrated oil (squalane) were gravimetrically measured. The porosity of the material was calculated as the percentage fraction of the pore volume while the film thickness was determined as the ratio of the total volume to the area of coverage. Mean values of the porosity and coating thickness calculated from capillary impregnation technique were 86 ± 2% and 3.7 ± 0.2 μm, respectively. The coating thickness obtained was comparable with those revealed by SEM and Dektak profiler measurements. This study highlights the effectiveness of capillary rise as a simple and cost-effective non-destructive technique for assessment of coating thickness and porosity. Full article

In the last decades, the Rif area in Morocco has been frequently affected by soil erosion due to intense rainfall events. In order to help farmers improve their lives and avoid damages caused by this phenomenon, a management project (the MCA Project) aiming to grow fruit trees has been realized. The objective of this study was to evaluate, in three provinces of Morocco, the effect on the hydrological response of selected erosion control management techniques combined with olive tree plantations. The investigated variables were the final infiltration (If), the imbibition of rainwater (Pi), the runoff coefficient (Kr), and the soil detachment (D). In particular, for each investigated soil utilization, three replications of a rain simulation test (80 mm/h) and soil sampling were conducted. Results for surface conditions demonstrate that under vegetation in matorral and fallow, the surface is covered at more than 75% with a high content of organic matter (OM) at 4.5% and 2.6%, respectively. Despite the compaction observed in those land uses, the surface area opened exceeded 90% in the study area. Regarding the soils physical properties, they were rich in silt at more than 40%; the rate of porosity is high where bulk density is low. At the Taounate site, low porosity was at 62% in fallow and at 55% in plowing, with high densities of 1.01 g/cm² and 1.2 g/cm², respectively. Tests also demonstrate that vegetation has an important role in moisture conservation in the depths of 0 to 10 cm at all sites with macroagregate stability (MA%) compared to plowing sites. In terms of soil hydrology, vegetation reduces the runoff because, under matorral (it was at 0%), it avoids soil erosion. Full article

Agriculture depends on the ability of seeds to survive until the next planting season under ambient conditions that may be averse to seed quality even when the seed is in a quiescent state. Seed priming invigorates seeds, but the impact on the longevity of seeds has limited its adoption. This study investigated the effect of the storage of primed rice seed on seed viability, vigor, and longevity. Three seed priming methods were employed on the rice cultivar New Rice for Africa (NERICA 4) seeds. Subsequently, the seeds were stored for 120 days at 25 °C and 65% relative humidity, simulating the ambient seed storage conditions of the tropics and sub-tropics. The primed seed recorded increased vigor compared to the non-primed seed until 90 days of storage. However, seed storage for 120 days reduced seed vigor and viability for all the seeds. The results indicated a significant reduction in seed vigor, increased solute leakage, generation of hydrogen peroxide, and accumulation of malondialdehyde after storage. Priming enhances cell membrane integrity and maintains seed vigor in storage at near ambient conditions long enough before reversal of its performance by the storage conditions. This assures that primed seed can either be stored until the following planting season or remain viable in the soil during delayed germination. Full article

Hydraulic fracturing of shale gas reservoirs is characterized by large fracturing fluid consumption, long working cycle and low flowback efficiency. Huge amounts of fracturing fluid retained in shale reservoirs for a long time would definitely cause formation damage and reduce the gas production efficiency. In this work, a pressure decay method was conducted in order to measure the amount of fracturing fluid imbibition and sample permeability under the conditions of formation temperature, pressure and adsorbed methane in real time. Experimental results show that (1) the mass of imbibed fracturing fluid per unit mass of shale sample is 0.00021–0.00439 g/g considering the in-situ pressure, temperature and adsorbed methane. (2) The imbibition and flowback behavior of fracturing fluid are affected by the imbibition or flowback pressure difference, pore structure, pore surface properties, mechanical properties of shale and mineral contents. (3) 0.01 mD and 0.001 mD are the critical initial permeability of shales, which could be used to determine the relationship between the formation damage degree and the flowback pressure difference. This work is beneficial for a real experimental evaluation of shale formation damage induced by fracturing fluid. Full article

Cold atmospheric pressure plasma (CAPP) is widely used in medicine for the treatment of diseases and disinfection of bio-tissues due to its antibacterial, antiviral, and antifungal properties. In agriculture, CAPP accelerates the imbibition and germination of seeds and significantly increases plant productivity. Plasma is also used to fix molecular nitrogen. CAPP can produce reactive oxygen and nitrogen species (RONS). Plasma treatment of bio-tissue can lead to numerous side effects such as lipid peroxidation, genotoxic problems, and DNA damage. The mechanisms of occurring side effects when treating various organisms with cold plasma are unknown since RONS, UV-Vis light, and multicomponent biological tissues are simultaneously involved in a heterogeneous environment. Here, we found that CAPP can induce in vitro oxidation of the most common water-soluble redox compounds in living cells such as NADH, NADPH, and vitamin C at interfaces between air, CAPP, and water. CAPP is not capable of reducing NAD⁺ and 1,4-benzoquinone, despite the presence of free electrons in CAPP. Prolonged plasma treatment of aqueous solutions of vitamin C, 1,4-hydroquinone, and 1,4-benzoquinone respectively, leads to their decomposition. Studies of the mechanisms in plasma-induced processes can help to prevent side effects in medicine, agriculture, and food disinfection. Full article

Shale reservoirs are characterized by extremely low porosity and permeability, poor connectivity, and high content of clay minerals. This leads to the reservoir being vulnerable to imbibition damage caused by foaming agent solutions during foam drainage gas recovery. It results in the decrease of reservoir permeability and the reduction of gas well production and ultimate recovery. Therefore, as the most commonly used foam drainage gas production, it is particularly important. This study is structured as follows. First, we analyze and evaluate the characteristics of shale reservoirs within the target area, and that of mineral composition and microscopic pore throat structures. Second, we study foaming agent types and two types are selected to be applied in subsequent sensitivity tests. Simultaneously, the nuclear magnetic resonance (NMR) method was used to study the microscopic characteristics of reservoir damage and imbibition damage of shale, caused by the impact of foaming agent solutions during the foam drainage and gas recovery processes. Finally, it is concluded that the degree of damage to the core permeability is minimized when the concentration of foaming agents is 0.4–0.6%. A trend has been established for increased damage to the cores with increasing exposure time. Additionally, this study provides technical guidance for damage evaluation and reservoir protection in shale reservoir exploitation. Full article

This study aims to develop and evaluate fracturing nanofluids from the laboratory to the field trial with the dual purpose of increasing heavy crude oil mobility and reducing formation damage caused by the remaining fracturing fluid (FF). Two fumed silica nanoparticles of different sizes, and alumina nanoparticles were modified on the surface through basic and acidic treatments. The nanoparticles were characterized by transmission electron microscopy, dynamic light scattering, zeta potential and total acidity. The rheological behavior of the linear gel and the heavy crude oil after adding different chemical nature nanoparticles were measured at two concentrations of 100 and 1000 mg/L. Also, the contact angle assessed the alteration of the rock wettability. The nanoparticle with better performance was the raw fumed silica of 7 nm at 1000 mg/L. These were employed to prepare a fracturing nanofluid from a commercial FF. Both fluids were evaluated through their rheological behavior as a function of time at high pressure following the API RP39 test, and spontaneous imbibition tests were carried out to assess the FF’s capacity to modify the wettability of the porous media. It was possible to conclude that the inclusion of 7 nm commercial silica nanoparticles allowed obtaining a reduction of 10 and 20% in the two breakers used in the commercial fracture fluid formulation without altering the rheological properties of the system. Displacement tests were also performed on proppant and rock samples at reservoir conditions of overburden and pore pressures of 3200 and 1200 psi, respectively, while the temperature was set at 77 °C and the flow rate at 0.3 cm³/min. According to the effective oil permeability, a decrease of 31% in the damage was obtained. Based on these results, the fracturing nanofluid was selected and used in the first worldwide field application in a Colombian oil field with a basic sediment and water (BSW%) of 100 and without oil production. After two weeks of the hydraulic fracture operation, crude oil was produced. Finally, one year after this work, crude oil viscosity and BSW% kept showing reductions near 75% and 33%, respectively; and having passed two years, the cumulative incremental oil production is around 120,000 barrels. Full article

Tight sandstone gas is a significant unconventional natural gas resource, and has been exploited economically mostly through the application of hydraulic fracturing technology in recent decades. However, formation damage occurs when fracturing fluid percolates into the pores inside sandstones through imbibition driven by capillary pressure during fracturing operations. In this work, the formation damage resulting from the whole operation process composed of fracturing, well shut-in and flowback, and the degree of damage at different moments were investigated through core flow experiments and the low-field Nuclear Magnetic Resonance (NMR) technique. The results show that imbibition damage occurs starting from the contact surface between the formation and the fracturing fluid, which penetrates into an increasingly deep position with time down to a certain depth. The T2 spectra of NMR at different moments indicates that fracturing fluid initially enters the small pores, followed by the large pores due to the larger capillary pressure in the former. Thus, the sandstone cores with low permeability incur a higher degree of damage due to their stronger capability of retaining fracturing fluid compared to high-permeability cores. The front position of the fracturing fluid imbibition at different moments, along with the degree of damage, were characterized through the one-dimensional encoding processing of the NMR signal. These results underlie the effective strategy to relieve formation damage resulting from imbibition during hydraulic fracturing operations. Full article

The water-blocking effect is a serious problem when developing tight sandstone gas reservoirs, which can cause a sharp reduction in gas production. Wettability alteration of near-wellbore sand rock surface from superhydrophilicity to superhydrophobicity is an effective method to decrease capillary pressure. In this study, a superhydrophobic fluorinated nano-emulsion was synthesized via a soap-free emulsion polymerization process using methacryloxyethyl trimethyl ammonium chloride, trifluoctyl methacrylate, and styrene as monomers. The effect of the fluorinated monomer concentration on wettability alteration was evaluated by measuring the contact angle of the formation water droplet on the modified glass slides using nano-emulsions with different fluorinated monomer concentrations. The results showed that the nano-emulsion had a good dispersibility and homogeneous particle size of around 90 nm, and with the increase in fluorinated monomer concentration, the contact angle increased. The contact angle was the largest when the fluorinated monomer mass rate concentration reached 50%. The adsorption of nanoparticles could alter the rock wettability from a super hydrophilic state (θ = 7°) to a superhydrophobic state (θ = 150°). The spontaneous imbibition experiments showed that the formation water adsorption quality of the core decreased by 49.7% after being modified by the nano-emulsion. The nano-emulsion showed a good superhydrophobicity and had the potential to be used to reduce the water-blocking damage in the tight gas reservoirs. Full article

[D-Leu¹]MC-LR and MC-LR, two microcystins differing in one amino acid, constitute a sanitary and environmental problem owing to their frequent and concomitant presence in water bodies of the Americas and their association with human intoxication during recreational exposure to cyanobacterial bloom. Present in reservoirs used for irrigation as well, they can generate problems in the development of crops such as Phaseolus vulgaris, of nutritional and economic interest to the region. Although numerous works address the toxic effects of MC-LR, information on the toxicity of [D-Leu¹]MC-LR is limited. Our objective was to study the toxic effects of [D-Leu¹]MC-LR and MC-LR (3.5 µg/ml) on P. vulgaris after a single contact at the imbibition stage. Our findings indicate that 10 days post treatment, [D-Leu¹]MC-LR generates morphological and physiological alterations more pronounced than those caused by MC-LR. In addition to the alterations produced by [D-Leu¹]MC-LR in the development of seedlings and the structure of the leaves, roots and stems, we also found alterations in leaf stomatal density and conductivity, a longer delay in the phototropic response and a decrease in the maximum curvature angles achieved with respect to that observed for MC-LR. Our findings indicate that these alterations are linked to the greater inhibition of phosphatase activity generated by [D-Leu¹]MC-LR, rather than to oxidative damage. We observed that 30 days after treatment with MC-LR, plants presented better development and recovery than those treated with [D-Leu¹]MC-LR. Further studies are required on [D-Leu¹]MC-LR and MC-LR toxicity and their underlying mechanisms of action. Full article

The remediation of contaminated sites using plant-based techniques has gained increasing attention in recent decades. However, information on the effects of contaminant imbibition on seed viability and germination rates are often lacking in the literature. To this end, our research investigated, by means of an event-time model, the effect of diesel fuel imbibition on the seed viability and germination rate of Medicago sativa, a plant species with great potential for remediation of organic contaminants. The event-time model provided an accurate and biologically relevant method for analysing germination data. Our results reveal that the direct imbibition of diesel fuel by M. sativa seeds for ≤48 h, or their exposure to soil diesel fuel concentrations of 0–10 g/kg diesel fuel, affects their germination rates, as shown by increasing t₅₀ values from 90.6 (±2.78) to 114.2 (±2.67) hours, without significantly affecting seed viability. On the other hand, diesel fuel imbibition of longer duration, or the exposure of M. sativa seeds to ≥20 g/kg diesel fuel-contaminated soils, leads to no further effect on time to seed emergence. Instead, these conditions compromise seed viability, resulting in a decrease in the proportion of germinated seeds from 0.91 (±0.03) in 10 g/kg diesel fuel contaminated soil to 0.84 (±0.04) and 0.70 (±0.05) in 20 and 30 g/kg diesel fuel-contaminated soils, respectively. The fact that low concentrations of diesel fuel and 0–48 h of direct imbibition delayed seed emergence without adversely affecting the percentage of viable seeds suggests that this inhibitory effect on germination at low diesel fuel exposure could be attributed more to physical constraints rather than biological damage on the seeds. The models used in this study provide an accurate and biologically relevant method for the analyses of germination data. This is vital since expensive germination experiments, be it in the field of toxicology or agriculture, deserve to be accurately analysed. Full article