Search Results (3)

Strong mine pressure often emerges when the working face of the lower coal seam in a closely spaced coal seam system passes through the remaining coal pillar in the overlying goaf. This study investigates the law of overburden movement and the manifestation of mine pressure during mining under the remaining coal pillar. A physical model measuring 2.5 × 0.2 × 1.503 m is constructed. Fiber Bragg grating sensing technology (FBG) and Brillouin optical time domain analysis technology (BOTDA) are employed in the physical model experiment to monitor the internal strain of the overlying rock as the working face advances. This study determines the laws of overlying rock fracture and working face pressure while mining coal seams beneath the remaining coal pillar. It analyzes the relationship between the pressure at the working face and the strain characteristics of the horizontally distributed optical fiber. A fiber grating characterization method is established for the stress evolution law of overlying rock while passing the remaining coal pillar. The experimental results indicated that the fracture angle of overlying rock gradually decreases during the mining stage through and after the coal pillar. In the mining stage through the coal pillar, the cycle pressure step distance of the working face is reduced by 33.3% compared to the stage after mining through the coal pillar. Initially, the strain pattern of the horizontal optical fiber is unimodal when pressure is first applied to the working face, and it transitions from unimodal to bimodal during periodic pressure. The peak value of fiber Bragg grating compressive strain and the range of influence of advanced support pressure are 3.6 times and 4.8 times, respectively, before passing through the remaining coal pillar. Finally, the accuracy of the FBG characterization method is verified by comparing it to the monitoring curve of the coal seam floor pressure sensor. The research results contribute to applying fiber optic sensing technology in mining physical model experiments. Full article

This new sensor design provides good volume sensitivity (around 1600 nm/RIU) via collinear diffraction by the asymmetric grating placed in the waveguide vicinity. It provides the mode transformation between the fundamental TE₀ and the first TE₁ modes of the silicon wire (0.22 μm by a 0.580 μm cross-section) in the water environment. In order to provide the wavelength interrogation with a better extinction ratio for the measuring signal, the grating design is incorporated with the mode filter/demultiplexer. It selects, by the compact directional coupler (maximum 4 μm wide and 14 μm long), only the first guided mode (close to the cutoff) and transmits it with small excess loss (about −0.5 dB) to the fundamental TE₀ mode of the neighboring single mode silicon wire, having variable curvature and width ranging from 0.26 μm to 0.45 μm. At the same time, the parasitic crosstalk of the input TE₀ mode is below −42 dB, and that provides the option of simple and accurate wavelength sensor interrogation. The environment index is measured by the spectral peak position of the transmitted TE₀ mode power in the output single mode silicon wire waveguide of the directional coupler. This type of optical sensor is of high sensitivity (iLOD~ 2.1 × 10⁻⁴ RIU for taking into account the water absorption at 1550 nm) and could be manufactured by modern technology and a single-step etching process. Full article

Analysis of trends in the development of silicon photonics shows the high efficiency regarding the creation of optical sensors. The concept of bimodal sensors, which suggests moving away from the usual paradigm based only on single-mode waveguides and using the inter-mode interaction of guided optical waves in a two-mode optical waveguide, is developed in the present paper. In this case, the interaction occurs in the presence of an asymmetric periodic perturbation of the refractive index above the waveguide surface. Such a system has unique dispersion properties that lead to the implementation of collinear Bragg diffraction with the mode number transformation, in which there is an extremely high dependence of the Bragg wavelength on the change in the refractive index of the environment. This is called the “effect of dispersion-enhanced sensitivity”. In this paper, it is shown by numerical calculation methods that the effect can be used to create optical sensors with the homogeneous sensitivity higher than 3000 nm/RIU, which is many times better than that of sensors in single-mode waveguide structures. Full article