Search Results (31)

In high-orbit space missions, the significant attenuation of Global Navigation Satellite System (GNSS) signals due to long transmission distances and complex environmental interferences has led to a drastic degradation in the accuracy of traditional positioning models, which has attracted great attention in recent years. Although multi-system GNSS fusion positioning can alleviate the problem of insufficient satellite visibility, the existing methods are difficult to effectively cope with the challenges of multi-source noise coupling and inter-system error differences unique to high orbit. In this paper, we propose an adaptive GNSS positioning optimization framework for a high-orbit environment, which improves the orbiting reliability under complex signal conditions through dynamic weight allocation and a multi-system cooperative strategy. Different from the traditional weighting model, this method innovatively constructs a two-layer optimization mechanism: (1) Based on BP neural network, it evaluates the noise characteristics of pseudo-range observations in real time and realizes the adaptive suppression of receiver thermal noise, ionospheric delay, etc.; (2) it introduces Helmert variance component estimation to optimize the weighting ratio of GPS, GLONASS, BeiDou, and Galileo and reduces the impact of signal heterogeneity on the positioning solution of the multi-system. Simulation results show that the new method reduces the root-mean-square error of positioning by 32.8% compared with the traditional algorithm to 97.72 m in typical high-orbit scenarios and significantly improves the accuracy loss caused by the defective satellite geometrical configurations under multi-system synergy. Full article

The inter-system-like bias between the regional (BDS-2) and global (BDS-3) constellation of the BeiDou Navigation Satellite System (BDS) has been identified on common B1I pseudo-range observations. In this study, its characteristics are investigated with tracking data from the International GNSS Service (IGS) and International GNSS Monitoring and Assessment System (iGMAS) network. Firstly, the satellite-specific inter-system-like bias is calculated and the dependency on satellite is observed. Clearly noticeable discrepancies on BDS-2 and BDS-3 can be identified. Hence, the constellation-specific inter-system-like bias is estimated. Biases for all receivers are quite stable, with standard derivation (STDev) less than 0.2 m in average. The bias shows clear dependence on the receiver, while the firmware and antenna have limited but not negligible impacts, particularly for Trimble NetR9 and Alloy receivers. The Trimble NetR9 with TRM59800.00 antenna shows noticeable discrepancy up to about 1.5 m with different antenna, and the bias of the Trimble Alloy 5.37 jumps about 2.4 m with respect to later firmware. In addition, clear annual variations are observed for stations ABPO and MIZU with Septentrio POLARX5 5.3.2 and ASTERX4 4.4.2 receivers, respectively. Furthermore, the impacts of the biases on the BDS orbit and clock solutions are analyzed. Once BDS-2 and BDS-3 are treated as two independent systems, the root mean square (RMS) of code and carrier phase residuals can be reduced by around 9.3 cm and 0.23 mm, respectively, while the three-dimensional orbit consistency is improved by 6.8%, mainly in the tracking direction. Satellite laser ranging (SLR) shows marginal impacts on IGSO and MEO satellites. However, the SLR residual of C01 shifts −13.2 cm, resulting in a smaller RMS value. In addition, the RMS of linear clock fitting is reduced from 0.050 ns to 0.038 ns for BDS-3 MEO satellites in average. Full article

A concept that has been explored as a means to obtain decimeter-level positioning accuracy with global navigation satellite systems (GNSSs) is meta-signal processing (MSP), which treats several stand-alone GNSS signals as a single composite wideband signal. BeiDou Navigation Satellite System (BDS) III already offers with the B1I+B1C signal a meta-signal, while the forthcoming Galileo (GAL) E1D could be combined with E1B or E1C if the E1D signal is broadcast with a frequency offset to the L1/E1 carrier frequency. This would boost the ranging performance of GAL open service (OS) in the upper L-band through MSP. However, the cross-correlation function (CCF) of meta-signals contain numerous high side-maxima which can, when wrongly identified as the main peak, lead to significant pseudo-range errors of multiple meters. The probability of such a false lock is known to increase with decreasing signal-to-noise ratios but can significantly increase even further due to imperfections in the analog hardware components (e.g., linear and non-linear effects of a high-power amplifier (HPA), an output multiplexer (OMUX), a transmitter filter, and a front-end receiver), as these can distort the CCF. One remaining question is whether meta-signals are a well-suited approach to reliably increase ranging performance in the presence of payload and receiver distortions. This study presents the first systematic assessment of the robustness of several potential meta-signal options enabled by a forthcoming GAL E1D signal for different levels of distortion. The results show significant performance gains but also indicate constraints regarding the choice of signals when considering MSP under the influence of distortions. Full article

With the continuous construction and development of the BeiDou navigation satellite system (BDS), its positioning performance is constantly being improved. In this study, the positioning performance of different frequency combinations of BDS-3/GPS/Galileo in the Asia-Pacific region was investigated. The precision products of Wuhan University and the observation data of nine MGEX stations were selected to compare and analyze the B1I\B1C\B2a\B3I and L1\E1 pseudo-range Standard Point Positioning (SPP) and B1IB2a\B1IB3I\B1CB2a\B1CB3I\B2aB3I\L1L2\E1E5a precise point positioning (PPP) performance, while B1I\B3I\L1 SPP and B1IB3I PPP were investigated using BDS-2 with QZSS supplemented with BDS-3 and GPS. The experimental results showed that the positioning precision of BDS-3/GPS/Galileo SPP was in the order of B1C > E1 > L1 > B1I > B3I > B2a, and it was not significantly improved after BDS-2 and QZSS were added. Moreover, for the PPP of different frequency combinations, the convergence speed was in the order of L1L2 > B1IB3I > E1E5a > B1CB3I > B1CB2a > B1IB2a > B2aB3I. After adding BDS-2, B1IB3I improved by about 11% in static mode and 27% in kinematic mode, which was similar to the L1L2 frequency combination. The positioning precision of different frequency combinations of BDS-3/GPS/Galileo was B1IB3I > B1CB3I > L1L2 > E1E5a > B1B2a > B1CB2a > B2aB3I. In static mode, after adding BDS-2, B1IB3I did not show significant improvement in the plane direction, and showed ~61% improvement in the elevation direction, and ~67% in the three-dimensional (3D) direction. In kinematic mode, after adding BDS-2, B1IB3I was improved by about 16% in the E direction, the N direction did not show significant change, it improved by ~38% in the U direction and by ~70% in the 3D direction. In general, the positioning performance of BDS-3 was slightly better than those of GPS and Galileo in the Asia-Pacific region, and it is believed that with the continuous development of BDS, its positioning performance will surely be improved further. Full article

Many studies have focused on the smartphone-based global navigation satellite system (GNSS) for its portability. However, complex urban environments, such as urban canyons and tunnels, can easily interfere with GNSS signal qualities. Current smartphone-based positioning technologies using the GNSS signal still pose great challenges. Since the last satellite of the BeiDou navigation system (BDS) was successfully launched on 23 June 2020, it is possible to use a low-cost Android device to realize the localization based on the BDS signals worldwide. This research focuses on smartphone-based outdoor pedestrian navigation utilizing the GPS/BDS multi-constellation system. To improve the localization accuracy, we proposed the Weighted Factor Graph Optimization localization model (W-FGO). In this paper, firstly, we evaluate the signal qualities of the BDS via the data collected by the static experiment. Then, we structure the cost function based on the pseudo-range and the time series data for the traditional Factor Graph Optimization (FGO). Finally, we design the weight model based on the signal quality of each satellite and the time fading factor to further improve the localization accuracy of the conventional FGO method. An Android smartphone is utilized to collect the GNSS data for the evaluation and the localization. The experiment results demonstrate the superior performance of the proposed method. Full article

Due to the influence of indoor space environments, the carrier phase information obtained by the BeiDou pseudo-satellite often has the issue of cycle slips, which makes the user unable to carry out high-precision positioning. Aiming at the problem of ambiguity resolution (AR) and location in large-scale occluded space (LSOS), a factor graph (FG) position method based on group phase ranging ambiguity estimation of BeiDou pseudolite is proposed. Firstly, by introducing the principle of group phase period quantization and utilizing the multi-frequency characteristic of the BeiDou pseudo-satellite, the carrier phase propagation ambiguity of the BeiDou pseudo-satellite can be estimated quickly. On this basis, by introducing the shuffled frog leading algorithm (SFLA) assisted factor graph optimization location estimation method, the BeiDou pseudo-satellite positioning process in LSOS is realized. The experimental results show that the proposed method can solve the problem of fast estimation of ranging ambiguity of BeiDou pseudolite in LSOS, and the ranging accuracy can be improved to two wavelength ranges. In the further location experiment, it is found that the algorithm can not only guarantee the real-time location output but also improve the location precision to sub-meter level under the multi-frequency combination; the optimal location test precision is 9 cm, the maximum positioning error is 50 cm. This method successfully solves the problem wherein the BeiDou pseudo-satellite cannot provide real-time, continuous, and high-precision positioning in LSOS. Full article

The global navigation satellite system (GNSS) precise point positioning (PPP) technique has been commonly applied to structural displacement monitoring. Considering the sheltering effect, GNSS receivers are regularly mounted on the top of a structure, but the structure is often not a rigid body; therefore, the receiver should also be mounted on the wall of the structure. Combining five constellations, GNSS can effectively reduce the sheltering effect. Therefore, this study attempts to apply the five-constellation PPP technique to monitor structural long-term displacements on the wall (SLDW) and structural vibrational displacements on the wall (SVDW) and then analyze their performance. Two novel methods are proposed in monitoring SVDW. Firstly, semi-generated measurements are designed to generate pseudo-environments with vibrations for the receiver. Therefore, additional instruments are not necessary to generate vibrations. Secondly, to further reduce the sheltering effect, a position-constrained PPP (PCPPP) model is developed. Formal performance analyses are presented in this study, and the results show that using the five-constellation PPP to monitor SLDW and SVDW in the horizontal direction is possible as long as the sheltering effect over the half sky of the receiver is not severe. In monitoring SVDW, the PCPPP model can perform better than the classical PPP model and be successful in the horizontal direction when the condition of elevation cutoff is given as high as 50°. For Asia-Pacific mid-low-latitude regions, the global positioning system (GPS) and BeiDou system (BDS) are important to maintain the availability of monitoring SVDW. Full article

The BeiDou Global Satellite Navigation System (BDS-3) broadcast newly developed B1C and B2a signals. To provide a better service for global users, the vertical phase center offset (PCO) and phase center variation (PCV) are estimated for the B1C/B2a ionospheric-free linear combination of the BDS-3 inclined geostationary orbit (IGSO) and medium earth orbit (MEO) satellites in this study. And considering the traditional PCC estimation method needs two Precise orbit determination (POD) processing, based on the correlation between PCO z-offset and PCV, the theoretical analysis and experimental comparison have been made to discuss whether the POD procedure for the PCO estimation can be omitted. The estimated z-offset time series revealed the inadequacy of the solar radiation pressure (SRP) model for the IGSO satellites and the MEO satellites with Pseudo Random Noise code (PRN) C45 and C46. The PCVraws estimated by the traditional method and the PCO estimation omitted method have the same characteristic. The final PCO z-offsets and PCVs calculated by the two schemes agreed very well with differences can be harmlessly ignored, which confirmed that the PCO estimation can be safely omitted to save computation time. The PCC model proposed in this study has been compared with the Test and Assessment Research Center of China Satellite Navigation Office (TARC/CSNO) released model, the qualities of the orbits and BDS-only precise point positioning (PPP) solutions of the new model both show improvements, except for the IGSO orbits. The analysis of the IGSO orbits further verifies the SRP model is not suitable for the IGSO satellites. Full article

Xiaomi Mi8 with a Broadcom BCM47755 chip, an Android smartphone that supports multi-constellation (GPS, GLONASS, Galileo, BeiDou, and QZSS) and dual-frequency (L1/E1 and L5/E5), was launched in May 2018. Unlike previously released smartphones, it was technically expected to provide robust precise positioning with a fast ambiguity resolution, which led many researchers to be overly optimistic about the applicability of high-accuracy techniques such as real-time kinematic (RTK) systems and precise point positioning (PPP) of smartphones. The global navigation satellite system (GNSS) raw measurement quality of Android smartphones is, however, inherently far lower than that of general GNSS receivers due to their structure, which accordingly makes it difficult for them to be realized. Considering inherent limitations of smartphones such as low-quality antenna, frequent cycle slips, and the duty cycle, a practical strategy including L5 measurements, pseudo-range corrections for L5, and a weighting method is proposed in this paper. The results show that the proposed methods of L5 differential GNSS (DGNSS) and Doppler-based filtering can guarantee a positioning accuracy of 1.75 m horizontally and 4.56 m vertically in an Android device, which is comparable to the performance of commercial low-cost receivers. Full article

The Chinese BeiDou-3 navigation satellite system (BDS-3) is capable of transmitting both old B1I, B3I signals and new B1C, B2a, B2b signals. Current BDS-3 precise orbits are generally calculated using a B1I/B3I combination considering overlap with the BeiDou-2 navigation satellite system (BDS-2). In this contribution, the observation quality of BDS-3 medium earth orbit (MEO) satellites and inclined geosynchronous orbit (IGSO) satellites are analyzed based on three aspects, i.e., carrier to noise ratio (C/N0), pseudo-range noise and pseudo-range multipath (MP). The C/N0 of the MEO satellite is 2~3 dB higher than that of the IGSO satellite at the same elevation angle. Meanwhile, the order of the Root Mean Square (RMS) values of both pseudo-range noise and MP is B1I < B1C < B3I < B2a ≈ B2b. Three kinds of combinations, i.e., B1CB2a, B1CB2b and B1IB3I, are selected for the BDS-3 precise orbit determination (POD) experiment. Orbits are assessed by the orbit-only signal-in-space range error (SISRE) computed between pairs of the three kinds of combinations in this contribution, CODE and GFZ final orbits. Orbit-only SISRE assessment shows that B1CB2a/CODE, B1CB2b/CODE, B1CB2a/GFZ and B1CB2b/GFZ are at the same level with CODE/GFZ, and the orbit-only SISRE is at the level of 5 cm for MEOs and 9 cm for IGSOs, respectively. Meanwhile, B1IB3I/CODE and B1IB3I/GFZ are about 1–2 cm worse. Inter-solution comparison between B1CB2a, B1CB2b and B1IB3I also indicate that B1CB2a and B1CB2b have good consistency, while B1IB3I shows poor performance. Satellite laser ranging (SLR) residuals indicate that the mean RMS is 3–4 cm for the four BDS-3 MEOs for CODE final orbit, GFZ final orbit, B1CB2a and B1CB2b combinations, while the mean RMS value for B1IB3I combination is a few millimeters worse, at approximately 4–5 cm. Full article

The radio determination service system (RDSS), a navigation and positioning system independently developed by China, features services such as short-message communication, position reporting, and international search and rescue. The L-band pseudo-range and phase data are the primary data sources in precise orbit determination (POD) for geostationary Earth orbit (GEO) satellite in the BeiDou system, especially in the orbit manoeuvre period. These data are the only data sources in the POD for GEOs. However, when the pseudo-range and phase data is abnormal due to unforeseen reasons, such as satellite hardware failure or monitoring receiver abnormalities, the data abnormality leads to orbit determination abnormalities or even failures for GEOs, then the service performance and availability of the RDSS system are greatly degraded. Therefore, a new POD method for GEOs based on BeiDou short-message communication ranging data has gained research attention to improve the service reliability of the BeiDou navigation satellite system (BDS)-3, realising the deep integration of communication and navigation services of the BDS. This problem has not been addressed so far. Therefore, in this study, a new POD method for GEO satellites is investigated using high-precision satellite laser ranging (SLR) data and RDSS data. The SLR data are used as the benchmark to calibrate the time delay value of RDSS equipment, and RDSS data are only used in the orbit determination process by fixing the corrected RDSS time delay value, and the satellite orbit parameters and dynamic parameters are solved. Experimental analysis is conducted using the measured SLR and RDSS data of the BDS, and the orbit accuracy in this paper is evaluated by the precise ephemeris of the Multi-GNSS pilot project (MGEX) and SLR data. The results show that the orbit accuracy in the orbital arc and the 2-h orbital prediction arc for GEOs are 6.01 m and 6.99 m, respectively, compared with the ephemeris of MGEX, and the short-arc orbit accuracy after 4 h of manoeuvring is 11.11 m. The orbit accuracy in the radial component by SLR data is 0.54 m. The required orbit accuracy for GEO satellites in the RDSS service of the BDS-3 is 15 m. The orbit accuracy achieved in this paper is superior to that of this technical index. This method expands the application field of the RDSS data and greatly enriches the POD method for GEOs. It can be adopted as a backup technology for the POD method for GEOs based on RNSS data, significantly improving the service reliability of the BeiDou RDSS service. Full article

Integrity is one of the key indicators used to characterize the performance of the global navigation satellite systems (GNSSs) and is closely related to user safety. In order to realize real-time global integrity monitoring, the BeiDou Global Navigation Satellite System (BDS-3) has realized the “satellite autonomous integrity monitoring” (SAIM) function in its satellites for the first time. BDS-3 SAIM has the monitoring functions of signal power, pseudo-range, satellite clock frequency and phase, but not the monitoring function of broadcast ephemeris. In this study, the long-term stability and distribution characteristics of BDS-3 SAIM monitoring data were analyzed by using the actual telemetry data for the first time. The results show that the SAIM monitoring data have good long-term stability and basically follow a normal distribution, which meets the design expectations. Meanwhile, in view of the fact that BDS-3 SAIM does not have the ability to independently monitor broadcast ephemerides, which may lead to the over-tolerance of BDS-3 to the probability risk of risks of integrity in the active space environment, a SAIM enhancement design for ephemeris monitoring is proposed, which integrates three relatively independent methods, with the ephemeris extrapolated from the previous cycle, and the ephemeris generated by autonomous orbit determination, inter-satellite link distance measurement data as reference data, respectively. The three methods are analyzed and verified. The results show that each of the three methods has advantages and disadvantages in terms of monitoring accuracy and resource dependence. The integration of the three methods can combine their complementary advantages and can also provide valuable as an important reference for engineering applications. Full article

With the development of urbanization, the environment is the key to the safety of residents’ life and health and the United Nations’ Sustainable Development Goals (SDGs). Urban environmental changes and microclimate problems have attracted widespread attention. For the SDGs, monitoring the urban microclimate more accurately and effectively and ensuring residents’ environmental health and safety is particularly important when designing applications that can replace the traditional fixed-point urban environment or pollution monitoring. Based on the BeiDou Navigation Satellite System platform, this paper proposes a fine-granularity urban microclimate monitoring method using wearable multi-source (PM_2.5, PM₁₀, and other air pollutants) sensors innovatively, which includes the satellite position function by adopting the satellite pseudo-range differential positioning technology, environmental data perception through the embedded system and wireless transmission, as well as the GIS data processing and analysis system. The wearable sensor acquires position and service information data through the satellite positioning system and acquires environmental parameters through integrated mobile multi-source sensors. The data are cached and wirelessly transmitted to the cloud server for digital processing. The urban microclimate is evaluated and visualized through algorithm and map API. Mobile monitoring can be flexibly applied to complex and diverse urban spaces, effectively realizing all-weather, all-directional, and accurate microclimate monitoring of urban environmental quality. Full article

China is promoting the construction of an integrated positioning, navigation, and timing (PNT) systems with the BeiDou Navigation Satellite System (BDS) as its core. To expand the positioning coverage area and improve the positioning performance by taking advantage of device-to-device (D2D) and self-organizing network (SON) technology, a BDS/SON integrated positioning system is proposed for the fifth-generation (5G) networking environment. This system relies on a combination of time-of-arrival (TOA) and BeiDou pseudo-range measurements to effectively supplement BeiDou signal blind spots, expand the positioning coverage area, and realize higher precision in continuous navigation and positioning. By establishing the system state model, and addressing the single-system positioning divergence and insufficient accuracy, a robust adaptive fading filtering (RAF) algorithm based on the prediction residual is proposed to suppress gross errors and filtering divergence in order to improve the stability and accuracy of the positioning results. Subsequently, a federated Kalman filtering (FKF) algorithm operating in fusion-feedback mode is developed to centrally process the positioning information of the combined system. Considering that the prediction error can reflect the magnitude of the model error, an adaptive information distribution coefficient is introduced to further improve the filtering performance. Actual measurement and significance test results show that by integrating BDS and SON positioning data, the proposed algorithm realizes robust, reliable, and continuous high precision location services with anti-interference capabilities and good universality. It is applicable in scenarios involving unmanned aerial vehicles (UAVs), autonomous driving, military, public safety and other contexts and can even realize indoor positioning and other regional positioning tasks. Full article

For the development of a global navigation satellite system (GNSS), the third generation of BeiDou Navigation Satellite System (BDS-3) achieved full constellation for worldwide service on 23 June 2020. The new signals, B1C and B2a of BDS-3, further enhance the compatibility and interoperability between different GNSSs. In this study, we first assessed the quality of all the signals in BDS-3/GPS/Galileo. Then, to achieve the interoperability among BDS-3/GPS/Galileo, the inter-system bias (ISB), which appears if an inter-system difference exists between two GNSSs, was estimated at overlapping frequencies. Finally, we used the estimated ISBs in real-time kinematic (RTK) positioning. The results show the higher quality of the overlapping frequency B2a/L5/E5a than B1C/L1/E1 in terms of pseudo range multipath. The ISBs are stable both in the short term for one day and in the long term for over a year, which fit a zero-mean normal distribution well when the identical type of receiver is applied. Thus, it is reasonable to ignore the ISBs in the inter-system differences. With the estimated ISBs, the inter-system double-difference RTK can be achieved, which is called a tightly combined model (TCM) RTK. Compared with the traditional intra-system double-difference RTK, which is called a loosely combined model (LCM) RTK, the TCM RTK can achieve a higher success rate (SR) in terms of ambiguity resolution and higher positioning accuracy. In addition, the higher the cutoff elevation angle set, the greater the promotion can be obtained in SR. Even with a cutoff elevation angle of 50°, the SR of TCM is over 80%. Thus, it is important to apply TCM RTK when the observation conditions are limited, such as in dense jungles or the urban canyons. Full article