Next Article in Journal
Broadband and Remote Electromagnetic Spectrum Sensing Based on Photonic Electric Field Sensor Chip
Previous Article in Journal
Dynamic Tunable Meta-Lens Based on a Single-Layer Metal Microstructure
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Susceptible Plasmonic Photonic Crystal Fiber Sensor with Elliptical Air Holes and External-Flat Gold-Coated Surface

by
Chung-Ting Chou Chao
1,
Muhammad Raziq Rahimi Kooh
2,
Yuan-Fong Chou Chau
2,* and
Roshan Thotagamuge
3,*
1
Department of Optoelectronics and Materials Technology, National Taiwan Ocean University, Keelung 20224, Taiwan
2
Centre for Advanced Material and Energy Sciences, Universiti Brunei Darussalam, Tungku Link, Gadong BE1410, Brunei
3
Department of Nano Science Technology, Faculty of Technology, Wayamba University of Sri Lanka, Kuliyapitiya 60200, Sri Lanka
*
Authors to whom correspondence should be addressed.
Photonics 2022, 9(12), 916; https://doi.org/10.3390/photonics9120916
Submission received: 5 November 2022 / Revised: 23 November 2022 / Accepted: 25 November 2022 / Published: 29 November 2022

Abstract

:
This paper proposes and analyzes a simple surface plasmon resonance (SPR)-based elliptical air hole photonic crystal fiber (PCF) sensor. The fiber structure comprises an analyte channel of the fiber surface coated with a gold layer on the flat surface and the fiber’s external surface. Numerical simulations are conducted using the finite element method (FEM) with an external sensing approach. We found that the thickness of plasmonic material (Au) is the most crucial factor that affects the full width at half maximum (FWHM) and confinement loss amplitude. We also demonstrated that the proposed elliptical air hole SPR-PCF is superior to circular air hole SPR-PCF in terms of confinement loss and FWHM. According to the wavelength interrogation technique, the simulation results show that the designed SPR-PCF sensor can attain a maximum sensitivity of 116,500 nm/RIU and a resolution of 8.58 × 10−7 RIU (RIU: refractive index unit) for the analyte RI of 1.395. We believe the proposed SPR-PCF sensor can be a potential candidate for biomolecular and biological analyte detection.

1. Introduction

The effects of surface plasmon resonance (SPR) on the surface of nanometals and dielectrics have attracted researchers’ attention because of the unique optic properties and the potential to overcome the diffraction limit in the nanoscale region [1,2,3,4]. SPR refers to the coherent oscillations of conduction electrons on the surface of a plasmonic material, resulting in localized SPRs and traveling surface plasmon polaritons (SPPs) [5,6]; these are popular optical devices for sensing and detecting applications [7,8,9].
SPR biosensing and gas detection using prism coupling was first proposed in 1983 [10]. In 1993, Jorgenson first presented the SPR optical fiber sensor and claimed that the designed sensor had the highest resolution, at 7.5 × 10−4 RIU [11]. Since then, many research groups have developed various optic fiber SPR sensors for chemical and biochemical sensing, such as Mach-Zehnder interferometer fiber [12], side-polishing technique fiber [13], graphene-deposited fiber [14], air-core hole SPR fiber [15], D-shaped optical fiber [16,17], photonic crystal fiber (PCF) [18,19], and Bragg grating SPR fiber [20,21] sensors. In the past decades, concerning the controllability of coupling between core-guided and SPP modes, attention has been focused on the PCF-based SPR sensor (SPR-PCF hereafter). Plasmonic materials and PCF technology are combined to construct an SPR-PCF–based sensor, providing design flexibility and minor size requirements [22,23,24,25].
The mechanism of an SPR-PCF sensor operates using transient electromagnetic (EM) wave interaction with the plasmonic materials (e.g., gold (Au), silver (Ag), copper (Cu), etc.). The EM waves can penetrate through the fiber cladding region and generate an evanescent EM wave. This then excites the free electrons of the nanometal surface and produces an SPP wave at the interface of the metal and dielectric [26,27,28,29,30]. At a resonance wavelength, the real part of the effective RI of the core-guided mode and SPP mode is completely phase-matched. It generates a pointy confinement loss peak, which can inspect the unknown sample/analyte [31,32,33].
The SPR-PCF–based sensors can categorize internal and external sensing schemes [26,34,35]. For the internal sensing approach, it can be challenging to process metal coating and liquid dropping in the inside structure of fiber [36,37]. The external sensing method can easily detect the unknown analyte by infiltrating the analyte through the metal surface. Therefore, the external sensing method is well known, since the practical realization is easy and possible [17,38].
The external sensing method for SPR-PCF–based sensors has become a central topic of interest in recent years. Kiroriwal et al. proposed an SPR-PCF refractive index (RI) sensor with 36 air holes and obtained a wavelength sensitivity of 8000 nm/RIU in the RI range of 1.36–1.40 [39]. Popescu et al. demonstrated a honeycomb SPR-PCF sensor with two complementary supermodes [23]. They claimed that the sensitivity can increase from 1000 nm/RIU to 4500 nm/RIU. Shakya et al. investigated a tetra-core–based SPR-PCF sensor containing three different dimensions of air holes [40] and obtained a wavelength sensitivity of 5000 nm/RIU. Kumar et al. verified a D-shape SPR-PCF sensor using Mxene/Au material thin film. They obtained a wavelength sensitivity of 7000 nm/RIU and 13,000 nm/RIU for the Mxene layer thicknesses of 14 nm and 27 nm, respectively [41]. Paul et al. presented a dual-core SPR-PCF sensor [42] and obtained a maximum wavelength sensitivity of 25,000 nm/RIU, with an analyte RI of 1.38. Tong et al. displayed a three-core SPR-PCF sensor with an outer layer of Au film [24]. Introducing the multi-core in the fiber structure can improve the sensor performance. Zhao et al. illustrated the photonic bandgap fiber and the Bragg fiber with various forms, including fuse-tapered fiber structure, D-type fiber structure, and cladding-off fiber structure [43]. They fabricated the proposed structures and confirmed that the designed devices have the merits of high sensitivity and resolution.
All of the abovementioned SPR-PCF sensors have high wavelength sensitivity. However, the proposed SPR-PCF structures possess many air holes in the PCF cladding (more than 20), which results in a complex fabrication. In this work, we propose a simple SPR-PCF sensor structure with eight elliptical air holes and a fiber surface coated with an Au layer on the polished surface and external fiber surface. The proposed SPR-PCF sensor can detect an analyte externally. We investigate the sensing performance of the proposed device employing the finite element method (FEM)-based COMSOL Multiphysics software. We consider the effects of RI surrounding the fiber structure, the thickness of Au film, and the ratio of semi-minor and semi-major axes of elliptical air holes to ensure accuracy. The results offer an experimental basis and theoretical guidance for designing high-sensitivity SPR-PCF sensors.
This paper organizes as follows: Section 1 is the introduction. Section 2 presents the numerical modeling method and basic formulas. The optimization of the structural parameters is discussed in detail in Section 3. Section 4 concerns the application as a RI SPR-PCF sensor and compares this work with similarly reported studies. Finally, the results are summarized in the concluding section.

2. Numerical Modeling Method and Basic Formulas

For the fiber structure’s simplicity, the number of air holes chosen is as low as possible. We decided on eight elliptical holes with three different sizes in our design, based on the FEM simulations. Figure 1 depicts the cross-section of the designed SPR-PCF–based sensor, with eight elliptic air holes in the PCF’s cladding. The semi-major axis of different sizes of elliptic air-holes are a1y, a2y, and a3y, and their coordinates are (±d1, 0) for the biggest ones, (0, ±d2) for the middle size ones, and (±d3, ±d2) for the smallest size ones, correspondingly. The d1, d2, and d3 are fixed at 1.8 µm, 1.5 µm, and 1.5 µm throughout this work. The purpose of using diverse sizes of elliptical air holes is to generate a higher birefringence [44,45,46,47]. Their sensing performance is superior to a circular one. The ratio of semi-minor and semi-major axes (i.e., ellipticity, e) is e = a1x/a1y = a2x/a2y = a3x/a3y. The distance between the top elliptical air hole and the polished surface is h.
The Au film is covered on the top cutting flat plane and the outer surface of the SPR-PCF sensor with a thickness of tAu, which facilitates the detection ability of the proposed PCF sensor. The analyte layer with a thickness of 0.5 μm is located on the Au layer’s outer surface to sense the surrounding medium. The maximum mesh element sizes are set as the corresponding thickness layer in the Au layer. The analyte surrounds the entire SPR-PCF structure and is a liquid with different RIs in RI sensing. A change in the resonant wavelength (λres) occurs when the analyte’s RI changes, allowing us to detect changes in RI. We numerically investigated the proposed PCF sensor using the full vectorial FEM-based software COMSOL Multiphysics to optimize structural parameters and determine the sensor sensitivity and selectivity. A circular perfectly matched layer (PML) boundary condition with a thickness of 0.7 μm and a scattering boundary condition (SBC) were added to the outer computational domain to absorb the artificial back-reflection at the boundaries during the simulation. In the FEM simulations, we utilized the finer meshing elements of 17,956 domain elements and 1453 boundary elements.
The core and cladding regions are fused silica with a diameter of the silica layer of 6 µm. The RI of silica is obtained from the Sellmeier Equation [48]:
n 2 ( λ ) = 1 + B 1 λ 2 λ 2 C 1 + B 2 λ 2 λ 2 C 2 + B 3 λ 2 λ 2 C 3
where n and λ denote the wavelength-dependent RI and wavelength (in µm); B1, B2, B3, C1, C2, and C3 are the constant values of the Sellmeier Equation, which are listed in Table 1.
The SPR-PCF sensing performance closely relies on the noble nanometal. Ag and Au are commonly utilized for plasmonic sensing applications. The Ag can offer a sharper SPR peak, but it possesses the drawbacks of being chemically unstable and easily oxidized [13]. Therefore, we used Au as the plasmonic material since it is chemically stable in an aqueous environment and displays a sizeable λres shift compared with other novel nanometals. The permittivity of Au is wavelength dependent and can be obtained from the Drude-Lorentz model [49,50]:
ε A u = ε ω 2 D ω ( ω + j γ D ) Δ ε Γ L 2 j Γ L ω + ( ω 2 Γ L 2 )
where the value of ε (the permittivity of high frequency), ω (angular frequency), ωD (plasmon resonance frequency), γD (damping frequency), ΩL (oscillation strength of the Lorentz oscillators), and ΓL/2π (spectrum width) are listed in Table 2.
The confinement loss (CL) spectrum of the core-guided mode can evaluate the sensing performance, and the CL of the core-guided mode can be described as follows [51,52]:
α 8.686 × 2 π λ × I m [ n e f f ] × 10 4 d B c m
where Im (neff) is an imaginary part of the effective RI of the core-guided mode.
Sensitivity is obtained by
S A ( λ ) [ n m / R I U ] = Δ λ p e a k / Δ n a n a
where Δλpeak is the change in peak wavelength, and Δ n a n a denotes the shift in two successive RIs.
Sensor resolution can be expressed by [28]
R [ R I U ] = n a n a × Δ λ m i n Δ λ p e a k
where Δ λ m i n is the wavelength resolution.
L indicates the length of the sensor in cm (i.e., how long the sensor is for the specific RI), which can be computed as follows [29]:
L = 1 α ( λ , n a n a )
where α ( λ , n a n a ) is the overall CL for a particular wavelength.
The proposed SPR-PCF sensor can be fabricated with nanofabrication technology. To manufacture the proposed SPR-PCF sensor, PCF may utilize stack and drawing, extrusion, or capillary stacking techniques to make the prefabricated rod [53]. To adjust the air holes’ size and obtain the elliptical air hole, the thin walls of the air holes are squeezed by controlling the pressure to obtain the ellipse [54]. In this manner, the proposed SPR-PCF can be fabricated successfully. Au can be deposited on the surface of the SPR-PCF by customized vapor deposition (CVD) or atomic layer deposition (ALD) [55] and exterior vapor deposition (EVD) [56]. However, this work focuses on something other than the fabrication procedures. As an alternative, several potential articles that investigated in-depth fabrication of the elliptical air holes in PCF are suggested [57,58,59].

3. Optimization of the Structural Parameters

The initial values of the geometrical parameters of the designed SPR-PCF structure are specified in Table 3.
The real parts of the effective RIs of the core-guided mode (red dashed line) and SPP modes (black dashed line) and the CL spectrum of the core-guided mode (blue curve) in the proposed SPR-PCF sensor are shown in Figure 2, where the geometrical parameters of the PCF are as specified in Table 3. Figure 3a,b are the E-field distributions of the SPP and core-guided modes (y-polarization) at λpeak = 694 nm. In Figure 2, the λpeak happens when the line of effective RIs of the core-guided mode overlaps with a high-order SPP mode. In this situation, the energy can transfer from the core-guided mode to the SPP mode, resulting in the CL peak of 79.92 dB/cm, which can be acquired at λpeak = 694 nm for nana = 1.38. Note that the SPR effect of SPP mode (see Figure 3a) on the top-flat surface of Au film is higher than that of the side-throw surface.
The geometrical parameters, such as the Au thickness (tAu), semi-major axes (a1y, a2y, and a3y), ellipticity (e), and the distance between the top elliptical air hole and the polished surface (h), are the pivotal factors that can effectively affect the sensing performance of the designed device. In the following simulations, we change one of the geometrical parameters while fixing the other parameters specified in Table 3.
The thickness of coated plasmonic material, tAu, has a potential impact on the CL of the SPR-PCF sensor. The tAu strongly influences the λpeak shift, which can be used in measuring the testing medium interaction with the surface of the Au layer. When the tAu increases from 10 to 50 nm, which is comparable with the skin depth of the Au in the visible wavelength range [60]. Figure 4 shows the CL spectra of the core-guided mode for various tAu, ranging in 10 nm ≤ tAu ≤ 50 nm. As seen, the CL peak redshifts with the increase of tAu from λpeak = 498 nm to λpeak = 821 nm when 10 nm ≤ tAu ≤ 50 nm. When the tAu is relatively thin (e.g., tAu = 10, 15, 20, and 25 nm), the energy of the evanescent EM wave on the Au surface is also weak. When the tAu increases, the coupling effect between the core-guided mode and the SPP mode can be enhanced and reach the highest value of λpeak = 694 nm when tAu = 30 nm. The loss increases from 3.18 dB/cm to 79.92 dB/cm when tAu changes from 10 nm to 30 nm. A thicker tAu (e.g., tAu = 35, 40, and 50 nm) mitigates the coupling effect between the core-guided mode and the SPP mode due to the shielding of the EM wave from the core region to the outer Au surface, leading to the decrease of the CL peak. As a result, the CL peak drops from 79.92 dB/cm to 41.02 dB/cm when tAu is 30 nm ≤ tAu ≤ 50 nm. From Figure 4, we can conclude that the tAu is the most crucial factor that affects the full width at half maximum (FWHM) and the amplitude of the CL peak. One can explain the matching impedance and SPR resonance conditions between the core region and the Au surface. The variation of tAu results in impedance when the resonance condition of the fiber is satisfied.
Meanwhile, λpeak should increase to guarantee the impedance between the fiber core region and Au surface when the resonance condition of the fiber is changed by tAu. It is noticeable that there is a sharp transition in the CL value when tAu is increased from 25 to 30 nm. The reason can be understood from the resonance condition between the core-guided and SPP modes at various tAu. This indicates that the highest energy exchange between guided and SPP modes occurs when tAu = 30 nm.
The size of the major axis in the elliptical air holes is essential in affecting the CL. Based on the FEM simulations, the major axis of the elliptical air holes, i.e., a1y, a2y, and a3y, can significantly affect the coupling effect between the core-guided mode and SPP mode. Figure 5, Figure 6 and Figure 7 display the CL versus wavelength for a1y = (0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.9) µm, a2y = (0.68, 0.70, 0.72, 0.74, 0.76, 0.78) µm, and a3y = (0.35, 0.36, 0.37, 0.38, 0.39, 0.40, 0.41, 0.42) µm, respectively. The increase in CL indicates the nature of the coupling effect, and a higher CL can facilitate the energy transformation from the core-guided to the SPP mode. As observed in Figure 5, the CL peak occurs at λpeak = 695 nm for all cases except that of a1y = 0.6 μm. The case of a1y = 0.65 μm shows the highest CL peak of 261.01 dB/cm but reveals a larger FWHM of 30 nm. In contrast, a smaller CL peak for the cases of a1y = 0.75, 0.80, 0.85, and 0.9 μm are 111.33, 79.92, 63.49, and 55.97 dB/cm, correspondingly. It is noticeable that the CL spectrum curve of a1y = 0.60 μm displays a broad range of peak values. A larger FWHM (around 60 nm) negatively influences the sensing performance. Therefore, the best result is a1y = 0.7 μm based on a CL value of 166.69 dB/cm and FWHM width of 20 nm.
In Figure 6, the CL peak redshifts and has a higher value with the increasing a2y range being a2y = (0.68, 0.70, 0.72, 0.74, 0.76, 0.78) µm. These values of a2y are available in the proposed SPR-PCF and imply that we can manipulate the desired operation wavelength by varying the a2y. In this case, we choose a2y = 0.78 µm as an optimal value due to its higher CL value of 93.67 dB/cm and an acceptable FWHM of 20 nm. It can be seen in Figure 7 that the CL peaks exhibit a slight blueshift from λpeak = 697 nm to λpeak =693 nm, and the CL values drop from 159.82 dB/cm to 59.01 dB/cm when a3y varies in the range of a3y = (0.35, 0.36, 0.37, 0.38, 0.39, 0.40, 0.41, 0.42) µm. The smaller a3y experiences a higher CL value because the scaled-down a3y facilitates driving the EM wave away from the PCF core region to the PCF surface. Note that in the structure optimization process, the change of a2y will cause the CL peak to show a regular λpeak shift and an increased CL value, while a1y and a3y only affect the CL value. The CL value depends on the contribution of the coupling effect from the core-guided mode to the SPP mode, and the λpeak shift is related to the resonance condition and the variation of Im(neff) in the SPR-PCF. As seen in Figure 6, one can obtain the desired working wavelength by changing the size of a2y.
The ellipticity of elliptical air holes can remarkably affect the light energy coupling between the core-guided and SPP mode [19]. Figure 8 displays the CL versus wavelength for ellipticity e = 0.4, 0.5, 0.55, 0.60, 0.65, 0.70, 0.75, and 1.00. It is evident in Figure 8 that the CL redshifts from 688, 691, 693, 694, 698, 702, to 703 nm when the ellipticity increases from 0.4 to 1.00, while the intensity of CL and the width of FWHM decreases from (CL, FWHM) = (235.66 dB/cm, 25 nm), (137.14 dB/cm, 22 nm), (104.80 dB/cm, 20 nm), (79.92 dB/cm, 20 nm), (60.39 dB/cm, 19 nm), (44.99 dB/cm, 18 nm), (32.46 dB/cm, 17 nm) to (2.73 dB/cm, 60 nm). Compared to the elliptical air-hole cases, the circular air-hole case (i.e., e = 1.00) shows a lower amplitude of CL peak and a broadened FWHM. These results demonstrate that the elliptical air holes in the designed SPR-PCF sensor are superior to the case of circular air holes in terms of the CL and FWHM. The smaller ellipticity can facilitate the energy transformation from the core-guided to the SPP mode. However, the smaller ellipticity will exhibit a larger FWHM, as observed in the dashed arrow lines in Figure 9. As a result, we choose the optimal value of e = 0.55 in the viewpoint of the CL value and the width of FWHM (CL = 104.80 dB/cm, FWHM = 19 nm).
Subsequently, we inspected the distance between the top elliptical air hole and the flat surface, h. As illustrated in Figure 9, the CL amplitude decreases with the increasing h. When h increases from 0 to 0.6 µm in the step of 0.1 µm, there is a slight blueshift from λpeak = 695 nm to λpeak = 692 nm, and the CL amplitude decreases from 110.76 dB/cm to 69.29 dB/cm. According to the CL spectrum, as shown in Figure 9, the available range of h in the proposed structure can be selected as 0 µm ≤ h ≤ 0.6 µm. The Au-coated flat surface can facilitate the coupling effect between the SPP wave and analyte, and the length of the Au-coated flat surface depends on different sizes of h value. Note that if h = 0 µm, the proposed SPR-PCF structure exhibits a circular outer surface (i.e., no flat surface), the CL amplitude can reach the highest value but shows a bigger FWHM (25 nm) and an unsmooth CL curve range of 640 nm ≤ λ ≤ 680 nm. As a result, we selected h = 0.4 m for the following simulation in terms of a smooth CL curve and a smaller FWHM (18 nm).

4. Application as a Refractive Index SPR-PCF Sensor

Finally, the application of the RI sensor based on the optimized designed structure was inspected. Table 4 shows the optimal geometrical parameters of the designed SPR-PCF based on the optimization of the structural parameters mentioned above.
To achieve precise RI detection, we examined the RI of the analyte, nana = 1.31, 1.32, 1.33, 1.34, 1.35, 1.36, 1.37, 1.38, 1.39, 1.391, 1.392, 1.393 and 1.395, as the surrounding media. Figure 10a,b present the CL spectra of the core-guided mode for the different RIs of analytes (nana). Figure 10a illustrates nana = 1.31–1.36 in the step of 0.01, and Figure 10b exhibits nana =1.37, 1.38, 1.39, 1.391, 1.392, 1.393, and 1.395. Note that the CL spectrum increases precipitously when the RI is in the range of 1.39–1.395 due to the abrupt change of resonance condition between the core-guided mode and SPP mode. These results are similar to other studies (see [61,62,63]). We can explain this phenomenon in that the CL is proportional to Im(neff). The maximum nana value of 1.395 is chosen since there is no valid CL peak in the proposed structure when nana 1.395, i.e., for target analyte RI 1.3950, the λpeak was not obtained, and consequently the overall sensitivity reduces. As observed in Figure 10a,b, all curves experience a redshift with an increase in nana. The positions of the CL peaks change slowly for a smaller value of nana; e.g., CL peaks vary from 25 dB/cm to 132 dB/cm as nana increases from 1.31 to 1.36 in the step of 0.01. Meanwhile, the positions of the CL peaks change rapidly with a higher value of nana, e.g., CL peaks vary from 252 dB/cm to 3122 dB/cm as nana rises from 1.37 1.38, 1.39, 1.391, 1.392, 1.393 to 1.395. Note that the CL spectrum displays a significant redshift when nana 1.37 (see Figure 10b). Remarkably, the designed SPR-PCF is susceptible to minimal variations in RI in the order of ±0.001. One of the critical findings of the proposed SPR-PCF sensor is that it can detect the RI of the analyte higher than that of the fiber background.
Various RIs can be obtained in the wavelength interrogation mode by calculating the Δλpeak. Figure 11 plots λpeak and CL spectra of the core-guided mode for different analytes (nana) ranging from 1.31–1.3950. The RI sensitivity S can be attained from Equation (4). As can be seen in Figure 11, the RI sensitivity S of the two adjacent points is SAB = 116,500 nm/RIU, SBC = 16,000 nm/RIU, SCD = 18,000 nm/RIU, SDE = 16,000 nm/RIU, SEF = 8800 nm/RIU, SFG = 5100 nm/RIU, SGH = 3100 nm/RIU, SHI = 2400 nm/RIU, SIJ = 1700 nm/RIU, SJK = 1300 nm/RIU, SKLJ = 1100 nm/RIU, and SLM = 1100 nm/RIU, corresponding to the wavelength interval of 550 nm to 1200 nm. The proposed SPR-PCF sensor’s RI resolution can be obtained from Equation (5). The Δnana and Δλpeak in SAB shown in Figure 11 are Δnana = 0.002 and Δλpeak = 233 nm, respectively. We assume Δλmin = 0.1 nm. Consequently, the minimum resolution can be obtained: 8.58 × 10−7 RIU.
Concerning the performance of the proposed SPR-PCF, Table 5 contains the required data from Figure 11, including nana, CL (dB/cm), λpeak (nm), sensor length (cm, based on Equation (6)), sensitivity (nm/RIU), and resolution (RIU), concerning the variation of RIs in the interval of 1.31–1.395.
Table 6 summarizes the performance analysis comparison (including published year, RI range, wavelength range, maximum wavelength sensitivity, and sensor resolution) between the proposed SPR-PCF sensor and previously reported sensors. Table 6 shows that our proposed SPR-PCF sensor reveals better sensing performance with higher sensitivity and better resolution.

5. Conclusions

In summary, we designed a simple and high-sensitivity elliptical air hole SPR-PCF–based sensor where Au is deposited as a plasmonic material to deploy an external sensing approach. We used FEM-based COMSOL Multiphysics software to simulate the sensor and further characterize the performance. Through FEM simulations, the influences of RI on structural parameters of the SPR-PCF were discussed and calculated. We found that the thickness of plasmonic material (Au) is the most important factor affecting the FWHM and CL amplitude. We also demonstrated that the proposed elliptical air hole SPR-PCF is superior to the circular air hole SPR-PCF based on CL and FWHM. Under the optimized structural parameters, the proposed SPR-PCF sensor verifies the highest wavelength sensitivity of 116,500 nm/RIU with an 8.58 × 10−7 RIU sensing solution for the analyte RI of 1.395. The device can detect highly active chemical and biological liquid samples because of its excellent sensing performance.

Author Contributions

Conceptualization, investigation, C.-T.C.C.; methodology, software, and data curation, M.R.R.K.; validation, formal analysis, resources R.T.; writing—original draft preparation, C.-T.C.C.; writing—review and editing, Y.-F.C.C. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the University Research Grant of Universiti Brunei Darussalam, grant number UBD/RSCH/1.9/FICBF(b)/2022/018.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

The authors thankfully acknowledge the financial support rendered by the Universiti Brunei Darussalam.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Chau, Y.-F.; Yeh, H.-H.; Tsai, D. Surface plasmon resonances effects on different patterns of solid-silver and silver-shell nanocylindrical pairs. J. Electromagn. Waves Appl. 2010, 24, 1005–1014. [Google Scholar] [CrossRef]
  2. Deng, Y.; Cao, G.; Yang, H.; Zhou, X.; Wu, Y. Dynamic Control of Double Plasmon-Induced Transparencies in Aperture-Coupled Waveguide-Cavity System. Plasmonics 2018, 13, 345–352. [Google Scholar] [CrossRef]
  3. Deng, Y.; Cao, G.; Wu, Y.; Zhou, X.; Liao, W. Theoretical Description of Dynamic Transmission Characteristics in MDM Waveguide Aperture-Side-Coupled with Ring Cavity. Plasmonics 2015, 10, 1537–1543. [Google Scholar] [CrossRef]
  4. Lin, C.-T.; Chang, M.-N.; Huang, H.J.; Chen, C.-H.; Sun, R.-J.; Liao, B.-H.; Chau, Y.-F.C.; Hsiao, C.-N.; Shiao, M.-H.; Tseng, F.-G. Rapid fabrication of three-dimensional gold dendritic nanoforests for visible light-enhanced methanol oxidation. Electrochim. Acta 2016, 192, 15–21. [Google Scholar] [CrossRef]
  5. Hsieh, L.-Z.; Chau, Y.-F.C.; Lim, C.M.; Lin, M.-H.; Huang, H.J.; Lin, C.-T.; Syafi’ie, I.M.N. Metal nano-particles sizing by thermal annealing for the enhancement of surface plasmon effects in thin-film solar cells application. Opt. Commun. 2016, 370, 85–90. [Google Scholar] [CrossRef]
  6. Chau, Y.-F.; Jiang, Z.-H.; Li, H.-Y.; Lin, G.-M.; Wu, F.-L.; Lin, W.-H. Localized resonance of composite core-shell nanospheres, nanobars and nanospherical chains. Prog. Electromagn. Res. B 2011, 28, 183–199. [Google Scholar] [CrossRef] [Green Version]
  7. Divya, J.; Selvendran, S.; Raja, A.S.; Sivasubramanian, A. Surface plasmon based plasmonic sensors: A review on their past, present and future. Biosens. Bioelectron. X 2022, 11, 100175. [Google Scholar] [CrossRef]
  8. Shangguan, Q.; Chen, Z.; Yang, H.; Cheng, S.; Yang, W.; Yi, Z.; Wu, X.; Wang, S.; Yi, Y.; Wu, P. Design of Ultra-Narrow Band Graphene Refractive Index Sensor. Sensors 2022, 22, 6483. [Google Scholar] [CrossRef]
  9. Chen, H.; Chen, Z.; Yang, H.; Wen, L.; Yi, Z.; Zhou, Z.; Dai, B.; Zhang, J.; Wu, X.; Wu, P. Multi-mode surface plasmon resonance absorber based on dart-type single-layer graphene. RSC Adv. 2022, 12, 7821–7829. [Google Scholar] [CrossRef]
  10. Liedberg, B.; Nylander, C.I.; Lunström, I. Surface plasmon resonance for gas detection and biosensing. Sens. Actuators B Chem. 1983, 4, 299–304. [Google Scholar] [CrossRef]
  11. Jorgenson, R.C.; Yee, S.S. A fiber-optic chemical sensor based on surface plasmon resonance. Sens. Actuators B Chem. 1993, 12, 213–220. [Google Scholar] [CrossRef]
  12. Nazeri, K.; Bradley, C. The effect of photonic crystal fibre structure on the performance of Mach-Zehnder interferometer fibre optic gas sensors. Opt. Fiber Technol. 2020, 58, 102294. [Google Scholar] [CrossRef]
  13. Kim, H.; Kim, J.; Paek, U.-C.; Lee, B.H.; Kim, K.T. Tunable photonic crystal fiber coupler based on a side-polishing technique. Opt. Lett. 2004, 29, 1194–1196. [Google Scholar] [CrossRef]
  14. Tan, Y.C.; Tou, Z.Q.; Chow, K.K.; Chan, C.C. Graphene-deposited photonic crystal fibers for continuous refractive index sensing applications. Opt. Express 2015, 23, 31286–31294. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  15. Paul, A.K.; Habib, S.; Hai, N.H.; Razzak, S.A. An air-core photonic crystal fiber based plasmonic sensor for high refractive index sensing. Opt. Commun. 2020, 464, 125556. [Google Scholar] [CrossRef]
  16. Gupta, A.; Singh, H.; Singh, A.; Singh, R.K.; Tiwari, A. D-Shaped Photonic Crystal Fiber–Based Surface Plasmon Resonance Biosensors with Spatially Distributed Bimetallic Layers. Plasmonics 2020, 15, 1323–1330. [Google Scholar] [CrossRef]
  17. Han, B.; Zhang, Y.-N.; Siyu, E.; Wang, X.; Yang, D.; Wang, T.; Lu, K.; Wang, F. Simultaneous measurement of temperature and strain based on dual SPR effect in PCF. Opt. Laser Technol. 2019, 113, 46–51. [Google Scholar] [CrossRef]
  18. Xie, Q.; Chen, Y.; Li, X.; Yin, Z.; Wang, L.; Geng, Y.; Hong, X. Characteristics of D-shaped photonic crystal fiber surface plasmon resonance sensors with different side-polished lengths. Appl. Opt. 2017, 56, 1550–1555. [Google Scholar] [CrossRef]
  19. Chau, Y.-F.; Liu, C.-Y.; Yeh, H.-H.; Tsai, D.P. A comparative study of high birefringence and low confinement loss photonic crystal fiber employing elliptical air holes in fiber cladding with tetragonal lattice. Prog. Electromagn. Res. B 2010, 22, 39–52. [Google Scholar] [CrossRef] [Green Version]
  20. Wu, T.; Shao, Y.; Wang, Y.; Cao, S.; Cao, W.; Zhang, F.; Liao, C.; He, J.; Huang, Y.; Hou, M.; et al. Surface plasmon resonance biosensor based on gold-coated side-polished hexagonal structure photonic crystal fiber. Opt. Express 2017, 25, 20313–20322. [Google Scholar] [CrossRef] [PubMed]
  21. Xiang, H.; Jiang, Y. Fiber Bragg grating inscription in multi-core photonic crystal fiber by femtosecond laser. Optik 2018, 171, 9–14. [Google Scholar] [CrossRef]
  22. Haider, F.; Aoni, R.A.; Ahmed, R.; Miroshnichenko, A.E. Highly amplitude-sensitive photonic-crystal-fiber-based plasmonic sensor. J. Opt. Soc. Am. B 2018, 35, 2816–2821. [Google Scholar] [CrossRef]
  23. Popescu, V.; Sharma, A.K.; Marques, C. Resonant interaction between a core mode and two complementary supermodes in a honeycomb PCF reflector-based SPR sensor. Optik 2021, 227, 166121. [Google Scholar] [CrossRef]
  24. Tong, K.; Wang, F.; Wang, M.; Dang, P.; Wang, Y. Three-core photonic crystal fiber surface plasmon resonance sensor. Opt. Fiber Technol. 2018, 46, 306–310. [Google Scholar] [CrossRef]
  25. Wang, D.; Yi, Z.; Ma, G.; Dai, B.; Yang, J.; Zhang, J.; Yu, Y.; Liu, C.; Wu, X.; Bian, Q. Two-channel photonic crystal fiber based on surface plasmon resonance for magnetic field and temperature dual-parameter sensing. Phys. Chem. Chem. Phys. 2022, 24, 21233–21241. [Google Scholar] [CrossRef]
  26. Yan, X.; Wang, Y.; Cheng, T.; Li, S. Photonic Crystal Fiber SPR Liquid Sensor Based on Elliptical Detective Channel. Micromachines 2021, 12, 408. [Google Scholar] [CrossRef] [PubMed]
  27. Islam, M.R.; Iftekher, A.N.M.; Hasan, K.R.; Nayen, J.; Islam, S.B.; Hossain, A.; Mustafa, Z.; Tahsin, T. Design and numerical analysis of a gold-coated photonic crystal fiber based refractive index sensor. Opt. Quantum Electron. 2021, 53, 112. [Google Scholar] [CrossRef]
  28. Gao, D.; Guan, C.; Wen, Y.; Zhong, X.; Yuan, L. Multi-hole fiber based surface plasmon resonance sensor operated at near-infrared wavelengths. Opt. Commun. 2014, 313, 94–98. [Google Scholar] [CrossRef]
  29. Han, H.; Hou, D.; Luan, N.; Bai, Z.; Song, L.; Liu, J.; Hu, Y. Surface Plasmon Resonance Sensor Based on Dual-Side Polished Microstructured Optical Fiber with Dual-Core. Sensors 2020, 20, 3911. [Google Scholar] [CrossRef]
  30. Wang, Q.; Zhang, X.; Yan, X.; Wang, F.; Cheng, T. Design of a Surface Plasmon Resonance Temperature Sensor with Multi-Wavebands Based on Conjoined-Tubular Anti-Resonance Fiber. Photonics 2021, 8, 231. [Google Scholar] [CrossRef]
  31. Wang, Y.; Huang, Q.; Zhu, W.; Yang, M.; Lewis, E. Novel optical fiber SPR temperature sensor based on MMF-PCF-MMF structure and gold-PDMS film: Erratum. Opt. Express 2019, 27, 10813. [Google Scholar] [CrossRef] [PubMed]
  32. Rafi, H.N.; Kaysir, R.; Islam, J. Air-hole attributed performance of photonic crystal fiber-based SPR sensors. Sens. Bio-Sens. Res. 2020, 29, 100364. [Google Scholar] [CrossRef]
  33. Rahman, K.M.; Alam, M.S.; Islam, M.A. Highly sensitive gold-coated surface plasmon resonance photonic crystal fiber sensor in near-infrared region. Results Opt. 2022, 7, 100223. [Google Scholar] [CrossRef]
  34. Zhou, X.; Cheng, T.; Li, S.; Suzuki, T.; Ohishi, Y. Practical sensing approach based on surface plasmon resonance in a photonic crystal fiber. OSA Contin. 2018, 1, 1332–1340. [Google Scholar] [CrossRef]
  35. Kamrunnahar, Q.M.; Haider, F.; Aoni, R.A.; Mou, J.R.; Shifa, S.; Begum, F.; Abdul-Rashid, H.A.; Ahmed, R. Plasmonic Micro-Channel Assisted Photonic Crystal Fiber Based Highly Sensitive Sensor for Multi-Analyte Detection. Nanomaterials 2022, 12, 1444. [Google Scholar] [CrossRef] [PubMed]
  36. Liu, Q.; Li, S.; Gao, X. Highly sensitive plasmonics temperature sensor based on photonic crystal fiber with a liquid core. Opt. Commun. 2018, 427, 622–627. [Google Scholar] [CrossRef]
  37. Liang, H.; Shen, T.; Feng, Y.; Xia, Z.; Liu, H. A Surface Plasmon Resonance Temperature Sensing Unit Based on a Graphene Oxide Composite Photonic Crystal Fiber. IEEE Photonics J. 2020, 12, 1–11. [Google Scholar] [CrossRef]
  38. Shakya, A.K.; Singh, S. Design of novel Penta core PCF SPR RI sensor based on fusion of IMD and EMD techniques for analysis of water and transformer oil. Measurement 2022, 188, 110513. [Google Scholar] [CrossRef]
  39. Kiroriwal, M.; Singal, P. Design and analysis of highly sensitive solid core gold-coated hexagonal photonic crystal fiber sensor based on surface plasmon resonance. J. Nanophotonics 2021, 15, 026008. [Google Scholar] [CrossRef]
  40. Shakya, A.K.; Singh, S. Design of dual polarized tetra core PCF based plasmonic RI sensor for visible-IR spectrum. Opt. Commun. 2021, 478, 126372. [Google Scholar] [CrossRef]
  41. Kumar, A.; Verma, P.; Jindal, P. Surface plasmon resonance biosensor based on a D-shaped photonic crystal fiber using Ti3C2Tx MXene material. Opt. Mater. 2022, 128, 112397. [Google Scholar] [CrossRef]
  42. Paul, A.K.; Sarkar, A.K.; Islam, H.; Morshed, M. Dual core photonic crystal fiber based surface plasmon resonance biosensor. Optik 2018, 170, 400–408. [Google Scholar] [CrossRef]
  43. Zhao, Y.; Deng, Z.-Q.; Li, J. Photonic crystal fiber based surface plasmon resonance chemical sensors. Sens. Actuators B Chem. 2014, 202, 557–567. [Google Scholar] [CrossRef]
  44. Yasli, A.; Ademgil, H. Effect of plasmonic materials on photonic crystal fiber based surface plasmon resonance sensors. Mod. Phys. Lett. B 2019, 33, 1950157. [Google Scholar] [CrossRef]
  45. Steel, M.J.; Osgood, R.M. Elliptical-hole photonic crystal fibers. Opt. Lett. 2001, 26, 229–231. [Google Scholar] [CrossRef] [PubMed]
  46. Sun, Y.-S.; Chau, Y.-F.; Yeh, H.-H.; Tsai, D.P. Highly birefringent index-guiding photonic crystal fiber with squeezed differently sized air-holes in cladding. Jpn. J. Appl. Phys. 2008, 47, 3755. [Google Scholar] [CrossRef] [Green Version]
  47. Chau, Y.-F.; Yeh, H.-H.; Tsai, D.P. Significantly enhanced birefringence of photonic crystal fiber using rotational binary unit cell in fiber cladding. Jpn. J. Appl. Phys. 2007, 46, L1048. [Google Scholar] [CrossRef]
  48. Yang, K.-Y.; Chau, Y.-F.; Huang, Y.-W.; Yeh, H.-Y.; Tsai, D.P. Design of high birefringence and low confinement loss photonic crystal fibers with five rings hexagonal and octagonal symmetry air-holes in fiber cladding. J. Appl. Phys. 2011, 109, 093103. [Google Scholar] [CrossRef]
  49. Chau, Y.-F.; Yeh, H.-H.; Tsai, D.P. A New Type of Optical Antenna: Plasmonics Nanoshell Bowtie Antenna with Dielectric Hole. J. Electromagn. Waves Appl. 2010, 24, 1621–1632. [Google Scholar] [CrossRef]
  50. Chau, Y.-F.C. Mid-infrared sensing properties of a plasmonic metal–insulator–metal waveguide with a single stub including defects. J. Phys. D Appl. Phys. 2020, 53, 115401. [Google Scholar] [CrossRef]
  51. Wang, D.; Zhu, W.; Yi, Z.; Ma, G.; Xiang, G.; Dai, B.; Yu, Y.; Zhou, G.; Wu, P.; Liu, C. Highly sensitive sensing of a magnetic field and temperature based on two open ring channels SPR-PCF. Opt. Express 2022, 30, 39055–39067. [Google Scholar] [CrossRef]
  52. Isti, M.I.A.; Talukder, H.; Islam, S.M.R.; Nuzhat, S.; Hosen, A.S.M.S.; Cho, G.H.; Biswas, S.K. Asymmetrical D-channel photonic crystal fiber-based plasmonic sensor using the wavelength interrogation and lower birefringence peak method. Results Phys. 2020, 19, 103372. [Google Scholar] [CrossRef]
  53. Chen, Y.; Xie, Q.; Li, X.; Zhou, H.; Hong, X.; Geng, Y. Experimental realization of D-shaped photonic crystal fiber SPR sensor. J. Phys. D Appl. Phys. 2017, 50, 025101. [Google Scholar] [CrossRef]
  54. Al Mahfuz, M.; Hasan, R.; Momota, M.R.; Masud, A.; Akter, S. Asymmetrical photonic crystal fiber based plasmonic sensor using the lower birefringence peak method. OSA Contin. 2019, 2, 1713–1725. [Google Scholar] [CrossRef]
  55. Boyd, D.A.; Greengard, L.; Brongersma, M.; El-Naggar, M.Y.; Goodwin, D.G. Plasmon-assisted chemical vapor deposition. Nano Lett. 2006, 6, 2592–2597. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  56. Lv, J.; Liang, T.; Gu, Q.; Liu, Q.; Ying, Y.; Si, G. A High Refractive Index Plasmonic Micro-Channel Sensor Based on Photonic Crystal Fiber. Nanomaterials 2022, 12, 3764. [Google Scholar] [CrossRef] [PubMed]
  57. Guiyao, Z.; Zhiyun, H.; Shuguang, L.; Lantian, H. Fabrication of glass photonic crystal fibers with a die-cast process. Appl. Opt. 2006, 45, 4433–4436. [Google Scholar] [CrossRef] [PubMed]
  58. Issa, N.A.; van Eijkelenborg, M.A.; Fellew, M.; Cox, F.; Henry, G.; Large, M.C.J. Fabrication and study of microstructured optical fibers with elliptical holes. Opt. Lett. 2004, 29, 1336–1338. [Google Scholar] [CrossRef] [Green Version]
  59. Beltrán-Mejía, F.; Chesini, G.; Silvestre, E.; George, A.K.; Knight, J.C.; Cordeiro, C.M. Ultrahigh-birefringent squeezed lattice photonic crystal fiber with rotated elliptical air holes. Opt. Lett. 2010, 35, 544–546. [Google Scholar] [CrossRef] [Green Version]
  60. Zha, F.; Li, J.; Sun, P.; Ma, H. Highly sensitive selectively coated D-shape photonic crystal fibers for surface plasmon resonance sensing. Phys. Lett. A 2019, 383, 1825–1830. [Google Scholar] [CrossRef]
  61. Wang, S.; Lu, Y.; Ma, W.; Liu, N.; Fan, S. D-Shaped Surface Plasmon Photonic Crystal Fiber Temperature Sensor. Plasmonics 2022, 17, 1911–1919. [Google Scholar] [CrossRef]
  62. Zuhayer, A.; Shafkat, A. Design and analysis of a gold-coated dual-core photonic crystal fiber bio-sensor using surface plasmon resonance. Sens. Bio.-Sens. Res. 2021, 33, 100432. [Google Scholar] [CrossRef]
  63. Akter, S.; Rahman, Z.; Mahmud, S. Highly sensitive open-channels based plasmonic biosensor in visible to near-infrared wavelength. Results Phys. 2019, 13, 102328. [Google Scholar] [CrossRef]
  64. An, G.; Hao, X.; Li, S.; Yan, X.; Zhang, X. D-shaped photonic crystal fiber refractive index sensor based on surface plasmon resonance. Appl. Opt. 2017, 56, 6988–6992. [Google Scholar] [CrossRef]
  65. Lu, J.; Li, Y.; Han, Y.; Liu, Y.; Gao, J. D-shaped photonic crystal fiber plasmonic refractive index sensor based on gold grating. Appl. Opt. 2018, 57, 5268–5272. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  66. Thenmozhi, H.; Rajan, M.S.M.; Ahmed, K. D-shaped PCF sensor based on SPR for the detection of carcinogenic agents in food and cosmetics. Optik 2019, 180, 264–270. [Google Scholar] [CrossRef]
  67. Fu, Y.; Liu, M.; Shum, P.; Chu, L. An ultrahighly sensitive photonic crystal fiber based surface plasmon resonance sensor. Optik 2020, 212, 164649. [Google Scholar] [CrossRef]
  68. Yasli, A.; Ademgil, H.; Haxha, S.; Aggoun, A. Multi-Channel Photonic Crystal Fiber Based Surface Plasmon Resonance Sensor for Multi-Analyte Sensing. IEEE Photonics J. 2020, 12, 1–15. [Google Scholar] [CrossRef]
  69. Chu, S.; Nakkeeran, K.; Abobaker, A.M.; Aphale, S.S.; Sivabalan, S.; Babu, P.R.; Senthilnathan, K. A surface plasmon resonance bio-sensor based on dual core D-shaped photonic crystal fibre embedded with silver nanowires for multisensing. IEEE Sens. J. 2020, 21, 76–84. [Google Scholar] [CrossRef] [Green Version]
  70. Yan, X.; Fu, R.; Cheng, T.; Li, S. A Highly Sensitive Refractive Index Sensor Based on a V-Shaped Photonic Crystal Fiber with a High Refractive Index Range. Sensors 2021, 21, 3782. [Google Scholar] [CrossRef]
  71. Rahman, A.; Ahmed, T.; Haque, I.; Anower, S. A Photonic Crystal Fiber Based Asymmetric Slotted Structured Highly Sensitive Refractive Index Plasmonic Biosensor. J. Sens. Technol. 2022, 12, 1–17. [Google Scholar] [CrossRef]
Figure 1. Cross-section of the designed SPR-PCF sensor with structural parameters.
Figure 1. Cross-section of the designed SPR-PCF sensor with structural parameters.
Photonics 09 00916 g001
Figure 2. Real parts of the effective RIs of the core-guided mode (red dashed line) and SPP mode (black dashed line), and the confinement loss (CL) of core-guided mode (blue curve).
Figure 2. Real parts of the effective RIs of the core-guided mode (red dashed line) and SPP mode (black dashed line), and the confinement loss (CL) of core-guided mode (blue curve).
Photonics 09 00916 g002
Figure 3. E-field distributions of the (a) SPP mode and (b) core-guided mode (y-polarized).
Figure 3. E-field distributions of the (a) SPP mode and (b) core-guided mode (y-polarized).
Photonics 09 00916 g003
Figure 4. Confinement loss spectra of the core-guided mode for various Au thicknesses, tAu = (10, 15, 20, 25, 30, 35, 40, 50) nm.
Figure 4. Confinement loss spectra of the core-guided mode for various Au thicknesses, tAu = (10, 15, 20, 25, 30, 35, 40, 50) nm.
Photonics 09 00916 g004
Figure 5. Confinement loss spectra of the core-guided mode for a1y = (0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90) µm.
Figure 5. Confinement loss spectra of the core-guided mode for a1y = (0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90) µm.
Photonics 09 00916 g005
Figure 6. Confinement loss spectra of the core-guided mode for a2y = (0.68, 0.70, 0.72, 0.74, 0.76, 0.78) µm.
Figure 6. Confinement loss spectra of the core-guided mode for a2y = (0.68, 0.70, 0.72, 0.74, 0.76, 0.78) µm.
Photonics 09 00916 g006
Figure 7. Confinement loss spectra of the core-guided mode for a3y = (0.35, 0.36, 0.37, 0.38, 0.39, 0.40, 0.41, 0.42) µm.
Figure 7. Confinement loss spectra of the core-guided mode for a3y = (0.35, 0.36, 0.37, 0.38, 0.39, 0.40, 0.41, 0.42) µm.
Photonics 09 00916 g007
Figure 8. Confinement loss spectra of the core-guided mode for ellipticity (e = 0.40, 0.50, 0.55, 0.60, 0.65, 0.70, 0.75, and 1.00).
Figure 8. Confinement loss spectra of the core-guided mode for ellipticity (e = 0.40, 0.50, 0.55, 0.60, 0.65, 0.70, 0.75, and 1.00).
Photonics 09 00916 g008
Figure 9. Confinement loss spectra of the core-guided mode for the distance between the top elliptical air hole and the flat surface (h = 0.1, 0.2, 0.3, 0.4, 0.5, and 0.6 µm).
Figure 9. Confinement loss spectra of the core-guided mode for the distance between the top elliptical air hole and the flat surface (h = 0.1, 0.2, 0.3, 0.4, 0.5, and 0.6 µm).
Photonics 09 00916 g009
Figure 10. Confinement loss spectra of the core-guided mode for different RIs of analytes (nana), (a) nana = 1.31, 1.32, 1.33, 1.34 and 1.35 and (b) nana = 1.36, 1.37, 1.38, 1.39, 1.391, 1.392, 1.393 and 1.395.
Figure 10. Confinement loss spectra of the core-guided mode for different RIs of analytes (nana), (a) nana = 1.31, 1.32, 1.33, 1.34 and 1.35 and (b) nana = 1.36, 1.37, 1.38, 1.39, 1.391, 1.392, 1.393 and 1.395.
Photonics 09 00916 g010
Figure 11. Resonance wavelength (nm) and confinement loss spectra of the core-guided mode for different analytes (nana) ranging from 1.31 to 1.3950.
Figure 11. Resonance wavelength (nm) and confinement loss spectra of the core-guided mode for different analytes (nana) ranging from 1.31 to 1.3950.
Photonics 09 00916 g011
Table 1. The constant values of the Sellmeier Equation.
Table 1. The constant values of the Sellmeier Equation.
B1B2B3C1C2C3
0.6961630.40794260.8974794000.00467914860.013512063197.9340025
Table 2. The constant values of Equation (2).
Table 2. The constant values of Equation (2).
εωωD/2πγD/2πΩLΓL/2π
5.96732πc/λ2113.6 THz15.9 THz650.07 THz104.86 THz
Table 3. Initial geometrical parameters of the designed SPR-PCF.
Table 3. Initial geometrical parameters of the designed SPR-PCF.
a1x
(μm)
a1y
(μm)
a2x
(μm)
a2y
(μm)
a3x
(μm)
a3y
(μm)
etAu
(nm)
h
(μm)
nana
0.8e0.80.7e0.70.2e0.40.6300.41.38
Note: e is ellipticity.
Table 4. Optimal geometrical parameters of the proposed SPR-PCF.
Table 4. Optimal geometrical parameters of the proposed SPR-PCF.
a1x
(μm)
a1y
(μm)
a2x
(μm)
a2y
(μm)
a3x
(μm)
a3y
μm)
etAu
(nm)
h
(μm)
0.7e0.70.78e0.780.35e0.350.55300.4
Note: e is ellipticity.
Table 5. Observation of the performance of the designed SPR-PCF sensor for variation of RIs in the interval of 1.31–1.395.
Table 5. Observation of the performance of the designed SPR-PCF sensor for variation of RIs in the interval of 1.31–1.395.
nanaCL (dB/cm)λpeak (cm)Sensor Length (cm)Sensitivity (nm/RIU)Resolution (RIU)
1.3124.625540.040611009.0909 × 10−5
1.3231.555650.031611009.0909 × 10−5
1.3341.785760.023913007.6923 × 10−5
1.3457.315890.0174417005.8823 × 10−5
1.3581.866060.0122124004.1667 × 10−5
1.36132.26300.0075631003.2258 × 10−5
1.37252.346610.0039650002.0000 × 10−5
1.38478.117110.0020988001.1363 × 10−5
1.391205.007990.0008316,0005.8823 × 10−5
1.3911288.208150.0007818,0005.56 × 10−6
1.3921297.908330.0007716,0006.25 × 10−6
1.3931367.008490.00073116,5008.58 × 10−7
1.3953121.8010820.00032N/AN/A
Table 6. Performance analysis comparison between the proposed SPR-PCF sensor and previously reported sensors.
Table 6. Performance analysis comparison between the proposed SPR-PCF sensor and previously reported sensors.
Refs./YearRI RangeWavelength Range (nm)Max. Sensitivity (nm RIU−1)Resolution (RIU)
[64]/20171.32–1.35650–85056009.650 × 10−6
[65]/20181.40–1.43904–135915,1805.600 × 10−6
[66]/20191.414–1.4241900–220050,0004.000 × 10−4
[67]/20201.39–1.43650–140021,2004.720 × 10−6
[68]/20201.33–1.36400–80030833.200 × 10−5
[69]/20211.35–1.501800–220040002.940 × 10−5
[70]/20211.43–1.49900–125012,7197.460 × 10−6
[41]/20221.33–1.39600–96013,0001.075 × 10−6
[71]/20221.30–1.44800–110011009.090 × 10−6
This work1.31–1.3950550–1200116,5008.58 × 10−7
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Chao, C.-T.C.; Kooh, M.R.R.; Chau, Y.-F.C.; Thotagamuge, R. Susceptible Plasmonic Photonic Crystal Fiber Sensor with Elliptical Air Holes and External-Flat Gold-Coated Surface. Photonics 2022, 9, 916. https://doi.org/10.3390/photonics9120916

AMA Style

Chao C-TC, Kooh MRR, Chau Y-FC, Thotagamuge R. Susceptible Plasmonic Photonic Crystal Fiber Sensor with Elliptical Air Holes and External-Flat Gold-Coated Surface. Photonics. 2022; 9(12):916. https://doi.org/10.3390/photonics9120916

Chicago/Turabian Style

Chao, Chung-Ting Chou, Muhammad Raziq Rahimi Kooh, Yuan-Fong Chou Chau, and Roshan Thotagamuge. 2022. "Susceptible Plasmonic Photonic Crystal Fiber Sensor with Elliptical Air Holes and External-Flat Gold-Coated Surface" Photonics 9, no. 12: 916. https://doi.org/10.3390/photonics9120916

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop