Skip to Content
ProcessesProcesses
  • Article
  • Open Access

26 March 2026

21 Pages

Porous Activated Carbons from Olive Stone-Derived Biochar and Hydrochar: Production, Characterization and Application for Amoxicillin Removal

,
,
,
and
1
Laboratory of Chemistry and Environmental Science (LCSE), University of Bechar-Tahri Mohamed, Bechar 08000, Algeria
2
Laboratoire de Génie des Procédés Environnement et Agro-Alimentaire (GEPEA), UMR CNRS 6144, Ecole Mines-Télécom, F-44307 Nantes, France
3
Centre for Environmental Studies and Research, Sultan Qaboos University, Al-Khoud 123, Muscat P.O. Box 17, Oman
4
The Institute of Materials Science of Mulhouse (IS2M), University of Haute Alsace, University of Strasbourg, CNRS, UMR 7361, F-68100 Mulhouse, France

Abstract

The sustainable management of olive wastes represents an important environmental challenge. Biochars and hydrochars derived from biomass are promising adsorbents for removing emerging pollutants from water. In the present work, olive stone wastes were converted into biochar and hydrochar by using pyrolysis (500 °C for 30 min) and hydrothermal carbonization (HTC) processes (220 °C for 10 h). Then, the obtained materials were physically activated by using CO2 gas (750 °C for 30, 60 and 180 min). Various analytical techniques were applied for the chemical, textural and structural characterization of these carbonaceous materials (i.e., ultimate and proximate analysis, scanning electron microscopy (SEM), BET surface area, Raman spectroscopy, X-ray diffraction, and Fourier transform infrared spectroscopy). Afterwards, the selected activated biochar and hydrochar were applied for the removal of amoxicillin from aqueous solutions. The experimental results show that the generated hydrochar has many microspheres on its surface and inside, while the produced biochar exhibits a porous structure with irregular forms. CO2 physical activation has induced an important improvement of the biochar and hydrochar’s structural, textural, and surface chemistry properties. For instance, the activated biochar samples show a highly porous structure, with large specific surface areas that increase with the burn-off, reaching 1349.3 m2 g−1 following 3 h of activation. Regarding the activated hydrochar samples, they exhibit a spherical morphological structure with an important specific surface area, which increased to 846.7 m2 g−1 after 3 h of activation. Moreover, both activated materials have an amorphous structure with low oxygen surface groups. The selected novel CO2-activated biochar and hydrochar efficiently remove amoxicillin from aqueous solutions under wide experimental conditions, with adsorption capacities of 386.4 and 215.9 mg g−1, respectively. These efficiencies are higher than those reported for various activated biochars derived from lignocellulosic biomass, from sewage sludge, and from animal manure. Future research works are required to assess these materials’ effectiveness in treating real pharmaceutical effluents, to optimize the regeneration of the amoxicillin-loaded materials, and to design full-scale devices for a real application.

1. Introduction

Since ancient times, olive oil production has been considered an important agricultural, social and economic activity in the Mediterranean region [1]. According to the International Olive Council [2], global olive oil production has significantly increased over the past decades, with Mediterranean countries accounting for the majority of production. However, this important sector generates huge amounts of olive mill solid wastes and also olive stones [3]. The sustainable management of these wastes has been pointed out as an important environmental challenge in the Mediterranean region [4,5]. Indeed, they have a specific composition, permitting their potential valorization in various domains including energy, water, agriculture, and environment [6,7].
Various thermochemical conversion technologies have been intensively tested over the last decades for the management of lignocellulosic biomass wastes, including olive solid wastes. They mainly include hydrothermal carbonization (HTC) [8,9] and pyrolysis [4,6]. HTC is adapted for wet biomass and is carried out at a high pressure but under relatively low temperatures (between 180 °C and 280 °C) [10]. The main targeted bio-products are bio-oil and a solid residue called hydrochar [11]. The pyrolysis process is a thermal degradation of dry biomass that occurs in the absence of oxygen but at much higher temperatures (between 300 °C and 900 °C) [12]. This process leads to three by-products: bio-oil, syngas and a solid residue named biochar [13]. The physico-chemical properties of the hydrochars and biochars are very dependent on the nature of the biomass and also on the thermochemical experimental conditions such as the final temperature and the residence time [14,15]. Depending on these characteristics, raw hydrochars and biochars may be applied in various energy, environmental and agriculture applications [16,17].
Pharmaceuticals, along with other substances such as micro- and nano-plastics, herbicides, and pesticides, are considered as serious emerging contaminants. Indeed, even at low concentrations, they can seriously impact human health and ecosystems quality [18]. Over the past decades, pharmaceuticals have increasingly been detected in ecosystems in general and particularly in water resources [19]. Amoxicillin is an active compound that belongs to the penicillin family. It is widely used around the world and especially in Europe [20]. Almost 80% of the ingested amoxicillin can be excreted into urine and therefore transferred to wastewater treatment plants [21]. Numerous methods have been tested for the removal of amoxicillin from wastewater, such as membrane filtration and advanced oxidation processes. However, the full-scale application of these technologies is very limited due to their high cost and the possible production of toxic by-products [22]. Pharmaceutical adsorption onto engineered materials such as biochars has been highlighted as an eco-friendly, highly effective, low-cost and practical technology [23]. Moreover, the use of biochars/hydrochars for the removal of amoxicillin from aqueous solutions could be emphasized by numerous advantages such as sustainability and circular economy boosting, environment preservation for future generations, and suitability for large-scale application [24].
Various raw and modified biochars and hydrochars have been synthesized and used for pharmaceutical removal from aqueous solutions [25,26]. These investigations show that the raw feedstock nature, the pyrolysis or HTC conditions and the pharmaceuticals properties play an important role in shaping the physico-chemical characteristics of the biochars/hydrochars and consequently their removal efficiency removal. In addition, the highest removal efficiencies for pharmaceuticals are usually observed for activated biochars or hydrochars. For instance, rice husk-derived hydrochar activation with 1 M H3PO4 exhibited an exceptionally high removal capacity for tetracycline (419 mg g−1) [27]. Likewise, the activation of palm kernel shell-derived biochar with a KOH at a mass ratio of 1:3 allows for a high amoxicillin removal capacity (220 mg g−1).
The use of biochars and hydrochars derived from olive wastes for the removal of amoxicillin from wastewater can contribute to resolving an important Mediterranean challenge regarding the sustainable management of both solid and liquid wastes. However, raw olive waste-derived biochars and hydrochars have a limited adsorption capacity due to their low surface areas and functional groups density, which seriously limit their effective use for pollutant removal from aqueous solutions [15,28]. To tackle this issue, these hydrochars and biochars may undergo physical and/or chemical modifications to obtain engineered materials (i.e., activated carbons) with improved properties [9,29]. Even if the use of physical modification process is more attractive owing to its eco-friendless and also effectiveness [30], chemical modification has been widely applied for the treatment of olive stones due to its simplicity [31]. In this context, Fadhil and Kareem [10] studied the pyrolysis of olives stones and date pits at a temperature of 500 °C and a residence time of 1 h. They showed that the produced biochar has relatively poor physico-chemical characteristics. This biochar activation with zinc chloride (ZnCl2) allowed a substantial improvement of its structural, textural and chemical surface properties. For instance, the BET surface area reached 936 m2 g−1. Likewise, olive stone-derived hydrochar modification significantly improves textural and surface chemistry properties. For example, Diaz et al. [9] showed that the chemical activation of olive stone-derived hydrochar with H3PO4 and KOH increased the BET surface area from less than 20 m2 g−1 to 1115 and 2122 m2 g−1, respectively. Moreover, important amounts of acidic and basic functional groups are detected on the surface of H3PO4- and KOH-activated hydrochars, respectively. However, in the scientific literature, there is a lack of studies on the thermal activation of hydrochars using CO2. To the best of our knowledge, no published work has compared the physicochemical characteristics of physically activated carbons produced from olive stone-derived hydrochars and biochars. Although some studies have investigated the use of olive waste-derived biochars and hydrochars for the treatment of wastewater containing emerging pollutants [31], previous research comparing biochar and hydrochar for antibiotic adsorption has generally reported higher adsorption capacities for biochars due to their larger surface area and higher degree of carbonization [28,31,32]. Nevertheless, a direct comparison between CO2-activated hydrochar and biochar from olive solid wastes for amoxicillin removal has not yet been reported.
Moreover, the effective management of pharmaceutical-loaded materials is particularly important in order to avoid any subsequent pollution. Previous research works have shown the potential for several adsorption–regeneration cycles by using various eluent solutions (i.e., NaOH, ethanol, NaCl, etc.) [25,26]. The pharmaceutical-rich desorbed solutions may be treated through advanced oxidation processes by specific reactive radicals [33].
Hence, this work aims to find an innovative solution for the sustainable management of olive stone wastes and pharmaceutical-rich wastewater. Such an approach turns abundant wastes into high-value-added materials and consequently boosts environmental sustainability and circular economy. The specific objectives are: (i) the synthesis and deep characterization of various raw CO2-activated biochars and hydrochars from olive stone waste and the selection of the activated biochar and hydrochar with the best properties; (ii) the application of these materials for amoxicillin removal from aqueous solutions under wide experimental conditions and the comparison of their effectiveness with other engineered materials.

2. Materials and Methods

2.1. Biochar and Hydrochar Production

In this study, olive stone (OS) samples were collected from the “Mazzitti” olive oil mill plant in Terai Baienan (Mila, Algeria). Firstly, olive stones were washed several times with tap water to remove impurities and residual traces of olive mill wastewater. Afterward, this washed sample was dried in an oven at 105 °C for 24 h. The hydrochar was produced following the procedure described in Bourafa et al. [8]. Briefly, 30 g of dried olive stones and 90 mL of distilled water are mixed in a 250 mL Teflon-lined stainless-steel autoclave and then placed in the oven at 220 °C for 10 h. Regarding the biochar production, the dried olive stones are pyrolyzed using a horizontal tubular laboratory furnace (Nabertherm, Lilienthal, Germany) under nitrogen atmosphere. The temperature was gradually raised to 500 °C at a heating rate of 10 °C/min and maintained for 30 min. After that, the system is naturally cooled until reaching ambient temperature. The obtained hydrochar and biochar are named HYD220 and BIO500, respectively.
The hydrochar and biochar production yields (Y) were calculated using the following relation:
Y ( % ) = M a s s   o f   h y d r o c h a r / b i o c h a r M a s s   o f   f e e d s t o c k   ×   100

2.2. Synthesis of the Activated Carbons

The activation of the prepared hydrochar and biochar in Section 2.1 was performed in alumina crucibles placed in the same furnace. This activation process consists of the following steps: (i) heating the system from ambient temperature to 750 °C at a heating rate of 40 °C min−1 under a constant nitrogen gas flow of (100 mL min−1), (ii) CO2 injection at a flow rate of 100 mL min−1 at 750 °C for three different contact times of 30, 60 and 180 min, and (iii) cooling under a nitrogen atmosphere at a flow rate of 40 mL min−1 until reaching room temperature.
The burn-off values of the activated hydrochar/biochar were calculated using the difference between their initial and final weights as follows:
B O ( % ) = M a s s   h y d r o c h a r / b i o c h a r − M a s s   a c t i v a t e d   c a r b o n M a s s   h y d r o c h a r / b i o c h a r × 100
The prepared activated carbons are labeled HYD220-t and BIO500-t. The “t” corresponds to the duration of the activation process (h).

2.3. Characterization of the Carbon Materials

Several techniques were used for the characterization of the olive stones and the prepared hydrochar/biochar and their activated forms. They include: (i) ultimate analysis using an elemental analyzer to determine the elemental contents (wt%) of carbon (C), hydrogen (H), nitrogen (N), and sulfur (S); (ii) proximate analysis, which consists of determining the fixed carbon, volatile matter, and ash contents, assessed through thermogravimetric analysis (TGA); and (iii) the examination of surface morphologies using scanning electron microscopy (SEM). The textural characterization was performed through nitrogen (N2) adsorption at −196 °C and carbon dioxide (CO2) at 0 °C. This analysis allows us to determine the Brunauer–Emmett–Teller (BET) surface area, the total volume porosity, and the volume microporosity of the samples. (iv) The structure of the samples was analyzed using a RAMAN spectrometer (LabRAm HR Evolution—HORIBA Scientific, Piscataway, NJ, USA); (v) the pH of point of zero charge (pHpzc) of the selected materials was assessed by using the pH drift method for initial pH values varying between 4 and 10 [34]; (vi) samples’ crystallinity was studied through X-ray diffraction (XRD); and (vii) the available functional groups at the surface of the tested sample were identified through FT-IR spectroscopy. Further details on the instruments and their specifications are provided in Text S1 in the Supplementary Materials.

2.4. Batch Adsorption Experiments

To prepare the amoxicillin solutions, a stock solution of 1 g L−1 was obtained by dissolving 1 g of amoxicillin powder in distilled water and adjusting the volume to 1 L. For the adsorption kinetic experiments, 500 mL of amoxicillin solution at an initial given concentration was mixed with 0.5 g of activated hydrochar or activated biochar. Then, this flask was stirred at 300 rpm using a magnetic stirrer. If not specified, the following defaults parameters were used: an initial amoxicillin concentration of 100 mg L−1, an adsorbent dose of 1 g L−1, a contact time varying between 5 and 420 min, a natural pH (without adjustment: around 6.8), and a temperature of 20 °C. Adsorption isotherms were conducted at initial amoxicillin concentrations ranging from 5 to 800 mg/L, and finally the effect of the pH was determined using aqueous pH-spanning acidic and alkaline media for values varying between 4 and 12. Table 1 gives a summary of the batch experiment parameters.
Table 1. Experimental batch conditions for the study of amoxicillin removal by the activated biochar and hydrochar.
In this study, the concentrations of amoxicillin were determined by using a spectrophotometer (6850 JENWAY, Cole-Parmer, Vernon Hills, IL, USA) at a wavelength of 227 nm. The adsorbed amount of amoxicillin qe (mg g−1) was calculated using the following equation:
q e = C 0 − C e m V
where C0 and Ce are the initial and equilibrium concentrations (mg L−1), respectively. V is the volume (L) of solution and m is the quantity of the solid.
Moreover, the kinetic adsorption experimental data for the activated hydrochar and biochar were fitted to two common models, namely the pseudo-first-order (PFO) and the pseudo-second-order (PSO) models. The equations of these kinetic models are given in Table S1. Moreover, the isotherm experimental data of amoxicillin for the two tested adsorbents were fitted with widely applied adsorption models: Langmuir, Freundlich and Dubinin–Radushkevich (D-R) models. The equations of these isotherm models are given as follows:
L a n g m u i r   m o d e l : q e = q m , L   K L   C e 1 + K L   C e
F r e u n d l i c h   m o d e l :   q e = K F   C e 1 / n
D - R   m o d e l :   q e = q m , D − R   exp [ − β ε 2 ]
where qe is the adsorbed amount on the solid material at equilibrium; Ce is the residual concentration in the aqueous phase at equilibrium; qm,L is the Langmuir’s adsorption capacity; KL is Langmuir’s coefficient; KF is the Freundlich coefficient; n is the Freundlich parameter; qm,D-R is the adsorption capacity of the D-R model; β is the constant related to the adsorption energy; and ε is the Polanyi potential.
Each experiment was performed at least in duplicate, and the average values are given in this work.

2.5. Statistical Analysis

Excel 2016 was used for the regression analysis of the experimental and calculated data and also for figure plotting. The error bars in the curves represent the standard deviations estimated from the duplicate batch assays.

3. Results and Discussion

3.1. Characterization of the Raw and Carbonized Materials

3.1.1. Elemental, Proximate and Thermogravimetric Analyses

Table 2 presents the elementary and proximate analysis of olive stones and the generated hydrochar and biochar under the experimental conditions given in Section 2.3.
Table 2. Elemental and immediate analysis of the raw material, biochar, and hydrochar (MC: moisture content, VM: volatile matter, FC: fixed carbon; DL: detection limit of the device; QL: quantification limit; a: by difference: O (%) = 100% − (C + H+N + Ash)).
The thermal decomposition processes of the pyrolysis process usually involve dehydration, the formation of carbonyl groups and then their elimination, the decomposition of aliphatic molecules and finally the formation of an aromatic structure that increases the graphitic planes of the biochars [35]. HTC typically begins with the hydrolysis of biomass to oligomers and monomers, then follows the same steps of pyrolysis (dehydration, decarboxylation, aromatization, and polymerization) [36]. These steps affect the results of elemental components and the structure of the formed biochars and hydrochars.
The ultimate analysis shows that both pyrolysis and HTC significantly increase the carbon content of the raw material. Hydrochar retains more oxygen than biochar. This is expected and can be mainly attributed to the low temperature used for HTC (220 °C) compared to the pyrolysis process (500 °C). Meanwhile, the nitrogen content decreases after both treatments, which will result in a reduction of nitrogen-based functional groups and possibly pollutant removal efficiency. A similar finding was reported by Azzaz et al. when studying olive mill solid waste conversion through HTC and pyrolysis [15]. Furthermore, no traces of sulfur were detected in any of the studied samples, in agreement with previous studies. For instance, Román et al. reported a negligible sulfur content in hydrochars from various biomass sources [37], and Hernandez-Mena et al. observed similar results for biochars from bamboo [38]. Regarding the proximate analysis, the results show a decrease in the content of volatile matter after pyrolysis and HTC, while the fixed carbon content increases due to the decomposition process. This effect is less pronounced for the hydrochar sample compared to the biochar. This finding can be attributed to the lower temperature used in the HTC process, which might induce an incomplete removal of cellulose fractions from the precursor [39]. Furthermore, a decrease in the moisture content was observed after both processes, with a greater reduction observed for pyrolysis compared to the HTC process. This difference is due to the fact that HTC took place in an aqueous medium.
The DTG curve of the raw olive stone biomass exhibits three distinct peaks (Figure 1). They are observed at temperatures of 100 °C, 300 °C, and 360 °C, corresponding to moisture evaporation, hemicellulose, and cellulose decomposition [40]. A significant mass loss was observed during lignin degradation. These findings are consistent with previous studies [35,40].
Figure 1. Thermogravimetric analysis (TGA-DTG) of raw olive stones.

3.1.2. Surface Morphology

The surface morphology of olive stones and their derived hydrochar and biochar are given in Figure 2. The related SEM images reveal the presence of multiple spheres with varying sizes exclusively in the hydrochar sample. These microspheres are formed due to the impact of HTC on the raw biomass. Indeed, the HTC process triggers the decomposition of cellulose and hemicellulose, leading to the formation of these distinct microspheres on the surface of the hydrochar. These results are consistent with our previous work on hydrochars from date and olive stones [8], while highlighting the novel observation of microsphere formation, which differs from other biomass sources [35].
Figure 2. Raman spectra of: (a) hydrochar and biochar, (b) CO2-activated hydrochar and (c) CO2-activated biochar.
Figure S2 shows the surface morphology of the activated hydrochar and activated biochar under the same conditions (750 °C, 180 min, and CO2 flow at 100 mL min−1). The activated hydrochar shows a remarkable development in the surface structure where the surface particles are covered with microspheres, with the presence of some cavities. The activated biochar shows a high development in the porosity with the appearance of different pores on the surface.

3.1.3. Textural Properties

Figure S3a,b show the nitrogen adsorption–desorption isotherms at −196 °C for the biochar and hydrochar prepared from olive stones at temperatures of 500 °C and 220 °C, respectively. The use of the IUPAC classification indicates that the biochar has a non-microporous surface. Likewise, the hydrochar exhibits a low adsorption at low relative pressures, indicating a limited porosity. These results are consistent with those obtained by Diaz et al. [9]. However, the adsorption isotherms of the activated hydrochar and activated biochar are of type I (Figure S3c,d). This indicates that micropores predominate, with a certain degree of mesoporosity for the hydrochar (presence of hysteresis loops). Moreover, for both activated materials, the increase in the activation time leads to an increase in the burn-off percentage and consequently in the quantity of adsorbed gas, which represents evidence of porosity development.
Table 3 shows the yield, the burn-off percentages and the textural properties of the biochar, hydrochar and their derived CO2-activated carbons. The production yield of the hydrochar is higher than the biochar. Indeed, the highest used temperature during the pyrolysis process induces a higher organic mass loss [14,41]. After activation, the BO of the activated carbon increases with a prolonged activation time due to the ongoing reaction between carbon dioxide and amorphous carbon, creating micropores. The activation degree (burn-off) percentages are lower at activation times of 0.5 and 1 h for the activated biochars compared to the activated hydrochars (Table 3). In addition, both the HTC and pyrolysis methods allow a minimal increase in the porosity, but the hydrochar has a more important pore volume and surface area compared to the biochar. However, CO2 activation has significantly impacted the textural properties of the olive stone-derived biochar and hydrochar (Table 3). Indeed, the BET surface area increases from 1.8 m2 g−1 to 625.2 m2 g−1 for the biochar after 30 min of activation time and from 18.2 m2 g−1 to 522.5 m2 g−1 for the hydrochar after the same activation time. The increase in the burn-off leads to more developed porosities (i.e., reaction between CO2 and the walls of pores), and this behavior is more pronounced for the activated biochar. For instance, after 3 h of activation, the resulting biochar has a considerable BET surface area (1349 m2 g−1), which is around 59.5% higher than that measured for the activated hydrochar under the same conditions. This increase is also reflected in the activated carbon micropore volumes, where a continuous increase for Vmicro(N2) and V(CO2) is observed. The development of micropore and mesopore volumes is more pronounced for activated biochars than activated hydrochars (Table 3). This behavior can be explained by the role of CO2 as an activating agent that contributes to the developing microporosity and mesoporosity for both tested feedstocks. Hence, CO2 activation acts in the same way for biochar and hydrochar in developing porosity, which is in agreement with the mechanism of CO2 activation (C + CO2 → 2CO) [42]. Similar results were reported for CO2-activated biochar derived from date pits, where the surface area attained 1443 m2 g−1 at a burn-off of 50% [30].
Table 3. Textural characteristics of hydrochars, biochars and activated carbons issued from CO2 activation (-: not relevant).

3.1.4. Structural Characterization

RAMAN Analysis
The characterization of ordered and amorphous carbons, as well as the exploration of structural characteristics, has been performed using Raman spectroscopy. This technique allows for the estimation of the extent of graphene by examining the ratio between the intensities of the D-band (defects) and the G-band (graphite) [43]. The Raman spectra of the carbonaceous materials within the range of 800 to 2000 cm−1 exhibit two distinctive bands (Figure 2). Specifically, between 1330 and 1340 cm−1, the disorder-induced D-band is observed, which can be attributed to disordered carbon or defective graphitic structures. These bands result from in-plane vibrations of sp2-bound carbon within structural defects. Additionally, a band is observed between 1583 and 1603 cm−1, known as the graphite (G) band. This band likely represents graphitic layers and arises due to in-plane vibrations of sp2-bonded microcrystalline carbon [44]. Table S2 provides a summary of the key information extracted from the Raman spectra of the biochar and hydrochar and their CO2-activated forms. It includes the positions of the D and G bands, the intensities of the band peaks, and the ID/IG band ratio.
Figure 2a and Table S2 reveal that the total Raman intensity of the D and G bands in the olive stone-derived biochars are significantly lower compared to the ones for the hydrochars. Following the activation of both precursors, as depicted in Figure 2b,c, it is evident that the overall Raman intensity of the activated carbons gradually diminishes as the activation time increases. This observation may be due to the loss of sensitive groups like aliphatic and oxygen groups during the activation process, leading to an increase in the aromatic composition of the carbonaceous materials [43,45]. This increase in aromatic composition enhances light absorption properties.
The ID/IG ratio is commonly employed to assess the crystalline or amorphous (graphite-like) carbon structure [43,44]. A high ID/IG ratio indicates low graphitization [46]. In Figure 2a, it is evident that the G band exhibits a higher intensity than the D band for both the olive stone-derived hydrochar and biochar. The calculated ID/IG ratios are equal to 0.81 and 0.83 for the hydrochar and biochar, respectively, indicating an amorphous structure for both materials. In the case of the activated carbon samples, the degree of graphitization ranges from 1.03 to 1.08 for the activated hydrochars and from 1.03 to 1.10 for the activated biochars (Table S2). These findings suggest that the disordered graphite present in the carbonaceous materials possesses an amorphous structure with numerous lattice edges (defects) at the planar ends [47].
XRD Analysis
Figure 3a,b display the XRD spectra of the olive stone-derived hydrochar and biochar and their activated forms for a residence time of 1 h, respectively. These spectra show the presence of two broad peaks located at approximately 2θ∼20, corresponding to the (0 0 2) plane, and 2θ∼44, along with a less intense peak at 42.6, which corresponds to the (1 0 0) plane of the nanocrystalline graphite lattice. This indicates that the resulting carbonaceous materials possess a high degree of amorphousness (as evident in the first peak) and crystallinity (second peak). The amorphous nature of all the samples is further supported by the broad characteristics observed in the two peaks [40,46]. Additionally, the process of HTC leads to the removal of the microcrystalline structure, aligning with the behavior observed in the pyrolysis process. This phenomenon can be attributed to the thermal degradation of cellulose and the disruption of its crystalline regions under hydrothermal conditions, as reported in previous studies [10,48].
Figure 3. XRD analysis of (a) hydrochar and biochar from olive stone waste; (b) activated carbon of the two precursors for an activation time of 1 h.

3.1.5. Surface Chemistry

FTIR analyses were performed to identify the molecular components and functional groups present on the surface of olive stone-derived hydrochar and biochar, as well as their CO2-activated forms for a residence time of 1 h. The hydrochar spectrum (HYD220) reveals distinct functional groups (Figure 4a). Bands at the wavenumber range between 3600 and 2800 cm−1 indicate the presence of hydroxyl (-OH) and carboxyl (COOH) groups [15]. Moreover, the absorption gaps observed between 2850 and 2918 cm−1 are primarily attributed to the C-H stretching vibrations of aliphatic molecules [49]. At 1747 cm−1, a peak corresponding to carbonyl vibrations (C=O) (specifically from the carboxyl group in cellulose) is observed [50]. Additionally, the band at 1650 cm−1 suggests the presence of alkene stretching vibrations (C=C) potentially originating from the aromatic rings in lignin. Further peaks exist at around 1450, 1420, 1364, and 1313 cm−1 and correspond to stretching vibrations of C=N, deformation of C-H bonds, CH2 bending in cellulose and hemicellulose, and stretching vibrations of -CH2/-CH3 groups in esters, respectively [49]. The compressed bands between 927 and 1127 cm−1 are associated with C-O bond stretching vibrations in cellulose and hemicellulose [35]. The bands between 1021 and 1099 cm−1 indicate the presence of C-O functional groups [8,51]. Lastly, the bands at 750 and 865 cm−1 are assigned to the out-of-plane bending vibrations of C-H bonds in the aromatic ring structure [49]. Similarly, the biochar spectrum exhibits specific functional groups within the same wavenumber range (Figure 4a). However, all the infrared peaks observed in the spectrum of HYD220 are more intense than those of BIO500, which indicates a higher concentration of functional groups in the hydrochar. This intensity difference suggests that HYD220 retains a greater number of original functional groups from the raw material due to its lower degree of thermal decomposition during the HTC process. Moreover, the relatively lower intensity of the peaks in the spectrum of BIO500 indicates a higher degree of carbonization and a reduction in the number of functional groups present in the raw olive stones. This finding proves that, compared to the hydrochar, the biochar underwent a more extensive thermal degradation, resulting in a more carbon-rich and structurally simplified material. Similar results were observed with biochars prepared from Miscanthus and corncob feedstocks through slow pyrolysis at 800 °C and a heating rate 2.5 °C min−1 [51].
Figure 4. FTIR analyses of (a) the olive stone-derived hydrochar and biochar and (b) their derived activated carbons for a residence time of 1 h.
The FTIR spectra of the activated hydrochar and activated biochar show a lower intensity of peaks compared to their corresponding feedstock. Furthermore, certain bands that are originally present in the hydrochar and biochar spectra have completely disappeared in the activated carbon spectra (Figure 4b). This behavior can be attributed to the high temperature used in the activation process (750 °C). At such a high temperature, surface complexes and less stable functional groups can be eliminated, and only the most stable functional groups remain on the activated carbons surface [47].
The pH of the point of zero charge of HYD-220-0.5 and BIO500-0.5 were assessed as being 7.96 and 8.07, respectively. This result indicates that, for pH values lower than 8.0–8.1, these materials will be mainly positively charged and could attract negatively charged amoxicillin molecules.

3.2. Amoxicillin Removal Study

Amoxicillin removal efficiency was studied for the activated hydrochar, HYD220-0.5, and the activated biochar, BIO500-0.5. The choice of an activation time of 0.5 h is justified by the fact that the porosities of these two materials are close to those measured for an activation time of 1 h (see Table 2). Additionally, for economic reasons, the activated hydrochar and biochar produced for a long activation time of 3 h (HYD220-3 and BIO500-3) were not considered for further investigation in this study, even if they have better physico-chemical properties.

3.2.1. Impact of Contact Time—Kinetic Study

The adsorption kinetic study was carried out under the experimental conditions given in Section 2.4. This study aims to determine the contact time required to reach an equilibrium state in the system. The experimental data (Figure 5) show that the amoxicillin adsorption by the HYD220-0.5 and BIO500-0.5 occurs rapidly during the first hour, indicating the availability of a large number of free adsorption sites. At this time, the adsorbed amoxicillin amount for the activated hydrochar and activated biochar represent around 83.8%, and 69.2% of the total removed amount at equilibrium, respectively. Then, a slower adsorption phase takes place, during which the adsorption rate gradually decreases and reaches an equilibrium state characterized by quasi-constant adsorbed amounts. For HYD220-0.5, the equilibrium is achieved after 3 h, and the corresponding amoxicillin adsorbed amount is 52.1 mg g−1. In contrast, for BIO500-0.5, the equilibrium is reached after 6 h, and the adsorbed amount at equilibrium is assessed to be 61.1 mg g−1. The higher adsorbed mass for BIO500-0.5 is attributed to its improved physico-chemical properties, especially its higher specific surface area and microporosity (see Table 3). These equilibrium durations are much lower than those observed for amoxicillin adsorption with a Ca-rich biochar (20 h) [34] and a post-treated sludge-derived biochar with Al, Fe, Fe or Mn (24 h) [52]. This finding represents an important advantage for full-scale application since energy expenses related to agitation will be significantly reduced.
Figure 5. Experimental and calculated kinetic data of amoxicillin removal by the activated hydrochar (a) and activated biochar (b).
Table 4 gives the PFO and PSO calculated parameters and indications for the experimental kinetic data’s correlation with the predicted data from these two models. Based on Table 4 and Figure 5, it can be deduced that, for both materials, the PSO model better fits the kinetic experimental data. Indeed, for both HYD-220-0.5 and BIO500-0.5, the PSO model exhibits higher R2 and lower APE values than the PFO model (Table 4). For instance, the PSO’s calculated MAPE for the activated hydrochar is evaluated to be 10.3%, which is almost 4.9 times lower than the calculated value for the PFO model. Moreover, compared to the PFO model, the calculated adsorbed masses at equilibrium for the PSO (qe,II) are closer to the experimental ones (Table 4). As expected, the amoxicillin adsorption rate constant (K2) of the activated biochar is lower than that of HYD-220-0.5 (Table 4). This finding proves that amoxicillin removal by the two olive stone-derived activated carbons involves chemical adsorption processes, possibly through hydrogen bonding, and electrostatic interactions between the amoxicillin molecules and the carbon surface groups. Similar findings were reported for amoxicillin removal by biochars derived from the pyrolysis of ZnCl2-modified sewage sludge [53] and an activated fore-modified bio-hydrochar of cornstalk [54].
Table 4. Parameters of PFO and PSO kinetic models for the adsorption of amoxicillin by the activated hydrochar and biochar from olive stones.

3.2.2. Impact of the Aqueous pH

The influence of the aqueous pH on the adsorption of amoxicillin onto the selected activated carbons BIO500-0.5 and HYD220-0.5 is studied for pH values ranging between 4 and 12. This large pH interval is selected since the electrical properties of both the activated carbons and the amoxicillin are highly dependent on the solutions’ pH values. For instance, amoxicillin has three pKa values depending onto its possible ionizable forms [55]: a pKa1 = 2.7 for carboxylic acid, a pKa2 = 7.5 for the primary amine group, and pKa3 = 9.63 for the hydroxyl group. Amoxicillin is positively charged for pH values lower than pKa1, zwitterionic (exists in two ionic forms amoxicillin±) for pH values between pKa1 and pKa2 and negatively charged for a pH higher than pKa3. Concerning our activated carbons, HYD220-0.5 and BIO500-0.5, they have a pHpzc of 7.96 and 8.07, respectively. This indicates that both materials will be positively charged for a large pH interval (lower than their pHpzc), and the adsorption of the negatively charged forms of amoxicillin will be favored. For pH values higher than around 8–8.1, our activated materials are negatively charged, which results in a decrease in amoxicillin removal (Figure 6). It is important to mention that the effect of the pH variation is more important for the activated hydrochar than the activated biochar. Indeed, the adsorbed amount of amoxicillin by HYD220-0.5 decreases from around 47.0 to less than 13.1 mg g−1 as the aqueous pH increases from 4 to 12. This is due to the electrostatic attraction of the negatively charged amoxicillin molecules with the positively charged material particles. Inversely, amoxicillin molecules are repulsed in highly alkaline media by negatively charged solid particles (Figure 6). According to the size of amoxicillin (1.24 nm) [56] at a pH range of 2.7–7.5, the molecule exists in its zwitterionic form (amoxicillin±), which facilitates its penetration into the microporous structure of the prepared activated carbons (physisorption). This result confirms that amoxicillin removal by both materials includes physical and chemical mechanisms. A similar behavior was reported for amoxicillin removal using a ZnCl2-activated biochar derived from ginger wastes, which exhibited an adsorption capacity of about 61.02 mg g−1 [57], and a magnetic tea waste hydrochar with a capacity of around 56.2 mg g−1 [58], indicating comparable adsorption performances with other engineered biochars reported in the literature.
Figure 6. Effect of initial aqueous pH on amoxicillin removal by the olive stone-derived activated hydrochar and activated biochar.

3.2.3. Adsorption Isotherm

The adsorption isotherm results for amoxicillin with the olive stone-derived activated carbons HYD220-0.5 and BIO500-0.5 are depicted in Figure 7. For both materials, the experimental amoxicillin adsorbed amounts increase with the increase in the initial concentration until a quasi-saturation status (Figure 7). Indeed, at an initial concentration of 10 mg L−1, the removed amoxicillin amount is evaluated as being 7.6 and 9.0 mg g−1 for HYD220-0.5 and BO500-0.5, respectively. When the initial amoxicillin concentration is increased to 800 mg L−1, these amounts increase by factors of 23.2 and 37.2, respectively. This finding is due to the increase in the amoxicillin gradient between the aqueous solution and the activated carbon particles.
Figure 7. Experimental and calculated isothermal data of amoxicillin removal by the olive stone-derived activated hydrochar (a) and activated biochar (b).
The results of the isotherm data fitting using Freundlich, Langmuir, and D-R models are given in Figure 7 and in Table 5. It can be clearly deduced that, for HYD-220-0.5, the isotherm experimental data are best fitted with the Langmuir model. Indeed, for this model, the calculated R2 is the highest (0.992), and the MAPE is the lowest (30.0%). This suggests that amoxicillin removal by HYD220-0.5 occurs on a monolayer at its surface with the presence of a finite number of energetically equivalent adsorption sites [52]. Moreover, amoxicillin removal by the activated hydrochar is favorable, as the calculated Langmuir’s constants ( R L = 1 1 + K L ∗ C 0 ) were lower than 1 (in the range of 0.14–0.96). However, for BIO-500-0.5, the Freundlich model appears to be the most suitable for the prediction of the experimental data, with the largest R2 and lowest MAPE (Table 5). This finding indicates that amoxicillin adsorption occurs heterogeneously and on multilayers on the activated biochar [59]. Furthermore, the amoxicillin removal process for this adsorbent is favorable since the corresponding Freundlich constant “n” is higher than 1 (Table 5). In addition, the fitting of the Langmuir model suggests that amoxicillin adsorption involves monolayer interactions. The mechanism may include hydrogen bonding, π–π interactions, and electrostatic attractions between amoxicillin and the carbon surface.
Table 5. Freundlich, Langmuir, and D-R isotherm adsorption parameters for amoxicillin removal by olive stone-derived activated hydrochar and activated biochar.
Regarding the D-R model, it exhibits the lowest ability to fit the experimental data for both materials, as it has relatively low R2 and high MAPE values (Table 5). Moreover, the corresponding adsorption capacities are much lower than the expected values (Figure 7 and Table 5). This may be due to the stringent hypotheses of this model, especially in the presence of the uniform and homogenous microporous structure in the activated carbons. In addition, for both activated carbons, the calculated free energy (E) of the D-R model is lower than 8.0 kJ mol−1 (Table 5), suggesting that amoxicillin removal may involve physical processes [55] (Table 6). A similar result was reported for amoxicillin removal by biochars derived from ginger wastes [57] and a mixture of date palm fronds, poultry manure and marble wastes [34].
The Langmuir’s adsorption capacities for HYD220-0.5 and BIO500-0.5 are evaluated to be 215.9 and 386.4 mg g−1, respectively. The higher adsorption capacity of the activated biochar compared to the activated hydrochar is due to its improved physico-chemical properties, and especially its higher microporosity and surface area. Indeed, BIO500-0.5 has a microporous volume and BET surface area of 0.241 cm3 g−1 and 625.2 m2 g−1, which are 21.1% and 19.7% larger than those observed for HYD220-0.5 (see Table 3). Moreover, both synthesized activated carbons can be considered as attractive materials for the removal of amoxicillin from aqueous solutions in comparison with activated chars derived from lignocllulosic biomasses, sewage sludge, and animal manure. For instance, the amoxicillin adsorption capacity of BIO500-0.5 is around 6.9, 2.2, 1.3, and 1.2 higher than a poultry manure-based biochar [34], ZnCl2-modified corn cobs [53], a KOH-modified sludge [60], and a CO2-activated biochar from date pits [61] (Table 6). However, other activated biochars exhibited a better adsorption ability than BIO500-0.5, such as a KOH-activated biochar from tannery hair waste [62] and a NaOH-activated biochar from guava seeds [55]. This is mainly due to their enhanced physicochemical properties (e.g., higher pore volume and BET surface area). Similar trends have been reported for adsorbents derived from rice straw [63] and sugarcane bagasse [64], reinforcing the influence of feedstock and activation method on the adsorption performance. For example, the latter activated biochar has a much higher pore volume (1.26 cm3 g−1) and BET surface area (2573.6 m2 g−1). The comparison of HYD220-0.5 efficiency with the scientific literature is not possible because, to the best of our knowledge, the current study is the first work on the use of activated hydrochars for amoxicillin removal from aqueous solutions. Nevertheless, HYD220-0.5 has a much better performance than a magnetic tea waste hydrochar produced through a microwave-assisted hydrothermal process, 7.4 mg g−1 [58], and ZnCl2-activated hydrochar from a pea shell (70.9 mg g−1) [65] and from a pinto bean peel (188.7 mg g−1) [65] (Table 6).
Table 6. Adsorption capacities of the prepared activated materials compared to the literature-reported adsorbents for amoxicillin removal (qm,L: Langmuir adsorption capacity; te: adsorption equilibrium time).

4. Conclusions

This study presents a comprehensive characterization of raw and CO2-activated hydrochars and biochars derived from olive stones and their application for amoxicillin removal from aqueous solutions under various experimental conditions. The results show that the used thermochemical conversion method significantly affects the characteristics of the generated carbonaceous materials. Indeed, contrary to the biochar, the hydrochar exhibits a smaller increase in carbon content due to milder conditions that retain more original carbon compounds. Moreover, both the raw hydrochar and biochar have low porosities and amorphous carbon microstructures, with the appearance of particles having spherical shapes for the hydrochar. The hydrochar shows more original functional groups than the biochar, confirming its less thermal decomposition. After CO2 activation, hydrochar particles are transformed into spherical shapes, and their BET surface area increases from 18.2 m2 g−1 to 846.7 m2 g−1. Meanwhile, the BET surface area of the biochar increases from 1.9 m2/g to 1349.3 m2 g−1, resulting in a more microporous structure. This important improvement of the textural properties of the activated biochar led to a large amoxicillin adsorption (386.4 mg g−1), which is 1.8 times higher than that of the activated hydrochar and 1.2 to 3.5 times more than those of some selected engineered biochars from the scientific literature. Nevertheless, it is worth noting that activated hydrochar has distinct advantages when considering practicality (use of wet biomass) and less energy consumption. Further research investigations are required to optimize these activated chars’ use as effective adsorbents for the treatment of actual pharmaceutical wastewater: in laboratory columns and CSTR mode, and then with pilot and large-scale dynamic setups. Finally, studies on the optimization of the regeneration step as well as the suitable treatment of the concentrated desorbing solution are highly recommended.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/pr14071064/s1, Text S1: Further details about the used analytical devices for the biochars and hydrochars characterization; Table S1: Kinetic and isotherm model equations used for the fitting of experimental data; Table S2: Raman spectral parameters of the olive stone-derived biochar and hydrochar and their activated forms; Figure S1: SEM images of the raw olive stones and their derived hydrochar and biochar; Figure S2: SEM images of the activated hydrochar and activated biochar derived from olive stones; Figure S3: Nitrogen adsorption–desorption isotherms at −196 °C for: (a) hydrochar, (b) biochar, (c) activated hydrochars and (d) activated biochars.

Author Contributions

Conceptualization, A.B., M.B. and E.B.K.; methodology, A.B., M.B., E.B.K., S.J. and M.J.; software, A.B.; validation, M.B., E.B.K., S.J. and M.J.; formal analysis, A.B. and M.B.; investigation, A.B., M.B. and E.B.K.; resources, M.B. and E.B.K.; data curation, M.B., E.B.K., S.J. and M.J.; writing—original draft preparation, A.B., M.B., E.B.K. and S.J.; writing—review and editing, M.J.; visualization, S.J. and M.J.; supervision, M.B. and E.B.K.; project administration, M.B. and E.B.K.; funding acquisition, M.B. and E.B.K. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the PHC France-Maghreb (Project No. 20MAG26).

Data Availability Statement

Data are available upon request.

Acknowledgments

The authors would like to thank the funding organization.

Conflicts of Interest

The authors declare no conflicts of interest. The PHC France-Maghreb had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

References

  1. Cimato, A.; Attilio, C. Worldwide diffusion and relevance of olive culture. In Olive Diseases and Disorders; Transworld Research NetWork: Trivandrum, India, 2011; pp. 1–21. [Google Scholar]
  2. IOC. International Olive Council 2024. Available online: https://www.internationaloliveoil.org/ (accessed on 26 February 2026).
  3. Di Giacomo, G.; Romano, P. Evolution of the olive oil industry along the entire production chain and related waste management. Energies 2022, 15, 465. [Google Scholar] [CrossRef] [Scilit]
  4. Marks, E.A.N.; Kinigopoulou, V.; Akrout, H.; Azzaz, A.A.; Doulgeris, C.; Jellali, S.; Rad, C.; Sánchez Zulueta, P.; Tziritis, E.; El-Bassi, L.; et al. Potential for production of biochar-based fertilizers from olive mill waste in Mediterranean Basin countries: An initial assessment for Spain, Tunisia, and Greece. Sustainability 2020, 12, 6081. [Google Scholar] [CrossRef] [Scilit]
  5. Enaime, G.; Dababat, S.; Wichern, M.; Lübken, M. Olive mill wastes: From wastes to resources. Environ. Sci. Pollut. Res. 2024, 31, 20853–20880. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  6. Haddad, K.; Jeguirim, M.; Jellali, S.; Thevenin, N.; Ruidavets, L.; Limousy, L. Biochar production from Cypress sawdust and olive mill wastewater: Agronomic approach. Sci. Total Environ. 2021, 752, 141713. [Google Scholar] [CrossRef] [Scilit]
  7. Sert, M.; Selvi Gökkaya, D.; Cengiz, N.; Ballice, L.; Yüksel, M.; Sağlam, M. Hydrogen production from olive-pomace by catalytic hydrothermal gasification. J. Taiwan Inst. Chem. Eng. 2018, 83, 90–98. [Google Scholar] [CrossRef] [Scilit]
  8. Bourafa, A.; Berrich, E.; Belhachemi, M.; Jellali, S.; Jeguirim, M. Preparation and characterization of hydrochars and CO2-activated hydrochars from date and olive stones. Biomass Convers. Biorefin. 2023, 14, 20385–20396. [Google Scholar] [CrossRef] [Scilit]
  9. Diaz, E.; Sanchis, I.; Coronella, C.J.; Mohedano, A.F. Activated Carbons from Hydrothermal Carbonization and Chemical Activation of Olive Stones: Application in Sulfamethoxazole Adsorption. Resources 2022, 11, 43. [Google Scholar] [CrossRef] [Scilit]
  10. Fadhil, A.B.; Kareem, B.A. Co-pyrolysis of mixed date pits and olive stones: Identification of bio-oil and the production of activated carbon from bio-char. J. Anal. Appl. Pyrolysis 2021, 158, 105249. [Google Scholar] [CrossRef] [Scilit]
  11. Yu, S.; He, J.; Zhang, Z.; Sun, Z.; Xie, M.; Xu, Y.; Bie, X.; Li, Q.; Zhang, Y.; Sevilla, M.; et al. Towards Negative Emissions: Hydrothermal Carbonization of Biomass for Sustainable Carbon Materials. Adv. Mater. 2024, 36, 2307412. [Google Scholar] [CrossRef] [Scilit]
  12. Masoumi, S.; Borugadda, V.B.; Nanda, S.; Dalai, A.K.; Bartocci, P.; Taghavi, S. Hydrochar: A Review on Its Production Technologies and Applications. Catalysts 2021, 11, 939. [Google Scholar] [CrossRef] [Scilit]
  13. Ravindiran, G.; Rajamanickam, S.; Janardhan, G.; Hayder, G.; Alagumalai, A.; Mahian, O.; Lam, S.S.; Sonne, C. Production and modifications of biochar to engineered materials and its application for environmental sustainability: A review. Biochar 2024, 6, 62. [Google Scholar] [CrossRef] [Scilit]
  14. Kambo, H.S.; Dutta, A. A comparative review of biochar and hydrochar in terms of production, physico-chemical properties and applications. Renew. Sustain. Energy Rev. 2015, 45, 359–378. [Google Scholar] [CrossRef] [Scilit]
  15. Azzaz, A.A.; Ghimbeu, C.M.; Jellai, S.; El-Bassi, L.; Jeguirim, M. Olive Mill by-Products Thermochemical Conversion via Hydrothermal Carbonization and Slow Pyrolysis: Detailed Comparison between the Generated Hydrochars and Biochars Characteristics. Processes 2022, 10, 231. [Google Scholar] [CrossRef] [Scilit]
  16. Marcińczyk, M.; Oleszczuk, P. Biochar and engineered biochar as slow-and controlled-release fertilizers. J. Clean. Prod. 2022, 339, 130685. [Google Scholar] [CrossRef] [Scilit]
  17. Haddad, K.; Jeguirim, M.; Jerbi, B.; Chouchene, A.; Dutournié, P.; Thevenin, N.; Ruidavets, L.; Jellali, S.; Limousy, L. Olive mill wastewater: From a pollutant to green fuels, agricultural water source and biofertilizer. ACS Sustain. Chem. Eng. 2017, 5, 8988–8996. [Google Scholar] [CrossRef] [Scilit]
  18. Wang, F.; Xiang, L.; Sze-Yin Leung, K.; Elsner, M.; Zhang, Y.; Guo, Y.; Pan, B.; Sun, H.; An, T.; Ying, G.; et al. Emerging contaminants: A One Health perspective. Innovation 2024, 5, 100612. [Google Scholar] [CrossRef] [Scilit]
  19. Sumpter, J.P.; Johnson, A.C.; Runnalls, T.J. Pharmaceuticals in the Aquatic Environment: No Answers Yet to the Major Questions. Environ. Toxicol. Chem. 2024, 43, 589–594. [Google Scholar] [CrossRef] [Scilit]
  20. Litskas, V.D.; Karamanlis, X.N.; Prousali, S.P.; Koveos, D.S. Effects of the Antibiotic Amoxicillin on Key Species of the Terrestrial Environment. Bull. Environ. Contam. Toxicol. 2018, 100, 509–515. [Google Scholar] [CrossRef] [Scilit]
  21. Kovalakova, P.; Cizmas, L.; McDonald, T.J.; Marsalek, B.; Feng, M.; Sharma, V.K. Occurrence and toxicity of antibiotics in the aquatic environment: A review. Chemosphere 2020, 251, 126351. [Google Scholar] [CrossRef] [Scilit]
  22. Nasir, A.; Saleh, M.; Aminzai, M.T.; Alary, R.; Dizge, N.; Yabalak, E. Adverse effects of veterinary drugs, removal processes and mechanisms: A review. J. Environ. Chem. Eng. 2024, 12, 111880. [Google Scholar] [CrossRef] [Scilit]
  23. Hama Aziz, K.H.; Mustafa, F.S.; Hassan, M.A.; Omer, K.M.; Hama, S. Biochar as green adsorbents for pharmaceutical pollution in aquatic environments: A review. Desalination 2024, 583, 117725. [Google Scholar] [CrossRef] [Scilit]
  24. Prochnow, F.D.; Cavali, M.; Dresch, A.P.; Belli, I.M.; Libardi, N.J.; de Castilhos, A.B.J. Biochar: From Laboratory to Industry Scale—An Overview of Scientific and Industrial Advances, Opportunities in the Brazilian Context, and Contributions to Sustainable Development. Processes 2024, 12, 1006. [Google Scholar] [CrossRef] [Scilit]
  25. Nand, S.; Prakash, P.; Verma, S.; Mishra, S.; Patel, A. Biochar for mitigating pharmaceutical pollution in wastewater: A sustainable solution. Sci. Total Environ. 2025, 966, 178743. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  26. Vu, T.M.; Phuong, M.; Van, H. Biomass-derived hydrochar and activated carbon in pharmaceutical pollution mitigation: A comprehensive overview. RSC Adv. 2025, 15, 43053–43084. [Google Scholar] [CrossRef] [Scilit]
  27. Hagos, F.M.; Qian, H.; Di, J.; Shan, S.; Yang, R.; Li, Y.; Gai, X. Rice Husk Hydrochars Prepared with Different Post-treatment Methods for the Adsorption of Dyes and Antibiotics. BioResources 2022, 17, 725–749. [Google Scholar] [CrossRef] [Scilit]
  28. Delgado-Moreno, L.; Bazhari, S.; Gasco, G.; Méndez, A.; El Azzouzi, M.; Romero, E. New insights into the efficient removal of emerging contaminants by biochars and hydrochars derived from olive oil wastes. Sci. Total Environ. 2021, 752, 141838. [Google Scholar] [CrossRef] [Scilit]
  29. Belhachemi, M. Adsorption of organic compounds on activated carbons. In Sorbents Materials for Controlling Environmental Pollution; Current State and Trends; Elsevier: Amsterdam, The Netherlands, 2021; pp. 355–385. [Google Scholar] [CrossRef] [Scilit]
  30. Prauchner, M.J.; Rodríguez-Reinoso, F. Chemical versus physical activation of coconut shell: A comparative study. Microporous Mesoporous Mater. 2012, 152, 163–171. [Google Scholar] [CrossRef] [Scilit]
  31. Al-sareji, O.J.; Grmasha, R.A.; Meiczinger, M.; Al-Juboori, R.A.; Somogyi, V.; Stenger-Kovács, C.; Hashim, K.S. A sustainable and highly efficient fossil-free carbon from olive stones for emerging contaminants removal from different water matrices. Chemosphere 2024, 351, 141189. [Google Scholar] [CrossRef] [Scilit]
  32. Späth, J.; Arumugam, P.; Lindberg, R.H.; Abafe, O.A.; Jansson, S.; Fick, J.; Buckley, C.A. Biochar for the removal of detected micropollutants in south african domestic wastewater: A case study from a demonstration-scale decentralised wastewater treatment system in ethekwini. Water SA 2021, 47, 396–416. [Google Scholar] [CrossRef] [Scilit]
  33. Shulin, P.; Tahri, W.; Khaskhoussi, A.; El-Sappah, A.H. Enhanced water treatment via combined oxidation and adsorption: A synergistic approach. Front. Chem. 2026, 13, 1747407. [Google Scholar] [CrossRef] [Scilit]
  34. Jellali, S.; Hamdi, W.; Al-Harrasi, M.; Al-Wardy, M.; Al-Sabahi, J.; Al-Nadabi, H.; Al-Raeesi, A.; Jeguirim, M. Investigations on amoxicillin removal from aqueous solutions by novel calcium-rich biochars: Adsorption properties and mechanisms exploration. Processes 2024, 12, 1552. [Google Scholar] [CrossRef] [Scilit]
  35. Sevilla, M.; Maciá-Agulló, J.A.; Fuertes, A.B. Hydrothermal carbonization of biomass as a route for the sequestration of CO2: Chemical and structural properties of the carbonized products. Biomass Bioenergy 2011, 35, 3152–3159. [Google Scholar] [CrossRef] [Scilit]
  36. Funke, A.; Ziegler, F. Hydrothermal carbonization of biomass: A summary and discussion of chemical mechanisms for process engineering. Biofuels Bioprod. Biorefin. 2010, 4, 160–177. [Google Scholar] [CrossRef] [Scilit]
  37. Román, S.; Nabais, J.M.V.; Laginhas, C.; Ledesma, B.; González, J.F. Hydrothermal carbonization as an effective way of densifying the energy content of biomass. Fuel Process. Technol. 2012, 103, 78–83. [Google Scholar] [CrossRef] [Scilit]
  38. Hernandez-Mena, L.E.; Pécora, A.A.B.; Beraldo, A.L. Slow Pyrolysis of Bamboo Biomass: Analysis of Biochar Properties. Chem. Eng. Trans. 2014, 37, 115–120. [Google Scholar] [CrossRef] [Scilit]
  39. Bedoui, A.; Souissi-Najar, S.; Shawalliah, I.S.; Norzah, A.; Ouederni, A. Investigation of olive stones pyrolysis via coupled thermogravimetric analysis- mass spectrometry: Thermal behavior and kinetic parameters. Cell. Chem. Technol. 2022, 56, 481–494. [Google Scholar] [CrossRef] [Scilit]
  40. Ma, Z.; Chen, D.; Gu, J.; Bao, B.; Zhang, Q. Determination of pyrolysis characteristics and kinetics of palm kernel shell using TGA–FTIR and model-free integral methods. Energy Convers. Manag. 2015, 89, 251–259. [Google Scholar] [CrossRef] [Scilit]
  41. Yu, X.; Liu, S.; Lin, G.; Yang, Y.; Zhang, S.; Zhao, H.; Zheng, C.; Gao, X. KOH-activated hydrochar with engineered porosity as sustainable adsorbent for volatile organic compounds. Colloids Surf. A Physicochem. Eng. Asp. 2020, 588, 124372. [Google Scholar] [CrossRef] [Scilit]
  42. Belhachemi, M.; Rios, R.V.R.A.; Addoun, F.; Silvestre-Albero, J.; Sepúlveda-Escribano, A.; Rodríguez-Reinoso, F. Preparation of activated carbon from date pits: Effect of the activation agent and liquid phase oxidation. J. Anal. Appl. Pyrolysis 2009, 86, 168–172. [Google Scholar] [CrossRef] [Scilit]
  43. Kumbhar, D.; Palliyarayil, A.; Reghu, D.; Shrungar, D.; Umapathy, S.; Sil, S. Rapid discrimination of porous bio-carbon derived from nitrogen rich biomass using Raman spectroscopy and arti fi cial intelligence methods. Carbon 2021, 178, 792–802. [Google Scholar] [CrossRef] [Scilit]
  44. Braghiroli, F.L.; Fierro, V.; Parmentier, J.; Vidal, L.; Gadonneix, P.; Celzard, A. Hydrothermal carbons produced from tannin by modification of the reaction medium: Addition of H+ and Ag+. Ind. Crops Prod. 2015, 77, 364–374. [Google Scholar] [CrossRef] [Scilit]
  45. Yu, J.; Sun, L.; Berrueco, C.; Fidalgo, B.; Paterson, N.; Millan, M. Influence of temperature and particle size on structural characteristics of chars from Beechwood pyrolysis. J. Anal. Appl. Pyrolysis 2018, 130, 249–255. [Google Scholar] [CrossRef] [Scilit]
  46. Ghosh, A.; da Silva Santos, A.M.; Cunha, J.R.; Dasgupta, A.; Fujisawa, K.; Ferreira, O.P.; Lobo, A.O.; Terrones, M.; Terrones, H.; Viana, B.C. CO2 Sensing by in-situ Raman spectroscopy using activated carbon generated from mesocarp of babassu coconut. Vib. Spectrosc. 2018, 98, 111–118. [Google Scholar] [CrossRef] [Scilit]
  47. Belhachemi, M.; Khiari, B.; Jeguirim, M.; Sepúlveda-Escribano, A. Characterization of biomass-derived chars. In Char and Carbon Materials Derived from Biomass; Production, Characterization and Applications; Elsevier: Amsterdam, The Netherlands, 2019; pp. 69–108. [Google Scholar] [CrossRef] [Scilit]
  48. Zhang, L.; Liu, S.; Wang, B.; Wang, Q.; Yang, G. Effect of Residence Time on Hydrothermal Carbonization of Corn Cob Residual. BioResources 2015, 10, 3979–3986. [Google Scholar] [CrossRef] [Scilit]
  49. Sevilla, M.; Fuertes, A.B. The production of carbon materials by hydrothermal carbonization of cellulose. Carbon 2009, 47, 2281–2289. [Google Scholar] [CrossRef] [Scilit]
  50. Ahmad, S.; Zhu, X.; Wei, X.; Zhang, S. Characterization and Potential Applications of Hydrochars Derived from P-and N-Enriched Agricultural and Antibiotic Residues via Microwave-Assisted Hydrothermal Conversion. Energy Fuels 2020, 34, 11154–11164. [Google Scholar] [CrossRef] [Scilit]
  51. Budai, A.; Calucci, L.; Rasse, D.P.; Strand, L.T.; Pengerud, A.; Wiedemeier, D.; Abiven, S.; Forte, C. Effects of pyrolysis conditions on Miscanthus and corncob chars: Characterization by IR, solid state NMR and BPCA analysis. J. Anal. Appl. Pyrolysis 2017, 128, 335–345. [Google Scholar] [CrossRef] [Scilit]
  52. Fan, X.; Qian, Z.; Liu, J.; Geng, N.; Hou, J.; Li, D. Investigation on the adsorption of antibiotics from water by metal loaded sewage sludge biochar. Water Sci. Technol. 2021, 83, 739–750. [Google Scholar] [CrossRef] [Scilit]
  53. Varela, C.F.; Moreno-Aldana, L.C.; Agámez-Pertuz, Y.Y. Adsorption of pharmaceutical pollutants on ZnCl2-activated biochar from corn cob: Efficiency, selectivity and mechanism. J. Bioresour. Bioprod. 2024, 9, 58–73. [Google Scholar] [CrossRef] [Scilit]
  54. Li, H.; Hu, J.; Cao, Y.; Li, X.; Wang, X. Development and assessment of a functional activated fore-modified bio-hydrochar for amoxicillin removal. Bioresour. Technol. 2017, 246, 168–175. [Google Scholar] [CrossRef] [Scilit]
  55. Pezoti, O.; Cazetta, A.L.; Bedin, K.C.; Souza, L.S.; Martins, A.C.; Silva, T.L.; Santos Júnior, O.O.; Visentainer, J.V.; Almeida, V.C. NaOH-activated carbon of high surface area produced from guava seeds as a high-efficiency adsorbent for amoxicillin removal: Kinetic, isotherm and thermodynamic studies. Chem. Eng. J. 2016, 288, 778–788. [Google Scholar] [CrossRef] [Scilit]
  56. Noguera-oviedo, K.; Aga, D.S. Lessons learned from more than two decades of research on emerging contaminants in the environment. J. Hazard. Mater. 2016, 316, 242–251. [Google Scholar] [CrossRef] [Scilit]
  57. Meghani, R.; Lahane, V.; Kotian, S.Y.; Lata, S.; Tripathi, S.; Ansari, K.M.; Yadav, A.K. Valorization of Ginger Waste-Derived Biochar for Simultaneous Multiclass Antibiotics Remediation in Aqueous Medium. ACS Omega 2023, 8, 11065–11075. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  58. Shahavi, M.H.; Akbari, M.; Ayrilmis, N.; Dorieh, A. A Sustainable Nanoporous Adsorbent for Reducing Amoxicillin in Pharmaceutical Wastewater: Magnetic Tea Waste Hydrochar. ChemistrySelect 2024, 9, e202404915. [Google Scholar] [CrossRef] [Scilit]
  59. Choi, S.W.; Hong, J.; Youn, S.; Kim, I. Removal of amoxicillin by coffee grounds biochar with different pretreatment methods. Environ. Adv. 2023, 14, 100446. [Google Scholar] [CrossRef] [Scilit]
  60. Simões Dos Reis, G.; Bergna, D.; Tuomikoski, S.; Grimm, A.; Lima, E.C.; Thyrel, M.; Skoglund, N.; Lassi, U.; Larsson, S.H. Preparation and Characterization of Pulp and Paper Mill Sludge-Activated Biochars Using Alkaline Activation: A Box-Behnken Design Approach. ACS Omega 2022, 7, 32620–32630. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  61. Belhachemi, M.; Djelaila, S. Removal of Amoxicillin Antibiotic from Aqueous Solutions by Date Pits Activated Carbons. Environ. Process. 2017, 4, 549–561. [Google Scholar] [CrossRef] [Scilit]
  62. Herrera, K.; Morales, L.F.; López, J.E.; Montoya-Ruiz, C.; Muñoz, S.; Zapata, D.; Saldarriaga, J.F. Biochar production from tannery waste pyrolysis as a circular economy strategy for the removal of emerging compounds in polluted waters. Biomass Convers. Biorefin. 2024, 14, 22867–22880. [Google Scholar] [CrossRef] [Scilit]
  63. Fan, W.; Cheng, L.; Fu, W.; Liu, J.; Jiang, G.; Ao, L. Rice-straw-derived porous biochar with low spatial polarity for efficient adsorptive removal of antibiotics in surface water. J. Water Process Eng. 2025, 73, 107715. [Google Scholar] [CrossRef] [Scilit]
  64. Prasannamedha, G.; Kumar, P.S.; Mehala, R.; Sharumitha, T.J.; Surendhar, D. Enhanced adsorptive removal of sulfamethoxazole from water using biochar derived from hydrothermal carbonization of sugarcane bagasse. J. Hazard. Mater. 2021, 407, 124825. [Google Scholar] [CrossRef] [Scilit]
  65. Kantarli, I.C. Investigation of Use of Hydrochars Obtained From Legume Wastes as Fuel and Their Conversion into Activated Carbon for Amoxicillin Removal. Black Sea J. Eng. Sci. 2023, 6, 486–501. [Google Scholar] [CrossRef] [Scilit]
  66. Jellali, S.; Khiari, B.; Al-Harrasi, M.; Charabi, Y.; Al-Sabahi, J.; Al-Abri, M.; Usman, M.; Al-Raeesi, A.; Jeguirim, M. Industrial sludge conversion into biochar and reuse in the context of circular economy: Impact of pre-modification processes on pharmaceuticals removal from aqueous solutions. Sustain. Chem. Pharm. 2023, 33, 101114. [Google Scholar] [CrossRef] [Scilit]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Article Metrics

Citations

Article Access Statistics

Multiple requests from the same IP address are counted as one view.