Influence of Inter-Particle Bonding on Compression Performance of Porous Mo Deposited by Flame Spraying of Semi-Molten Particles
Abstract
:1. Introduction
2. Experimental Procedures
2.1. Preparation of Porous Mo Deposits
2.2. Heat Treatment of Porous Mo
2.3. Characterization Methods
3. Results and Discussion
3.1. Morphology and Inter-Particle Bonding of As-sprayed Porous Mo Deposits
3.2. Effect of Reduction on Inter-Particle Bonding of Porous Mo Deposits
3.3. Effect of Sintering on Inter-Particle Bonding of Porous Mo Deposits
3.4. Compression Properties of Porous Mo Deposits
3.4.1. Compression Properties of As-sprayed Porous Mo Deposits
3.4.2. Influence of Reduction on Compression Properties of Porous Mo Deposits
3.4.3. Influence of Sintering on Compression Properties of Porous Mo Deposits
4. Conclusions
Author Contributions
Funding
Acknowledgments
Conflicts of Interest
References
- Zhao, B.; Yu, T.Y.; Ding, W.F.; Zhang, L.C.; Su, H.H.; Chen, Z.Z. Effect of micropores on the microstructure and mechanical properties of porous Cu-Sn-Ti composites. Mater. Sci. Eng. A 2018, 730, 345–354. [Google Scholar] [CrossRef]
- Li, B.Q.; Wang, C.Y.; Lu, X. Effect of pore structure on the compressive property of porous Ti produced by powder metallurgy technique. Mater. Des. 2013, 50, 613–619. [Google Scholar] [CrossRef]
- Cao, Y.J.; Shen, W.Q.; Shao, J.F.; Burlion, N. Influences of micro-pores and meso-pores on elastic and plastic properties of porous materials. Eur. J. Mech. A. Solids 2018, 72, 407–423. [Google Scholar] [CrossRef]
- Okulov, I.V.; Volegov, A.S.; Markmann, J. Tuning microstructure and mechanical properties of open porous TiNb and TiFe alloys by optimization of dealloying parameters. Scr. Mater. 2018, 154, 68–72. [Google Scholar] [CrossRef]
- Segurado, J.; Parteder, E.; Plankensteiner, A.F.; Bohm, H.J. Micromechanical studies of the densification of porous molybdenum. Mater. Sci. Eng. A 2002, 333, 270–278. [Google Scholar] [CrossRef]
- Jaworski, M.A.; Lau, C.Y.; Urbansky, D.L.; Malfa, M.B.; Gray, T.K.; Neumann, M.J.; Ruzic, D.N. Observations of liquid lithium uptake in a porous molybdenum foam. J. Nucl. Mater. 2008, 378, 105–109. [Google Scholar] [CrossRef]
- Narayanasamy, R.; Ponalagusamy, R.; Subramanian, K.R. Generalised yield criteria of porous sintered powder metallurgy metals. J. Mater. Process. Technol. 2001, 110, 182–185. [Google Scholar] [CrossRef]
- Yao, J.T.; Li, C.J.; Li, Y.; Chen, B.; Huo, H.B. Relationships between the properties and microstructure of Mo–Cu composites prepared by infiltrating copper into flame-sprayed porous Mo skeleton. Mater. Des. 2015, 88, 774–780. [Google Scholar] [CrossRef]
- Yao, J.T.; Yang, G.J.; Li, C.X.; Li, C.J. Fabrication of porous stainless steel by flame spraying of semimolten particles. Mater. Manuf. Process. 2014, 29, 1253–1259. [Google Scholar] [CrossRef]
- Bai, C.Y.; Colombo, P. Processing, properties and applications of highly porous geopolymers: A review. Ceram. Int. 2018, 44, 16103–16118. [Google Scholar] [CrossRef]
- Qin, J.H.; Chen, Q.; Yang, C.Y.; Huang, Y. Research process on property and application of metal porous materials. J. Alloy. Compd. 2016, 654, 39–44. [Google Scholar] [CrossRef]
- Yiatros, S.; Marangos, O.; Votsis, R.A.; Brennan, F.P. Compressive properties of granular foams of adhesively bonded steel hollow sphere blocks. Mech. Res. Commun. 2018, 94, 13–20. [Google Scholar] [CrossRef]
- Zhou, W.; Tang, Y.; Liu, B.; Song, R.; Jiang, L.L.; Hui, K.S.; Hui, K.N.; Yao, H.M. Compressive properties of porous metal fiber sintered sheet produced by solid-state sintering process. Mater. Des. 2012, 35, 414–418. [Google Scholar] [CrossRef]
- Li, F.; Li, J.; Xu, G.; Liu, G.; Kou, H.; Zhou, L. Fabrication, pore structure and compressive behavior of anisotropic porous titanium for human trabecular bone implant applications. J. Mech. Behav. Biomed. Mater. 2015, 46, 104–114. [Google Scholar] [CrossRef] [PubMed]
- Liu, J.A.; Shi, S.Q.; Zheng, Z.B.; Huang, K.; Yan, Y.Y. Characterization and compressive properties of Ni/Mg hybrid foams. Mater. Sci. Eng. A. 2017, 708, 329–335. [Google Scholar] [CrossRef]
- Liu, Y.J.; Wang, H.L.; Li, S.J.; Wang, S.G.; Wang, W.J.; Hou, W.T.; Hao, Y.L.; Yang, R.; Zhang, L.C. Compressive and fatigue behavior of beta-type titanium porous structures fabricated by electron beam melting. Acta Mater. 2017, 126, 58–66. [Google Scholar] [CrossRef]
- Qiao, J.C.; Xi, Z.P.; Tang, H.P.; Wang, J.Y.; Zhu, J.L. Influence of porosity on quasi-static compressive properties of porous metal media fabricated by stainless steel fibers. Mater. Des. 2009, 30, 2737–2740. [Google Scholar] [CrossRef]
- Zou, C.M.; Liu, Y.; Yang, X.; Wang, H.W.; Wei, Z.J. Effect of sintering neck on compressive mechanical properties of porous titanium. Trans. Nonferr. Met. Soc. China 2012, 22, 485–490. [Google Scholar] [CrossRef]
- Gu, D.D.; Shen, Y.F. Processing conditions and microstructural features of porous 316L stainless steel components by DMLS. Appl. Surf. Sci. 2008, 255, 1880–1887. [Google Scholar] [CrossRef]
- Takata, N.; Uematsu, K.; Kobashi, M. Compressive properties of porous Ti–Al alloys fabricated by reaction synthesis using a space holder powder. Mater. Sci. Eng. A. 2017, 697, 66–70. [Google Scholar] [CrossRef]
- Vesenjak, M.; Kovačič, A.; Tane, M.; Borovinšek, M.; Nakajima, H.; Ren, Z. Compressive properties of lotus-type porous iron. Comput. Mater. Sci. 2012, 65, 37–43. [Google Scholar] [CrossRef]
- Lin, J.G.; Li, Y.C.; Wong, C.S.; Hodgson, P.D.; Wen, C.E. Degradation of the strength of porous titanium after alkali and heat treatment. J. Alloy. Compd. 2009, 485, 316–319. [Google Scholar] [CrossRef]
- Salahinejad, E.; Amini, R.; Marasi, M.; Hadianfard, M.J. The effect of sintering time on the densification and mechanical properties of a mechanically alloyed Cr–Mn–N stainless steel. Mater. Des. 2010, 31, 527–532. [Google Scholar] [CrossRef]
- Chen, B.; Li, C.J.; Yang, G.J.; Yao, J.T.; Huo, H.B.; Li, C.X. Fabrication of porous molybdenum by controlling spray particle state. J. Therm. Spray Technol. 2012, 21, 1032–1045. [Google Scholar] [CrossRef]
- Yao, J.T.; Ren, J.Q.; Hui, B.H.; Yang, G.J.; Li, C.X.; Li, C.J. Deposition behavior of semi-molten spray particles during flame spraying of porous metal alloy. J. Therm. Spray Technol. 2014, 23, 991–999. [Google Scholar] [CrossRef]
Point | Elemental Composition (wt.%) | |
---|---|---|
Mo | O | |
Point 1 | 100.00 | – |
Point 2 | 63.29 | 36.71 |
Point 3 | 76.63 | 23.37 |
© 2019 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).
Share and Cite
Yao, J.; Dong, H.; Li, Y.; Li, X. Influence of Inter-Particle Bonding on Compression Performance of Porous Mo Deposited by Flame Spraying of Semi-Molten Particles. Coatings 2019, 9, 158. https://doi.org/10.3390/coatings9030158
Yao J, Dong H, Li Y, Li X. Influence of Inter-Particle Bonding on Compression Performance of Porous Mo Deposited by Flame Spraying of Semi-Molten Particles. Coatings. 2019; 9(3):158. https://doi.org/10.3390/coatings9030158
Chicago/Turabian StyleYao, Jiantao, Hui Dong, Yan Li, and Xiao Li. 2019. "Influence of Inter-Particle Bonding on Compression Performance of Porous Mo Deposited by Flame Spraying of Semi-Molten Particles" Coatings 9, no. 3: 158. https://doi.org/10.3390/coatings9030158