1. Introduction
With the increasingly severe maritime security situation, all countries are actively strengthening their maritime defense forces to defend their sovereignty, independence and territorial integrity. As an important part of naval equipment, submarine projectiles have the advantages of good concealment and high lethality, whose underwater launch technology is one of the key technologies to enhance our country’s future combat capabilities. At present, only a few countries in the world have relatively mature underwater launch technology of submarine projectiles.
Unsteady cavitation research has been the difficulty of underwater vertical launch, as the complex flow field involving multiphase coupling makes it hard to analyze the dynamic characteristics of projectiles. The evolution process of the cavitation from growth, shedding to collapse affects the motion stability of projectiles, and even damages the surface and performance of projectiles [
1]. Therefore, further study on the mechanism and influence of the unsteady cavitation will have great significance to the optimization of the projectile’s design and the development of underwater launch technology.
The early cavitation flow theory [
2,
3] has many limitations, which makes it difficult to solve unsteady cavitation problems, while the cavitation collapse theory [
4,
5] is limited to the single bubble model as well. The current research mainly relies on simulations and experiments, especially in hydrofoil cavitation, which is relatively mature. By modifying the simulation model [
6] and improving the experimental observation technology, combined with mechanical analysis [
7], great achievements have been made in cavitation mechanism, morphological definition and stability investigation. Kubota et al. [
8] and Le et al. [
9] experimentally analyzed the unsteady cavitation evolution of the hydrofoil and pointed out that the cavitation stability is related to the influence of the jet and vortex. Kjeldsen et al. [
10] and Wang et al. [
11] made experimental observations and three-dimensional simulations on the cavitation characteristics of NACA0015 hydrofoils with LDV (Laser Doppler Velocimetry) and LES (Large Eddy Simulation), studied the influence of the angle of attack and cavitation number on sheet and cloud cavitation. Huang et al. [
12] analyzed the periodic cavitation evolution of Clark-Y hydrofoil based on the water tunnel test with PIV (Particle Image Velocimetry), and discussed the relationship between cavitation instability and vorticity. The research conclusions on hydrofoil cavitation provides a theoretical basis for the discussion on projectile’s unsteady cavitation characteristics.
The cavitation circumfluence of horizontally launched projectiles is similar to that of hydrofoils, but the noise characteristics are still different [
13]. While investigating the cavitation stability, the related literatures also summarize the influence of head shape, cavitation number, speed and angle of attack on cavitation and dynamic characteristics. Yu et al. [
14] studied the correlation between cavitation shedding and re-entry jet through SHPB (Split-Hopkinson pressure bar) test and LES simulation. Wei et al. [
15] and Hu et al. [
16] discussed the evolution differences of the cavitation shape and vortex structure under various head shapes with PIV and dynamic force measurement. Chen et al. [
17] and Wan et al. [
18] analyzed the change of cavitation collapse pressure during the deceleration process and the inhibitory of increasing the angle of attack on the sheet cavitation shedding simulatively. Zhao et al. [
19] observed the cavitation development and projectile’s movement at different speeds with high-speed cameras. Sun et al. [
20] described the bubble evolution under different cavitation numbers and obtained the time-frequency characteristics of the pressure pulsation with closed-loop water tunnels and sampling systems.
There is gravity in the underwater vertical launch, involving complex cavitation collapse problems. The related results mostly rely on numerical simulation [
21,
22], while experimental research is rare. You et al. [
23] simulated the cavitation collapse out of water and illustrated the effect of the impact pressure on the structure considering the fluid-structure interaction. Zhang et al. [
24] and Liu et al. [
25] analyzed the cavitation shape and pressure changes at different speeds and depths and their effects on the projectile’s motion simulatively. Cao et al. [
26] simulated the evolution of tail cavitation and discussed the causes of cavitation fluctuations and their interference with movement. Wang et al. [
27,
28] numerically and experimentally illustrated the relationship between cavitation shedding and re-entry jet, studied the mechanism of cavitation collapse and analyzed the effects of cross flow and deceleration on the cavitation characteristics. Chen et al. [
29] simulated the cavitation development process and analyzed the influence of the angle of attack on the cavitation shedding and collapse with LES. Quan et al. [
30] recorded the cavity shape and collapse pressure with high-speed cameras and pressure sensors, and found that the pressure pulse moves from the collapse point along the surface to the tail of projectiles, whose value is closely related to the bubble shape. Fu et al. [
31] discussed the influence of launch speed and depth on bubble shape and projectile’s posture through scaled model experiments. Song et al. [
32] conducted water-exit tests on objects of various shapes and pointed out that velocity is the main parameter causing the deformation of the free liquid surface.
In summary, certain results have been achieved in the research on the cavitation stability of hydrofoils and projectiles. However, most of the tests were carried out in water tunnels, without considering the effect of gravity, which makes it difficult to discuss the problem of the water-exit cavitation collapse. Therefore, based on a self-designed underwater launch platform, this paper studies the cavitation evolution and projectile movement under different head forms and launch speeds during a scaled model vertical launch test to provide technical support for load analysis and structural design of submarine projectiles and provide theoretical references for the development of underwater launch technology in our country. The structure of this paper is as follows:
Section 2 introduces the experimental platform and model in detail. Subsequently,
Section 3 analyzes the causes of unsteady cavitation, investigates the effect of head forms with launch speeds on cavitation process through the experimental results and discusses the movement characteristics of underwater projectiles as well. Finally, the main conclusions are summarized in
Section 4.
2. Experimental Platform and Model
The underwater launch platform consists of four parts: pneumatic launch system, control system, image acquisition system and protective recovery system, as shown in
Figure 1. The test uses cold emission, in which the water tank size is 1.84 m × 1.2 m × 1.22 m and the water depth is about 0.8 m. The pneumatic launch system is composed of an air compressor, a gas cylinder, a launch tube, an aluminum guide rail, etc. The air compressor provides gas to launch projectiles and changes supply gas flow to adjust the launch speed.
The control system includes solenoid valves, laser switches, geared motors, and control circuits. During the test, two couples of laser switches are used as the trigger switch of control circuits and the anti-collision limit switch of the launch platform. The geared motor is started by control circuits to provide power for the launch platform and make its movement controllable along the guide, while the parameters are set on the control panel to achieve the ideal launch situation. The image acquisition system relies on SM-HS4M1K and Phantom high-speed cameras whose resolution is 640 × 1024 and sampling frequency is 1000 fps and 3000 fps, respectively. Meanwhile, four news lights are used as the ambient light source. Before the test, it is necessary to adjust the focus, pixels, frame rate and position of cameras to obtain clear and centered photos. The protective recovery system includes cushions, lifting devices, recovery fixtures, etc. The cushion can reduce the impact of the collision load on the projectile and protect its head.
In order to study the influence of head forms on the cavitation shape and projectile motion, the test models in
Figure 2 were designed with a diameter (D) of 20 mm and length-to-diameter ratio (L/D) of 6. The masses of the 60° cone, 90° cone and hemispherical head projectiles are 61.8 g, 63.1 g and 64.7 g, respectively. The models are hollow and segmented, which can reduce the mass and be convenient to replace the head section. Besides this, sealing rings are installed at the head and tail with the middle section to prevent water ingress.
From the experiment, the definition of parameters and motion coordinates are shown in
Figure 3. The water surface position and the time when the head touches the surface are specified as zero, and the value is negative underwater. The length and maximum thickness of bubbles are defined as as
lB and
rB, whose dimensionless forms are defined as
LB =
lB/D and
RB =
rB/D. The angle between the body axis and vertical direction is deflection angle
θ, and the clockwise is negative.
Cavitation number is a dimensionless parameter that characterizes the cavitation state. However, in this paper, the local cavitation number [
33] is introduced to describe the cavitation development at any time, whose definition is
where
is the ambient pressure,
is the saturated vapor pressure at the local temperature,
is the density of water,
v and
h are the speed and depth of the projectile at a certain time. When
v and
h are equal to the launch speed and depth at the corresponding time, the local cavitation number can be called the launch cavitation number.
3. Results and Discussion
In order to investigate the influence of the head forms and launch speeds on the evolution of bubble shape and the movement characteristics of the projectile, the experimental initial conditions involve three head forms of 60° cone, 90° cone and hemisphere as well as three launch speeds of 16.8 m/s, 18.5 m/s and 20.0 m/s, whose launch cavitation number is 0.714, 0.589 and 0.504, respectively.
3.1. The Effect of Head Forms on Cavitation Process
This section analyzes the cavitation characteristics based on the water-exit tests of three head-shaped projectiles with a launch speed of 18.5 m/s. The unsteady cavitation evolution experiences three stages of growth, shedding and collapse in the process of the projectile launching, cruising and exiting water, as shown in
Figure 4 and
Figure 5.
In the growth stage, the local pressure decreases at the shoulder of projectiles where the flow separation occurs, so that the water phase changes to form a transparent single bubble, into which the residual gas from the launcher escapes, and the length and thickness of cavities increase linearly with time to be stable.
In the shedding stage, the water flow moves back to the closure of bubbles, forming a reverse pressure gradient to generate a re-entry jet which advances along the projectile’s surface and makes the cavitation cloud shed and rupture from bottom to top. With the generation of new bubbles at the shoulder, the size of cavities changes: when the bubbles merge or rupture, the length increases or decreases correspondingly while the thickness changes randomly, and the tail cavities pull off this time.
In the collapse stage, the bubbles collapse from bottom to top under the influence of environmental pressure changes and three phases of water, gas and water vapor when the projectile exits the water, forming a large splash.
Comparing cavitation differences in the size and morphology changes among three head forms, it can be found that the bubble cloud of 60° cone head projectiles grows widely, which is easily interfered by the gas from the tube because of the large gap between the projectile and launcher. The cavitation size range of 90° cone head projectiles is narrow, and its bubble cloud is early to occur and easy to shed and rupture frequently, making it so that the projectile deflection is obvious. The cavitation evolution and movement of hemispherical head projectiles is relatively stable, which is not easy to be affected by the free water surface.
Since the re-entry jet affects the cavitation stability, its motion of three head forms in a period to study were selected, as shown in
Figure 6, where the red arrow indicates its movement position. It can be seen from the figure that the re-entry jet is a mixture of water and gas, for its color is similar to the edge of bubbles, moving upstream from the closure of the cavity along the projectile’s surface, so that the cavity shortens and sheds from bottom to top with its edge concave. The bubble of the 90° cone head is short, while the fast-moving re-entry jet causes the cavity to grow and shed frequently in a small area, which intensifies the deflection of projectiles. This indicates that the increase in the generation length of the cavity and the motion time of the re-entry jet within one cycle can reduce the occurrence of the cavitation shedding in the whole process and alleviate the instability of the cavitation evolution and the projectile movement.
From the definition and curve change of the local cavitation number, it can be seen that with the velocity and depth decreasing after launch, the value slowly increases as a quadratic curve form, which indicates that the cavitation number is mainly affected by speed. To explore the relationship between cavitation and
, the analysis of
Figure 7 combined with the cavitation evolution found that the bubbles of the 90° cone head with a large
grow and shed randomly in a small range, which indicates that the cloud cavitation is easy to occur when
is small in the growth stage, while the cavitation stability is worse when
is larger in the shedding stage.
3.2. The Effect of Launch Speeds on Cavitation Process
Figure 8,
Figure 9 and
Figure 10 show the cavitation shape and size evolution of various head forms at two launch speeds of 16.8 m/s and 20.0 m/s. A comparative analysis found that the effect of speeds on cavitation characteristics for different head forms has some common rules: Launch speed mainly affects the stable size of the cavity growth and the frequency of the cavity shedding. At low speed, the cavity bubbles will shed and rupture more randomly and frequently, while the bubbles will grow longer and thicker when the launch speed increases, which obviously improves the cavitation stability.
The hemispherical and 60° cone head projectiles move obliquely at low speeds due to the impact of the cavity collapse and air mass from the launcher. The cavity bubbles of hemispherical heads are small and few at low speeds, while the cloud cavitation is obvious at high speed, which indicates that the cavitation is not easy to occur in the hemispherical head projectile. In addition, before the significant cloud cavitation occurs, the increase in speeds will change the shape of cavity bubbles, which will transform the cavitation cluster from a point-like distribution to a cloud-like distribution.
The 90° cone and hemispherical heads with large differences in cavitation are selected for the dimensionless parameter analysis at three launch speeds. As seen from
Figure 11, the local cavitation number of two head forms is small at high speed, whose cavitation development is relatively stable in
Figure 8, which indicates that increasing the launch speed can reduce the cavitation number and improve the cavitation stability. Comparing the cavitation and dimensionless parameters of two heads, it is found that the cloud cavitation of hemispherical heads is obvious when the local cavitation number is low, which indicates that the hemispherical head is not prone to cavitation, whose critical cavitation number is small. When the 90° cone head projectile moves slowly in a deceleration process, the size fluctuation of shedding bubbles is strong; meanwhile the curve rises sharply, which indicates that the local cavitation number increases rapidly as the speed decreases, causing cavitation unstable.
3.3. Research on the Projectile Movement
The projectile is launched out by the high-pressure gas in a roughly uniformly accelerated motion. Due to the multiple effects of the residual gas, fluid drag and unstable cavitation, its movement trajectory will shift gradually and its velocity will reduce slowly. When the projectile exits the water, its speed drops sharply and the motion trajectory deflects greatly by the unbalanced force of the water surface disturbance and cavitation collapse. To study the effects of head forms and launch speeds on the motion characteristics of projectiles, the speed, trajectory and deflection angle change curves are shown respectively in
Figure 12,
Figure 13,
Figure 14 and
Figure 15.
Due to the difference in model quality and cavitation characteristics, the launch speeds of three head-shaped projectiles under the same pressure are not alike, as shown in
Figure 12a. The launch speed of 60° cone head projectiles is the largest because of its lightest mass; the hemispherical head projectile is heavy, but its cavitation is connected to the air mass near the launch tube, which is similar to the ventilated cavitation with a drag reduction effect; the launch speed of 90° cone head projectiles is the smallest under the effects of the repeated growth, shedding and fracture of the cavitation. Therefore, the mean velocity of three variable-speed launch tests is 16.8 m/s, 18.5 m/s, 20.0 m/s.
Figure 12b shows the variation curve of the deflection angle for three head forms when the average launch speed is about 18.5 m/s. Comparing the motion trajectories and deflection angles of three head-shaped projectiles at this speed, it is found that the hemispherical head projectile deflects less than 1°, so its motion characteristic is relatively stable. When the 60° cone head projectile exits the water, its bubbles on two sides are not symmetrical and the collapse impact is strong, causing an unbalanced force on the projectile with a deflection of about 2.5°. The deflection of 90° cone head projectiles is seriously affected by the attached cavitation shedding and collapse, so its motion stability is poor.
Figure 14 and
Figure 15 show the variation curve of motion parameters for conical head projectiles. It can be found that the variation range of movement speeds and deflection angles of the 60° cone head is smaller than that of the 90° cone head, which indicates that the motion of 60° cone head projectiles is relatively stable. As shown in
Figure 14, because drag is positively related to speed, the projectile at high speed is interfered significantly by the fluid, so that its velocity reduces rapidly. As seen from
Figure 13 and
Figure 15, three head-shaped projectiles deflect severely at low and medium speeds, while the deflection angle reduces as the speed increases, indicating that the increasing launch speed can improve motion stability.
4. Conclusions
Based on a self-designed underwater launch platform, this paper carried out vertical water-exit tests of scaled models with different head forms and launch speeds. Through the further analysis of the unsteady cavitation and projectile movement, the conclusions were obtained as follows:
(1) Cavitation evolution experiences three stages: stable growth, shedding with rupture, and collapse. A phase change occurs at the low-pressure area of the projectile’s shoulder, forming cavitation. Affected by the re-entry jet, the cavity falls off from its tail to head. The cavity collapses quickly from its top to bottom out of the water with a strong impact jet, which causes the projectile to deflect.
(2) The research on the relationship between the re-entry jet and cavitation number with cavitation stability indicates that: the periodic development of the re-entry jet and cavitation affects the shedding frequency together; the cavitation can be predicted by the cavitation number—when its value is small, the phase change occurs easily with large cavity growth size and low shedding frequency.
(3) Comparing the cavitation and movement of different head forms and launch speeds, it is found that the hemispherical head is anti-cavitation. The cavitation development of the 90° cone head shows a small area of the high-frequency growth and shedding. The cavitation evolution of the 60° cone head is easily affected by the gas near the tube. The launch speed affects the growth size and shedding frequency of bubbles mainly, so it can improve the stability of the cavitation evolution and projectile’s movement by increasing the launch speed.