Comparison of Fiber-to-Waveguide Couplers in Point Diffraction Interferometer Based on Waveguide Reference Wavefront Source

Abstract

To improve the power of reference wavefront generated by reference wavefront source (RWS) based on silicon nitride (SiN) waveguide in point diffraction interferometer (PDI), we design the Y-branch coupler and grating coupler, and then compare the maximum coupling efficiency, 3 dB fabrication tolerance, 3 dB alignment tolerance and polarization dependent loss of two couplers. Our results show that grating coupler has higher coupling efficiency, lower etching difficulty and alignment difficulty, while Y-branch coupler has lower coating difficulty. To get the maximum efficiency, mode in the fiber must be TE mode no matter for grating coupler or Y-branch coupler. This paper improves the power of the wavefront by selecting appropriate fiber-to-waveguide couplers for waveguide RWS. PDI based on the power improved waveguide RWS is expected to be used in many measurement fields.

1. Introduction

Reference wavefront used in traditional interferometers [1] such as Twyman–Green interferometer and Fizeau interferometer is generated by reflection of a standard reference mirror, so accuracy of the reference wavefront is limited by fabrication accuracy of the standard reference mirror which is usually not better than $\lambda /40$ ($\lambda =532 \mathrm{nm}$). Different from above interferometers, reference wavefront used in the point diffraction interferometer (PDI) [2,3,4,5,6,7] is generated by a diffraction element called reference wavefront source (RWS). RWS generates a nearly ideal spherical reference wavefront by diffraction at a small aperture of micrometer diameter, so accuracy of the reference wavefront is not limited by a standard reference mirror and can reach sub-nanometer scale. To improve the accuracy, numerical aperture (NA), and power of the reference wavefront, and further expand the application of PDIs, researchers have proposed and made various RWSs.

Pinhole RWS and fiber RWS are two commonly used RWSs. Pinhole RWS [8,9,10,11] is made by etching a submicron pinhole on the metal film. Such a small pinhole can generate a high accuracy spherical reference wavefront and its NA is up to 0.3, but low light transmittance of this small pinhole ($<0.1\%$) seriously reduces the power of the reference wavefront [12]. Pinhole RWS can also be fabricated by other materials like liquid crystal [13] or metal wire grid [14], but these pinhole RWSs also have the above problems.

Fiber RWS [12,15,16,17] generates the reference wavefront by diffraction at the end face of the single-mode fiber (SMF). Due to high light transmittance of the SMF, power of the generated reference wavefront is high [12]. But due to limitation of the SMF core diameter (3–5 µm) [17], NA of this reference wavefront is usually less than 0.2, which greatly limits the NA of the optical element to be tested. Using a special SMF with a submicron end face is an effective way to improve the NA of the reference wavefront, but this kind of SMF is difficult to fabricate and clamp.

To make the reference wavefront have high accuracy, NA, and power simultaneously, our group has designed a new RWS based on the silicon nitride (SiN) waveguide. Due to high refractive index difference between the SiN core ($n=1.96,\lambda =532 \mathrm{nm}$) and silicon dioxide (SiO₂) cladding ($n=1.48,\lambda =532 \mathrm{nm}$), light in the waveguide is firmly confined in the core whose cross-section side length is 0.25 µm, and propagates along the core to the output facet. Then, light is diffracted at the output facet, and spherical reference wavefront is generated. NA of this reference wavefront is more than 0.5, and root-mean-square (RMS) value is less than 0.03 nm. Power of this reference wavefront is mainly determined by coupling efficiency between the SMF and waveguide RWS. To get the maximum coupling efficiency, two fiber-to-waveguide couplers called Y-branch coupler [18,19,20] and grating coupler [21,22,23] are designed by numerical simulation. Then, coupling efficiency, 3 dB alignment tolerance, 3 dB fabrication tolerance, and polarization-dependent loss of two couplers are compared.

Rest of this paper is organized as follows. In Section 2, structure of the waveguide RWS and its operation are first introduced. Then, accuracy, NA and power of the reference wavefront are analyzed. In Section 3 and Section 4, Y-branch coupler and grating coupler are introduced in detail, including structure of the coupler, key parameters affecting the coupling efficiency, fabrication difficulty, alignment difficulty, and polarization-dependent loss. Y-branch coupler and grating coupler are compared in Section 5. In Section 6, a summary of this paper is made.

In this paper, numerical simulation is performed based on the finite difference time domain (FDTD) method. In the simulation, wavelength is 532 nm, refractive index of SiN is 1.96, refractive index of SiO₂ is 1.48, diameter of the SMF core is 3 µm, refractive index of the SMF core is 1.4620, and refractive index of the SMF cladding is 1.4571. TE mode refers to the mode whose main component is along the $x$ direction in the $x-y$ plane when electric field propagates along the $z$ direction, and TM mode refers to the mode whose main component is along the $y$ direction. For convenience, these will not be repeated in the rest of the paper.

2. Reference Wavefront Source Based on SiN Waveguide

In this section, structure of the waveguide reference wavefront source (RWS) and its principle to generate the reference wavefront are introduced firstly. Then, important parameters of the waveguide RWS that influence the accuracy, numerical aperture (NA), and power of the reference wavefront are mentioned.

As shown in Figure 1, structure of the waveguide RWS is similar to the buried waveguide: silicon nitride (SiN) core with a thickness of 250 nm in the $y$ direction is buried between the silicon dioxide (SiO₂) bottom cladding of 2.52 µm thickness and SiO₂ top cladding of 2 µm thickness. SiO₂ bottom cladding is located on the silicon (Si) substrate of 3 mm thickness. This waveguide RWS can be divided into four parts and each part has its function. Part A₁ (Y-branch Coupler) or Part A₂ (grating coupler) is used to improve the coupling efficiency between the single-mode fiber (SMF) and waveguide, and further increase the power of the reference wavefront. Therefore, fiber-to-waveguide coupler is the most important part in the design of the waveguide RWS. Part B and Part C are the straight waveguide. Part C is a bent waveguide with the sector angle of $90°$. This bent waveguide makes the reference wavefront perpendicular to the incident light, which avoids the interference between them.

Waveguide RWS generates the spherical reference wavefront by diffraction at the output facet of the SiN core. This process is as follows: 532 nm incident light provided by the laser propagates to the fiber-to-waveguide coupler along the SMF. This incident light can be coupled into the waveguide either by the Y-branch coupler (Part A₁) or the grating coupler (Part A₂) and then propagates along the core. Due to high refractive index difference between the SiN core and SiO₂ cladding, light in the waveguide is strongly confined in the sub-micron core during the propagation. Finally, light arrives at the output facet and spherical reference wavefront is generated by diffraction.

Accuracy and numerical aperture (NA) of the reference wavefront are determined by the size of the core cross-section ($y-z$ cross-section of the core in Figure 1). SiN core of the waveguide RWS has a square cross-section of 0.25 µm in length, which satisfies the single-mode propagation condition. Accuracy and NA of the reference wavefront generated by this waveguide RWS are calculated by numerical simulation and results are shown in Figure 2. When NA of the reference wavefront is 0.3, peak-to-valley (PV) value and root-mean-square (RMS) value are $1.07\times {10}^{-4}\lambda$ and $1.72\times {10}^{-5}\lambda$ ($\lambda =532 \mathrm{nm}$), respectively. When NA increases to 0.5, PV value and RMS value are $2.86\times {10}^{-4}\lambda$ and $4.83\times {10}^{-5}\lambda$, respectively. Even if NA of the reference wavefront reaches 0.5, RMS value is still less than 0.03 nm. Such a high accuracy reference wavefront cannot be generated by a pinhole RWS or fiber RWS.

Power of the reference wavefront is determined by the coupling efficiency between the SMF and waveguide. Therefore, an optimal fiber-to-waveguide coupler must be designed to improve the coupling efficiency. To provide a reliable reference for the selection of a fiber-to-waveguide coupler, Y-branch coupler and grating coupler are compared in detail, including their max coupling efficiency, 3 dB fabrication tolerance, 3 dB alignment tolerance and polarization-dependent loss.

3. Y-Branch Coupler

Using the Y-branch coupler is an effective way to improve the coupling efficiency between the single-mode fiber (SMF) and waveguide. In this section, firstly, structure of the Y-branch coupler is introduced and its key parameters are optimized to get the maximum coupling efficiency. Secondly, to quantitatively evaluate the fabrication difficulty and alignment difficulty of the coupler, 3 dB fabrication tolerance, 3 dB alignment tolerance, and polarization-dependent loss are analyzed, respectively.

3.1. Structure of the Y-Branch Coupler

Figure 3 shows the structure of the Y-branch coupler, including the input part and branch part. There are two identical and parallel straight structures in the input part. Width of each straight structure is $W$ and gap between two straight structures is $G$. In the branch part, two straight structures merge into one and length of this part is $L_{\mathrm{b}}$. Height of the Y-branch coupler along the $y$ direction is 250 nm, which is consistent with the height of the silicon nitride (SiN) core.

To get the maximum coupling efficiency, the SMF should be aligned to the Y-branch coupler center and the two should be as close as possible. Coupling efficiency of the Y-branch coupler ${\eta }_{\mathrm{y}}$ can be calculated as follow:

$${\eta }_{\mathrm{y}}={\eta }_{\mathrm{y}1}\cdot {\eta }_{\mathrm{y}2}$$

(1)

where ${\eta }_{\mathrm{y}1}$ denotes the matching degree between the mode in the SMF and mode in the input part, ${\eta }_{\mathrm{y}2}$ denotes the transmission efficiency of the branch part.

3.2. Parameter Optimization

Matching degree between the mode in the SMF and mode in the input part (${\eta }_{\mathrm{y}1}$) can be calculated using the follow overlap integral:

$${\eta }_{\mathrm{y}1}=\frac{{\left|{\displaystyle \iint E_{\mathrm{f}}}\left(x,y\right)E_{\mathrm{w}}^{\ast }\left(x,y\right)dxdy\right|}^2}{{\displaystyle \iint {\left|E_{\mathrm{f}}\left(x,y\right)\right|}^{2}dxdy{\displaystyle \iint {\left|E_{\mathrm{w}}\left(x,y\right)\right|}^{2}dxdy}}}$$

(2)

where $E_{\mathrm{f}}\left(x,y\right)$ denotes the mode in the SMF, $E_{\mathrm{w}}\left(x,y\right)$ denotes the mode in the input part, $\ast$ denotes the complex conjugate.

Influence of the width $W$ and gap $G$ on the mode matching degree ${\eta }_{\mathrm{y}1}$ is shown in Figure 4a,b. Firstly, compared with TM mode, mode matching degree ${\eta }_{\mathrm{y}1}$ is greater when TE mode is in the SMF, indicating that mode matching degree ${\eta }_{\mathrm{y}1}$ is polarization sensitive. Therefore, mode in the SMF must always be TE mode to ensure the maximum mode matching degree. Secondly, mode matching degree ${\eta }_{\mathrm{y}1}$ increases with the decrease of the width $W$, because area of the mode in the input part is inversely proportional to the width $W$. Thirdly, mode matching degree ${\eta }_{\mathrm{y}1}$ first increases and then decreases, when gap $G$ increases from small to large. Because area of the mode in the input part also increases first and then decreases, during the growth of the gap $G$. According to above results, width $W$ should be as small as possible to improve the mode matching degree ${\eta }_{\mathrm{y}1}$. However, limited by the current waveguide fabrication technology, minimum width $W$ is only 0.10 µm. Therefore, maximum mode matching degree ${\eta }_{\mathrm{y}1}$ can reach 0.24, when TE mode is in the SMF and width $W$ and gap $G$ are 0.10 µm and 0.86 µm, respectively.

Transmission efficiency of the branch part (${\eta }_{\mathrm{y}2}$) is closely related to length of the branch part ($L_{\mathrm{b}}$), and it can be calculated as follows:

$${\eta }_{\mathrm{y}2}=\frac{P_{\mathrm{o}}}{P_{\mathrm{i}}}$$

(3)

where $P_{\mathrm{i}}$ denotes the power on the right of the branch part as shown in Figure 3b, $P_{\mathrm{o}}$ denotes the power on the left of the branch part. Figure 4c shows the relationship between the transmission efficiency ${\eta }_{\mathrm{y}2}$ and length $L_{\mathrm{b}}$. When length $L_{\mathrm{b}}$ is small, transmission efficiency ${\eta }_{\mathrm{y}2}$ increases sharply as the length $L_{\mathrm{b}}$ increases. With the further increase of the length $L_{\mathrm{b}}$, increase tendency of the transmission efficiency slows down. After length $L_{\mathrm{b}}$ is greater than 10 µm, transmission efficiency ${\eta }_{\mathrm{y}2}$ is nearly equal to 1, no matter for TE mode or TM mode in the SMF.

In summary, when TE mode is in the SMF, and width $W$, gap $G$, and length $L_{\mathrm{b}}$ are 0.10 µm, 0.86 µm, and 10 µm respectively, maximum mode matching degree ${\eta }_{\mathrm{y}1}$ can reach 0.24, and transmission efficiency ${\eta }_{\mathrm{y}2}$ is approximately equal to 1. Therefore, the maximum coupling efficiency of the Y-branch coupler (${\eta }_{\mathrm{y}}$) is 0.24.

3.3. 3 dB Fabrication Tolerance of the Y-Branch Coupler

Fabrication errors make the fabricated coupler different from the designed one, leading to reduction of the coupling efficiency, especially for the parameters of the submicrometer scale. 3 dB fabrication tolerance refers to variation range of the parameter when coupling efficiency drops to half of the maximum. In this section, 3 dB fabrication tolerance of the width $W$, and gap $G$ are analyzed.

Firstly, 3 dB fabrication tolerance of the gap $G$ is analyzed and width $W$ is 0.10 µm during the analysis. As shown in Figure 5a, mode matching degree ${\eta }_{\mathrm{y}1}$ reaches its maximum value of 0.24 when gap $G$ is 0.86 µm. Once gap $G$ decreases to 0.16 µm or increases to 2.26 µm, mode matching degree ${\eta }_{\mathrm{y}1}$ drops to half of the maximum. Therefore, 3 dB fabrication tolerance of the gap $G$ is −0.70 µm–+1.40 µm.

Secondly, 3 dB fabrication tolerance of the width $W$ is analyzed and gap $G$ is 0.86 µm. The relationship between the mode matching degree ${\eta }_{\mathrm{y}1}$ and width $W$ is shown in Figure 5b. When width $W$ is smaller than 0.10 µm, mode matching degree ${\eta }_{\mathrm{y}1}$ is higher than 0.24. When width $W$ increases from 0.10 µm to 0.15 µm, mode matching degree ${\eta }_{\mathrm{y}1}$ drops from 0.24 to 0.12. Therefore, 3 dB fabrication tolerance of the width $W$ is −0.10 μm–+0.05 μm.

3.4. 3 dB Alignment Tolerance of the Y-Branch Coupler

Figure 6a shows the alignment of the SMF and Y-branch coupler. To achieve maximum coupling efficiency, it is necessary to carefully adjust the SMF along the $x$, $y$, and $z$ directions, so that SMF center and coupler center can be on the same line and overlapped. In this section, 3 dB alignment tolerance of the Y-branch coupler is analyzed to quantitatively evaluate the difficulty of the alignment.

Adjustments in the $z$ direction are completed if there is no gap between the SMF and Y-branch coupler. These adjustments are relatively simple, so alignment tolerance in the $z$ direction is not analyzed in this paper. Influence of the deviation between the SMF center and coupler center in the $x-y$ plane on the coupling efficiency ${\eta }_{\mathrm{y}}$ is shown in Figure 6b. In this figure, $dx$ denotes the deviation between the SMF center and coupler center in the $x$ direction, $dy$ denotes the deviation in the $y$ direction, color bar denotes the normalized coupling efficiency. It is clear to know that the greater the deviation between the SMF center and coupler center is, the lower the coupling efficiency will be. When deviation is outside the red circle, coupling efficiency drops to half of the maximum. Therefore, 3 dB alignment tolerance of the Y-branch coupler is $\sqrt{d{x}^2+d{y}^2}\le 1.10 \mathsf{\mu }\mathrm{m}$.

3.5. Polarization Dependent Loss of the Y-Branch Coupler

Polarization of mode keeps unchanged if SMF is completely axisymmetric. However, if SMF bends, polarization of mode changes immediately and then coupling efficiency of fiber-to-waveguide coupler changes too [24]. Polarization-dependent loss refers to the decrease in coupling efficiency when mode in the SMF changes from TE mode to TM mode, and it is used to quantitatively evaluate the influence of mode polarization on the coupling efficiency. Polarization-dependent loss ${\eta }_{\mathrm{p}}$ can be calculated as follow:

$${\eta }_{\mathrm{p}}=\left|{\eta }_{\mathrm{y}}\left(\mathrm{TE}\right)-{\eta }_{\mathrm{y}}\left(\mathrm{TM}\right)\right|$$

(4)

where ${\eta }_{\mathrm{y}}\left(\mathrm{TE}\right)$ denotes the coupling efficiency between the SMF and Y-branch coupler when TE mode is in the SMF, ${\eta }_{\mathrm{y}}\left(\mathrm{TM}\right)$ denotes the coupling efficiency when TM mode is in the SMF. Coupling efficiency ${\eta }_{\mathrm{y}}\left(\mathrm{TE}\right)$ and ${\eta }_{\mathrm{y}}\left(\mathrm{TM}\right)$ are 0.24 and 0.13 respectively when width $W$ is 0.10 µm, gap $G$ is 0.86 µm, and length $L_{\mathrm{b}}$ is 10 µm. Therefore, polarization-dependent loss of the Y-branch coupler (${\eta }_{\mathrm{p}}$) is 0.11.

4. Grating Coupler

Using the grating coupler is also an effective way to improve the coupling efficiency between the single-mode fiber (SMF) and waveguide reference wavefront source (RWS). Different from Y-branch coupler, grating coupler can be placed at any position of the waveguide RWS and edge of the waveguide RWS does not need to be polished. In this section, firstly, structure of the grating coupler is introduced and key parameters that determine the coupling efficiency are optimized. Secondly, 3 dB fabrication tolerance, 3 dB alignment tolerance, and polarization-dependent loss are analyzed, respectively.

4.1. Structure of the Grating Coupler

Figure 7 shows the structure of the grating coupler which is composed of the grating part and taper part. In the grating part, width of the non-etched area is $p$, width of the etched area is $q$, grating period $\mathsf{\Lambda }=p+q$, duty cycle $d=p/\mathsf{\Lambda }$, and width of the grating part is $b$. In the taper part, $L_{\mathrm{t}}$ denotes its length. Height of the grating coupler along the $y$ direction is 250 nm, which is consistent with the height of the silicon nitride (SiN) core.

Coupling efficiency of the grating coupler (${\eta }_{\mathrm{g}}$) can be calculated as follow:

$${\eta }_{\mathrm{g}}={\eta }_{\mathrm{g}1}\cdot {\eta }_{\mathrm{g}2}$$

(5)

where ${\eta }_{\mathrm{g}1}$ denotes the coupling efficiency between the SMF and grating part, ${\eta }_{\mathrm{g}2}$ denotes the transmission efficiency of the taper part. To improve the coupling efficiency of the grating coupler, parameters in the grating part and taper part must be optimized.

4.2. Parameter Optimization

Parameter optimization of the grating coupler can be divided into two steps. In the first step, parameters in the grating part are optimized. Bragg diffraction equation [25] is firstly used to calculate the initial value of each parameter. Then, each parameter is continuously adjusted from its initial value by using the particle swarm optimization method [26], so that coupling efficiency ${\eta }_{\mathrm{g}1}$ tends to the maximum. In the second step, width $b$ and length $L_{\mathrm{t}}$ are optimized to improve the transmission efficiency ${\eta }_{\mathrm{g}2}$.

Simulation mode of the grating part is shown in Figure 8a. Since width of the grating part along the $x$ direction does not affect the coupling efficiency, two-dimensional finite difference time domain (FDTD) simulation is used which also can greatly save the simulation time and computer memory. In Figure 8a, incident angle $\theta$ denotes the angle between the SMF and normal line, $z$ denotes the horizontal distance from the left of the grating to the SMF center, $y$ denotes the vertical distance from the top of the grating to the SMF center, arrows denote propagation directions of the lights, PML denotes the perfectly matched layer boundary condition.

Bragg diffraction equation is given by:

$$n_{\mathrm{e}}+m\frac{\lambda }{\mathsf{\Lambda }}=n_1\sin \theta$$

(6)

where $n_{\mathrm{e}}$ denotes the refractive index of the grating, $\lambda$ denotes the wavelength of the light, $\mathsf{\Lambda }$ denotes the grating period, $m$ denotes the diffraction order, $n_1$ denotes the refractive index of the air, $\theta$ denotes the incident angle of the SMF. Initial value of the incident angle $\theta$ is chosen to be $20°$ to avoid the second-order reflection at the grating. Since initial values of the duty cycle $d$ and wavelength $\lambda$ are 0.5 and 0.532 µm, respectively, refractive index of the grating $n_{\mathrm{e}}$ can be calculated, and its value is 1.60. According to Equation (6), initial value of the grating period $\mathsf{\Lambda }$ is 0.423 µm when diffraction order is −1. Initial value of each parameter is shown in

Table 1. Parameters of the grating part.

Parameters	$\mathbf{\Lambda }$ (µm)	$\mathit{d}$	$\mathit{p}$ (µm)	$\mathit{q}$ (µm)	$\mathit{\theta }$ (°)	$\mathit{z}$ (µm)	$\mathit{y}$ (µm)
Original	0.423	0.500	0.211	0.212	20	0	0
Final	0.420	0.476	0.200	0.220	20	3.4	3.2

.

To get the maximum coupling efficiency, four parameters including the grating period $\mathsf{\Lambda }$, duty cycle $d$, $z$, and $y$ are optimized together using the particle swarm optimization method [26]. After 300 iterations, coupling efficiency ${\eta }_{\mathrm{g}1}$ reaches its maximum of 0.35. The final value of each parameter can also be seen in Table 1. It is worth mentioning that coupling efficiency ${\eta }_{\mathrm{g}1}$ is polarization sensitive and it gets the maximum when TE mode is in the SMF. Therefore, numerical simulations in the rest of this section use the TE mode.

Transmission efficiency ${\eta }_{\mathrm{g}2}$ which is determined by the width $b$ and length $L_{\mathrm{t}}$ can be calculated as follow:

$${\eta }_{\mathrm{g}2}=\frac{{P_{\mathrm{o}}}^{\prime }}{{P_{\mathrm{i}}}^{\prime }}$$

(7)

where ${P_{\mathrm{i}}}^{\prime }$ denotes the power on the right of the taper part as shown in Figure 7b, ${P_{\mathrm{o}}}^{\prime }$ denotes the power on the left. Figure 8b shows the transmission efficiency ${\eta }_{\mathrm{g}2}$ with different width $b$ and length $L_{\mathrm{t}}$. Firstly, with the increase of the length $L_{\mathrm{t}}$, transmission efficiency ${\eta }_{\mathrm{g}2}$ continues to improve and tends to be 1. Secondly, when width $b$ increases, length $L_{\mathrm{t}}$ should increase at the same time to keep the transmission efficiency ${\eta }_{\mathrm{g}2}$ constant. Considering the fact that diameter of the mode in the SMF is 3 µm, grating part whose width $b$ is 6 µm, is big enough to accept the whole light spot from the SMF because diameter of the mode in the SMF is 3 µm. Once width $b$ is chosen to be 6 µm, transmission efficiency of the taper part is nearly close to 1 when length $L_{\mathrm{t}}$ is 300 µm.

In summary, when parameters of the grating part are final values in Table 1, and width $b$ and length $L_{\mathrm{t}}$ are 6 µm and 300 µm respectively, coupling efficiency ${\eta }_{\mathrm{g}1}$ reaches its maximum 0.35, and transmission efficiency ${\eta }_{\mathrm{g}2}$ is approximately equal to 1. Therefore, maximum coupling efficiency of the grating coupler (${\eta }_{\mathrm{g}}$) is 0.35.

4.3. 3 dB Fabrication Tolerance of the Grating Coupler

To quantitatively evaluate the difficulty of fabricating the grating coupler and to compare it with the difficulty of fabricating the Y-branch coupler, 3 dB fabrication tolerance of the grating period $\mathsf{\Lambda }$, duty cycle $d$ and thickness of the bottom cladding $h$ are analyzed.

Effect of the grating period $\mathsf{\Lambda }$ on the coupling efficiency ${\eta }_{\mathrm{g}1}$ is shown in Figure 9a. Grating period $\mathsf{\Lambda }$ and incident angle $\theta$ must satisfy the Bragg diffraction equation (Equation (6)) to get the maximum coupling efficiency ${\eta }_{\mathrm{g}1}$. However, the incident angle $\theta$ remains unchanged in the experiment. This leads to a decrease of the coupling efficiency ${\eta }_{\mathrm{g}1}$ regardless of the decrease or increase of the grating period $\mathsf{\Lambda }$. When grating period $\mathsf{\Lambda }$ decreases to 0.40 µm or increases to 0.44 µm, coupling efficiency ${\eta }_{\mathrm{g}1}$ drops to half of the maximum. Therefore, 3 dB fabrication tolerance of the grating period $\mathsf{\Lambda }$ is −0.02 μm–+0.02 μm.

Figure 9b shows the effect of duty cycle $d$ on the coupling efficiency ${\eta }_{\mathrm{g}1}$ when grating period $\mathsf{\Lambda }$ is 0.420 μm. Coupling efficiency ${\eta }_{\mathrm{g}1}$ increases first and then decreases with the increase of the duty cycle $d$. Because too large or too small duty cycle $d$ enhances the transmission characteristics of the grating and finally leads to the reduction of the coupling efficiency. When duty cycle $d$ decreases to 0.36 or increases to 0.60, coupling efficiency ${\eta }_{\mathrm{g}1}$ drops to half of the maximum. Therefore, 3 dB fabrication tolerance of the duty cycle $d$ is −0.12 μm–+0.12 μm. In other words, 3 dB fabrication tolerance of the width $p$ or $q$ is −0.05 μm–+0.05 μm.

Thickness of the bottom cladding $h$ also affects the coupling efficiency ${\eta }_{\mathrm{g}1}$. Arrows in Figure 8a clearly show the propagation of the incident light after it enters the grating coupler from the SMF. The light reflected by the substrate (D_reflect) interferes with the light propagating to the waveguide (D_left), leading to the result that coupling efficiency ${\eta }_{\mathrm{g}1}$ changes periodically with the increase of the thickness $h$. Figure 9c shows this phenomenon clearly. Coupling efficiency ${\eta }_{\mathrm{g}1}$ reaches its maximum of 0.35 when thickness $h$ is 2.52 μm. Coupling efficiency ${\eta }_{\mathrm{g}1}$ drops to half of the maximum once thickness $h$ decreases to 2.46 μm or increases to 2.58 μm. Therefore, 3 dB fabrication tolerance of the thickness $h$ is −0.06 μm–+0.06 μm.

4.4. 3 dB Alignment Tolerance of the Grating Coupler

When aligning the SMF and grating coupler in the experiment, incident angle $\theta$ remains unchanged and position of the SMF is continuously adjusted to get the maximum coupling efficiency. Therefore, only 3 dB alignment tolerance of the $z$ and $y$ is analyzed.

When SMF deviates from the ideal position, effect of the SMF position on the coupling efficiency ${\eta }_{\mathrm{g}1}$ is shown in Figure 10a. Firstly, with the growth of the $z$, coupling efficiency ${\eta }_{\mathrm{g}1}$ increases to its maximum and then drops. Secondly, with the growth of the $y$, maximum of the coupling efficiency ${\eta }_{\mathrm{g}1}$ changes in the same way. When $y$ is 3.2 μm, coupling efficiency ${\eta }_{\mathrm{g}1}$ gets its maximum of 0.35 at z = 3.4 μm and drops to half at z = 1.6 μm or 6.8 μm. Therefore, 3 dB alignment tolerance of the $z$ is −1.8 μm–+3.4 μm.

Figure 10b shows the influence of the $y$ on the maximum of the coupling efficiency ${\eta }_{\mathrm{g}1}$ detailly. Coupling efficiency ${\eta }_{\mathrm{g}1}$ gets its maximum of 0.35 at y = 3.2 μm and drops to half at y = 20.2 μm. Limited by the thickness of the top cladding, the minimum of the $y$ is 2 μm. Therefore, 3 dB alignment tolerance of the $y$ is −1.2 μm–+12.0 μm.

4.5. Polarization-Dependent Loss of the Grating Coupler

Polarization-dependent loss of the grating coupler (${{\eta }_{\mathrm{p}}}^{\prime }$) can be calculated as follow:

$${{\eta }_{\mathrm{p}}}^{\prime }=\left|{{\eta }_{\mathrm{TE}}}^{\prime }-{{\eta }_{\mathrm{TM}}}^{\prime }\right|$$

(8)

where ${{\eta }_{\mathrm{TE}}}^{\prime }$ denotes the coupling efficiency between the SMF and grating coupler when TE mode is in the SMF, ${{\eta }_{\mathrm{TM}}}^{\prime }$ denotes the coupling efficiency when TM mode is in the SMF. Coupling efficiency ${{\eta }_{\mathrm{TE}}}^{\prime }$ and ${{\eta }_{\mathrm{TM}}}^{\prime }$ are 0.35 and 0.05 respectively when parameters in the grating part are final values in Table 1, width $b$ is 6 μm, and length $L_{\mathrm{t}}$ is 300 μm. Therefore, polarization-dependent loss of the grating coupler (${{\eta }_{\mathrm{p}}}^{\prime }$) is up to 0.30.

5. Comparison of Two Fiber-to-Waveguide Couplers

Table 2. Characteristics of the Y-branch coupler.

$\mathit{W}$ (µm)	$\mathit{G}$ (µm)	$\mathit{d}\mathit{x}$ (µm)	$\mathit{d}\mathit{y}$ (µm)	${\mathit{L}}_{\mathbf{b}}$ (µm)	${\mathit{\eta }}_{\mathbf{y}}$	${\mathit{\eta }}_{\mathbf{p}}$
0.10 −0.10–+0.05	0.86 −0.70–+1.40	$\sqrt{d{x}^2+d{y}^2}\le 1.10$		10	0.24	0.11

and

Table 3. Characteristics of the grating coupler.

$\mathbf{\Lambda }$ (µm)	$\mathit{d}$	$\mathit{q}$ (µm)	$\mathit{p}$ (µm)	$\mathit{b}$ (µm)	$\mathit{\theta }$ (°)
0.40 −0.02–+0.02	0.476 −0.12–+0.12	0.22 −0.05–+0.05	0.20 −0.05–+0.05	6	20
$z$ (µm)	$y$ (µm)	$h$ (µm)	$L_{\mathrm{t}}$ (µm)	${\eta }_{\mathrm{g}}$	${{\eta }_{\mathrm{p}}}^{\prime }$
3.4 −1.8–+3.4	3.2 −1.2–+12.0	2.52 −0.06–+0.06	300	0.35	0.30

show the parameters, maximum coupling efficiency, 3 dB fabrication tolerance, 3 dB alignment tolerance, and polarization-dependent loss of the Y-branch coupler and grating coupler respectively. Following results can be obtained from two tables, firstly, maximum coupling efficiency of the grating coupler (${\eta }_{\mathrm{g}}=0.35$) is greater than Y-branch coupler (${\eta }_{\mathrm{y}}=0.24$). Secondly, in terms of the etching process, difficulty of fabricating the grating coupler is slightly less than that of the Y-branch coupler. When fabricating the Y-branch coupler, minimum size to be etched is 0.10 μm (width $W$) and its fabrication tolerance is −0.10 μm–+0.05 μm. Minimum size of the grating coupler is 0.20 μm (width $p$) and its fabrication tolerance is ±0.05 μm. Thirdly, in terms of the coating process, fabricating the Y-branch coupler is easier because thickness of the bottom cladding $h$ should be strictly controlled at 2.52 μm and its fabrication tolerance is ±0.06 μm. Fourthly, compared with the Y-branch coupler, it is easier to align the single-mode fiber (SMF) and grating coupler. Because Y-branch coupler must be located at the edge of the waveguide reference wavefront source (RWS), and edge of the waveguide RWS should be polished before using the Y-branch coupler. However, grating coupler does not have this problem. When aligning the SMF and Y-branch coupler, SMF center must be located in a circular area with the radius of 1.10 μm, and center of this circle is Y-branch coupler center. Aligning the SMF with the grating coupler is relatively simpler because of the greater alignment tolerance (−1.8 μm–+3.4 μm along the $z$ direction, −1.2 μm–+12.0 μm along the $y$ direction). Fifthly, polarization of the mode in the SMF has a great impact on the coupling efficiency no matter for the grating coupler or Y-branch coupler. When mode in the SMF changes from TE mode to TM mode, coupling efficiency of the grating coupler is even reduced by 0.3. Therefore, polarization of the mode in the SMF must be strictly controlled.

6. Conclusions

In this paper, reference wavefront source (RWS) based on silicon nitride (SiN) waveguide in point diffraction interferometer (PDI) is firstly introduced. Then, maximum coupling efficiency, 3 dB fabrication tolerance, 3 dB alignment tolerance and polarization-dependence loss of the Y-branch coupler and grating coupler are compared to improve the power of wavefront. Simulation results show that waveguide RWS can generate a reference wavefront whose root-mean-square (RMS) value is less than 0.03 nm and numerical aperture (NA) is over 0.5, owing to high refractive index difference between SiN core and silicon dioxide (SiO₂) cladding. Using Y-branch coupler or grating coupler is an effective way to improve the power of wavefront. Compared with Y-branch coupler, grating coupler is the more recommended fiber-to-waveguide coupler because its maximum coupling efficiency (${\eta }_{\mathrm{g}}=0.35$) is greater. Moreover, etching process and alignment process of grating coupler are easier. Y-branch coupler is a better choice if the coating technology cannot meet the requirement (fabrication tolerance is ±0.06 μm). Finally, polarization of the mode in the single-mode fiber (SMF) must be strictly controlled no matter for grating coupler or Y-branch coupler. This paper improves the power of the wavefront by selecting appropriate fiber-to-waveguide couplers for waveguide RWS. PDI based on the power improved waveguide RWS is expected to be used in many measurement fields.