Next Article in Journal
An Overview of Solid Acid Catalysts in Lignocellulose Biorefineries
Previous Article in Journal
Fe or Ni Catalytic Hydrothermal Depolymerization with Ethanol for Efficient Anaerobic Digestion of Corn Stover
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

The Effect of Surfactant P123 on the KCuLaZrO2 Catalysts in the Direct Conversion of Syngas to Higher Alcohols

1
College of Chemical Engineering and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, China
2
Guangdong Sinoplast Advanced Material Co., Ltd., Dongguan 523860, China
*
Authors to whom correspondence should be addressed.
Catalysts 2025, 15(5), 431; https://doi.org/10.3390/catal15050431
Submission received: 10 March 2025 / Revised: 10 April 2025 / Accepted: 23 April 2025 / Published: 28 April 2025

Abstract

:
The direct conversion of coal-based syngas to HA (higher alcohols) is of great significance, but it remains challenging stemming from the complexity of the reaction and the difficulty in regulating the alcohol distribution. P123, as a structure-directing agent, is of great significance for the preparation of mesoporous materials with specific pore sizes and pore structures. Therefore, a series of KCLZ-xP (KCuLaZrO2-xP123) catalysts with varying P123 contents were prepared via the coprecipitation method and applied for HA synthesis. The KCLZ-30P catalyst exhibits a high CO conversion of 63.1%, a C2+OH/MeOH ratio of 0.98, and a comparable STYROH (space-time yield of total alcohol). Notably, it can selectively form linear alcohols in HAS while suppressing the formation of i-C4 (branched alcohols). The results show that P123 remarkably boosts catalytic activity through enlarging the specific surface area and facilitating the generation of t-ZrO2. Simultaneously, P123 suppresses the formation of i-C4 alcohols by reducing the number of basic sites and weakening the strength of high-strength basic sites. Remarkably, the abundant CHx and non-dissociated CO adsorbed on Cu0 facilitate the CO insertion process, thereby enhancing the C-C chain growth capability in linear alcohols, particularly favoring the formation of ethanol. These findings may offer the potential designing efficient catalysts for HAS (higher alcohol synthesis) from syngas.

Graphical Abstract

1. Introduction

Coal, as an irreplaceable primary energy source, plays a role in providing a backup for the construction of a new energy system. The clean and efficient utilization of coal is of great significance in promoting the high-quality development and green low-carbon transformation of the coal industry in the new era [1,2,3]. HA (C2+OH) has drawn significant attention due to its widespread use as a synthetic fuel, alternative fuel additive, hydrogen carrier, and pharmaceutical [4,5,6]. The direct thermal catalytic conversion of coal-based syngas (CO/H2) into higher alcohols is one of the effective ways to alleviate the shortage of energy resources and increasingly serious environmental problems. Nevertheless, there are still significant challenges in developing highly efficient and stable catalysts for industrialization due to technical difficulties such as complex synthesis reactions and multiple by-products.
As is well known, the HAS is directed from syngas via the CO insertion mechanism, in which the insertion of undissociated adsorbed CO* into the CnHx* formed by CO dissociation is the most critical step. Although the HAS process is thermodynamically favorable, the formation of HA will be kinetically controlled due to the presence of many different chemical reactions [7,8,9]. Until now, five types of heterogeneous catalysts have extensively explored for HAS: (a) Rh-based catalysts, (b) modified methanol synthesis catalysts (high-temperature ZnCr catalysts and low-temperature Cu-based catalysts), (c) modified F-T synthesis catalysts, (d) Mo-/MoS2-based catalysts, and (e) tandem catalysts [10,11,12,13]. Among them, the supported non-precious metal Cu/ZrO2 catalysts are of particular interest, owing to the high activity, the great total alcohol selectivity (lower hydrocarbons), and a superior cost advantage. In the Cu/ZrO2 catalyst systems, ZrO2 with high thermal stability plays a role in supporting and dispersing active metals, and it can also generate unique interactions with Cu species. Typically, the copper active sites are responsible for dissociating the adsorbed H2 and non-dissociating adsorbed CO* and transferring the adsorbed species to ZrO2, where the alcohol is generated [14,15]. Scotti and co-workers observed that highly dispersed Cu species are generated on a high surface area ZrO2, which achieved a superior catalytic activity [16]. Wu et al. prepared Fe promoted CuZrO2-based catalyst showed higher total alcohol STY and isobutanol selectivity, which were ascribed to the greatest quantity of weak CO adsorption and basic sites [17]. They also proposed that the addition of La enhances the Cu-Zr synergistic interaction, leading to significantly improved catalytic activity. This enhancement is attributed to both the increased reducibility of the catalyst and the higher dispersion of Cu species [18]. Some studies have revealed that the Cu-La interface is conducive to the formation of stable Cu+ species, which played a crucial role in the formation of C2+ alcohols [19,20]. In brief, the formation of C2+ alcohols strongly depends on the Cu-Zr interaction. Despite these efforts, Cu/ZrO2 catalysts still encounter some significant challenges, including lower alcohol yield, high selectivity for CO2 and CHx, and poor catalyst stability.
Notably, an important strategy in the synthesis of higher alcohol from syngas is to add non-metallic surfactants to regulate the electronic and geometric structure of catalysts [11,21,22]. P123 (PEO20PPO70PEO20—EO represents ethoxy, and PO represents propoxy) is a triblock non-ionic surfactant that can be used as a template for preparing catalysts with mesoporous structures. The effect of P123/Cu-Zn-Zr molar ratio on the conversion of CO2 to methanol was recently studied by Marcos et al. [23]. It was demonstrated that a higher surfactant ratio can optimize the Cu+/0 and ZnO-ZrO2 physicochemical properties. Liu et al. designed ordered mesoporous NiMo-Al2O3 catalysts using P123 as a structure-directing agent to regulate its textural properties, resulting in different metal–support interactions [24]. Ganiyu et al. observed that the P123-assisted preparation of the Ti-SBA-15 HDS catalyst exhibited improved dispersion, textural properties, and surface acidity, which are mainly accounted for in the outstanding catalytic activities [25]. Han et al. utilized ionic surfactant P123 as the template to regulate the morphology and construct prism-like silica tubes with mesoporous membranes [26]. Nonetheless, to the utmost extent of our awareness, there is scarce research on the impact of P123 as an additive on the pore structure and active components of Cu/ZrO2 catalysts.
Herein, we aimed to improve the specific surface area and regulate the alcohol distribution by introducing template P123 during the coprecipitation process. For this purpose, a series of KCuLaZrO2 catalysts with different contents of P123 were designed and applied for HAS from syngas. Combining multiple characterizations, the structure and chemical state of KCLZ-xP catalysts and their impact on alcohol distribution were systematically studied. Furthermore, our comprehensive characterization provided valuable insights into the active sites within the KCLZ-xP catalyst, as well as the crucial factors that influence the reaction routes toward HA. This research will enhance the level of catalyst technology for the synthesis of HA from syngas.

2. Results

2.1. Catalytic Performance

To study the catalytic performance of the KCLZ-xP catalysts, HAS was evaluated at 350 °C and 5 MPa with syngas (H2/CO = 2.5), and the results are shown in Table 1. Figure 1A,B intuitively present the alcohol distribution and CO conversion, i.e., C2+OH/MeOH of the KCLZ-xP catalysts, respectively. A gradual increase in P123 leads to a significant increase in CO conversion (XCO) from 19.3% to 63.1%. Meanwhile, the impact of P123 on STYROH is minimal and almost unchanged. Compared with the KCLZ catalyst without P123, all KCLZ-xP (x = 10–30) catalysts exhibited lower ROH selectivity. However, the space-time yield of gaseous products (STYgas) increases sharply from 77 to 528 g/(L·h). This is mainly due to the fact that the selectivities of both CHx and CH4 have been increased to nearly twice, indicating that the introduction of P123 is conducive to the formation of a CHx intermediate. In the upcoming discussion, we will examine the reasons that give rise to this phenomenon. In the distribution of alcohols, the selectivity of branched-chain alcohols, namely isobutanol (i-C4), decreased monotonously from 9.3 to 3.1 wt%, while the selectivity of straight-chain alcohols increased gradually. It can be seen intuitively from Figure 1 that the addition of P123 leads to an increase in C2+OH/MeOH from 0.51 to 0.98, notably boosting ethanol selectivity from 12.0 to 27.2 wt%. Figure 2 shows the ASF plot of alcohols and the corresponding chain-growth probability (α) of the KCLZ-xP catalysts. It is also found that the distribution of alcohol products is closer to classical ASF distribution with the increase in P123 content [27]. It is noteworthy that, compared to the KCLZ catalyst (0.28), the chain-growth probability (α) of KCLZ-30P is as high as 0.32. These results strongly indicated that the KCLZ-xP catalysts with higher P123 content can effectively suppress the formation of CH3OH and exhibit an enhanced carbon chain growth capability.

2.2. Physicochemical Properties of Catalysts

To investigate the influence of the surface structure on the reaction, we further calculated the N2 physical adsorption of all the catalyst powders and summarized the results in Table 2. As the amount of P123 increases, the SBET significantly increased from 82.58 m2/g to the highest 91.65 m2/g, and then decreased to 72.75 m2/g by further increasing the P123 to 30 g. This may be attributed to the removal of P123 during the calcination process of the catalysts, which resulted in the formation of more porous structures. As the P123 content increased to 30 g, the SBET significantly reduced, which is possibly because the collapse of some pores caused by the continuous decomposition of higher P123 during the calcination process. After the introduction of P123 into the KCLZ-xP catalysts, no change in the pore volume was observed, and it remained at 0.1 cm3/g. In addition, the average pore size of the KCLZ-xP catalyst slightly increases from 3.15 to 3.79 nm. As depicted in Figure 3A, a type IV adsorption isotherms with an H2-type hysteresis loops are observed in all KCLZ-xP catalysts, indicating the preservation of the typical characteristics of “inkbottle” structure and mesoporous materials [28]. The narrow pore size distribution concentrated at 3–4 nm was exposed in all KCLZ-xP catalysts, as shown in Figure 3B. In other words, the large specific surface area and mesoporous properties facilitate the generation of more active sites, enabling reactant molecules to quickly adsorb on the active sites and allowing the formed molecules to depart promptly.

2.3. XRD

Crystallinity and phase patterns were performed to investigate the effect of P123 on HAS. XRD patterns of calcined and reduced KCLZ-xP catalysts are shown in Figure 4A and Figure 4B, respectively. As displayed in Figure 4A, a relatively broad diffraction peak in the range of 28–38° for the calcined KCLZ-xP catalysts are unambiguously indexed to amorphous ZrO2 (am-ZrO2) [29,30]. Remarkably, it can be seen that the KCLZ-30P catalyst has distinct diffraction peaks around 30.3°, 50.3°, and 60.2°, which were attributed to tetragonal ZrO2 (t-ZrO2, JCPDS 50–1089) [17]. In other words, as the content of P123 increases, the presence of am-ZrO2 in the calcined KCLZ-xP catalyst is accompanied by the emergence of t-ZrO2, indicating that the introduction of P123 promotes the formation of t-ZrO2. No phases attributed to CuO and La2O3 were observed in the calcined KCLZ-xP catalysts, which may be due to the high dispersion of CuO and the low loading amount of La2O3.
For reduced KCLZ-xP catalysts (Figure 4B), ZrO2 mainly exhibited amorphous form when the P123 content is less than 20 g, similar to the calcined KCLZ-xP catalysts. Interestingly, new visible peaks related to t-ZrO2 appeared completely in the KCLZ-30P catalyst, which again proved that P123 above 20 g was conducive to the formation of t-ZrO2. Since the specific surface area of am-ZrO2 (100–300 m2/g) is significantly higher than that of t-ZrO2 (10–50 m2/g), which accounts for the changes in SBET observed in Table 2 [12,31]. All reduced KCLZ-xP catalysts displays the distinct peaks around 2θ of 43.5°, 50.4°, 73.9°, characteristic of metallic Cu0 (JCPDS 04–0836) [10]. It might be considered that the CuO crystallite transforms into metallic Cu after the reduction. In addition, the diffraction peaks assigned to metallic Cu0 became stronger as the amount of P123 (0–20 g) increases, indicating that the Cu0 particles size increased with the increase of P123. By contrast, the diffraction peak intensity of metallic Cu0 is significantly weakened when the P123 content is 30 g. It is further validated that metallic Cu0 is highly dispersed on the surface of the KCLZ-30P catalyst, which expectedly improved the activation of H2 and the formation of HA [32,33].

2.4. H2-TPR

To investigate the reduction process of Cu species on the surface, the KCLZ-xP catalysts were explored by H2-TPR, as shown in Figure 5. It should be explained that ZrO2 and La2O3 will not be reduced under reduction conditions, so we believe that the hydrogen consumption peaks only represent the reduction of Cu species. In view of KCLZ catalyst, three overlapped reduction peaks are indicative of the presence of three Cu species with different chemical environments. Among them, the reduction peaks at the lower temperatures of 107 °C and 117 °C were attributed to the reduction of well-dispersed and dispersed CuO species [34,35]. The broad reduction peaks located around 155 °C were assigned to a consecutive reduction of bulk CuO to Cu0. As the P123 content increased to 10 g, three hydrogen consumption peaks still persist and all shift towards higher temperatures. When P123 is further increased from 10 g to 30 g, a single low-temperature reduction peak emerges, and all reduction peaks shift towards higher temperatures. Previous studies have shown that the interaction (Cu-O-Zr) between finely dispersed CuO species and am-ZrO2 promotes the reduction of CuO [36,37]. According to H2-TPR, the reduction temperature gradually shifted toward higher temperature with an increase in P123 content, which means that the reduction of CuO is more difficult. Based on the XRD results, this may be due to the decrease in am-ZrO2 caused by P123, which reduces the Cu-O-Zr interaction between finely dispersed CuO and am-ZrO2, making the reduction of CuO more difficult [12].

2.5. CO, CO2, NH3-TPD

The CO-TPD was carried out to investigate the adsorption and desorption behavior of CO over the reduced KCLZ-xP catalysts. As shown in Figure 6, all KCLZ-xP catalysts display two wide CO desorption peaks around 262 °C and 486 °C, corresponding to non-dissociative adsorption CO and dissociative adsorption CO, respectively [17]. The KCLZ catalyst possesses a significantly higher density of non-dissociative adsorption CO sites compared to the other three catalysts. The content of different CO adsorption sites in reduced KCLZ-xP catalysts is shown in Table 3. It is distinctly observable that when the content of P123 increases from 0 to 10 g, the proportion of strong CO adsorption sites significantly increases from 30% to 47%. However, the proportion of strong CO adsorption decreases slightly to 44% when P123 increases to 30 g. Additionally, the introduction of P123 does not induce any temperature shift in the CO desorption peaks, indicating that P123 has no obvious effect on the adsorption strength of CO.
The surface acidity and basicity of the catalyst are of great significance in the growth of carbon chains and the formation of alcohols in the process of CO hydrogenation. As displayed in Figure 6B,C, the surface acidity and alkalinity of the KCLZ-xP catalysts were detected by CO2-TPD and NH3-TPD, respectively. Table 3 lists the contents of three different basic sites on the KCLZ-xP catalyst surface, including weak-strength basic sites (50–200 °C), medium-strength basic sites (300–500 °C) and high-strength basic sites (580–700 °C). Compared with KCLZ, the KCLZ-xP catalyst with P123 showed an increase density of weak-strength basic sites. By contrast, the content of medium-strength basic sites over KCLZ-xP catalyst with P123 is lower than that of KCLZ. Notably, as the P123 increases, the high-temperature desorption peak of CO2 (622 °C) gradually shifts toward lower temperatures, indicating that P123 weakened the strength of high-strength basic sites. Altogether, the number of high-strength basic sites and total basic sites decreased with the increase in P123.
Figure 6C shows the NH3-TPD profiles of different catalysts. All KCLZ-xP catalysts display three NH3 desorption peaks, corresponding to weak-strength acid sites (124 °C), medium-strength acid sites (378 °C), and high-strength acid sites (583 °C). It was clearly observed that the KCLZ catalyst exhibited a significantly higher density of weak-strength acid sites than that of the other three catalysts. Additionally, the amounts of medium-strength acid sites decreased slightly with the increase in P123. Compared with KCLZ catalyst, the NH3 desorption peak around 583 °C shifts to higher temperature after the introduction of P123, accompanied by a decrease in density. It indicates that P123 enhances the acidity of high-strength acid sites, which may be caused by the high lack of electron Zr4+ or Cu+. The highly electron-deficient Zr4+ or Cu+ species facilitate CO adsorption and activation, which is responsible for explaining why the significant enhancement in catalytic activity with the increase in P123. These reports were in great coincidence with the CO-TPD obtained here.

2.6. XPS

We used a surface sensitive technique XPS to obtain surface information about the composition, chemical state, and electronic structure on the reduced catalyst. The XPS patterns of Zr 3d, O 1s, Cu 2p, and Cu LMM regions of the catalysts were shown in Figure 7. As presented in Figure 7A, the Zr 3d3/2 and Zr 3d5/2 of KCLZ-xP catalysts locate at approximately 184.2 and 181.8 eV, respectively, with a disparity of 2.4 eV, which are in good accordance with the reported data of Zr4+ [38,39,40]. At the same time (Figure 7B), the oxygen species with binding energy at 531.3 eV was attributed to the hydroxyl species (OH), and the oxygen species at a lower binding energy of 529.9 eV was attributed to the lattice oxygen species (OL) [41]. The surface OH can react with CO to generate C1 species (CHxO), which is also an important intermediate in the process of alcohol formation [17]. And then, as shown in Figure 7C, the Cu 2p spectra presented two prominent peaks at around 954.7 and 934.5 eV, which corresponded to Cu 2p1/2 and Cu 2p3/2, respectively. Moreover, the lack of satellite peaks within the binding energy range of 940–945 eV indicated that all Cu2+ species had been reduced to Cu+ or Cu0 at 360 °C. To gain further insights, the Cu LMM XAES spectra were obtained (Figure 7D). It was observed that the broad and asymmetrical peak centered at around 916.8 eV and 913.5 eV, which was assigned to Cu0 and Cu+ species, respectively [42]. The proportions of Cu+ species (XCu+) obtained after peak deconvolution are summarized in Table 2. Combined with the XRD results, Cu0 and Cu+ species coexisted on the surface of reduced KCLZ-xP catalysts.

2.7. In Situ CO-DRIFTS

The aim for a better understanding of the surface chemistry on the KCLZ-xP catalysts with different P123 contents, in situ CO-DRIFT spectroscopy was exploited. Figure 8 and Figure 9 show the in situ CO-DRIFT spectra in the high-frequency range of 2175–2025 cm−1 and the low-frequency range of 1850–1150 cm−1, respectively. Compared with Cu0 and Cu2+ species, CO-Cu+ has stronger interaction and thermal stability [43]. Therefore, the stable peak approximately at 2104 cm−1 for the KCLZ-xP catalysts is likely to be related to the existence of Cu+-CO carbonyls, which act as the predominant species [39,44], while the bands at 2004 cm−1 are considered to be due to the CO adsorbed on Cu0 [45]. In the case of KCLZ catalyst, the peak at 1640 cm−1 is ascribed to the bridged bicarbonate species (b-HCO3), which serves as evidence that CO had reacted with the surface OH groups, leading to the formation of C1 species [17,39]. Another peak appearing at 1578 cm−1 could be possibly linked to the O-C-O asymmetric stretching vibration of bidentate formate species (b-HCOO) [30,46,47]. Additionally, the peak at 1308 cm−1 has been identified as corresponding to the result of the overlap of formate (b-HCOO-Cu, 1350 cm−1) and bridged bidentate carbonates (b-HCO3, 1250 cm−1) [30,39], whereas the absorption peak at 1067 cm−1 is ascribed to C-O stretching vibrations of methoxyl species [48]. Upon increasing the P123 content to 20 g, the intensity of the absorption peaks linked to HCO3 and HCOO increased significantly. However, for the KCLZ-30P catalyst, the intensity of the absorption peaks associated with HCO3 and HCOO decreased significantly, especially for the HCOO species. At the same time, a new absorption peak appeared at about 1520 cm−1 of the KCLZ-30P catalyst, which was the characteristic peak of monodentate carbonate species (m-CO32−) [39]. According to the above results, we found that increasing P123 caused the characteristic peak of all species on the catalyst surface increased first and then decreased, which may be related to the change in the specific surface area of the catalyst (SBET result).

3. Discussion

According to the catalytic performance evaluation, an increase in P123 content led to CO conversion increasing linearly. The BET analysis showed that when the content of P123 increased from 0 to 20 g, the SBET gradually increased. This suggests that the number of active sites exposed on the catalyst surface increases, which is conducive to the improvement in CO conversion. Although the SBET of KCLZ-30P catalyst decreased slightly, XRD demonstrated that KCLZ-30P catalyst exhibited obvious t-ZrO2 compared with other catalysts, which is an effective active site for the formation of CHx intermediates [49]. On the other hand, in situ DRIFTS showed that the content of the CO32− species on the KCLZ-30P catalyst was significantly increased. Due to the good stability of the CO32− species, they are prone to undergoing excessive hydrogenation, leading to the formation of hydrocarbons, which is also a reason for the improved CO conversion. In other words, when the addition amount of P123 is 0–20 g, the large specific surface area is the main reason for the activity improvement, whereas when P123 is 30 g, the t-ZrO2 and highly stable CO32− species become the key factor for the further enhancement of activity.
Regarding the selectivity for total alcohols, it shows a decreasing trend with the introduction of P123, while the selectivity for CO2 and hydrocarbons (CHx and CH4) increase significantly. In particular, the selectivity for hydrocarbon products increases from 25% to 47.6%. There are the following three points to explain this phenomenon: Firstly, the XRD of the reduced catalyst confirms that the introduction of P123 significantly increases the particle size of metal Cu, leading to the formation of hydrocarbons. Some researchers have proposed that a smaller Cu particle size was beneficial for the dissociation and adsorption of H2, while a larger Cu particle size was beneficial to the C-O bond dissociation for CHx formation [33,37]. Secondly, the CO-TPD results indicate that the introduction of P123 increases the amount of strongly adsorbed CO on the catalyst surface, which tends to undergo over-hydrogenation, resulting in C-O bond cleavage to form CHx species, thus facilitating the generation of hydrocarbon products. Thirdly, NH3-TPD also revealed that the introduction of P123 significantly increased the content of medium-strength acid sites and notably enhanced the acidity of high-strength acid sites. The strong acidity will enhance the dissociation adsorption of CO and further hydrogenation ability, thereby increasing the selectivity of hydrocarbons [17,50].
From the alcohol product distribution, the KCLZ catalyst without P123 exhibits a relatively high selectivity for branched alcohols (i-C4), reaching 9.3 wt%. As the P123 content increased, the selectivity for i-C4 gradually decreased, while the selectivity for linear alcohols progressively increased. Notably, the selectivity for ethanol increased linearly from 12 wt% to 27.2 wt%, and the C2+OH/MeOH ratio rose from 0.51 to 0.98, indicating that the introduction of P123 favors carbon chain growth in linear alcohols. On the one hand, the decline in i-C4 selectivity can be ascribed to the decline in the number of basic sites and the weakened strength of strong basic sites, which leads to the obstruction of the formation of i-C4 alcohols (via the condensation reaction pathway) [50]. On the other hand, CO-TPD and NH3-TPD indicate that the addition of P123 stimulates the formation of CHx species. Meanwhile, in situ DRIFTS reveals the enhanced adsorption of non-dissociative CO on Cu0 species. This means that the process of CO insertion into CHx is facilitated, thereby promoting the formation of linear alcohols. In addition, according to the results of XRD and XPS, both Cu+ and Cu0 species coexist on the reduced catalysts and the synergistic effect of Cu+-Cu0 is crucial for CO hydrogenation to ethanol [10]. Meanwhile, He et al. found that the presence of t-ZrO2 facilitates the formation of ethanol [49]. Excessive P123 tends to form overly dense micellar networks, which may lead to pore channel collapse or disordering after calcination, resulting in reduced specific surface area and metal agglomeration. Additionally, the incomplete decomposition of excessive P123 can leave residual carbon deposits covering the pore surfaces. In conclusion, the introduction of P123 into the CuZr-based catalyst not only significantly influences the structure and surface properties but also alters the alcohol product distribution by reducing the formation of i-C4 alcohols while promoting the generation of linear alcohols (especially ethanol).

4. Materials and Methods

4.1. Catalyst Preparation

All chemical reagents used in the preparation process of catalysts are analytically pure. A series of KCuLaZrO2 catalysts with different P123 content were facilely prepared via the coprecipitation method. Firstly, Cu(NO3)2·3H2O, La(NO3)3·6H2O and ZrOCl2·8H2O with a molar ratio of n(Cu):n(La):n(Zr) = 1:0.1:4.5 were dissolved in deionized water, and the resulting acidic solution was labeled as solution A. Meanwhile, an aqueous solution of KOH (1 mol/L) was prepared, and the obtained alkaline solution was labeled as solution B. Next, different weights of P123 were dissolved in 1000 mL distilled water, followed by adding the above mixed solution A and B dropwise under vigorous magnetic stirring (60 °C) at a pH of around 11. At the end of the coprecipitation reaction, the suspension was kept to age at room temperature for 3 h. Then, the precipitate was washed and filtered off several times with deionized water until there were no Cl ions in the filtrate. Afterwards, the obtained blue precipitate was dried overnight at 120 °C and calcined at 400 °C for 4 h. Finally, the synthesized KCuLaZrO2-xP123 catalysts were abbreviated as KCLZ, KCLZ-10P, KCLZ-20P, and KCLZ-30P catalysts, representing the weight of P123 as 0, 10, 20, and 30 g, respectively. All the calcined catalysts were granulated, crushed, and sieved to 30–40 mesh for catalytic activity tests.

4.2. Catalyst Characterization

The N2 physisorption experiments were carried out using a Micromeritics Tristar 3000 physisorber (Shanghai, China). The specific surface area (SBET), pore volume (Vp), and pore size distributions were determined by the Brunauer–Emmett–Teller (BET) method and Barrett–Joyner–Halenda (BJH) method using the desorption branch of the isotherms, respectively.
X-ray diffraction (XRD) patterns of tested catalysts were obtained on a Rigaku SmartLab diffractometer using Ni-filtered Cu-Kα (40 kV and 100 mA) radiation (Tokyo, Japan). The catalysts were scanned in the range of 2θ = 5–80° with a scanning speed of 4°/min.
Temperature-programmed desorption (H2-TPR, CO, CO2, NH3-TPD) patterns were recorded on a BELCAT-B instrument (BEL JAPAN, Inc., Osaka, Japan). H2-TPR: Prior to each test, the catalyst was purged in Ar at 350 °C for 30 min to remove impurities adsorbed on the surface. After cooling to 50 °C in Ar, the catalyst was heated from 50 to 800 °C, with a heating rate of 10 °C/min under 10% H2/Ar flow. CO, CO2, NH3-TPD: The catalyst was treated in the flow of 10% H2/Ar at 350 °C for 30 min to ensure complete surface reduction, followed by flushing with Ar to remove the residual H2 on the surface. After cooling to 50 °C in Ar, the catalyst was exposed to adsorbed gas (CO, CO2, and NH3) until full saturation. Finally, increasing the temperature to 800 °C at a heating rate of 10 °C/min under Ar flow. The thermal conductivity detector (TCD) signal was recorded automatically to track adsorbed gas consumption.
X-ray photoelectron spectroscopy (XPS) measurement was conducted on a K-Alpha apparatus (Thermo Fisher Scientific, Waltham, MA, USA) with an Al Kα (hv = 1486.6 eV, 12 kV and 6 mA) radiation. The binding energy (BE) of C 1s (284.6 eV) was used to calibrate all XPS spectra.
In situ CO diffuse reflectance infrared Fourier transform (in situ CO-DRIFTS) measurements were executed on a Bruker Tensor 27 infrared spectrometer (Karlsruhe, Germany). Prior to measurement, the reduction process was performed on each catalyst by passing 10% H2/N2 at a flow rate of 15 mL/min. Later on, it was switched to Ar to purge the in situ cell, and we recorded the background signal at 350 °C. After that, the corresponding spectrum was collected every 3 min in CO atmosphere. The temperature was reduced from 350 to 50 °C, and the spectra were collected again under Ar stream for 30 min.

4.3. Catalytic Performance Evaluation

The catalytic performance of the KCLZ-xP catalysts (5 mL, 30–40 mesh) was evaluated in a continuous flow fixed-bed reactor (Shanxi Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan City, Shanxi Province, China). The mass flow controller was set to control the syngas flow rate, while the wet flowmeter was utilized to regulate the tail gas flow rate. In each operation, the catalyst was loaded into a stainless-steel tubular reactor and activated in 10% H2/N2 at 350 °C and atmospheric pressure for 6 h. After reduction, the temperature was kept at 350 °C, and the gas was switched to syngas (H2/CO = 2.5), with WHSV of 3000 h−1 at the 5 MPa. After stabilizing for 10 h, the products were collected after passing through a cold trap. H2, CO, CH4, and CO2 in the feed gas and tail gas were quantified by carbon molecular sieve column with a thermal conductivity detector (TCD, GC4000A) (Beijing Changliu Scientific Instruments Co., Ltd., Beijing, China), while the hydrocarbons, DME, and CH3OH were detected by GDX-403 column with a flame ionization detector (FID, GC4000A) (Beijing Changliu Scientific Instruments Co., Ltd., Beijing, China). A GDX-401 column (GC4000A) with a TCD was utilized for analyzing the H2O, methanol, and alcohol in effluent products. A Chromosorb 101 column (GC-2010) with an FID was utilized for detecting alcohol products.
CO conversion (XCO), product selectivity on carbon basis (Si) and the mass selectivity of alcohol i in alcohol products (Wi) can be calculated based on the following formula [11,19].
X CO = n CO , in n CO , out n CO , in × 100 %
S i = v i × n i , out   n i , in n CO , in   n CO , out × 100 %
W i = R i , s f i , m i R i , s f i , m × 100 %
The nCO,in and nCO,out represent the moles of CO at the inlet and outlet, respectively. Si and vi stands for the selectivity of C mol and carbon number of the products, such as hydrocarbons, DME and CO2. Ri,s and fi,m represent the area ratio of alcohol i on the chromatogram and quality correction factor, respectively.
The Anderson–Schulz–Flory (ASF) model is used to describe the relationship between chain growth probability and the number of carbons in alcohol product distribution. The chain-growth probability (α) of product was calculated according to the following equation:
ln ( W n i n ) = n   ln α + 2   ln ( 1 α α )
where n and Wni represented the carbon number of product i and the mass fraction of product i, respectively.

5. Conclusions

In this work, the structure–activity relationship of CO hydrogenation on CuZr catalyst was constructed by studying the effect of introducing P123 on the surface properties and chemical environment of KCLZ-xP catalyst. When the content of P123 increases to 20 g, the specific surface area of the catalyst increases. Further increasing the content of P123 to 30 g promotes the formation of t-ZrO2. All of these are beneficial for improving the CO conversion. The decrease in total alcohol selectivity and the increase in CO2 and hydrocarbon selectivity are due to the introduction of P123, which leads to the appearance of large particles metal Cu, an increase in strong CO adsorption sites, and an enhancement of the acidity of strong acid sites, all of which are conducive to the formation of more CHx species. In the distribution of alcohols, due to the decrease in basic sites and the weakening of the alkalinity of strong basic sites, the branched alcohol (i-C4) selectivity decreases. This is also the most unique point compared to the previous K-CuZnZrO2, KFeCuZrO2, and Cu-ZrO2 catalysts [12,17]. The enhanced non-dissociated adsorption of CO* species on Cu0, combined with abundant CHx species, promoting the insertion of non-dissociated CO* into CHx, resulting in increased selectivity for linear alcohols (especially ethanol). In summary, the strategy of regulating KCuLaZrO2 catalysts through surfactant P123 provides a new approach for designing high-performance HAS catalysts.

Author Contributions

Conceptualization, J.Y. and K.S.; formal analysis, J.Y. and J.J.; writing—original draft preparation, J.Y. and Z.W.; writing—review and editing, J.Y. and D.X.; supervision, L.Z.; funding acquisition, J.Y. and K.S. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi, STIP (2023L181), the Fundamental Research Program of Shanxi Province (No. 202203021221155, 202303021222180).

Data Availability Statement

The raw data supporting the conclusions of this article will be made available by the authors on request.

Acknowledgments

The author sincerely thanks the key laboratory of catalytic conversion energy coupling in Shanxi Province and Shanxi Institute of Coal Chemistry, Chinese Academy of Sciences for their support.

Conflicts of Interest

Author Zhongqiang Wang was employed by the company Guangdong Sinoplast Advanced Material Co., Ltd. The remaining authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

References

  1. Liu, G.; Yang, G.; Peng, X.; Wu, J.; Tsubaki, N. Recent advances in the routes and catalysts for ethanol synthesis from syngas. Chem. Soc. Rev. 2022, 51, 5606–5659. [Google Scholar] [CrossRef] [PubMed]
  2. Liu, S.; Wu, D.; Zhao, Y.; Liang, Y.; Zhang, L.; Sun, J.; Lin, J.; Wang, S.; Yao, Y.; Wan, S.; et al. Recent advances and perspectives in catalyst design for converting syngas to higher alcohols. Energy Fuels 2024, 38, 14769–14796. [Google Scholar] [CrossRef]
  3. Gong, N.; Wu, Y.; Ma, Q.; Tan, Y. A simple strategy stabilizing for a CuFe/SiO2 catalyst and boosting higher alcohols’ synthesis from syngas. Catalysts 2023, 13, 237. [Google Scholar] [CrossRef]
  4. Wang, C.; Lin, T.; Qi, X.; Yu, F.; Lu, Y.; Zhong, L.; Sun, Y. Direct conversion of syngas to higher alcohols over multifunctional catalyst: The role of copper-based component and catalytic mechanism. J. Phys. Chem. C 2021, 125, 6137–6146. [Google Scholar] [CrossRef]
  5. Shui, M.; Huang, C.; Ma, P.; Li, W.; He, Q.; Wu, W.; Tan, Y.; Bao, J. Accelerating C2+ alcohols synthesis from syngas by simultaneous optimizations of CO dissociation and chain growth over CuCo alloy catalyst. Chin. Chem. Lett. 2021, 32, 2203–2206. [Google Scholar] [CrossRef]
  6. Zhu, C.; Xu, K.; Fang, Y.; Lv, Q.; Jiang, K.; Zhao, H.; Chen, Y.; Wang, P.; Yang, H.; Wu, L.; et al. Synergetic effect of Ce/Zr for ethanol synthesis from syngas over Rh-based catalyst. Fuel 2023, 334, 126770. [Google Scholar] [CrossRef]
  7. Gupta, M.; Smith, M.; Spivey, J. Heterogeneous catalytic conversion of dry syngas to ethanol and higher alcohols on Cu-based catalysts. ACS Catal. 2011, 1, 641–656. [Google Scholar] [CrossRef]
  8. Spivey, J.; Egbebi, A. Heterogeneous catalytic synthesis of ethanol from biomass-derived syngas. Chem. Soc. Rev. 2007, 36, 1514–1528. [Google Scholar] [CrossRef]
  9. Suárez París, R.; Lopez, L.; Barrientos, J.; Pardo, F.; Boutonnet, M.; Järås, S. Catalytic conversion of biomass-derived synthesis gas to fuels. Catalysis 2015, 27, 62–143. [Google Scholar]
  10. Yang, J.; Gong, N.; Wang, L.; Wu, Y.; Zhang, T.; Xie, H.; Yang, G.; Tan, Y. Tuning the Cu+ species of Cu-based catalysts for direct synthesis of ethanol from syngas. New. J. Chem. 2021, 45, 20832–20839. [Google Scholar] [CrossRef]
  11. Yang, J.; Gong, N.; Wang, L.; Wu, Y.; Zhang, T.; Zeng, C.; Tan, Y. Insights into the one-step ethanol synthesis through CO hydrogenation over surfactant-assisted preparation of CuCo/SiO2 catalyst. Fuel 2022, 327, 125078. [Google Scholar] [CrossRef]
  12. Gong, N.; Zhang, T.; Tan, M.; Wang, L.; Yang, J.; Tan, L.; Yang, G.; Wu, P.; Wu, Y.; Tan, Y. Realizing and revealing complex isobutyl alcohol production over a simple Cu-ZrO2 catalyst. ACS Catal. 2023, 13, 3563–3574. [Google Scholar] [CrossRef]
  13. Shi, G.; Zhang, X.; Li, X.; Hou, C.; Guo, Y.; Jiao, W. Facile synthesis of super-microporous mesoporous MgO-ZrO2 composites and their adsorption properties for CO2. Chem. Phys. 2024, 583, 112319. [Google Scholar] [CrossRef]
  14. Fisher, I.; Bell, A. In-Situ infrared study of methanol synthesis from H2/CO2 over Cu/SiO2 and Cu/ZrO2/SiO2. J. Catal. 1997, 172, 222–237. [Google Scholar] [CrossRef]
  15. Fisher, I.; Woo, H.C.; Bell, A. Effects of zirconia promotion on the activity of Cu/SiO2 for methanol synthesis from CO/H2 and CO2/H2. Catal. Lett. 1997, 44, 11–17. [Google Scholar] [CrossRef]
  16. Scotti, N.; Zaccheria, F.; Evangelisti, C.; Psaro, R.; Ravasio, N. Dehydrogenative coupling promoted by copper catalysts: A way to optimise and upgrade bio-alcohols. Catal. Sci. Technol. 2017, 7, 1386–1393. [Google Scholar] [CrossRef]
  17. Wu, Y.; Wang, H.; Wang, L.; Gong, N.; Yang, J.; Zhang, T.; Xie, H.; Tan, Y. Effect of iron on ZrO2-based catalysts for direct synthesis of isobutanol from syngas. Fuel 2021, 304, 121342. [Google Scholar] [CrossRef]
  18. Wu, Y.; Xie, H.; Tian, S.; Tsubaki, N.; Han, Y.; Tan, Y. Isobutanol synthesis from syngas over K-Cu/ZrO2-La2O3(x) catalysts: Effect of La-loading. J. Mol. Catal. A Chem. 2015, 396, 254–260. [Google Scholar] [CrossRef]
  19. Yang, J.; Gong, N.; Wang, L.; Wu, Y.; Zhang, T.; Tan, Y. Effect of La2O3-decorated SiO2 on the performance of CuCo catalyst for direct conversion of syngas to ethanol. Fuel 2022, 319, 123811. [Google Scholar] [CrossRef]
  20. Brown Bourzutschky, J.; Homs, N.; Bell, A. Conversion of synthesis gas over LaMn1-xCuxO3+λ perovskites and related copper catalysts. J. Catal. 1990, 124, 52–72. [Google Scholar] [CrossRef]
  21. Chu, Z.; Chen, H.; Yu, Y.; Wang, Q.; Fang, D. Surfactant-assisted preparation of Cu/ZnO/Al2O3 catalyst for methanol synthesis from syngas. J. Mol. Catal. A Chem. 2013, 366, 48–53. [Google Scholar] [CrossRef]
  22. Shen, J.; Bai, Y.; Tai, X.; Wang, W.; Wang, G. Surface activity, spreading, and aggregation behavior of ecofriendly perfluoropolyether amide propyl betaine in aqueous solution. ACS Sustain. Chem. Eng. 2018, 6, 6183–6191. [Google Scholar] [CrossRef]
  23. Marcos, F.; Lin, L.; Betancourt, L.; Senanayake, S.; Rodriguez, J.; Assaf, J.; Giudici, R.; Assaf, E. Insights into the methanol synthesis mechanism via CO2 hydrogenation over Cu-ZnO-ZrO2 catalysts: Effects of surfactant/Cu-Zn-Zr molar ratio. J. CO2 Util. 2020, 41, 101215. [Google Scholar] [CrossRef]
  24. Liu, H.; Li, Y.; Yin, C.; Wu, Y.; Chai, Y.; Dong, D.; Li, X.; Liu, C. One-pot synthesis of ordered mesoporous NiMo-Al2O3 catalysts for dibenzothiophene hydrodesulfurization. Appl. Catal. B-Environ. 2016, 198, 493–507. [Google Scholar] [CrossRef]
  25. Ganiyu, S.; Alhooshani, K.; Ali, S. Single-pot synthesis of Ti-SBA-15-NiMo hydrodesulfurization catalysts: Role of calcination temperature on dispersion and activity. Appl. Catal. B-Environ. 2017, 203, 428–441. [Google Scholar] [CrossRef]
  26. Han, P.; Liu, T.; Ji, X.; Tang, S. Morphology-controlled synthesis of mesoporous silica with co-template of surfactant P123 and ionic liquid [Dmim]Cl. Chin. Chem. Lett. 2018, 29, 1305–1309. [Google Scholar] [CrossRef]
  27. Qin, T.; Lin, T.; Qi, X.; Wang, C.; Li, L.; Tang, Z.; Zhong, L.; Sun, Y. Tuning chemical environment and synergistic relay reaction to promote higher alcohols synthesis via syngas conversion. Appl. Catal. B-Environ. 2021, 285, 119840. [Google Scholar] [CrossRef]
  28. Huang, C.; Zhu, C.; Zhang, M.; Chen, J.; Fang, K. Design of efficient ZnO/ZrO2 modified CuCoAl catalysts for boosting higher alcohol synthesis in syngas conversion. Appl. Catal. B-Environ. 2022, 300, 120739. [Google Scholar] [CrossRef]
  29. Zhao, H.; Yu, R.; Ma, S.; Xu, K.; Chen, Y.; Jiang, K.; Fang, Y.; Zhu, C.; Liu, X.; Tang, Y.; et al. The role of Cu1-O3 species in single-atom Cu/ZrO2 catalyst for CO2 hydrogenation. Nat. Catal. 2022, 5, 818–831. [Google Scholar] [CrossRef]
  30. Wu, C.; Lin, L.; Liu, J.; Zhang, J.; Zhang, F.; Zhou, T.; Rui, N.; Yao, S.; Deng, Y.; Yang, F.; et al. Inverse ZrO2/Cu as a highly efficient methanol synthesis catalyst from CO2 hydrogenation. Nat. Commun. 2020, 11, 5767. [Google Scholar] [CrossRef]
  31. Tada, S.; Kayamori, S.; Honma, T.; Kamei, H.; Nariyuki, A.; Kon, K.; Toyao, T.; Shimizu, T.; Satokawa, S. Design of interfacial sites between Cu and amorphous ZrO2 dedicated to CO2-to-methanol hydrogenation. ACS Catal. 2018, 8, 7809–7819. [Google Scholar] [CrossRef]
  32. Sun, K.; Geng, S.; Yang, J.; Song, F.; Gu, Y.; Feng, H.; Tsubaki, N.; Zhang, Q.; Tan, Y. Potassium-mediated control of adsorbed intermediates on CuCoAl layered nanoplates for ethanol synthesis from syngas. Fuel 2024, 373, 132404. [Google Scholar] [CrossRef]
  33. Hong, Z.; Wang, J.; Gao, Z.; Huang, W. Tuning CuO crystallite size by different solvents for higher alcohols synthesis from syngas over CuZnAl catalyst. Int. J. Hydrogen Energy 2024, 56, 1032–1037. [Google Scholar] [CrossRef]
  34. Śliwa, M.; Samson, K. Influence of synthesis parameters on physicochemical properties of CuO/ZrO2 catalysts. Chem. Pap. 2019, 73, 2793–2802. [Google Scholar] [CrossRef]
  35. Zhan, H.; Li, F.; Gao, P.; Zhao, N.; Xiao, F.; Wei, W.; Zhong, L.; Sun, Y. Methanol synthesis from CO2 hydrogenation over La-M-Cu-Zn-O (M = Y, Ce, Mg, Zr) catalysts derived from perovskite-type precursors. J. Power Sources 2014, 251, 113–121. [Google Scholar] [CrossRef]
  36. Yu, Q.; Yao, X.; Zhang, H.; Gao, F.; Dong, L. Effect of ZrO2 addition method on the activity of Al2O3-supported CuO for NO reduction with CO: Impregnation vs. coprecipitation. Appl. Catal. A-Gen. 2012, 423–424, 42–51. [Google Scholar] [CrossRef]
  37. Yu, Q.; Liu, L.; Dong, L.; Li, D.; Liu, B.; Gao, F.; Sun, K.; Dong, L.; Chen, Y. Effects of Ce/Zr ratio on the reducibility, adsorption and catalytic activity of CuO/CexZr1-xO2/γ-Al2O3 catalysts for NO reduction by CO. Appl. Catal. B-Environ. 2010, 96, 350–360. [Google Scholar] [CrossRef]
  38. Gao, B.; Lim, T.; Subagio, D.; Lim, T. Zr-doped TiO2 for enhanced photocatalytic degradation of bisphenol A. Appl. Catal. A 2010, 375, 107–115. [Google Scholar] [CrossRef]
  39. Sato, A.; Volanti, D.; Meira, D.; Damyanova, S.; Longo, E.; Bueno, J. Effect of the ZrO2 phase on the structure and behavior of supported Cu catalysts for ethanol conversion. J. Catal. 2013, 307, 1–17. [Google Scholar] [CrossRef]
  40. Zhang, Z.; Jing, M.; Chen, H.; Okejiri, F.; Liu, J.; Leng, Y.; Liu, H.; Song, W.; Hou, Z.; Lu, X.; et al. Transfer hydrogenation of fatty acids on Cu/ZrO2: Demystifying the role of carrier structure and metal-support interface. ACS Catal. 2020, 10, 9098–9108. [Google Scholar] [CrossRef]
  41. Song, X.; Yang, C.; Li, X.; Wang, Z.; Pei, C.; Zhao, Z.; Gong, J. On the role of hydroxyl groups on Cu/Al2O3 in CO2 hydrogenation. ACS Catal. 2022, 12, 14162–14172. [Google Scholar] [CrossRef]
  42. Huang, H.; Wang, B.; Wang, Y.; Zhao, Y.; Wang, S.; Ma, X. Partial hydrogenation of dimethyl oxalate on Cu/SiO2 catalyst modified by sodium silicate. Catal. Today 2020, 358, 68–73. [Google Scholar] [CrossRef]
  43. Wang, Y.; Shen, Y.; Zhao, Y.; Lv, J.; Wang, S.; Ma, X. Insight into the balancing effect of active Cu species for hydrogenation of carbon-oxygen bonds. ACS Catal. 2015, 5, 6200–6208. [Google Scholar] [CrossRef]
  44. Sun, K.; Wu, Y.; Tan, M.; Wang, L.; Yang, G.; Zhang, M.; Zhang, W.; Tan, Y. Ethanol and higher alcohols synthesis from syngas over CuCoM (M = Fe, Cr, Ga and Al) nanoplates derived from hydrotalcite-like precursors. ChemCatChem 2019, 11, 2695–2706. [Google Scholar] [CrossRef]
  45. Yuan, X.; Chen, S.; Cheng, D.; Li, L.; Zhu, W.; Zhong, D.; Zhao, Z.; Li, J.; Wang, T.; Gong, J. Controllable Cu0-Cu+ sites for electrocatalytic reduction of carbon dioxide. Angew. Chem. Int. Ed. 2021, 28, 15344–15347. [Google Scholar] [CrossRef] [PubMed]
  46. Wang, J.; Li, G.; Li, Z.; Tang, C.; Feng, Z.; An, H.; Liu, H.; Liu, T.; Li, C. A highly selective and stable ZnO-ZrO2 solid solution catalyst for CO2 hydrogenation to methanol. Sci. Adv. 2017, 3, e1701290. [Google Scholar] [CrossRef]
  47. Kattel, S.; Yan, B.; Yang, Y.; Chen, J.; Liu, P. Optimizing binding energies of key intermediates for CO2 hydrogenation to methanol over oxide-supported copper. J. Am. Chem. Soc. 2016, 138, 12440–12450. [Google Scholar] [CrossRef]
  48. Ma, Z.; Yang, C.; Wei, W.; Li, W.; Sun, Y. Catalytic performance of copper supported on zirconia polymorphs for CO hydrogenation. J. Mol. Catal. A Chem. 2005, 231, 75–81. [Google Scholar] [CrossRef]
  49. He, D.; Ding, Y.; Luo, H.; Li, C. Effects of zirconia phase on the synthesis of higher alcohols over zirconia and modified zirconia. J. Mol. Catal. A Chem. 2004, 208, 267–271. [Google Scholar] [CrossRef]
  50. Wang, L.; Gao, X.; Bai, Y.; Tan, M.; Sun, K.; Zhang, T.; Wu, Y.; Pan, J.; Xie, H.; Tan, Y. The synergistic effect between ZnO and ZnCr2O4 on the catalytic performance for isobutanol synthesis from syngas. Fuel 2019, 253, 1570–1577. [Google Scholar] [CrossRef]
Figure 1. Catalytic activity of KCLZ-xP catalysts: (A) ROH distribution; (B) CO conversion, C2+OH/MeOH (derived from distribution of alcohols).
Figure 1. Catalytic activity of KCLZ-xP catalysts: (A) ROH distribution; (B) CO conversion, C2+OH/MeOH (derived from distribution of alcohols).
Catalysts 15 00431 g001
Figure 2. ASF plot of alcohols and the corresponding chain-growth probability (α): (A) KCLZ; (B) KCLZ-10P; (C) KCLZ-20P; (D) KCLZ-30P.
Figure 2. ASF plot of alcohols and the corresponding chain-growth probability (α): (A) KCLZ; (B) KCLZ-10P; (C) KCLZ-20P; (D) KCLZ-30P.
Catalysts 15 00431 g002
Figure 3. (A) N2 adsorption–desorption isotherms; (B) distributions of pore size over the KCLZ-xP catalysts.
Figure 3. (A) N2 adsorption–desorption isotherms; (B) distributions of pore size over the KCLZ-xP catalysts.
Catalysts 15 00431 g003
Figure 4. XRD patterns of the (A) calcined and (B) reduced KCLZ-xP catalysts.
Figure 4. XRD patterns of the (A) calcined and (B) reduced KCLZ-xP catalysts.
Catalysts 15 00431 g004
Figure 5. H2-TPR profiles of the calcined KCLZ-xP catalysts.
Figure 5. H2-TPR profiles of the calcined KCLZ-xP catalysts.
Catalysts 15 00431 g005
Figure 6. (A) CO, (B) CO2, and (C) NH3-TPD profiles of KCLZ-xP catalysts.
Figure 6. (A) CO, (B) CO2, and (C) NH3-TPD profiles of KCLZ-xP catalysts.
Catalysts 15 00431 g006
Figure 7. XPS of (A) Zr 3d, (B) O 1s, (C) Cu 2p, and (D) Cu Auger LMM spectra of reduced KCLZ-xP catalysts.
Figure 7. XPS of (A) Zr 3d, (B) O 1s, (C) Cu 2p, and (D) Cu Auger LMM spectra of reduced KCLZ-xP catalysts.
Catalysts 15 00431 g007
Figure 8. In situ DRIFTS spectra of CO adsorption in the high-frequency range over KCLZ-xP catalysts.
Figure 8. In situ DRIFTS spectra of CO adsorption in the high-frequency range over KCLZ-xP catalysts.
Catalysts 15 00431 g008
Figure 9. In situ DRIFTS spectra of CO adsorption in the low-frequency range over KCLZ-xP catalysts.
Figure 9. In situ DRIFTS spectra of CO adsorption in the low-frequency range over KCLZ-xP catalysts.
Catalysts 15 00431 g009
Table 1. Catalytic performance of different KCLZ-xP catalysts in gas-phase CO hydrogenation reaction 1.
Table 1. Catalytic performance of different KCLZ-xP catalysts in gas-phase CO hydrogenation reaction 1.
CatalystXCO/%Selectivity/%STYROH
g/(L·h)
STYgas
g/(L·h)
C2+OH/MeOHDistribution of Alcohols/(wt)%
ROHCO2CHxCH4C1C2C3C4i-C4C4+
KCLZ19.337.236.312.912.140770.5166.412.010.12.29.30
KCLZ-10P48.37.749.518.923.7304110.7856.120.713.53.06.80
KCLZ-20P58.37.64720.624.5385220.8952.925.513.03.34.40.9
KCLZ-30P63.16.545.624.623.0335280.9850.527.213.13.73.12.4
1 Reaction conditions: T = 350 °C, P = 5 MPa, GHSV = 3000 h−1, H2/CO = 2.5.
Table 2. Textural properties of the KCLZ-xP catalysts.
Table 2. Textural properties of the KCLZ-xP catalysts.
CatalystSurface Area SBET (m2/g)Pore Volume Vp (cm3/g)Pore Size Dp (nm)XCu+
(%)
KCLZ82.580.103.1563
KCLZ-10P88.530.113.6560
KCLZ-20P91.650.113.5757
KCLZ-30P72.750.103.7960
Table 3. Distribution of CO adsorption sites, base amount and acid amount over KCLZ-xP catalysts.
Table 3. Distribution of CO adsorption sites, base amount and acid amount over KCLZ-xP catalysts.
CatalystCO Adsorption (mmol/g)Basic Amount (mmol/g)Acid Amount (mmol/g)
Weak StrongTotal WeakMediumHighTotalWeakMediumHighTotal
KCLZ0.081
(70%)
0.035
(30%)
0.1160.1420.2880.0560.4860.0920.3410.090.553
KCLZ-10P0.056
(53%)
0.050
(47%)
0.1060.2730.1800.0390.4920.0100.2420.080.400
KCLZ-20P0.072
(56%)
0.057
(44%)
0.1290.1930.1910.0460.4300.0120.2370.0790.386
KCLZ-30P0.059
(56%)
0.047
(44%)
0.1060.1810.1930.0410.4150.0070.2410.0760.367
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Yang, J.; Jin, J.; Xue, D.; Zhi, L.; Wang, Z.; Sun, K. The Effect of Surfactant P123 on the KCuLaZrO2 Catalysts in the Direct Conversion of Syngas to Higher Alcohols. Catalysts 2025, 15, 431. https://doi.org/10.3390/catal15050431

AMA Style

Yang J, Jin J, Xue D, Zhi L, Wang Z, Sun K. The Effect of Surfactant P123 on the KCuLaZrO2 Catalysts in the Direct Conversion of Syngas to Higher Alcohols. Catalysts. 2025; 15(5):431. https://doi.org/10.3390/catal15050431

Chicago/Turabian Style

Yang, Jiaqian, Jiayu Jin, Duomei Xue, Lifei Zhi, Zhongqiang Wang, and Kai Sun. 2025. "The Effect of Surfactant P123 on the KCuLaZrO2 Catalysts in the Direct Conversion of Syngas to Higher Alcohols" Catalysts 15, no. 5: 431. https://doi.org/10.3390/catal15050431

APA Style

Yang, J., Jin, J., Xue, D., Zhi, L., Wang, Z., & Sun, K. (2025). The Effect of Surfactant P123 on the KCuLaZrO2 Catalysts in the Direct Conversion of Syngas to Higher Alcohols. Catalysts, 15(5), 431. https://doi.org/10.3390/catal15050431

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop