Next Article in Journal
The Properties of Black Locust Robinia pseudoacacia L. to Selectively Accumulate Chemical Elements from Soils of Ecologically Transformed Areas
Previous Article in Journal
Accuracy of a LiDAR-Based Individual Tree Detection and Attribute Measurement Algorithm Developed to Inform Forest Products Supply Chain and Resource Management
Previous Article in Special Issue
Particleboards from Recycled Pallets
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Editorial

Composites from Recycled and Modified Woods—Technology, Properties, Application

by
Ladislav Reinprecht
and
Ján Iždinský
*
Department of Wood Technology, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, 960 01 Zvolen, Slovakia
*
Author to whom correspondence should be addressed.
Forests 2022, 13(1), 6; https://doi.org/10.3390/f13010006
Submission received: 14 December 2021 / Accepted: 17 December 2021 / Published: 21 December 2021
The intention of efficient processing and use of less valuable wood species, bio-damaged logs, sawmill residues, cuttings, chips, sawdust, recycled wooden products, and other lignocellulosic raw materials in the production of wood composites is the focus of several scientific research institutes in the world. Wood composites are mostly produced for a particular application and, therefore, the raw materials, needed additives, production processes, as well as finishing and surface treatments are adapted for these purposes. Research into the optimization of material and technological parameters of the production of wood composites with special properties and applications is still ongoing.
Recycled woods obtained from old buildings, furniture, industrial products, etc., as well as from modified woods prepared by thermal, chemical, or biological processes, have the potential to be a base or complementary raw material for construction and decorative wood composites used mostly in buildings, furniture, and for transport. Typical construction composites are glued prisms and boards (e.g., glulam, blockboard), glued large-area boards from veneers (e.g., plywood, laminated veneer lumber (LVL)), or large-area boards from wood particles and fibers (e.g., particleboard (PB), oriented strand board (OSB), medium density fiberboard (MDF)). More of the large-area boards can obtain a better decorative function usable in furniture and building architecture after veneering, lamination, coating, plasma-treating or other surface-treating technologies.
Within this Special Issue, selected articles related primarily to wood composites prepared from recycled and modified woods are collected in focus on the type and properties of used raw materials, additives, technological processes, including finishing and surface treatments, with an impact on the resulting properties and service-life of wood composites under their different uses. Development of wood and cellulosic composites with specific compositions and properties, coming out from the knowledge of wood material science, timber engineering, physic, and other areas of research, is also to interest of this Special Issue.
The Special Issue comprises ten articles by authors from nine countries—eight from Europe (Bulgaria, France, Germany, Greece, Poland, Romania, Slovakia, and Ukraine) and one from Asia (Iran). These articles represent a wide range of aspects related to: (1) material composition, e.g., species, amount, fraction, and distribution of recycled and modified woods, type of glues, biocides, fire retardants, and other additives; (2) processing and finishing; (3) properties of wood composites for construction and decorative use.
Authors in articles reported about: (a) new sources of the raw material for PBs, such as recycled wood waste generated in wood processing from faulty PBs bonded with urea-formaldehyde (UF) resin or taken from old furniture and other end-of-life wood products, including spruce pallets and thermally modified wood, taking into account the environmental and economic aspects of wood recyclates and obtaining the knowledge that the moisture, strength, and biological properties of PBs can be specifically improved, e.g., the resistance of PBs to swelling in water and to fungal decay increased at using particles from faulty PBs or thermowood cuttings [1,2,3]; (b) enhancing the use of heterogeneous wood veneers in the manufacturing of maximized-performance LVL panels by veneer grading and optimized positioning, as well as the LVL material mechanical property modeling, with a proposed optimization strategy of LVL manufacturing from variable-quality veneers in terms of their optimal stiffness or strength [4,5]; (c) the penetration process of liquids with different polarities and molecular weights through the surface of MDF and PB panels, when the most polar water molecules created strong and stable bonds with the cellulose of wood composites, and therefore, the penetration of water in their structure was the slowest [6]; (d) the effect of birch and black alder veneers’ densification temperature and increased density on the mechanical plywood properties made from alternate layers of densified and non-densified veneers, e.g., the increase in the veneer’s densification temperature from 150 to 210 °C resulted in a gradual decrease in the plywood’s bending strength [7]; (e) the ecofriendly PBs and MDF composites produced from industrial waste fibers and magnesium lignosulfonate adhesive, at which such prepared composites had good mechanical properties but with worsened moisture properties [8]; (f) a CO2 laser modification of beech and spruce wood surfaces before or after their coating with polyvinyl acetate (PVAc) or polyurethane (PUR) polymers, where the laser beams degraded and carbonized the wood adherent or the synthetic polymer layer and thus worsened the adhesion strength between wood and coating, while the mold resistance of laser-modified surfaces specifically increased [9]; (g) new fire retardants for cellulose and cellulose-modified materials, e.g., the expandable graphite, could be a very effective intumescent and environmentally friendly fire retardant [10].

Acknowledgments

We would like to thank MDPI Forests, as well as the Slovak Research and Development Agency under contract no. APVV-17-0583, for support of this editorial article.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Iždinský, J.; Vidholdová, Z.; Reinprecht, L. Particleboards from Recycled Wood. Forests 2020, 11, 1166. [Google Scholar] [CrossRef]
  2. Iždinský, J.; Vidholdová, Z.; Reinprecht, L. Particleboards from Recycled Thermally Modified Wood. Forests 2021, 12, 1462. [Google Scholar] [CrossRef]
  3. Iždinský, J.; Reinprecht, L.; Vidholdová, Z. Particleboards from Recycled Pallets. Forests 2021, 12, 1597. [Google Scholar] [CrossRef]
  4. Duriot, R.; Pot, G.; Girardon, S.; Roux, B.; Marcon, B.; Viguier, J.; Denaud, L. New Perspectives for LVL Manufacturing from Wood of Heterogeneous Quality—Part. 1: Veneer Mechanical Grading Based on Online Local Wood Fiber Orientation Measurement. Forests 2021, 12, 1264. [Google Scholar] [CrossRef]
  5. Duriot, R.; Pot, G.; Girardon, S.; Denaud, L. New Perspectives for LVL Manufacturing from Wood of Heterogeneous Quality—Part 2: Modeling and Manufacturing of Variable Stiffness Beams. Forests 2021, 12, 1275. [Google Scholar] [CrossRef]
  6. Taghiyari, H.R.; Majidi, R.; Arsalan, M.G.; Moradiyan, A.; Militz, H.; Ntalos, G.; Papadopoulos, A.N. Penetration of Different Liquids in Wood-Based Composites: The Effect of Adsorption Energy. Forests 2021, 12, 63. [Google Scholar] [CrossRef]
  7. Salca, E.-A.; Bekhta, P.; Seblii, Y. The Effect of Veneer Densification Temperature and Wood Species on the Plywood Properties Made from Alternate Layers of Densified and Non-Densified Veneers. Forests 2020, 11, 700. [Google Scholar] [CrossRef]
  8. Antov, P.; Mantanis, G.I.; Savov, V. Development of Wood Composites from Recycled Fibres Bonded with Magnesium Lignosulfonate. Forests 2020, 11, 613. [Google Scholar] [CrossRef]
  9. Reinprecht, L.; Vidholdová, Z. The Impact of a CO2 Laser on the Adhesion and Mold Resistance of a Synthetic Polymer Layer on a Wood Surface. Forests 2021, 12, 242. [Google Scholar] [CrossRef]
  10. Mazela, B.; Batista, A.; Grześkowiak, W. Expandable Graphite as a Fire Retardant for Cellulosic Materials—A Review. Forests 2020, 11, 755. [Google Scholar] [CrossRef]
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Reinprecht, L.; Iždinský, J. Composites from Recycled and Modified Woods—Technology, Properties, Application. Forests 2022, 13, 6. https://doi.org/10.3390/f13010006

AMA Style

Reinprecht L, Iždinský J. Composites from Recycled and Modified Woods—Technology, Properties, Application. Forests. 2022; 13(1):6. https://doi.org/10.3390/f13010006

Chicago/Turabian Style

Reinprecht, Ladislav, and Ján Iždinský. 2022. "Composites from Recycled and Modified Woods—Technology, Properties, Application" Forests 13, no. 1: 6. https://doi.org/10.3390/f13010006

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop