Next Article in Journal
New Zr-Ti-Nb Alloy for Medical Application: Development, Chemical and Mechanical Properties, and Biocompatibility
Next Article in Special Issue
Ozonized Gel Against Four Candida Species: A Pilot Study and Clinical Perspectives
Previous Article in Journal
Effect of Single-Walled Carbon Nanotubes on Strength Properties of Cement Composites
Previous Article in Special Issue
In Vitro Re-Hardening of Bleached Enamel Using Mineralizing Pastes: Toward Preventing Bacterial Colonization
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Materials
Volume 13
Issue 6
10.3390/ma13061308
materials-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

New Resin-Based Bulk-Fill Composites: in vitro Evaluation of Micro-Hardness and Depth of Cure as Infection Risk Indexes

by
Marco Colombo
1,
Simone Gallo
1,*,
Claudio Poggio
1,*,
Vittorio Ricaldone
1,
Carla Renata Arciola
2,3,* and
Andrea Scribante
1
1
Department of Clinical, Surgical, Diagnostic and Paediatric Sciences – Section of Dentistry, University of Pavia, Piazzale Golgi 2, 27100 Pavia, Italy
2
IRCCS Istituto Ortopedico Rizzoli, Laboratorio di Patologia delle Infezioni Associate all’Impianto, via di Barbiano 1/10, 40136 Bologna, Italy
3
Department of Experimental, Diagnostic and Specially Medicine, University of Bologna, via San Giacomo 14, 40126 Bologna, Italy
*
Authors to whom correspondence should be addressed.
Materials 2020, 13(6), 1308; https://doi.org/10.3390/ma13061308
Submission received: 29 January 2020 / Revised: 19 February 2020 / Accepted: 11 March 2020 / Published: 13 March 2020
(This article belongs to the Special Issue Anti-Infective Materials)
Browse Figures
Versions Notes

Abstract

:
The current in vitro study evaluated the Vickers hardness number (VHN) and hardness ratio of four bulk-fill composites (VisCalor bulk; Admira Fusion x-tra; x-tra fil; and GrandioSO x-tra-Voco, Cuxhaven, Germany) to assess the risk of bacterial colonization in comparison with standard composite materials. Thirty samples were prepared for each group. The VHN of both the external (top) and internal surface (bottom) was determined with a micro-hardness tester (200 g load for 15 s), and the hardness ratio was also calculated for each sample. Subsequently, storage in an acidic soft drink (Coca-Cola, Coca-Cola Company, Milano, Italy) was performed; for each group, 10 samples were stored for 1 day, while another 10 were stored for 7 days and the remaining 10 were kept in water as controls. A significant reduction in VHN was shown for all the groups when comparing the external versus internal side (P < 0.05), although the hardness ratio was greater than 0.80, resulting in an adequate polymerization. Regarding the acid storage, all the groups showed a significant decrease of VHN when compared with the controls, both after 1 day (P < 0.05) and after 7 days (P < 0.001). All the products showed adequate depth of cure without further risk of bacterial colonization. However, acid exposure negatively affected micro-hardness values, which might promote subsequent colonization.

1. Introduction

Resin-based composites (RBCs) are nowadays the most used materials for the direct restoration of teeth, mainly due to their aesthetic properties, which are extremely appreciated when compared to those of other materials historically used in dentistry [1]. Traditionally, RBCs require an incremental apposition of 2 mm-layers, both to allow the curing light to penetrate the material and to contrast the shrinkage that takes place during polymerization [2]. Because of the multiple stratifications necessary, this technique may be quite time-consuming, especially when big cavities of the tooth must be filled. Therefore, in recent years, manufacturers have tried to develop new products requiring single-layer stratification, thus reducing the operative steps. Resin-based “bulk-fill” composites (BFCs) have been introduced with this purpose, and according to manufacturers, can be used in a single step to fill cavities of a 4 mm depth or greater [3]. However, when choosing composite resins, clinicians should consider the risks of secondary decay and cytotoxicity that are still associated with them [4,5].
The first objection to BFCs concerns their effective depth of cure, considering the gradual decrease in the degree of conversion from the external surface exposed to the curing light to the internal one [6], with scattering and absorption being the major factors related to light attenuation [7]. A low depth of cure has been showed to compromise the color stability, but above all, the mechanical and biological properties of the restorations [7,8]. As with the mechanical ones, in fact, a degree of conversion below a minimum threshold of 55% is considered insufficient, thus causing less resistance to wear [9]. Instead, regarding the biological properties, an incomplete curing of the composite might be responsible for bacterial colonization. In fact, the release of monomers (such as EGDMA and TEDGMA) from incompletely cured composites has been reported to promote the proliferation of cariogenic bacteria [10], as well as being associated with the cytotoxicity of gingival and pulp fibroblast cells [11]. Considering that residual monomers can be released even in well-polymerized RBCs [12], a major amount might elute from BFCs.
In the present in vitro study, we aimed to indirectly evaluate the depth of cure of four bulk-fill composites, assessing the Vickers hardness number (VHN) and hardness ratio. These parameters have been considered, since a significant correlation between increasing hardness and depth of cure is generally regarded [8,13]. Subsequently, the change in the surface micro-hardness of the tested materials following two alternative acid storages of 1 and 7 days respectively, was compared with the control samples that were stored in water.
The first null hypothesis of this study is that there is no significant difference in the hardness ratio of the new materials if compared with well-polymerized traditional RBCs, thus achieving a value of at least 0.80, as considered in literature [12,14]. Furthermore, the second null hypothesis is that no significant difference in micro-hardness values occurs after the two respective acid storages, compared to the controls.

2. Materials and Methods

Four composite resins (Voco, Cuxhaven, Germany) were selected for the present study: VisCalor Bulk (Group 1); Admira Fusion x-tra (Group 2); x-tra fil (Group 3); and GrandioSO x-tra (Group 4). The specifications of the materials and their acronym codes are listed in Table 1. For each product, the A2 Vita shade was chosen to reduce the effects of colorants on light-curing.
Thirty samples for each group were prepared by inserting the respective BFC into a stainless-steel mold (Ø 7 mm, h 4 mm) placed on a dark opaque paper background, with a polyester matrix strip interposed. This arrangement was chosen to obtain a smooth surface under the composite, but also to avoid light reflection from the bottom, thus minimizing the artificial hardening of this area [15]. Considering its termoviscous behaviour, VisCalor Bulk was preheated before the application with the preheating device (Caps Warmer, Voco, Cuxhaven, Germany) at 68 °C for 15 min, in accordance with the operating instructions.
Each mold was slightly overfilled, and a second polyester matrix strip (Mylar strip, Henry Schein, Melville, NY, USA) was placed on the top to prevent oxygen from interfering with the polymerization of the most superficial layer of the composite [16]; in order to extrude the excess composite resin and obtain a flat surface, a glass slide was pressed against the upper polyester film, and removed before curing [17].
Each sample was light-cured with the LED unit Celalux 2 (Voco, Cuxhaven, Germany), and was removed from the mold without undergoing polishing. Before every use, the cordless curing unit was maintained at full charge, and irradiance was checked with a radiometer (SDS Kerr, Orange, CA, USA). The distal end of the light guide was placed perpendicular to the surface of the matrix strip, and positioned concentrically with the mold, before starting the light-curing of the samples, which only took place on their external (top) side [18]. Exclusively one light polymerization mode was used (standard mode), with an output irradiance of 1000 mW/cm2 for 20 s, which are considered the minimum parameters to polymerize 4 mm increments of bulk-fill composites [19].
In order to simulate the physiological oral conditions, the samples were stored for 48 h in complete darkness, at 37 °C and 100% humidity, before proceeding with the assessment of the Vickers hardness number (VHN) [14]. This period has been awaited, as the polymerization of composite resins continues at a slow rate even after curing [8].
After removing the Mylar strip, the VHN of the upper and lower surface of each sample was determined with a micro-hardness tester (durometer Isoscan HV2, LTF Spa, Antegnate, Bergamo, Italy) equipped with a Vickers diamond indenter to apply a 200 g load with a 15 s dwell time [20]. Three indentations were equally placed over a circle, with each being no closer than 0.5 mm to the adjacent indentation (UNI EN ISO 6507) [21]. A 40× magnification built-in scale microscope was used to measure the two diagonals of each indentation. The VHN was calculated in kgp/mm2 using the following equation: HV = 1.854 P/d2, where P is the load in kgf and d is the average length in mm of the diagonals. For a given specimen, a single hardness value was reported for each of the two surfaces, resulting from the mean of the three respective hardness values assessed. Furthermore, the hardness ratio of the specimens was calculated using the formula: hardness ratio = mean VHN of bottom surface / mean VHN of top surface.
After the procedure described, the thirty samples of each group were divided into three subgroups (n = 10 per subgroup), as showed in Figure 1: each first subgroup (1A–4A) was kept in water during this experimental phase and was considered as control, while the other two subgroups underwent an acid storage in a soft drink (Coca-Cola, Coca-Cola Company, Milano, Italy) conserved at room temperature (18 ± 1 °C). In particular, the former (subgroups 1B–4B) were left inside for 1 day, while the latter (subgroups 1C–4C) were left for 7 days, with a daily renew of the soft drink.
At the end of the acid storage, the subgroups underwent hardness testing performed as previously described, but in this case, considering only the upper surface of the samples, which represents the portion of the material directly exposed to an erosive action in the oral cavity.
Data were submitted to statistical analysis using computer software (R version 3.1.3, R Development Core Team, R Foundation for Statistical Computing, Wien, Austria). Descriptive statistics, including the mean, standard error of mean, median, minimum and maximum values, were calculated for all groups. The normality of distributions was assessed with a Kolmogorov–Smirnov test. A multi-factor analysis of variance (ANOVA) and Tukey tests were applied to show differences among groups. Significance for all statistical tests was predetermined at P < 0.05. A linear regression model for Vickers hardness was performed, adding as a covariate the immersion time in the acidic drink.

3. Results

Descriptive statistics of the tested materials’ micro-hardness after light curing are shown in Table 2. The acronym codes are reported as given in Table 1.
Considering the four bulk-fill composites (VIS, FUS, XTF and GRA) and comparing the external (top, A) versus the internal side (bottom, B) of the samples, a significant difference in the mean percentage reduction of VHN was shown for all the respective groups tested (P < 0.05) (Figure 2), with 18.14% for group 1 (VIS), 14.40% for group 2 (FUS), 4.79% for group 3 (XTF) and 8.22% for group 4 (GRA) (Table 3), in accordance with their hardness ratio (0.82, 0.86, 0.95 and 0.92, respectively), as shown in Table 4. Despite this reduction between the values of the top and bottom sides, the hardness ratio was higher than 0.80 for all the groups.
Descriptive statistics of the micro-hardness after acid storage are shown in Table 5. When evaluating the acidic drink storage, all the tested products showed a significant decrease of VHN, both after the 1-day storage (P < 0.05) and the 7-day storage (P < 0.001) in Coca-Cola, compared to the control subgroups stored in water (Figure 3). Meanwhile, solely for group 1 (VIS) and group 2 (FUS), the mean percentage micro-hardness losses after the first day of immersion (T0–T1), which were 7.30% and 7.83% respectively, were higher than those which took place during the following six days (T1–T2), which were 6.58% and 5.97% respectively, although these latter values are not significantly different if compared to the former. On the contrary, in accordance with other studies assessing a major micro-hardness loss of restorative dental materials during the first seven days of acid exposure [22], an opposite trend has been reported for groups 3 and 4 (Table 6)—even in this case, however, no significant difference was shown comparing the micro-hardness losses at the two times considered. Anyway, the mean percentage reduction of VHN at the end of the 1-day acid storage only appeared to be significantly lower for group 3 if compared with the other groups at the same time, while it was significantly lower for both groups 3 and 4 considering the 7-day acid storage.
The linear regression model (Table 7) shows that the Vickers hardness was significantly affected by the immersion time in an acidic drink (P < 0.0001).

4. Discussion

Since the introduction of light-cured resin composites, several studies have showed that their degree of light-curing depends on both intrinsic and extrinsic factors, with the former including the photoinitiator system, optical properties, filler, type and amount of monomer, while the latter includes the light spectrum, light irradiance, irradiation time and mode, temperature and light guide tip positioning [23]. Adequate polymerization is considered a crucial factor for the success of the restoration, since an insufficient curing degree is responsible for water absorption, decreasing wear resistance and strength, and the elution of uncured monomer with a toxic effect [24,25].
Studies assessing the depth of cure are essential, even in the lower surfaces of the materials, as the cure of composite restorations can only be evaluated by clinicians in the upper surface that are directly exposed to the curing light [26,27]. Both direct and indirect methods have been proposed to evaluate the depth of cure. Among the latter, micro-hardness correlates well with the degree of conversion of resin composites [28,29], although an absolute hardness number cannot be used to directly compare different resins [14]. Conversely, other methods such as optical microscopy and scraping [30] have been shown to overestimate the depth of cure [6,31].
Traditional resin-based composites (RBCs) are used in dentistry with a 2 mm-incremental technique, which has been shown to be effective in ensuring well-polymerized layers [32]. However, many defects have been discussed, such as the failure of bonding between the layers, the presence of free spaces and a possible contamination among them [8]. Anyway, one of the most relevant disadvantages related to this technique is the difficulty of restoring small cavities, as well as the lengthy application time [33]. In order to avoid these factors, bulk-fill resin composites have been proposed in recent years with the potentiality of being cured with thickness of 4 mm or even more, according to manufacturers. These materials are characterized by particular properties which allow the polymerization of layers of such a depth.
One of the purposes of this study was to verify the effective depth of cure of four bulk-fill resin composites, in order to estimate a possible risk of bacterial colonization and secondary decay associated with the uncured monomer elution from these materials; in fact, an inverse correlation between the depth of cure and monomer elution occurs [8].
The micro-hardness value of the external side of the tested materials was significantly different between the groups, and was reported, in increasing order, for Admira Fusion x-tra, GrandioSO x-tra, VisCalor Bulk and x-tra fil. Considering the internal side, the values were reported in the same order, but with no significant difference between VisCalor Bulk and GrandioSO x-tra.
Since the only VHN cannot be considered as an index of the depth of cure, this was assessed in this study through the hardness ratio. All groups have showed a value greater than 0.80, which is the minimum to consider traditional RBCs as adequately cured [12,14].
As regards VisCalor Bulk and Admira Fusion x-tra, the hardness ratios were 0.82 and 0.86, respectively. This shows that, despite the latter material being characterized by lower micro-hardness numbers, the values of its two opposite surfaces are more similar between them than if compared to those of VisCalor Bulk, resulting in a hardness ratio nearer to 1. This can be explained considering the intrinsic factors of the material, such as a combination of the conventional photoinitiator system with one that is more sensitive [16], as well as a higher translucency, allowing a major amount of curing light to penetrate and polymerize the material homogeneously [34]. In particular, the reduction of the refractive index difference existing between the base resin and filler is related to an improvement of the degree of conversion and depth of cure [35,36].
Incidentally, the highest hardness ratios reported in this study were for GrandioSO x-tra and x-tra fil, respectively, with 0.92 and 0.95. For the same reasons previously reported for Admira Fusion x-tra, GrandioSO x-tra shows a similar hardness ratio to x-tra fil, despite its lower micro-hardness values.
According to these results, the first null hypothesis of this study has been accepted, since all the tested bulk-fill composites—particularly x-tra fil and GrandioSO x-tra—guarantee an adequate degree of conversion when polymerized in layers of 4 mm, despite only a polymerization mode being used in the present study.
We can assert that these materials do not present a greater risk compared with traditional RBCs, with regards to bacterial colonization and the subsequent risk of secondary infection of the tooth. Moreover, in accordance with this, other studies reported that despite a major amount of cuspal deflection [37], bulk-fill composites seem to show no negative influence on marginal integrity [38].
Considering that a low pH due to acidic drinks and foods influences the material’s mechanical and chemical properties [39], the second purpose of the study was to verify the micro-hardness change of the external side of the materials after two different acid storages, of 1 day and 7 days, respectively, carried out in Coca-Cola (pH = 2.52) at room temperature (18 ± 1 °C). The exposure to the acid drink was continuous, in order to simulate long-term exposure to carbonated beverages in the oral cavity. In fact, immersion in Coca-Cola for only one day is analogous to its consumption for a month, considering the time it remains in the mouth while drinking [40].
In both storages, the micro-hardness of all tested materials was negatively affected. After both the 1-day and the 7-day acid storage, one of the highest mean percentage losses in micro-hardness was reported for VisCalor Bulk (of 7.30% and 13.42%, respectively). Despite its greater mean percentage reductions, however, this material reported a final micro-hardness value even higher than GrandioSO x-tra not exposed to the acidic drink, which is due to the higher initial micro-hardness value of the former material.
Instead, regarding Admira Fusion x-tra, even though the mean percentage reductions were similar to those of VisCalor Bulk, its micro-hardness values were the lowest after the two acid storages among all the tested products, due to its low initial microhardness value. Finally, x-tra fil was the bulk-fill composite which showed the highest micro-hardness value before being exposed to the acid, and considering it also had the lowest mean percentage reductions after both acid storages, it is the material least affected by the acidic drink in the present study.
In conclusion, the second null hypothesis of this study has been rejected. As reported by other authors, the degradation of the composites’ polymer network, as well as the falling out of the filler due to the continuous action of acidic beverages, are responsible for the composites’ loss of micro-hardness [41,42,43,44]. Despite Coca-Cola being the soft drink most commonly used to study the properties’ change of restorative materials, other substances like food stimulating solvents [45] should also be tested.
Based on the importance of enamel and bone hardness, since bacteria takes advantage of micro-alterations [46], a decrease of the material’s hardness following the erosive action of acids might also be responsible for bacterial colonization. The biofilm accumulated over the restoration produces acidic substances, which further cause a surface degradation with the subsequent softening and roughening of the material’s surface [46,47]. Finally, a greater penetration of microorganisms through the fissure interposed between the restoration and the enamel may occur, resulting in the re-infection of the tooth (secondary caries) [48,49,50]. However, other factors influence this process under in vivo conditions, such as the buffering capacity of saliva, which decreases the erosive action of acids, as well as having a remineralizing effect on the tooth [51].
Moreover, the potential benefit of a better understanding of tooth decay by acidic drinks and/or acidifying bacteria that colonize and erode the teeth could extend to the knowledge of the pathogenesis of bone diseases in both the dental/periodontal and orthopedic fields. Indeed, bacteria-induced acidosis and metabolic acidosis can impinge on bone healing, negatively affecting the osteoblast-osteoclast equilibrium, collagen synthesis and bone matrix mineralization. Bone remodeling is not only controlled by cells, but also by the extracellular milieu, where calcium phosphate salts precipitate in a pH-dependent manner. Bone infection acidifies the milieu and promotes the formation/activation of osteoclasts, thus allowing hypothesizing that local pH changes may play a significant role in the pathogenesis of bone resorption and severely destructive osteomyelitis.
The limitations of the current report are related to the fact that the present study was completely conducted in vitro; in fact, laboratory experiments cannot duplicate intraoral conditions. Additionally, only bulk fill composites have been tested in the current report, and no traditional materials have been considered. Finally, a single acidic solution has been tested.
Further prospective in vivo studies should be performed to confirm the efficacy of bulk-fill resin composites in avoiding a major risk of secondary decay, related to the release of uncured monomers, but also to the loss of micro-hardness following exposure to acid.

5. Conclusions

Despite the limitations of this in vitro study, all the tested resin-based bulk-fill composites have shown an adequate depth of cure, which does not prefigure a major risk of secondary decay in comparison to traditional composites. As also reported for the latter, micro-hardness values appeared significantly decreased after both 1-day and 7-day acid storage, which may facilitate the subsequent bacterial colonization of the restorations, with a risk of secondary decay.

Author Contributions

Conceptualization, M.C., A.S. and S.G.; Methodology, S.G.; Software, A.S.; Validation, C.P. and C.R.A.; Formal Analysis, A.S.; Investigation, V.R. and S.G.; Resources, S.G. and V.R.; Data Curation, A.S.; Writing—Original Draft Preparation, S.G.; Conceptualization of the role of demineralization in infection, C.R.A.; Writing—Review and Editing, A.S. and C.R.A.; Visualization, A.S. and M.C.; Supervision, C.P. and C.R.A.; Project Administration, C.P. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Acknowledgments

We are grateful to VOCO for providing the bulk-fill composites tested, and to LTF SpA (Antegnate, Bergamo) for surface micro-hardness tests.

Conflicts of Interest

The authors of this study have no conflict of interest to disclose.

References

  1. Devoto, W.; Saracinelli, M.; Manauta, J. Composite in everyday practice: How to choose the right material and simplify application techniques in the anterior teeth. Eur. J. Esthet. Dent. 2010, 5, 102–124. [Google Scholar] [PubMed]
  2. Hamlin, N.J.; Bailey, C.; Motyka, N.C.; Vandewalle, K.S. Effect of tooth-structure thickness on light attenuation and depth of cure. Oper. Dent. 2016, 41, 200–207. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  3. Reis, A.F.; Vestphal, M.; Amaral, R.C.D.; Rodrigues, J.A.; Roulet, J.F.; Roscoe, M.G. Efficiency of polymerization of bulk-fill composite resins: A systematic review. Braz. Oral Res. 2017, 31, e59. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  4. Krifka, S.; Spagnuolo, G.; Schmalz, G.; Schweikl, H. A review of adaptive mechanisms in cell responses towards oxidative stress caused by dental resin monomers. Biomaterials 2013, 34, 4555–4563. [Google Scholar] [CrossRef] [PubMed]
  5. Nedeljkovic, I.; Teughels, W.; De Munck, J.; Van Meerbeek, B.; Van Landuyt, K.L. Is secondary caries with composites a material-based problem? Dent. Mater. 2015, 31, e247–e277. [Google Scholar] [CrossRef] [PubMed]
  6. Flury, S.; Hayoz, S.; Peutzfeldt, A.; Hüsler, J.; Lussi, A. Depth of cure of resin composites: Is the ISO 4049 method suitable for bulk fill materials? Dent. Mater. 2012, 28, 521–528. [Google Scholar] [CrossRef]
  7. Musanje, L.; Darvell, B.W. Curing-light attenuation in filled-resin restorative materials. Dent. Mater. 2006, 22, 804–817. [Google Scholar] [CrossRef]
  8. Alrahlah, A.; Silikas, N.; Watts, D.C. Post-cure depth of cure of bulk fill dental resin composites. Dent. Mater. 2014, 30, 149–154. [Google Scholar] [CrossRef]
  9. Silikas, N.; Eliades, G.; Watts, D.C. Light intensity effects on resin-composite degree of conversion and shrinkage strain. Dent. Mater. 2000, 16, 292–296. [Google Scholar] [CrossRef]
  10. Gupta, S.K.; Saxena, P.; Pant, V.A.; Pant, A.B. Release and toxicity of dental resin composite. Toxicol. Int. 2012, 19, 225–234. [Google Scholar]
  11. Cebe, M.A.; Cebe, F.; Cengiz, M.F.; Cetin, A.R.; Arpag, O.F.; Ozturk, B. Elution of monomer from different bulk fill dental composite resins. Dent. Mater. 2015, 31, e141–e149. [Google Scholar] [CrossRef]
  12. Moore, B.K.; Platt, J.A.; Borges, G.; Chu, T.M.; Katsilieri, I. Depth of cure of dental resin composites: ISO 4049 depth and microhardness of types of materials and shades. Oper. Dent. 2008, 33, 408–412. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  13. Aguiar, F.H.; Braceiro, A.; Lima, D.A.; Ambrosano, G.M.; Lovadino, J.R. Effect of light curing modes and light curing time on the microhardness of a hybrid composite resin. J. Contemp. Dent. Pract. 2007, 8, 1–8. [Google Scholar] [PubMed]
  14. Bouschlicher, M.R.; Rueggeberg, F.A.; Wilson, B.M. Correlation of bottom-to-top surface microhardness and conversion ratios for a variety of resin composite compositions. Oper. Dent. 2004, 29, 698–704. [Google Scholar] [PubMed]
  15. Rode, K.M.; Kawano, Y.; Turbino, M.L. Evaluation of curing light distance on resin composite microhardness and polymerization. Oper. Dent. 2007, 32, 571–578. [Google Scholar] [CrossRef]
  16. Zorzin, J.; Maier, E.; Harre, S.; Fey, T.; Belli, R.; Lohbauer, U.; Petschelt, A.; Taschner, M. Bulk-fill resin composites: Polymerization properties and extended light curing. Dent. Mater. 2015, 31, 293–301. [Google Scholar] [CrossRef]
  17. Beltrami, R.; Chiesa, M.; Scribante, A.; Allegretti, J.; Poggio, C. Comparison of shear bond strength of universal adhesives on etched and nonetched enamel. J. Appl. Biomater. Funct. Mater. 2016, 14, e78–e83. [Google Scholar] [CrossRef] [Green Version]
  18. Poggio, C.; Lombardini, M.; Gaviati, S.; Chiesa, M. Evaluation of Vickers hardness and depth of cure of six composite resins photo-activated with different polymerization modes. J. Conserv. Dent. 2012, 15, 237. [Google Scholar] [CrossRef]
  19. Lima, R.B.W.; Troconis, C.C.M.; Moreno, M.B.P.; Murillo-Gómez, F.; De Goes, M.F. Depth of cure of bulk fill resin composites: A systematic review. J. Esthet. Restor. Dent. 2018, 30, 492–501. [Google Scholar] [CrossRef]
  20. Kattan, H.; Chatzistavrou, X.; Boynton, J.; Dennison, J.; Yaman, P.; Papagerakis, P. Physical Properties of an Ag-Doped Bioactive Flowable Composite Resin. Materials 2015, 8, 4668–4678. [Google Scholar] [CrossRef] [Green Version]
  21. Colombo, M.; Poggio, C.; Lasagna, A.; Chiesa, M.; Scribante, A. Vickers micro-hardness of new restorative CAD/CAM dental materials: Evaluation and comparison after exposure to acidic drink. Materials 2019, 12, 1246. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  22. Hashemikamangar, S.S.; Pourhashemi, S.J.; Talebi, M.; Kiomarsi, N.; Kharazifard, M.J. Effect of organic acids in dental biofilm on microhardness of a silorane-based composite. Restor. Dent. Endod. 2015, 40, 188–194. [Google Scholar] [CrossRef] [PubMed]
  23. Leprince, J.G.; Palin, W.M.; Hadis, M.A.; Devaux, J.; Leloup, G. Progress in dimethacrylate-based dental composite technology and curing efficiency. Dent. Mater. 2013, 29, 139–156. [Google Scholar] [CrossRef] [PubMed]
  24. Da Silva, E.M.; Poskus, L.T.; Guimarães, J.G.; de Araújo Lima Barcellos, A.; Fellows, C.E. Influence of light polymerization modes on degree of conversion and crosslink density of dental composites. J. Mater. Sci. Mater. Med. 2008, 19, 1027–1032. [Google Scholar] [CrossRef] [PubMed]
  25. Moon, H.J.; Lee, Y.K.; Lim, B.S.; Kim, C.W. Effects of various light curing methods on the leachability of uncured substances and hardness of a composite. J. Oral Rehabil. 2004, 31, 258–264. [Google Scholar] [CrossRef] [PubMed]
  26. Koupis, N.S.; Martens, L.C.; Verbeeck, R.M. Relative curing degree of polyacid-modified and conventional resin composites determined by surface Knoop hardness. Dent. Mater. 2006, 22, 1045–1050. [Google Scholar] [CrossRef] [PubMed]
  27. Yap, A.U.; Soh, M.S.; Siow, K.S. Effectiveness of composite cure with pulse activation and soft-start polymerization. Oper. Dent. 2002, 27, 44–49. [Google Scholar]
  28. Ferracane, J.L. Correlation between hardness and degree of conversion during the setting reaction of unfilled dental restorative resins. Dent. Mater. 1985, 1, 11–14. [Google Scholar] [CrossRef]
  29. Rueggeberg, F.A.; Craig, R.G. Correlation of parameters used to estimate monomer conversion in a light-cured composite. J. Dent. Res. 1988, 67, 932–937. [Google Scholar] [CrossRef]
  30. ISO 4049:1988 (2.) Dentistry—Resin-Based Filling Materials; International Organization for Standardization: Geneva, Switzerland, 1988.
  31. DeWald, J.P.; Ferracane, J.L. A comparison of four modes of evaluating depth of cure of light-activated composites. J. Dent. Res. 1987, 66, 727–730. [Google Scholar] [CrossRef]
  32. Lucey, S.; Lynch, C.D.; Ray, N.J.; Burke, F.M.; Hannigan, A. Effect of pre-heating on the viscosity and microhardness of a resin composite. J. Oral Rehabil. 2010, 37, 278–282. [Google Scholar] [CrossRef]
  33. Abbas, G.; Fleming, G.J.P.; Harrington, E.; Shortall, A.C.C.; Burke, F.J.T. Cuspal Movement. Microleakage in premolar teeth restoredwith a packable composite cured in bulk or in increments. J. Dent. 2003, 31, 437–444. [Google Scholar] [CrossRef]
  34. Bucuta, S.; Ilie, N. Light transmittance and micro-mechanical properties of bulk fill vs. conventional resin based composites. Clin. Oral Investig. 2014, 18, 1991–2000. [Google Scholar] [CrossRef] [PubMed]
  35. Fujita, K.; Nishiyama, N.; Nemoto, K.; Okada, T.; Ikemi, T. Effect of base monomer’s refractive index on curing depth and polymerization conversion of photo-cured resin composites. Dent. Mater. J. 2005, 24, 403–408. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  36. Shortall, A.C.; Palin, W.M.; Burtscher, P. Refractive index mismatch and monomer reactivity influence composite curing depth. J. Dent. Res. 2008, 87, 84–88. [Google Scholar] [CrossRef] [PubMed]
  37. Park, J.; Chang, J.; Ferracane, J.; Lee, I.B. How should composite be layered to reduce shrinkage stress: Incremental or bulk filling? Dent. Mater. 2008, 24, 1501–1505. [Google Scholar] [CrossRef]
  38. Roggendorf, M.J.; Krämer, N.; Appelt, A.; Naumann, M.; Frankenberger, R. Marginal quality of flowable 4-mm base vs. conventionally layered resin composite. J. Dent. 2011, 39, 643–647. [Google Scholar] [CrossRef]
  39. Erdemir, U.; Yildiz, E.; Eren, M.M.; Ozel, S. Surface hardness evaluation of different composite resin materials: Influence of sports and energy drinks immersion after a short-term period. J. Appl. Oral Sci. 2013, 21, 124–131. [Google Scholar] [CrossRef] [Green Version]
  40. Sarikaya, I.B.; Güler, A.U. Effects of different surface treatments on the color stability of various dental porcelains. J. Dent. Sci. 2011, 6, 65–71. [Google Scholar] [CrossRef] [Green Version]
  41. Badra, V.V.; Faraoni, J.J.; Ramos, R.P.; Palma-Dibb, R.G. Influence of different beverages on the microhardness and surface roughness of resin composites. Oper. Dent. 2005, 30, 213–219. [Google Scholar]
  42. Catelan, A.; Briso, A.L.; Sundfeld, R.H.; Dos Santos, P.H. Effect of artificial aging on the roughness and microhardness of sealed composites. J. Esthet. Restor. Dent. 2010, 22, 324–330. [Google Scholar] [CrossRef] [PubMed]
  43. Erdemir, U.; Yildiz, E.; Eren, M.M.; Ozel, S. Surface hardness of different restorative materials after long-term immersion in sports and energy drinks. Dent. Mater. J. 2012, 31, 729–736. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  44. Yap, A.U.; Chew, C.L.; Ong, L.F.; Teoh, S.H. Environmental damage and occlusal contact area wear of composite restoratives. J. Oral Rehabil. 2002, 29, 87–97. [Google Scholar] [CrossRef] [PubMed]
  45. Sunbul, H.A.; Silikas, N.; Watts, D.C. Surface and bulk properties of dental resin- composites after solvent storage. Dent. Mater. 2016, 32, 987–997. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  46. Poggio, C.; Arciola, C.R.; Rosti, F.; Scribante, A.; Saino, E.; Visai, L. Adhesion of Streptococcus mutans to different restorative materials. Int. J. Artif. Organs. 2009, 32, 671–677. [Google Scholar] [CrossRef] [PubMed]
  47. Scribante, A.; Bollardi, M.; Chiesa, M.; Poggio, C.; Colombo, M. Flexural Properties and Elastic Modulus of Different Esthetic Restorative Materials: Evaluation after Exposure to Acidic Drink. Biomed. Res. Int. 2019, 2019, 5109481. [Google Scholar] [CrossRef] [PubMed]
  48. Brambilla, E.; Gagliani, M.; Ionescu, A.; Fadini, L.; García-Godoy, F. The influence of light-curing time on the bacterial colonization of resin composite surfaces. Dent. Mater. 2009, 25, 1067–1072. [Google Scholar] [CrossRef]
  49. Brambilla, E.; Ionescu, A.; Gagliani, M.; Cochis, A.; Arciola, C.R.; Rimondini, L. Biofilm formation on composite resins for dental restorations: An in situ study on the effect of chlorhexidine mouthrinses. Int. J. Artif. Organs. 2012, 35, 792–799. [Google Scholar] [CrossRef]
  50. Poggio, C.; Dagna, A.; Chiesa, M.; Colombo, M.; Scribante, A. Surface roughness of flowable resin composites eroded by acidic and alcoholic drinks. J. Conserv. Dent. 2012, 15, 137–140. [Google Scholar] [CrossRef] [Green Version]
  51. Buzalaf, M.A.; Hannas, A.R.; Kato, M.T. Saliva and dental erosion. J. Appl. Oral Sci. 2012, 20, 493–502. [Google Scholar] [CrossRef] [Green Version]
Materials 13 01308 g001 550
Figure 1. Flow chart showing how samples were divided into groups and subgroups and the respective treatment assigned. CTR: subgroup of control.
Figure 1. Flow chart showing how samples were divided into groups and subgroups and the respective treatment assigned. CTR: subgroup of control.
Materials 13 01308 g001
Materials 13 01308 g002 550
Figure 2. Mean Vickers hardness number and standard deviation for each tested material, considering both the external and the internal side of the samples. A: External side; B: Internal side.
Figure 2. Mean Vickers hardness number and standard deviation for each tested material, considering both the external and the internal side of the samples. A: External side; B: Internal side.
Materials 13 01308 g002
Materials 13 01308 g003 550
Figure 3. Mean Vickers hardness number and standard deviation for each tested material, considering the two different acid storages compared to a subgroup of control.
Figure 3. Mean Vickers hardness number and standard deviation for each tested material, considering the two different acid storages compared to a subgroup of control.
Materials 13 01308 g003
Table
Table 1. Characteristics of the materials tested in this study.
Table 1. Characteristics of the materials tested in this study.
GroupMaterialCodeTypeCompositionFiller Content %Lot #Manufacturer
1VisCalor bulkVISTermoviscous bulk-fill composite (nanofilled composite)Matrix: Bis-GMA, aliphatic dimethacrylate
Filler: Inorganic filler		83 (w/w)76292Voco, Cuxhaven, Germany
2Admira Fusion x-traFUSNano-hybrid ORMOCER®-based materialMatrix: ORMOCER®
Filler: glass ceramics, silica nanoparticles, pigments		84 (w/w)1750435
1904427		Voco, Cuxhaven, Germany
3x-tra filXTFLight-curing posterior filling materialMatrix: dimethacrylate (Bis-GMA, TEGDMA, UDMA)
Filler: Inorganic filler (Bariumaluminium silicate, fumed silica, pigments)		86 (w/w)1906144Voco, Cuxhaven, Germany
4GrandioSO x-traGRAAestethic nanohybrid bulk restorative materialMatrix: Bis-GMA, Bis-EMA, aliphatic dimethacrylate
Filler: Inorganic filler, organically modified silica		86 (w/w)1907626Voco, Cuxhaven, Germany
Table
Table 2. Descriptive statistics of VHN for each tested material, considering both the external and the internal side of the samples.
Table 2. Descriptive statistics of VHN for each tested material, considering both the external and the internal side of the samples.
GroupMaterial CodeSideMeanMinMdnMax
1VISExternal (A)82.82 (1.62) a80.1083.2185.10
1VISInternal (B)67.80 (2.51) b64.6067.6572.30
2FUSExternal (A)62.08 (0.92) c60.5862.2963.08
2FUSInternal (B)53.14 (2.31) d50.1053.1257.00
3XTFExternal (A)87.00 (1.97) e84.4087.2090.50
3XTFInternal (B)82.80 (2.28) a78.9083.0086.20
4GRAExternal (A)71.50 (1.70) f68.3072.1573.44
4GRA Internal (B)65.60 (1.28) b63.8065.7067.20
SD: standard deviation; Min: minimum value; Mdn: median; Max: maximum value. Superscript letters (a, b, c, d, e and f) have been used to indicate statistical results: different letters indicate the presence of significant differences in micro-hardness among the groups (significance was set at P < 0.05).
Table
Table 3. Mean percentage micro-hardness loss of the internal side of each tested material, compared to the external side.
Table 3. Mean percentage micro-hardness loss of the internal side of each tested material, compared to the external side.
GroupMaterial CodeMean Percentage Loss (SD) %
1VIS−18.14 (0.02) a
2FUS−14.40 (0.04) b
3XTF−4.79 (0.03) c
4GRA−8.22 (0.02) d
SD: standard deviation. Superscript letters (a, b, c and d) have been used to indicate statistical results: different letters among the groups indicate significant difference in mean percentage loss among the groups (significance was set at P < 0.05).
Table
Table 4. Hardness ratio of each tested material. SD: standard deviation.
Table 4. Hardness ratio of each tested material. SD: standard deviation.
GroupMaterial CodeHardness Ratio (SD)
1VIS0.82 (0.02)
2FUS0.86 (0.04)
3XTF0.95 (0.03)
4GRA0.92 (0.02)
Table
Table 5. Descriptive statistics of VHN for each tested material, considering two different acid storages compared to a group control.
Table 5. Descriptive statistics of VHN for each tested material, considering two different acid storages compared to a group control.
SubgroupsMaterial CodeStorageMean (SD)MinMdnMax
1AVISControl82.82 (1.62) a80.1083.2185.10
1BVIS1-day acid drink76.76 (1.75) b73.4077.0878.77
1CVIS1-week acid drink71.70 (1.68) c69.6071.6574.70
2AFUSControl62.08 (0.92) d60.5862.2963.08
2BFUS1-day acid drink57.22 (1.03) e55.7257.6558.40
2CFUS1-week acid drink53.80 (0.92) f52.3053.9055.00
3AXTFControl87.00 (1.97) g84.4087.2090.50
3BXTF1-day acid drink84.06 (2.02) a80.2084.4386.41
3CXTF1-week acid drink79.04 (2.01) b76.4079.5781.60
4AGRAControl71.50 (1.70) c68.3072.1573.44
4BGRA1-day acid drink67.90 (1.35) h65.8068.2069.36
4CGRA1-week acid drink62.96 (1.26) d61.3063.0864.90
SD: standard deviation; Min: minimum value; Mdn: median; Max: maximum value. Superscript letters (a, b, c, d, e and f) have been used to indicate statistical results: different letters indicate the presence of significant differences in micro-hardness among the groups (significance was set at P < 0.05).
Table
Table 6. Mean percentage micro-hardness loss for the tested materials between different immersion protocols. T0: controls; T1: 1-day storage; T2: 7-day storage.
Table 6. Mean percentage micro-hardness loss for the tested materials between different immersion protocols. T0: controls; T1: 1-day storage; T2: 7-day storage.
GroupMaterial CodeT0–T1 (%)T1–T2 (%)T0–T2 (%)
1VIS−7.30 (2.05) a−6.58 (1.85) a−13.42 (1.72) b
2FUS−7.83 (0.57) a−5.97 (0.72) a−13.34 (0.50) b
3XTF−3.36 (2.07) c−5.92 (3.55) a,c−9.12 (2.68) a,d
4GRA−5.02 (1.27) a−7.27 (0.99) a−11.92 (1.77) b,d
Superscript letters (a, b, c, and d) have been used to indicate statistical results: different letters indicate the presence of significant differences in mean percentage micro-hardness loss among the groups (significance was set at P < 0.05).
Table
Table 7. Linear regression model of the variable Vickers hardness over time.
Table 7. Linear regression model of the variable Vickers hardness over time.
CoefficientEstimateStd. Errort ValuePr(>|t|)ConfidenceIntervals
Intercept74.351.2161.41<0.000171.9776.72
Time−0.045970.01−3.72<0.0001−0.07−0.02

Share and Cite

MDPI and ACS Style

Colombo, M.; Gallo, S.; Poggio, C.; Ricaldone, V.; Arciola, C.R.; Scribante, A. New Resin-Based Bulk-Fill Composites: in vitro Evaluation of Micro-Hardness and Depth of Cure as Infection Risk Indexes. Materials 2020, 13, 1308. https://doi.org/10.3390/ma13061308

AMA Style

Colombo M, Gallo S, Poggio C, Ricaldone V, Arciola CR, Scribante A. New Resin-Based Bulk-Fill Composites: in vitro Evaluation of Micro-Hardness and Depth of Cure as Infection Risk Indexes. Materials. 2020; 13(6):1308. https://doi.org/10.3390/ma13061308

Chicago/Turabian Style

Colombo, Marco, Simone Gallo, Claudio Poggio, Vittorio Ricaldone, Carla Renata Arciola, and Andrea Scribante. 2020. "New Resin-Based Bulk-Fill Composites: in vitro Evaluation of Micro-Hardness and Depth of Cure as Infection Risk Indexes" Materials 13, no. 6: 1308. https://doi.org/10.3390/ma13061308

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop