Search Results (9)

Vertical seismic profiling (VSP) with distributed acoustic sensing (DAS) is an increasingly popular evolving technique for reservoir monitoring. DAS technology enables permanent fibre installations in wells and simultaneous seismic data recording along an entire borehole. Deploying the receivers closer to the reservoir allows for better detectability of smaller signals. A high level of repeatability is essential for the robust time-lapse monitoring of geological reservoirs. One of the prominent factors of repeatability degradation is a shift between source/receiver locations (mispositioning) during baseline and monitor surveys. While the mispositioning effect has been extensively studied for surface 4D seismic, the number of such studies for VSP is quite limited. To study the effects of source mispositioning on time-lapse data repeatability, we performed two VSP experiments at two on-shore sites with vibroseis. The first study was carried out at the Otway International Test Centre during Stage 3 of the Otway project and showed that the effect of source mispositioning on repeatability is negligible in comparison with the effect of temporal variations of the near-surface conditions. To avoid these limitations, we conducted a same-day controlled experiment at the Curtin University site. This second experiment showed that the effect of source mispositioning on repeatability is controlled by the degree of lateral variations of the near-surface conditions. Unlike in marine seismic measurements, lateral variations of near-surface properties can be strong and rapid and can degrade the repeatability for shifts of the source of a few meters. The greater the mispositioning, the higher the chance of such significant variations. When the near-surface conditions are laterally homogeneous, the effect of typical source mispositioning is small, and in all practical monitoring applications its contribution to non-repeatability is negligible. Full article

Seismic velocities and elastic moduli of rocks are known to vary significantly with applied stress, which indicates that these materials exhibit nonlinear elasticity. Monochromatic waves in nonlinear elastic media are known to generate higher harmonics and combinational frequencies. Such effects have the potential to be used for broadening the frequency band of seismic sources, characterization of the subsurface, and safety monitoring of civil engineering infrastructure. However, knowledge on nonlinear seismic effects is still scarce, which impedes the development of their practical applications. To explore the potential of nonlinear seismology, we performed three experiments: two in the field and one in the laboratory. The first field experiment used two vibroseis sources generating signals with two different monochromatic frequencies. The second field experiment used a surface orbital vibrator with two eccentric motors working at different frequencies. In both experiments, the generated wavefield was recorded in a borehole using a fiber-optic distributed acoustic sensing cable. Both experiments showed combinational frequencies, harmonics, and other intermodulation products of the fundamental frequencies both on the surface and at depth. Laboratory experiments replicated the setup of the field test with vibroseis sources and showed similar nonlinear combinations of fundamental frequencies. Amplitudes of the nonlinear signals observed in the laboratory showed variation with the saturating fluid. These results confirm that nonlinear components of the wavefield propagate as body waves, are likely to generate within rock formations, and can be potentially used for reservoir fluid characterization. Full article

The technique of the source array based on the vibroseis can provide the strong energy of a seismic wave field, which better meets the need for seismic exploration. The seismic coherent noise reduces the signal-to-noise ratio (SNR) of the source array seismic data and affects the seismic data processing. The traditional coherent noise removal methods often cause some damage to the effective signal while suppressing coherent noise or cannot suppress the interference wave effectively at all. Based on the multi-scale and multi-direction properties of the non-subsampled Shearlet transform (NSST) and its simple mathematical structure, the seismic coherent noise removal method of source array in NSST domain is proposed. The method is applied to both the synthetic seismic data and the filed seismic data. After processing with this method, the coherent noise of the seismic data is greatly removed and the effective signal information is greatly protected. The analysis of the results demonstrates the effectiveness and practicability of the proposed method on coherent noise attenuation. Full article

In the presented study, multi-parameter inversion in the presence of attenuation is used for the reconstruction of the P- and the S- wave velocities and the density models of a synthetic shallow subsurface structure that contains a dipping high-velocity layer near the surface with varying thicknesses. The problem of high-velocity layers also complicates selection of an appropriate initial velocity model. The forward problem is solved with the finite difference, and the inverse problem is solved with the preconditioned conjugate gradient. We used also the adjoint wavefield approach for computing the gradient of the misfit function without explicitly build the sensitivity matrix. The proposed method is capable of either minimizing the least-squares norm of the data misfit or use the Born approximation for estimating partial derivative wavefields. It depends on which characteristics of the recorded data—such as amplitude, phase, logarithm of the complex-valued data, envelope in the misfit, or the linearization procedure of the inverse problem—are used. It showed that by a pseudo-viscoelastic time-domain full-waveform inversion, structures below the high-velocity layer can be imaged. However, by inverting attenuation of P- and S- waves simultaneously with the velocities and mass density, better results would be obtained. Full article

Seismic communication might promise to revolutionize the theory of seismic waves. However, one of the greatest challenges to its widespread adoption is the difficulty of signal extraction because the seismic waves in the vibration environments, such as seas, streets, city centers and subways, are very complex. Here, we employ segmented correlation technology with Morse code (SCTMC), which extracts the target signal by cutting the collected data into a series of segments and makes these segments cross-correlate with the decoded signal to process the collected data. To test the effectiveness of the technology, a seismic communication system composed of vibroseis sources and geophones was built in an environment full of other vibration signals. Most notably, it improves the signal-to-noise ratio (SNR), extending the relay distance and suppressing other vibration signals by using technology to deal with seismic data generated by the system. Full article

Concerns about the potential environmental impacts of geophysical surveys using air gun sources, coupled with advances in geophysical surveying technology and data processing, are driving research and development of commercially viable alternative technologies such as marine vibroseis (MV). MV systems produce controllable acoustic signals through volume displacement of water using a vibrating plate or shell. MV sources generally produce lower acoustic pressure and reduced bandwidth (spectral content) compared to air gun sources, but to be effective sources for geophysical surveys they typically produce longer duration signals with short inter-signal periods. Few studies have evaluated the potential effects of MV system use on marine fauna. In this desktop study, potential acoustic exposure of marine mammals was estimated for MV and air gun arrays by modeling the source signal, sound propagation, and animal movement in representative survey scenarios. In the scenarios, few marine mammals could be expected to be exposed to potentially injurious sound levels for either source type, but fewer were predicted for MV arrays than air gun arrays. The estimated number of marine mammals exposed to sound levels associated with behavioral disturbance depended on the selection of evaluation criteria. More behavioral disturbance was predicted for MV arrays compared to air gun arrays using a single threshold sound pressure level (SPL), while the opposite result was found when using frequency-weighted sound fields and a multiple-step, probabilistic, threshold function. Full article

A 10.5 km² 3D seismic survey was acquired over the Kylylahti mine area (Outokumpu mineral district, eastern Finland) as a part of the COGITO-MIN (COst-effective Geophysical Imaging Techniques for supporting Ongoing MINeral exploration in Europe) project, which aimed at the development of cost-effective geophysical imaging methods for mineral exploration. The cost-effectiveness in our case was related to the fact that an active-source 3D seismic survey was accomplished by using the receiver spread originally designed for a 3D passive survey. The 3D array recorded Vibroseis and dynamite shots from an active-source 2D seismic survey, from a vertical seismic profiling experiment survey, as well as some additional “random” Vibroseis and dynamite shots made to complement the 3D source distribution. The resulting 3D survey was characterized by irregular shooting geometry and relatively large receiver intervals (50 m). Using this dataset, we evaluate the effectiveness of the standard time-imaging approach (post-stack and pre-stack time migration) compared to depth imaging (standard and specialized Kirchhoff pre-stack depth migration, KPreSDM). Standard time-domain processing and imaging failed to convincingly portray the first ~1500 m of the subsurface, which was the primary interest of the survey. With a standard KPreSDM, we managed to obtain a good image of the base of the Kylylahti formation bordering the extent of the mineralization-hosting Outokumpu assemblage rocks, but otherwise the image was very noisy in the shallower section. The specialized KPreSDM approach (i.e., coherency-based Fresnel volume migration) resulted in a much cleaner image of the shallow, steeply dipping events, as well as some additional deeper reflectors, possibly representing repetition of the contact between the Outokumpu assemblage and the surrounding Kalevian metasediments at depth. Full article

We show that by using an advanced pre-stack depth imaging algorithm it is possible to retrieve meaningful and robust seismic images with sparse shot points, using only 3–4 source points per kilometer along a seismic profile. Our results encourage the use of 2D seismic reflection profiling as a reconnaissance tool for mineral exploration in areas with limited access for active seismic surveys. We used the seismic data acquired within the COGITO-MIN project comprising two approximately 6 km long seismic reflection profiles at the polymetallic Kylylahti massive sulfide mine site in eastern Finland. The 2D seismic data acquisition utilized both Vibroseis and dynamite sources with 20 m spacing and wireless receivers spaced every 10 m. For both source types, the recorded data show clear first breaks over all offsets and reflectors in the raw shot gathers. The Kylylahti area is characterized by folded and faulted, steeply dipping geological contacts and structures. We discuss post-stack and pre-stack data processing and compare time and depth imaging techniques in this geologically complex Precambrian hardrock area. The seismic reflection profiles show prominent reflectors at 4.5–8 km depth utilizing different migration routines. In the shallow subsurface, steep reflectors are imaged, and within and underneath the known Kylylahti ultramafic body reflectivity is prominent but discontinuous. Full article

In March 2016, arguably the most ambitious 4D (3D space + over time) active-source seismic survey for geothermal exploration in the U.S. was acquired at Brady Natural Laboratory, outside Fernley, Nevada. The four-week experiment included 191 vibroseis source locations, and approximately 130 m of distributed acoustic sensing (DAS) in a vertical well, located at the southern end of the survey area. The imaging of the geothermal faults is done with reverse time migration of the DAS data for both P-P and P-S events in order to generate 3D models of reflectivity, which can identify subsurface fault locations. Three scenarios of receiver data are explored to investigate the reliability of the reflectivity models obtained: (1) Migration of synthetic P-P and P-S DAS data, (2) migration of the observed field DAS data and (3) migration of pure random noise to better assess the validity of our results. The comparisons of the 3D reflectivity models from these three scenarios confirm that sections of three known faults at Brady produce reflected energy observed by the DAS. Two faults that are imaged are ~1 km away from the DAS well; one of these faults (middle west-dipping) is well-constructed for over 400 m along the fault’s strike, and 300 m in depth. These results confirm that the DAS data, together with an imaging engine such as reverse time migration, can be used to position important geothermal features such as faults. Full article