Search Results (6)

Background: Sacroiliac screw fixation in elderly patients with pelvic fractures remains a challenging procedure for stabilization due to impaired bone quality. To improve it, we investigated the biomechanical properties of combined oblique sacroiliac and transiliosacral screw stabilization versus the additional cement augmentation of this construct in a cadaver model of osteoporotic bone, specifically with respect to the maximal force stability and fracture-site motion in the displacement and rotation of fragments. Methods: Standardized complete sacral fractures with intact posterior ligaments were created in osteoporotic cadaver pelvises and stabilized with a triangle of two oblique sacroiliac screws from each side with an additional transiliosacral screw in S1 (n = 5) and using the same pelvises with additional cement augmentation (n = 5). A short cyclic loading protocol was applied, increasing the axial force up to 125 N. Sacral fracture-site motion in displacement and rotation of the fragments was measured by optical motion tracking. Results: A maximum force of 65N +/− 12.2 N was achieved using the triangular screw stabilization of the sacrum. Cement augmentation did not provide any significant gain in maximum force (70 N +/− 29.2 N). Only low fragment displacement was observed (2.6 +/− 1.5 mm) and fragment rotation (1.3 +/− 1.2°) without increased stability (3.0 +/− 1.5 mm; p = 0.799; 1.7 +/− 0.4°; p = 0.919) following the cement augmentation. Conclusions: Triangular stabilization using two obliques and an additional transiliosacral screw provides sufficient primary stability of the sacrum. Still, the stability achieved seems very low, considering the forces acting in this area. However, additional cement augmentation did not increase the stability of the sacrum. Given its lack of beneficial abilities, it should be used carefully, due to related complications such as cement leakage or nerve irritation. Improving the surgical methods used to stabilize the posterior pelvic ring will be a topic for future research. Full article

Background/Objectives: Osteoporosis is a global problem that will increase as the population increases and ages, requiring prevention, early detection, and appropriate treatment. An increasing loss in bone mineral density (BMD) is the hallmark of osteoporosis, leading to an increased risk for insufficiency fractures. We aimed to investigate and analyze the applicability of native lumbar spine computed tomography (CT) scans for the evaluation of bone density compared with standard bone density measurements with quantitative computed tomography (QCT) and computed tomography X-ray absorptiometry of the hip (CTXA). Methods: Patients who were referred to our institution for diagnostic investigations and underwent CT imaging of the lumbar spine, as well as standard osteoporosis assessments including QCT and CTXA, were included in the study, resulting in a total of 240 patients (mean age: 65.9 years, range: 24–91). An ANOVA test was used to compare patient groups without a fracture, with one fracture, with more than one fracture, and with additional sacral fractures. An ROC analysis was performed to assess the predictive power of fracture risk estimation considering HU, QCT, and CTXA values. Results: At least one fracture was detected in 42.9% of these patients. For the lumbar spine, the median HU was 89.9 (range 67.9–126.9) and the median BMD was 73.7 (range 57.1–104.2) mg/cm³. With a correlation coefficient of 0.98 (p < 0.001), the HU values obtained from native lumbar CT scans can be calculated using the following formula: BMDspine = 0.84 + (0.81 × HU). With HU values < 80 and a BMD of the lumbar spine < 66 mg/cm³, a significantly increased number of osteoporotic vertebral fractures were found in the mid-thoracic, thoracolumbar, and sacral regions with an effect size of 0.89. In 32 patients (13.3%), additional sacral fractures were found; these patients showed the lowest density values with a median HU value of 31.8 (12.7–58.2). An ROC analysis of HU revealed a 93% sensitivity for the coincidence of a vertebral fracture. There was no significant difference compared with the AUC of QCT (p = 0.395) for concomitant vertebral body fractures. CTXA values also allowed for risk assessment but showed a significantly lower AUC. We found a negative correlation of BMD with age and a positive correlation of BMD with body mass index. Conclusions: Cancellous density measurements in HU values can be effectively converted into quantitative BMD values in mg/cm³, enabling a reliable assessment of osteoporosis severity and fracture risk prediction. Further quantitative density evaluation of the hip does not add value to fracture risk assessment for the axial skeleton. Based on this study’s findings, using HU values in native CT of the lumbar spine alone offers a viable, opportunistic approach towards fracture risk evaluation of the spine. Full article

Background: There has been an increasing number of fragility fractures of the sacrum in the recent decade. With rates of up to 28%, the complication rates after surgical treatment are still at an unacceptably high level, and new treatment strategies are urgently needed. Therefore, the purpose of this study was to evaluate the potential of 3D-navigated trans-sacral bar osteosynthesis in the surgical treatment of fragility fractures of the sacrum. Methods: Retrospectively, from 2017 to 2023, all cases with confirmed fragility fractures of the sacrum in patients > 65 years of age that were surgically treated with navigated 3D-navigated trans-sacral bar osteosynthesis were included, and epidemiological data and the course of treatment analyzed in comparison to a matched control group. Results: Finally, 21 patients (18 women and 3 men) were included in this study. The average age of the patients was 82.6 (SD 6.3) in the intervention group and 79.4 (SD 6.7) in the control group. There were postoperatively detected complications in two cases (18%) in the intervention group and in four cases (40%, p = 0.362) in the control group. The postoperative in-hospital stay was 10 days (SD 3.8) vs. 11.4 days (SD 3.8) in the control. None of the patients in the intervention group and two in the control group needed revision surgery. Conclusions: Overall, 3D-navigated trans-sacral bar osteosynthesis seems to be a promising technique, enabling an accurate implant positioning while offering a low complication rate with an excellent short-term outcome in elderly patients with fragility fractures of the sacrum. Full article

(1) Background: Pelvic fractures, and particularly instabilities of the dorsal pelvic ring, are becoming increasingly prevalent, particularly in orthogeriatric patients. Spino-pelvic triangular osteosynthesis is an effective approach to achieve sufficient stabilization in vertically unstable fractures. This study compares two types of osteosynthesis: the conventional one and a novel instrumentation where the iliosacral screw is placed through a fenestrated iliac screw. (2) Methods: Sixteen artificial osteoporotic L5+pelvis models with an unstable sacral fracture have been instrumented with either an iliac screw connected with a rod to a L5 pedicle screw and an iliosacral screw (TF) or a fenestrated ilium screw connected with a rod to a L5 pedicle screw and an iliosacral screw passing through the fenestra of the iliac screw (TFS). Biomechanical testing was performed using cyclic loading until failure. (3) Results: Both configurations yielded comparable results with regard to initial stiffness, implant loosening, and cycles to failure. The TFS exhibited markedly higher values for cycles to failure and markedly lower values for loosening. However, due to the characteristics of the artificial bone model, these findings were not significant. (4) Conclusions: The novel triangular fixation systems demonstrated comparable results to the standard triangular osteosynthesis configuration. Full article

Potential risk factors associated with future osteoporotic vertebral fracture (OVF) were prospectively investigated in middle-aged and older adult women. We enrolled 197 female patients aged ≥50 years who were scheduled to undergo surgery for lower-extremity degenerative diseases. Patient anthropometric and muscle strength measurements, a bone mineral density measurement of the lumbar spine (L-BMD), and full-spine standing radiographs to examine the presence of old OVFs and spinopelvic sagittal parameters were obtained preoperatively. We evaluated 141 patients who underwent full-spine standing radiographs three years postoperatively to identify new OVFs. We excluded 54 patients who did not undergo a second radiographic examination and 2 with new traumatic OVFs. Univariate and multivariate analyses were performed to identify risk factors associated with new non-traumatic OVF occurrence. Ten (7.1%) patients developed new non-traumatic OVFs during the study period (fracture group). The fracture group had less abdominal trunk muscle strength, lower L-BMD, smaller sacral slopes, and larger pelvic tilt than the non-fracture group. The fracture group showed a higher prevalence of old OVFs preoperatively than the non-fracture group. Abdominal trunk muscle weakness, low L-BMD, and the presence of old OVFs were identified as significant risk factors for OVF occurrence. In middle-aged or older adult women, abdominal trunk muscle weakness, low L-BMD, and old OVFs were associated with future OVF. Full article

Background and Objectives: The stability of the pelvic ring mainly depends on the integrity of its posterior part. Percutaneous sacroiliac (SI) screws are widely implanted as standard of care treatment. The main risk factors for their fixation failure are related to vertical shear or transforaminal sacral fractures. The aim of this study was to compare the biomechanical performance of fixations using one (Group 1) or two (Group 2) standard SI screws versus one SI screw with bone cement augmentation (Group 3). Materials and Methods: Unstable fractures of the pelvic ring (AO/OTA 61-C1.3, FFP IIc) were simulated in 21 artificial pelvises by means of vertical osteotomies in the ipsilateral anterior and posterior pelvic ring. A supra-acetabular external fixator was applied to address the anterior fracture. All specimens were tested under progressively increasing cyclic loading until failure, with monitoring by means of motion tracking. Fracture site displacement and cycles to failure were evaluated. Results: Fracture displacement after 500 cycles was lowest in Group 3 (0.76 cm [0.30] (median [interquartile range, IQR])) followed by Group 1 (1.42 cm, [0.21]) and Group 2 (1.42 cm [1.66]), with significant differences between Groups 1 and 3, p = 0.04. Fracture displacement after 1000 cycles was significantly lower in Group 3 (1.15 cm [0.37]) compared to both Group 1 (2.19 cm [2.39]) and Group 2 (2.23 cm [3.65]), p ≤ 0.04. Cycles to failure (Group 1: 3930 ± 890 (mean ± standard deviation), Group 2: 3676 ± 348, Group 3: 3764 ± 645) did not differ significantly between the groups, p = 0.79. Conclusions: In our biomechanical setup cement augmentation of one SI screw resulted in significantly less displacement compared to the use of one or two SI screws. However, the number of cycles to failure was not significantly different between the groups. Cement augmentation of one SI screw seems to be a useful treatment option for posterior pelvic ring fixation, especially in osteoporotic bone. Full article