Search Results (4)

The findings highlight the potential for broadening the use of shell aggregates in construction applications. This research investigated the viability of incorporating milled Acanthocardia tuberculata seashells as fine sand replacements for natural calcareous sand in the production of self-compacting mortar. These results highlight a promising avenue for coastal industries to reduce waste while enhancing the durability of construction materials. Mortar mixtures containing recycled seashell aggregates exhibit superior overall performance compared with those using natural sand in terms of durability, although there is a slight reduction in workability and mechanical strength. Three replacement levels of natural limestone sand (0%, 50%, and 100%) with seashell-based fine aggregates were studied, along with three different powdered/sand ratios. The fresh properties of the mixtures were assessed for workability, whereas the hardened specimens were analyzed using an X-ray technique, thermogravimetry, and differential thermal analysis. Key performance and durability properties, including compressive and flexural strengths, bulk density, porosity, water absorption, dimensional stability, and mercury intrusion porosimetry at 28 days of hardening, were also evaluated. Overall, the incorporation of Acanthocardia tuberculata seashells into cementitious materials supports the principles of the circular economy, providing both environmental and performance advantages. Full article

This study focuses on the feasibility of using ground Acanthocardia tuberculate seashells as fine aggregates for self-compacting mortar production. The obtained results show a promising future for coastal industries as their use eliminates waste products and improves the durability of these materials. The use of Acanthocardia tuberculate recycled aggregate, in terms of durability, improves the performance of all mixes made with seashells compared to those made with natural sand, although it decreases workability and slightly reduces mechanical strength. Proper mix design has beneficial effects, as it improves compressive strength, especially when the powder/sand ratio is 0.7. Three replacement ratios based on the volume (0%, 50%, and 100%) of natural limestone sand with recycled fine aggregate from Acanthocardia tuberculate seashells, and three different dosages modifying the powder/sand ratio (0.6, 0.7, and 0.8), were tested. The fresh-state properties of each self-compacting mixture were evaluated based on workability. The mineralogical phases of the hardened mixtures were characterised using X-ray diffraction, thermogravimetry, and differential analyses. Subsequently, the mechanical and durability properties were evaluated based on the compressive and flexural strengths, dry bulk density, accessible porosity for water and water absorption, drying shrinkage, mercury intrusion porosimetry, and water absorption by capillarity. Therefore, the use of Acanthocardia tuberculate seashells in cement-based systems contributes to circular economy. Full article

Titanium alloys are widely used in various fields, but milling titanium alloy materials often leads to problems such as high milling forces, increased milling temperatures, and chip adhesion. Thus, the machinability of titanium alloys faces challenges. To improve the milling performance of titanium alloy materials, this study analyzes the effective working area on the surface of the milling cutter through mathematical calculations. We design micro-grooves in this area to utilize their friction-reducing and wear-resisting properties to alleviate the aforementioned issues. The effective working area of the ball end milling cutter’s cutting edge is calculated based on the amount of milling and the installation position between the milling cutter and the workpiece. By observing the surface structure of seashells, micro-grooves are proposed and designed to be applied in the working area of the milling cutter surface. The impact of the micro-groove area on the milling cutter surface and spindle speed on milling performance is discussed based on milling simulation and experimental tests. Experimental results show that the cutting force, milling temperature, and chip resistance to adhesion produced by micro-groove milling cutters are superior to conventional milling cutters. Milling cutters with three micro-grooves perform best at different spindle speeds. This is because the presence of micro-grooves on the surface of the milling cutter improves the friction state, promoting a reduction in milling force, while the micro-grooves also serve as storage containers for chips, alleviating the phenomenon of chip softening and adhesion to the cutter. When conducting cutting tests with a milling cutter that has three micro-grooves, the milling force is reduced by 10% to 30%, the milling temperature drops by 10% to 20%, and the surface roughness decreases by 8% to 12%. Full article

Waste seashell (scallop shell)-based adsorbent was prepared via mechanochemical reaction with sodium oxalate using ball milling. The oxalate-modified seashell-based adsorbents (OS) were prepared by varying the molar ratio of calcium and oxalate to 0.5, 1, and 2. Sodium oxalate was used as the aqueous solution in ball milling. Lead ion adsorption was conducted with the prepared adsorbent. The adsorption behavior of lead ions was investigated in terms of adsorption kinetics and adsorption equilibrium. The time course of the amount of Pb adsorbed agreed well with Langmuir rate equation. The adsorption equilibrium relationship of OS adsorbent and Pb agreed well with the Langmuir adsorption isotherm. Increasing with the molar ratio, the saturated amount of Pb adsorbed increased slightly from 5.45 × 10⁻³ to 6.23 × 10⁻³ mol/g. Under the present experimental conditions, the maximum equilibrium adsorption was 5.93 × 10⁻³ mol/g, which is greater than that reported in the literature. Full article