Search Results (8)

In many situations in everyday life, sunlight levels need to be reduced. Optical filters with asymmetric transmittance dependent on the incident angle would be useful for sunglasses and vehicle or architectural windows, among others. Herein, we realized the production of optical filters, called “louver filters”, comprising HAN-type LC film produced using liquid crystalline ink with dichroic dyes. For the formation of the HAN-type LC film, the liquid crystalline ink was aligned on a rubbed polyimide layer and polymerized by UV irradiation. Two kinds of filters are proposed: one is a filter composed of HAN-type LC film and a polarizer, and the other is composed of two HAN-LC films with a half-wave plate between them. The dependence of the asymmetric transmittance on the incident angle was confirmed for these filters. The dependence changed depending on the pretilt angle of the alignment layers. Photographs taken with the optical filters displayed their effectiveness. Full article

Liquid crystal elastomers (LCEs) are polymer networks that exhibit anisotropic liquid crystalline properties while maintaining the properties of elastomers, presenting reversible high-speed and large-scale actuation in response to external stimuli. Herein, we formulated a non-toxic, low-temperature liquid crystal (LC) ink for temperature-controlled direct ink writing 3D printing. The rheological properties of the LC ink were verified under different temperatures given the phase transition temperature of 63 °C measured by the DSC test. Afterwards, the effects of printing speed, printing temperature, and actuation temperature on the actuation strain of printed LCEs structures were investigated within adjustable ranges. In addition, it was demonstrated that the printing direction can modulate the LCEs to exhibit different actuation behaviors. Finally, by sequentially conforming structures and programming the printing parameters, it showed the deformation behavior of a variety of complex structures. By integrating with 4D printing and digital device architectures, this unique reversible deformation property will help LCEs presented here apply to mechanical actuators, smart surfaces, micro-robots, etc. Full article

During water electrolysis, adding an electrocatalyst for the hydrogen evolution reaction (HER) is necessary to reduce the activation barrier and thus enhance the reaction rate. Metal chalcogenide-based 2D nanomaterials have been studied as an alternative to noble metal electrocatalysts because of their interesting electrocatalytic properties and low costs of production. However, the difficulty in improving the catalytic efficiency and industrializing the synthetic methods have become a problem in the potential application of these species in electrocatalysis. Liquid-phase exfoliation (LPE) is a low-cost and scalable technique for lab- and industrial-scale synthesis of 2D-material colloidal inks. In this work, we present, to the best of our knowledge, for the first time a systematic study on the surfactant-assisted LPE of bulk Bi₂S₃ crystalline powder to produce nanosheets (NSs). Different dispersing agents and LPE conditions have been tested in order to obtain colloidal low-dimensional Bi₂S₃ NSs in H₂O at optimized concentrations. Eventually, colloidally stable layered nano-sized Bi₂S₃ suspensions can be produced with yields of up to ~12.5%. The thus obtained low-dimensional Bi₂S₃ is proven to be more active for HER than the bulk starting material, showing an overpotential of only 235 mV and an optimized Tafel slope of 125 mV/dec. Our results provide a facile top-down method to produce nano-sized Bi₂S₃ through a green approach and demonstrate that this material can have a good potential as electrocatalyst for HER. Full article

The recent advent of two-dimensional (2D) materials has had a ground-breaking impact on science and technology. To exploit in technology their unique thickness-dependent physicochemical properties, the large-scale production of 2D materials is mandatory, but it represents an open challenge still due to various pitfalls and severe limitations including the toxicity of state-of-the-art solvents. Thus, liquid-phase exfoliation based on green and bioderived solvents represents an ideal methodology for massive production. This is particularly crucial for introducing 2D materials in technological applications such as the production of drinking water and agri-food industrial processes. Here, we assessed the production of 2D nanosheets (specifically, graphene, WS₂, MoS₂) with liquid-phase exfoliation assisted by eco-friendly solvents, with a comparative evaluation of green solvents in terms of the yield and, moreover, the aspect ratio, defectivity, and crystalline quality of the produced nanosheets. In particular, we focus on the most promising green solvents in terms of the yield and the crystalline quality of the produced nanosheets: Polarclean, Iris, and Cyrene, which were compared with acetone/water mixtures, isopropyl alcohol (IPA), triethanolamine (TEA), aqueous solutions of urea, and an ethanol/water mixture as well as two toxic solvents largely used for the production of 2D nanosheets: N-methyl-2-pyrrolidone (NMP) and N, N-dimethylformamide (DMF). Remarkably, the density of defects was particularly low in the liquid-phase exfoliation with Polarclean, as indicated by the Raman spectrum of graphene, with the I(D)/I(G) ratio below 0.1. Furthermore, Polarclean and Iris also enable ink-jet printing with functional inks of 2D materials based on green solvents due to their low dynamic viscosity at room temperature. Full article

Radioactive iodine-capturing materials are urgently needed for the emerging challenges in nuclear waste disposal. The various pore structures of covalent organic frameworks (COFs) render them promising candidates for efficient iodine adsorption. However, the detailed structure–property relationship of COFs in iodine adsorption remains elusive. Herein, two polymorphic COFs with significantly different crystalline structures are obtained based on the same building blocks with varied molecular ratios. The two COFs both have high crystallinity, high specific surface area, and excellent chemical and thermal stability. Compared with the [C₄+C₄] topology (PyT-2) with an AA stacking form, the [C₄+C₂] topology (PyT-1) with an AB stacking form has more twisted pore channels and complex ink-bottle pores. At ambient conditions, PyT-1 and PyT-2 both exhibit good adsorption properties for iodine capture either in a gaseous or liquid medium. Remarkably, PyT-1 presents an excellent maximum adsorption capacity (0.635 g g⁻¹), and the adsorption limit of PyT-2 is 0.445 g g⁻¹ in an n-hexane solution with an iodine concentration of 400 mg L⁻¹, which is highly comparable to the state-of-the-art iodine absorption performance. This study provides a guide for the future molecular design strategy toward novel iodine adsorbents. Full article

Two polymerizable ionic liquids (or monomeric ionic liquids, mILs) namely 1-butyl-3-methylimidazolium and choline acrylates ([C₄mim]A and ChA, respectively) were synthesized using the modified Fukumoto method from corresponding chlorides. The chemical structure of the prepared mILs was confirmed with FTIR and NMR study. Investigation of the thermal properties with DSC demonstrates that both mILs have a T_g temperature of about 180 K and a melting point around 310 K. It was shown that the temperature dependence of FTIR confirm the T_g to be below 200. Both mILs exhibited non-Newtonian shear thinning rheological behavior at shear rates >4 s⁻¹. It was shown that [C₄mim]A is able to dissolve bacterial cellulose (BC) leading to a decrease in its degree of polymerization and recrystallisation upon regeneration with water; although in the ChA, the crystalline structure and nanofibrous morphology of BC was preserved. It was demonstrated that the thixotropic and rheological properties of cellulose dispersion in ChA at room temperature makes this system a prospective ink for 3D printing with subsequent UV-curing. The 3D printed filaments based on ChA, containing 2 wt% of BC, and 1% of N,N′-methylenebisacrylamide after radical polymerization induced with 1% 2-hydroxy-2-methylpropiophenone, demonstrated Young’s modulus 7.1 ± 1.0 MPa with 1.2 ± 0.1 MPa and 40 ± 5% of strength and ultimate elongation, respectively. Full article

Thermochromic liquid crystal materials are commonly used in printing inks, opening up a wide range of possible applications. In order to ensure and control the most accurate application, the occurrence of the so-called colour play effect, i.e., the appearance of iridescent (rainbow) colours as a function of temperature, must be determined precisely. For this purpose, the temperature-dependent reflection of a sample must be measured using a spectrometer with an integrating sphere. The same values should be obtained for each sample containing the same thermochromic liquid crystalline material, irrespective of the spectrometer used, integrating sphere, layer thickness and the surface properties of the substrate. To describe this intrinsic property of the thermochromic liquid crystal material, the term communication mechanism might be considered. The research has shown how this mechanism is obtained experimentally. Full article

A systematic study was carried out to investigate the effect of ionic liquid in solid polymer electrolyte (SPE) and its layer morphology on the characteristics of an electrochemical amperometric nitrogen dioxide sensor. Five different ionic liquids were immobilized into a solid polymer electrolyte and key sensor parameters (sensitivity, response/recovery times, hysteresis and limit of detection) were characterized. The study revealed that the sensor based on 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][N(Tf)₂]) showed the best sensitivity, fast response/recovery times, and low sensor response hysteresis. The working electrode, deposited from water-based carbon nanotube ink, was prepared by aerosol-jet printing technology. It was observed that the thermal treatment and crystallinity of poly(vinylidene fluoride) (PVDF) in the solid polymer electrolyte influenced the sensitivity. Picture analysis of the morphology of the SPE layer based on [EMIM][N(Tf)₂] ionic liquid treated under different conditions suggests that the sensor sensitivity strongly depends on the fractal dimension of PVDF spherical objects in SPE. Their deformation, e.g., due to crowding, leads to a decrease in sensor sensitivity. Full article