Search Results (10)

This study investigates the mechanical, tribological, and electrochemical behaviour of a novel precipitation-hardenable martensitic alloy produced by selective laser melting (SLM). The alloy was specifically engineered with an optimised composition, free from cobalt and molybdenum, and featuring reduced nickel content (7 wt.%) and 8 wt.% chromium. It has been developed as a cost-effective and sustainable alternative to conventional maraging steels, while maintaining high mechanical strength and a refined microstructure tailored to the steep thermal gradients inherent to the SLM process. Several ageing heat treatments were assessed to evaluate their influence on microstructure, hardness, tensile strength, retained austenite content, dislocation density, as well as wear behaviour (pin-on-disc test) and corrosion resistance (polarisation curves in 3.5%NaCl). The results indicate that ageing at 540 °C for 2 h offers an optimal combination of hardness (550–560 HV), tensile strength (~1700 MPa), microstructural stability, and wear resistance, with a 90% improvement compared to the as-built condition. In contrast, ageing at 600 °C for 1 h enhances ductility and corrosion resistance (Rp = 462.2 kΩ; Ecorr = –111.8 mV), at the expense of a higher fraction of reverted austenite (~34%) and reduced hardness (450 HV). This study demonstrates that the mechanical, surface, and electrochemical performance of this novel SLM-produced alloy can be effectively tailored through controlled thermal treatments, offering promising opportunities for demanding applications requiring a customised balance of strength, durability, and corrosion behaviour. Full article

High chromium cast iron (HCCI) is widely used in the manufacturing of equipment parts in the fields of mining, cement, electric power, metallurgy, the chemical industry, and paper-making because of its excellent wear and corrosion resistance. Although the microstructure and properties of HCCI can be modified by controlling the casting and heat treatment process, alloying is still the most basic and important method to improve the properties of HCCI. There are about 14 common alloying elements in HCCI, among which nickel, copper, and manganese are typical austenite stabilizing elements, which can increase austenite content and matrix electrode potential. The addition of elements such as silicon, nitrogen, boron, and rare earth (RE) is often small, but it has a significant effect on tailoring the microstructure, thereby improving wear resistance and impact toughness. It was thought that after years of development, the research on the role of the above elements in HCCI was relatively complete, but in the past 5 to 10 years, there has been a lot of new research progress. Moreover, the current development situation of HCCI is still relatively extensive, and there are still many problems regarding the alloying of HCCI to be further studied and solved. In this paper, the research results of austenitic stabilizing elements and modifying elements in HCCI are reviewed. The existing forms, distribution law of these elements in HCCI, and their effects on the microstructure, hardness, wear resistance, and corrosion resistance of HCCI are summarized. Combined with the current research situation, the future research and development direction of HCCI alloying is prospected. Full article

Welded cable composed of nickel–chromium (Ni-Cr) alloy and copper is a crucial component in the resistance heating technology used for heavy oil production. Tungsten inert gas (TIG) welding was employed to join the copper and Ni-Cr alloy using copper filler wire, and the stability of the welded joint was analyzed under high-temperature service conditions. We examined the changes in the microstructure and properties of the welded joint after postweld heat treatment (PWHT) at 600 °C for 3, 6, and 12 days. The results showed that the welded joint was appropriately formed, with fractures occurring in the copper substrate. The average tensile strength of the welded joint was 240 MPa. The copper and nickel dissolved into each other, forming a Cu_0.81Ni_0.19 strengthening phase. A columnar crystal diffusion layer formed at the interface between the Ni-Cr alloy and the fusion zone after welding. Grain boundary migration promoted the continuous growth in the columnar crystals as the PWHT duration increased, eliminating the microdefects and inhomogeneities caused by welding. The microhardness progressively decreased from the Ni-Cr alloy side to the copper side. However, the nanoindentation results at the Ni-Cr fusion line initially decreased and then increased with increasing PWHT duration, which contrasted the overall hardness trend observed across the joint after PWHT. Full article

Silver alloys are often used for electrical switches in railway transportation. However, a well-known issue with these switches is their relatively short application period due to certain disadvantages of silver alloys, mainly their low hardness and low resistance to abrasive wear, in contrast to their excellent electrical conductivity. Therefore, the main goal of this study was to increase or maintain the hardness of the surface layer in order to extend the life of worn parts without compromising their electrical properties. Instead of ceramic particles, as in other studies, metallic powders were used, which could increase the electrical and/or thermal properties of silver alloys. The following work presents the use of laser processing as a relatively new technique for metal and metal alloy surface processing technology. In particular, a process based on the melting of silver (Ag) with metallic powders, such as chromium (Cr) and nickel (Ni) particles, is presented. The aim was for these powders to create intermetallic phases with a silver matrix in the obtained surface layer, significantly improving the mechanical properties based on the formation of the phases coherent or semi-coherent with the silver matrix. Regarding the original practical implications of this work, it was important to investigate the possibility of applying fibre laser for surface property enhancement. The scientific aim was to describe the changes in microstructure and compounds that occurred in the laser-remelted surface silver layer after Ni and Cr particles were fed into the basic silver material. It was concluded that the surface layer obtained after chromium application was without cracks and defects and had a higher hardness than the untreated material. A three-zone structure was also found in the obtained surface layer: (1) the remelted zone, (2) the heat-affected zone, and (3) the matrix material. The remelting zone revealed a higher hardness compared to the untreated material, reaching 92 HV0.3, which is more than twice the initial hardness value. Full article

In the as-annealed condition, the nickel-based Alloy 625 has excellent mechanical and corrosion properties compared to those of common stainless steels. This peculiarity enables its exploitation in several industrial fields at cryogenic and high temperatures and in the presence of severely corrosive atmospheres. However, in this alloy, when high-temperature plastic deformation processes and heat treatments are not carefully optimized, the occurrence of excessive grain coarsening can irremediably deteriorate the mechanical strength, possibly leading to incompatibility with the standard requirements. Therefore, this research work investigated the possibility of adopting single- and double-aging treatments aimed at improving such strength loss. Their optimization involved identifying the best compromise between the hardening effect and the loss in corrosion resistance induced by the simultaneous formation of intergranular chromium-rich carbides during aging. The investigation of the aging treatments was performed using hardness, tensile and intergranular corrosion tests considering different time–temperature combinations in a range from 621 °C to 732 °C. Double aging resulted in a considerable acceleration in the hardening response compared to single aging. However, even after its optimization in terms of both temperature and time, the intergranular corrosion resistance remained a critical aspect. Among all the tested conditions, only single aging at 621 °C for 72 h was acceptable in terms of both mechanical and corrosion properties. The influence of longer exposures will be investigated in a future study. Full article

Heat input, a crucial factor in the optimization of high-temperature thermocouple laser welding, has a significant impact on the appearance and mechanical properties of dissimilar welded joints involving stainless-steel- and nickel-based alloys. This study focuses on laser overlay welding of austenitic stainless steels and nickel-based alloys. The findings indicate that an increase in heat input has a more pronounced effect on the penetration depth and dilution rate. Under high heat input, the weld has cracks, spatter, and other defects. Additionally, considerable amounts of chromium (Cr) and nickel (Ni) elements are observed outside the grain near the crack, and their presence increases with higher heat input levels. Phase analysis reveals the presence of numerous Cr₂Fe₁₄C and Fe₃Ni₂ phases within the weld. The heat input increases to the range of 30–35 J/mm, and the weld changes from shear fracture to tensile fracture. In the center of the molten pool, the Vickers hardness is greater than that of the base metal, while in the fusion zone, the Vickers hardness is lower than that of the base metal. The overall hardness is in a downward trend with the increase of heat input, and the minimum hardness is only 159 HV_0.3 at 40 J/mm. The heat input falls within the range of 28–30 J/mm, and the temperature shock resistance is at its peak. Full article

In modern aviation production, innovative hard-to-machine materials with unique physical and mechanical properties are being used increasingly. When processing such materials, the weakest link in the technological chain of production is the metal-cutting tool. In this paper, to improve the efficiency of the blade cutting of heat-resistant alloys, we propose the use of nanostructured multilayer wear-resistant coatings with subsequent laser processing of the cutting surfaces of the end milling cutters according to various schemes. In this case, an increase in the wear-resistant properties of the cutting edge by 15%–20% is provided due to the formation, at high temperatures, of secondary structures with increased wear resistance and a reduction of the temperature and force loading of contact processes. Methodologically, the work was carried out in several consecutive stages: the first stage was the determination of effective grades of wear-resistant coatings obtained via various installations with their subsequent laser processing during the «SharpMark™ Fiber» installation; at the second stage tribotechnical tests were carried out during the tribometer and adhesion installation; and in the third stage wear-resistant, temperature-force tests were carried out using milling machines in various cutting modes. According to the results of the field tests, the tool durability period was increased by 15%–20%. Full article

The article presents a numerical–experimental approach to the weldability and mechanical resistance of the joint of Alloy 59 (2.4605, nickel-chromium-molybdenum) and S355J2W (1.8965) structural steel manufactured by the MIG process with the use of micro-jet cooling. This research was considered because the standard MIG process does not guarantee the procurement of a mixed hard-rusting structural steel superalloy weld of a repeatable and acceptable quality. Welds made through the classic MIG process express cracks that result from their unfavorable metallographic microstructure, while the joint supported by micro-jet cooling does not reflect any cracks and has a high strength with good flexibility. This was achieved by the application of helium for cooling. The joining technology was also considered in the numerical stage, represented by calculations in situ. For this purpose, the fundamental solution method (FSM) for the simulation of heat transfer during the process of welding with micro-jet cooling was implemented according to the initial boundary value problem (IBVP). The problem was solved employing the method of combining the finite difference method, Picard iterations, approximation by the radial basis function, and the fundamental solution method so as to solve the IVBP. The proposed method was validated by the data and results obtained during in situ experiments. The numerical approach enabled us to obtain variations in the temperature distribution values in HAZ with its different dimensional variants, ranging between 600 °C and 1400 °C. Full article

Laser surface treatment on two different types of nickel–chromium white cast iron (Ni-hard) alloys (Ni-hard 1 and Ni-hard 4) was investigated. Nd:YAG laser of 2.2-kw with continuous wave was used. Ni-hard alloys are promising engineering materials, which are extensively used in applications where good resistance to abrasion wear is essential. The conventional hardening of such alloys leads to high wear resistance nevertheless, the core of the alloy suffers from low toughness. Therefore, it would be beneficial to harden the surface via laser surface technology which keeps the core tough enough to resist high impact shocks. A laser power of different levels (600, 800 and 1000 Watts) corresponding to three different laser scanning speeds (3, 4 and 5 m·min⁻¹) was adopted hoping to reach optimum conditions for wear resistance and impact toughness. The optimum condition for both properties was recorded at heat input of 16.78 J·mm⁻². The present findings reflect that the microhardness values and wear resistance clearly increased after laser hardening by almost three times due to laser surface hardening, whereas, the impact toughness was increased from five joules obtained from conventionally heat-treated samples to 6.4 J as gained from laser-treated samples. Full article

This work presents the improvement of hardfacing welding for American Society for Testing and Materials (ASTM) A572-based high-strength, low-alloy steel by controlling the heating/cooling conditions of welding process. In the welding process, the buffer and hardfacing layers were welded onto A572-based material by a nickel–chromium electrode and chromium carbide electrode, respectively. The base metal and electrode materials were controlled by the heating/cooling process during the welding to reduce excessive stress, which could result in a crack in the specimens. The welded specimens were examined by visual and penetrant inspections for evaluating the welding quality. The macro–micro structure of the deposited layer was investigated; scanning electron microscope with an energy-dispersive X-ray spectrometer (SEM-EDS) and XRD were used to characterize structural properties, elemental compositions, and crystallite sizes of the welded specimens. The surface properties, such as hardness, impact, and abrasive wear of the welded specimens, were tested for evaluation of the wear resistance of the welded specimens. Full article