Search Results (5)

The study reviewed the state of the art of the clinical use of a convergent-neck-designed Prama implant. This implant was introduced approximately 10 years ago and was characterized by a specific and unique convergent neck with a microtextured surface (UTM surface) and Zirconium Titanium (ZirTi) implant body surface. The neck design was developed to adopt the biologically oriented preparation technique (BOPT). A critical analysis of the published clinical studies and an evaluation of the adopted clinical protocols were performed. A total of forty-six articles were eligible to be reviewed. Only sixteen clinical studies reported clinical outcomes on Prama implants, and nine of these were selected having the longest follow-up from different research groups. The clinical follow-up/duration of the studies ranged from 12 months to 6 years. The initially proposed protocols explored neck supracrestal–transmucosal placement and gained interest due to its minimally invasive concept and the ability to proceed without a pre-prosthesis second surgery. The following investigations dedicated attention to the subcrestal or equicrestal implant placement with the conventional flap approach. The clinical studies characterized by the transmucosal exposed neck approach reported high survival rates with a stable bone morphology and reduced bone loss during the follow-up. Further recent implementations included the introduction of different convergent neck heights that need to be evaluated. The use of intraoral scanner technologies and digital workflow resulted in a simpler methodology with control of the marginal crown morphology. The studies support the concept that the hard tissue parameters (such as marginal bone level, MBL) and soft tissue parameters (such as pink esthetic score, PES) were stable or improved during the follow-up. Definitive crowns, designed with low invasiveness for soft tissues, were possible thanks to the morphology of the neck. The clinical studies support the use of the Prama implant with the different neck positions, demonstrating hard tissue preservation and optimal esthetic results in the first years following insertion. However, the current body of evidence is not robust enough to draw definitive conclusions, especially in the long term, and further high-quality research (long-term randomized trials) is required to consolidate these early observations. Full article

The issue of dental implant placement relative to the alveolar crest, whether in supracrestal, equicrestal, or subcrestal positions, remains highly controversial, leading to conflicting data in various studies. Three-dimensional (3D) Finite Element Analysis (FEA) can offer insights into the biomechanical aspects of dental implants and the surrounding bone. A 3D model of the jaw was generated using computed tomography (CT) scans, considering a cortical thickness of 1.5 mm. Subsequently, Morse cone implant–abutment connection implants were virtually positioned at the model’s center, at equicrestal (0 mm) and subcrestal levels (−1 mm and −2 mm). The findings indicated the highest stress within the cortical bone around the equicrestally placed implant, the lowest stress in the −2 mm subcrestally placed implant, and intermediate stresses in the −1 mm subcrestally placed implant. In terms of clinical relevance, this study suggested that subcrestal placement of a Morse cone implant–abutment connection (ranging between −1 and −2 mm) could be recommended to reduce peri-implant bone resorption and achieve longer-term implant success. Full article

Peri-implant bone resorption has been reported around some implants after loading, which could create problems for the peri-implant soft and hard tissues’ long-term stability. The reasons for this are still not known. However, relevant importance could be given to this due to the presence of a bacterial contamination at the micro-gap level between implant and abutment. In this regard, external and internal implant–abutment assemblies have been shown to be much more permeable to bacterial colonization than Cone-Morse or conical connections. The placement of a subcrestal implant could have aesthetic advantages, therefore allowing a better prosthetic emergence profile. In literature, controversial experimental and clinical results have been reported on bone resorption around implants placed equicrestally and subcrestally. Interestingly, Finite Element Analysis (FEA) studies revealed to be extremely useful for assessing the peri-implant bone strain and stress. Thus, this study conducted a FEA evaluation of implants with a Cone-Morse implant–abutment assembly inserted into a bone block model mimicking equicrestal (0 mm) and subcrestal placements (−1 and −2 mm). Results demonstrated that maximum stresses were observed in the cortical bone around equicrestally placed implants, with the lowest in the 2 mm subcrestally placed implant and intermediate stresses within the 1 mm subcrestally placed implant. The cortical bone resulted more stressed under lateral loads than axial loads. In conclusion, this FEA study suggested a subcrestal implant placement ranging between −1 and −2 mm to obtain an adequate peri-implant stress pattern. Full article

Despite high success rates of dental implants, surface exposure may occur as a consequence of biologic width establishment associated with surgery. This prospective split-mouth study evaluated the effect of early implant surface exposure caused by initial bone remodeling on long-term peri-implant bone stability and peri-implant health. Additionally, Oral Health-Related Quality of Life (OHRQoL) was assessed by means of the Oral Health Impact Profile-14 (OHIP-14). Twenty-six patients received two non-splinted implants supporting an overdenture in the mandible by means of locators. One implant was installed equicrestally (control) and the second one was installed subcrestally, taking at least 3 mm soft tissue thickness into account (test). During initial bone remodeling (up to 6 months postoperatively), equicrestal placement yielded 0.68 mm additional surface exposure compared to subcrestal placement (p < 0.001). Afterwards, bone level and peri-implant health were comparable in both treatment conditions and stable up to 5 years. The implant overdenture improved OHRQoL (p < 0.01) and remained unchanged thereafter (p = 0.51). In conclusion, adapting the vertical position of the implant concerning the soft tissue thickness prevents early implant surface exposure caused by initial bone remodeling, but in a well-maintained population, this has no impact on long-term prognosis. The treatment of edentulousness with an implant mandibular overdenture improves OHRQoL. Full article

In fully edentulous patients, the support of a lower dental prosthesis by two implants could improve the chewing ability, retention, and stability of the prosthesis. Despite high success rates of dental implants, complications, such as peri-implantitis, do occur. The latter is a consequence of crestal bone loss and might be related to the implant surface and peri-implant soft tissue thickness. The aim of this paper is to describe the effect of implant surface roughness and soft tissue thickness on crestal bone remodeling, peri-implant health, and patient-centered outcomes. The mandibular overdenture supported by two implants is used as a split-mouth model to scrutinize these aims. The first study compared implants placed equicrestal to implants placed biologically (i.e., dependent on site-specific soft tissue thickness). The second clinical trial compared implants with a minimally to a moderately rough implant neck. Both studies reported an improvement in oral health-related quality of life and a stable peri-implant health after three years follow-up. Only equicrestal implant placement yielded significantly higher implant surface exposure, due to the establishment of the biologic width. Within the limitations of this study, it can be concluded that an implant supported mandibular overdenture significantly improves the quality of life, with limited biologic complications and high survival rates of the implants. Full article