Search Results (4)

Double-Wall Effusion Cooling schemes present an opportunity for aeroengine designers to achieve high overall cooling effectiveness and convective cooling efficiency in High-Pressure Turbine blades with reduced coolant usage compared to conventional cooling technologies. This is accomplished by combining impingement, pin-fin and effusion cooling. Optimising these cooling schemes is crucial to ensuring that cooling is achieved sufficiently at high-heat-flux regions and not overused at low-heat-flux ones. Due to the high number of design variables employed in these systems, optimisation through the use of Computational Fluid Dynamics (CFD) simulations can be a computationally costly and time-consuming process. This study makes use of a Low-Order Flow Network Model (LOM), developed, validated and presented previously, which quickly assesses the pressure, temperature, mass flow and heat flow distributions through a Double-Wall Effusion Cooling scheme. Results generated by the LOM are used to rapidly produce an ideal cooling system design through the use of an Evolutionary Genetic Algorithm (GA) optimisation process. The objective is to minimise the coolant mass flow whilst maintaining acceptable metal cooling effectiveness around the external surface of the blade and ensuring that the Backflow Margin for all film holes is above a selected threshold. For comparison, a Genetic Aggregation model-based optimisation using CFD simulations in ANSYS Workbench is also conducted. Results for both the reduction of coolant mass flow and the total optimisation runtime are analysed alongside those from the LOM, demonstrating the benefit of rapid low-order solving techniques. Full article

The high pressure turbine nozzle guide vane of a modern aeroengine experiences large heat loads and thus requires both highly effective internal and external cooling. This can be accomplished with double-wall effusion cooling, which combines impingement, pin-fin and effusion cooling. The combination of three cooling mechanisms causes high pressure losses, increasing potential for the migration of coolant towards low pressure regions, subsequently starving effusion holes on the leading edge of coolant supply. This paper presents a low order flow network model to rapidly assess the pressure and mass flow distributions through such cooling schemes for a flexible set of geometric and flow conditions. The model is subsequently validated by a series of experiments with varying mainstream pressure gradients. Results from the model are used to indicate design parameters to reduce the effect of coolant migration, and to minimise the risk of destructive hot gas ingestion. Full article

A new experimental study is presented for a combustor with a double-wall cooling design. The inner wall at the hot gas side features effusion cooling with 7-7-7 laidback fan-shaped holes, and the outer wall at the cold side features an impingement hole pattern with circular holes. Data are acquired to asses the thermal and aerodynamic behavior of the setup, using a new, scaled up, engine similar test rig. Similarity includes Reynolds, Nusselt and Biot numbers for hot gas and coolant flow. Different geometrical setups are studied by varying the cavity height between the two walls and the relative alignment of the two hole patterns at two different impingement Reynolds numbers. This article focuses on the aerodynamic performance of the setup. Instationary flow data are acquired, using a high speed stereo PIV setup. For each geometrical configuration, approximately 20 planes are recorded with a data rate of 1000 Hz by traversing the flow region of interest in the cavity between the two specimen. This fine resolution allows the reconstruction of 3D flow fields for the mean data values and an extensive analysis of transient phenomena at each plane. Time averaged data and jet-center plane transient data are presented in detail. The results show a complex flow field with a hexagonal vortex pattern in the cavity, which is mainly influenced by the cavity height and the relative alignment of the two walls. The jet Reynolds number shows small influence when analyzing normalized data. Small cavity heights show a less developed flow field with less stable vortex systems. The alignment shows a similar influence on vortex system stability, with the aligned case performing better. Additionally, statistical analysis of the jet flow and frequency domain analysis of the jet and the effusion flow are presented, showing the damping capability of the cavity, especially at increased cavity heights, and a residual low frequency pulsation of the effusion cooling inflow. Full article

A new experimental study is presented for a combustor with a double-wall cooling design. The inner wall at the hot gas side features effusion cooling with 7-7-7 laidback fan-shaped holes, and the outer wall at the cold side features an impingement hole pattern with circular holes. Data have been acquired to assess the thermal and aerodynamic behavior of the setup using a new, scaled up, engine-similar test rig. Similarity includes Reynolds, Nusselt, and Biot numbers for hot gas and coolant flow. Different geometrical setups are studied by varying the cavity height between the two walls and the relative alignment of the two hole patterns at several different blowing ratios. This article focuses on the thermal performance of the setup. The temperature data are acquired using two infrared systems on either side of the effusion wall specimen. In addition to cooling effectiveness evaluations, finite element simulations are performed, yielding the locally resolved wall heat fluxes. Results are presented for three cavity heights and two longitudinal specimen alignments. The results show that the hot gas side total cooling effectiveness can achieve values as high as 90% and is mainly influenced by the effusion coverage. Impingement cooling has a small influence on overall effectiveness, and the area of influence is mainly located upstream where effusion cooling is not built up completely. The analyzed geometric variations show a major influence on cavity flow and impingement heat transfer. Small cavities lead to constrained flow and high local Nusselt numbers, while larger cavities show more equalized Nusselt number distributions. A present misalignment shows especially high influence at small cavity heights. The largest cavity height, in general, showed a decrease in heat transfer due to reduced jet momentum. Full article