Search Results (6)

This paper presents a practical implementation and measurement results of power-efficient chip performance optimization, utilizing low-cost indirect measurement methods to support self-X properties (self-calibration, self-healing, self-optimization, etc.) for in-field optimization of analog front-end sensory electronics with XFAB 0.35 µm complementary metal oxide semiconductor (CMOS) technology. The reconfigurable, fully differential indirect current-feedback instrumentation amplifier (CFIA) performance is intrinsically optimized by employing a single test sinusoidal signal stimulus and measuring the total harmonic distortion (THD) at the output. To enhance the optimization process, the experience replay particle swarm optimization (ERPSO) algorithm is utilized as an artificial intelligence (AI) agent, implemented at the hardware level, to optimize the performance characteristics of the CFIA. The ERPSO algorithm extends the selection producer capabilities of the classical PSO methodology by incorporating an experience replay buffer to mitigate the likelihood of being trapped in local optima. Furthermore, the CFIA circuit has been integrated with a simple power-monitoring module to assess the power consumption of the optimization solution, to achieve a power-efficient and reliable configuration. The optimized chip performance showed an approximate 34% increase in power efficiency while achieving a targeted THD value of −72 dB, utilizing a 1 Vp-p differential input signal with a frequency of 1 MHz, and consuming approximately 53 mW of power. Preliminary tests conducted on the fabricated chip, using the default configuration pattern extrapolated from post-layout simulations, revealed an unacceptable performance behavior of the CFIA. Nevertheless, the proposed in-field optimization successfully restored the circuit’s performance, resulting in a robust design that meets the performance achieved in the design phase. Full article

A low-noise and -power readout integrated circuit (IC) for two-electrode electrocardiogram (ECG) recording is developed in this study using a common-mode charge pump (CMCP) for a robust 20-V_PP common-mode interference (CMI). Two-electrode ECG recording offers more comfort than three-electrode ECG recording. Contrasting to the three-electrode ECG recording, the two-electrode ECG recording is affected by CMI during measurements; the intervention of a large CMI will distort the ECG signal measurement. To achieve robustness for the CMI, the proposed ECG readout IC adopts CMCP—it uses switched capacitors that store and subtract CMI by control logic. In this paper, a window comparator structure is applied to CMCP to obtain a signal with less distortion. The window voltage ranges were set between the input common-mode ranges in which IA can operate. Therefore, a signal with less distortion was obtained by stopping the operation of CMCP between the window voltage ranges. It also reduced additional current consumption. To achieve this, the proposed circuit is implemented using a chopper stabilization technique. The chopper implemented in the amplifier can reduce low-frequency noise components, such as 1/f noise, and it comprises a CMCP, current feedback instrumentation amplifier, QRS peak detector, relaxation oscillator, voltage reference, timing generator, and serial peripheral interface on a single chip. The proposed circuit was designed using a standard 0.18 μm CMOS process with an active area of 0.54 mm². The proposed CMCP achieves a CMI robustness of 20 V_PP at 60 Hz. The measured input-referred noise level was 119 nV/√Hz at 1 Hz, and the power consumption was 23.83 μW with a 1.8 V power supply. Full article

In this study, we describe a dual-chopper glitch-reduction current-feedback instrumentation amplifier (CFIA) with a ripple reduction loop. The amplifier employs the chopping technique to reduce low-frequency noise, such as 1/f noise. A glitch caused by chopping occurs at each chopper clock edge and results in intermodulation distortion (IMD). Owing to the input offset, the chopping technique also produces ripples. In this study, the glitch-induced IMD was reduced using a fill-in technique whereby only neat signals were alternately used as outputs by avoiding the glitch section with dual-chopping channel CFIA. To avoid using a high-order, low-frequency filter, a ripple reduction loop was implemented to reduce the ripple generated by chopping. The CFIA is based on a low-noise chopper fully differential difference amplifier with a cascode stage and a Monticelli-class AB output stage, which can drive a larger load and increase power efficiency. The proposed dual-chopper CFIA was fabricated using a 0.18 µm CMOS standard process, and its current consumption with a 1.8-V power supply is 29.5 μA. The proposed CFIA has a gain of 51 V/V, input referred noise of 53.3 nV/√Hz at 1 Hz, and a noise efficiency factor of 4.48. Full article

This paper presents a power line interference (PLI) reduction technique with a current-reused current-feedback instrumentation amplifier (CFIA) for electrocardiogram (ECG) recording. In a portable two-electrode ECG monitoring application, the presence of undesired PLI may severely corrupt the quality of ECG recording. Since PLI can be over a few volts, the input signal including the ECG signal can exceed the supply or ground level by an electrostatic discharge (ESD) diode in input/output (I/O) pad. To prevent this problem, this paper presents a continuous-time input common-mode current feedback loop that can limit displacement current from a capacitive coupling between the human body and a power line. The continuous-time input common-mode current feedback loop can clamp an input common-mode voltage to the saturation region of the input transistor of the current-reused CFIA. After the clamping procedure, the clamped input signal is amplified by the current-reused CFIA. The proposed circuit was designed using a 0.18-μm bipolar-complementary metal semiconductor–double-diffused metal oxide semiconductor (BCDMOS) process with an active area of 1.8 mm². The total power consumption is 18 μW with 1.8 V. The input-referred noise and noise efficiency factor (NEF) of the current-reused CFIA is 2.68 μV_RMS and 4.28 with 107 Hz, respectively. Full article

A fully differential multipath current-feedback instrumentation amplifier (CFIA) for a resistive bridge sensor readout integrated circuit (IC) is proposed. To reduce the CFIA’s own offset and 1/f noise, a chopper stabilization technique is implemented. To attenuate the output ripple caused by chopper up-modulation, a ripple reduction loop (RRL) is employed. A multipath architecture is implemented to compensate for the notch in the chopping frequency band of the transfer function. To prevent performance degradation resulting from external offset, a 12-bit R-2R digital-to-analog converter (DAC) is employed. The proposed CFIA has an adjustable gain of 16–44 dB with 5-bit programmable resistors. The proposed resistive sensor readout IC is implemented in a 0.18 μm complementary metal-oxide-semiconductor (CMOS) process. The CFIA draws 169 μA currents from a 3.3 V supply. The simulated input-referred noise and noise efficiency factor (NEF) are 28.3 nV/√Hz and 14.2, respectively. The simulated common-mode rejection ratio (CMRR) is 162 dB, and the power supply rejection ratio (PSRR) is 112 dB. Full article

Micro-electromechanical system (MEMS) magnetic sensors are widely used in the nanosatellites field. We proposed a novel high-precision miniaturized three-axis digital tunneling magnetic resistance-type (TMR) sensor. The design of the three-axis digital magnetic sensor includes a low-noise sensitive element and high-performance interface circuit. The TMR sensor element can achieve a background noise of 150 pT/Hz^1/2 by the vertical modulation film at a modulation frequency of 5 kHz. The interface circuit is mainly composed of an analog front-end current feedback instrumentation amplifier (CFIA) with chopper structure and a fully differential 4th-order Sigma-Delta (ΣΔ) analog to digital converter (ADC). The low-frequency 1/f noise of the TMR magnetic sensor are reduced by the input-stage and system-stage chopper. The dynamic element matching (DEM) is applied to average out the mismatch between the input and feedback transconductor so as to improve the gain accuracy and gain drift. The digital output is achieved by a switched-capacitor ΣΔ ADC. The interface circuit is implemented by a 0.35 μm CMOS technology. The performance test of the TMR magnetic sensor system shows that: at a 5 V operating voltage, the sensor can achieve a power consumption of 120 mW, a full scale of ±1 Guass, a bias error of 0.01% full scale (FS), a nonlinearity of x-axis 0.13% FS, y-axis 0.11% FS, z-axis 0.15% FS and a noise density of x-axis 250 pT/Hz^1/2 (at 1 Hz), y-axis 240 pT/Hz^1/2 (at 1 Hz), z-axis 250 pT/Hz^1/2 (at 1 Hz), respectively. This work has a less power consumption, a smaller size, and higher resolution than other miniaturized magnetometers by comparison. Full article