Search Results (6)

Achieving color match between natural teeth and restorative materials is crucial in dentistry. Factors such as the light source, brightness, and opacity influence tooth color, determined by light absorption and scattering within the material. Advances in CAD/CAM systems have enhanced prosthodontic treatments, particularly with new temporary materials, but data on their color stability and masking ability remains limited. However, data on the color stability and masking ability of these CAD/CAM materials is limited. Telio^® CAD-Temp and VITA CAD-Temp^® blocks were cut into slices and polished. Composite resin specimens were prepared using a custom-designed metal resin former and light-cured. Samples were paired randomly and assigned to experimental groups based on base type and thickness (n = 30). Samples were stored in a controlled environment for 24 h before color evaluation using an EasyShade^® V spectrophotometer. Color difference (ΔE) was calculated using L*, a*, and b* values. Statistical analyses included the Shapiro–Wilk test, Levene’s test, and three-way ANOVA, with post-hoc comparisons using the Bonferroni method (α = 0.05). ΔE was classified according to perceptibility (PT = 1.2) and acceptability (AT = 2.7) values. Full article

Tooth color is a major driver of facial esthetics. While permanent changes in tooth shade can be achieved by bleaching and restorations, there is a need for cosmetic products that can cause reversible color changes. This randomized controlled clinical study assessed the effectiveness and safety of a novel color-correcting product (Hismile™ V34 Color Corrector Serum™) versus a placebo (vehicle control lacking the color-change dyes). A single-center, randomized, controlled, examiner-blind, two-group, parallel design, single-use study design was followed. The test products were applied on a cotton bud for 30 s, and then, rinsed off. Tooth shade for maxillary central incisors was measured at baseline, immediately, and at 30 and 60 min, using the Vita Bleachedguide 3D-Master^® Shade Guide and the EasyShade Advanced 4.0 spectrophotometer (for determining values of L*a*b*). The subjects (N = 60) had a baseline shade of 1M2 (rank 9) or darker. A single application of the test product resulted in an immediate and significant (p < 0.001) three shade improvement (26.2%) according to the shade guide, and the same significant benefits extended to 30 and 60 min. The placebo product did not alter tooth shade (p = 0.326). These changes were accompanied by significant improvements in the L value (whiteness) up to 30 min, and a reduction in b* (yellowness) for up to 60 min. Two-thirds of subjects using the test product stated in a survey that their teeth appeared both whiter and brighter. No safety issues arose from the use of the test product or vehicle control. These results indicate that using a color corrector can achieve worthwhile changes to tooth shade for up to 60 min. Full article

The present study aimed to characterize the microstructure of a temporary 3D printing polymer-based composite material (Resilab Temp), evaluating its optical properties and mechanical behavior according to different post-curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 × 10 × 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on a W3D printer (Wilcos), and light-cured in Anycubic Photon for different lengths of time (no post-curing, 16 min, 32 min, and 60 min). For the structural characterization, analyses were carried out using Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). The mechanical behavior of this polymer-based composite material was determined based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed using a spectrophotometer (VITA Easy Shade Advanced 4.0), which was then evaluated in CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging over two thousand cycles (5–55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1 h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all of the analyses carried out in this study, for the evaluated material, a post-polymerization time of 1 h should be suggested to improve the mechanical performance of 3D-printed devices. Full article

Background: One of the crucial factors influencing the longevity of anterior aesthetic dental restorations is the colour stability of resin composites. Bleaching and whitening have become popular methods for enhancing dental aesthetics. Home whitening techniques, such as special pens, are widely available commercially. This in vitro study aimed to determine the efficiency of a whitening pen in removing tea stains from resin composite by measuring colour differences (ΔE₀₀). Additionally, the study aimed to evaluate the variations in colour parameters measured by extra-oral and intra-oral spectrophotometers. Methods: A total of 45 disc-shaped resin composite specimens were randomly divided into three groups; Group 1: stored in artificial saliva (control), Group 2: stored in artificial saliva followed by a whitening pen application, and Group 3: stored in tea followed by a whitening pen application. Colour measurements were taken three times for each specimen using two spectrophotometers (extra-oral and intra-oral devices); T1: before storage (baseline), T2: after storage in artificial saliva or tea for 6 days; and T3: after one week of whitening pen application in groups 2 and 3. The data were statistically analyzed using one-way ANOVA followed by the Tukey post hoc test (p ≤ 0.05). The independent sample t-test was also employed. The equation of CIEDE2000 (ΔE₀₀) was used to calculate the colour difference between the dry, as-prepared specimens (baseline), and those after storage or bleaching. The colour changes exceeding the acceptability threshold (∆E₀₀ = 1.8) were considered unacceptable. Results: After whitening, the colour of the specimens stored in brewed tea (Group 3) remained unacceptable, as indicated by both the extra-oral and intra-oral spectrophotometers (ΔE₀₀ = 4 and 2.9, respectively). Groups 1 and 2 exhibited lower ΔE₀₀ values than Group 3 (p = 0.01 *). No significant difference was observed between Group 1 (stored in artificial saliva) and Group 2 (stored in artificial saliva and then bleached) (p = 0.3). Significant differences were consistently observed between the data obtained from the extra-oral spectrophotometer and the intra-oral one. Conclusions: The whitening pen proved ineffective in removing tea stains from resin composites. Although significant differences were found between the values obtained by the two spectrophotometers (extra-oral and intra-oral), both devices confirmed the unacceptable colour of the tea-stained resin composites after whitening. Full article

The aim of this in vitro study was to assess the effect of toothpastes, with different compositions, on optical and morphological features of sound and demineralized enamel. We selected twenty-five teeth, recently extracted for orthodontic purposes, for this in vitro study. The teeth were caries free, without stains, fissures, filling or hypoplasia observed at inspection under standard conditions. Teeth were brushed (for 2–3 min, twice a day, for 21 days), with five different toothpastes (four commercially available and an experimental one) containing fluoride and hydroxyapatite. After that, teeth were demineralized with 37% orthophosforic acid (Ultra Etch^®, Ultradent Products Inc., South Jordan, UT, USA) for 60 s. We repeated the brushing protocol for another 21 days on demineralized enamel. Enamel vestibular surfaces were examined using a spectrophotometer (Vita EasyShade -Vita Zahnfabrik, Bad Sackingen, Germany) and a Scanning Electron Microscope (Inspect S^®, FEI Company, Hillsboro, OR, USA). Differences were statistically significant for colour parameters L* and ΔE*. SEM evaluation reveals demineralized enamel mineral gain after brushing with selected toothpastes. Toothpastes with specific ingredients can represent a balance between aesthetic and mineralization, and an oral hygiene correct algorithm is able to preserve enamel characteristics during ortodontic treatement with fixed appliances. Full article

This study investigated the colorimetric properties of different veneering materials on core materials. Standardized specimens (10 mm × 10 mm × 1.5 mm) reflecting four core (polyetheretherketone (PEEK), zirconia (ZrO₂), cobalt–chromium–molybdenum alloy (CoCrMo), and titanium oxide (TiO₂); thickness: 1.5 mm) and veneering materials (VITA Mark II, IPS e.max CAD, LAVA Ultimate and VITA Enamic, all in shade A3; thickness: 0.5, 1.0, 1.5 and 2 mm, respectively) were fabricated. Specimens were superimposed to assemblies, and the color was determined with a spectrophotometer (CieLab-System) or a chair-side color measurement device (VITA EasyShade), respectively. Data were analyzed using three-, two-, and one-way ANOVA, a Chi²-test, and a Wilson approach (p < 0.05). The measurements with EasyShade showed A2 for VITA Mark II, A3.5 for VITA Enamic, B2 for LAVA Ultimate, and B3 for IPS e.max CAD. LabE-values showed significant differences between the tested veneering materials (p < 0.001). CieLab-System and VITA EasyShade parameters of the different assemblies showed a significant impact of core (p < 0.001), veneering material (p < 0.001), and thickness of the veneering material (p < 0.001). PEEK as core material showed comparable outcomes as compared to ZrO₂ and CoCrMo, with respect to CieLab-System parameters for each veneering material. The relative frequency of the measured VITA EasyShade parameters regarding PEEK cores also showed comparable results as compared to the gold standard CoCrMo, regardless of the veneering material used. Full article