Search Results (11)

In this paper, a novel molecularly imprinted polymer membrane modified glassy carbon electrode for electrochemical sensors (MIP-OH-MWCNTs-GCE) for epinephrine (EP) was successfully prepared by a gel-sol method using an optimized functional monomer oligosilsesquioxane-Al₂O₃ sol-ITO composite sol (ITO-POSS-Al₂O₃). Hydroxylated multi-walled carbon nanotubes (OH-MWCNTs) were introduced during the modification of the electrodes, and the electrochemical behavior of EP on the molecularly imprinted electrochemical sensors was probed by the differential pulse velocity (DPV) method. The experimental conditions were optimized. Under the optimized conditions, the response peak current values showed a good linear relationship with the epinephrine concentration in the range of 0.0014–2.12 μM, and the detection limit was 4.656 × 10⁻¹¹ M. The prepared molecularly imprinted electrochemical sensor was successfully applied to the detection of actual samples of horse serum with recoveries of 94.97–101.36% (RSD), which indicated that the constructed molecularly imprinted membrane electrochemical sensor has a high detection accuracy for epinephrine in horse blood, and that it has a better value for practical application. Full article

The use of environmentally friendly and non-toxic biomass-based interfacial solar water evaporators has been widely reported as a method for water purification in recent years. However, the poor stability of the water transport layer made from biomass materials and its susceptibility to deformation when exposed to harsh environments limit its practical application. To address this issue, water-driven recovery aerogel (PCS) was prepared by cross-linking epoxy-based polyhedral oligomeric silsesquioxane (EP-POSS) epoxy groups with chitosan (CS) amino groups. The results demonstrate that PCS exhibits excellent water-driven recovery performance, regaining its original volume within a very short time (1.9 s) after strong compression (ε > 80%). Moreover, PCS has a water absorption rate of 2.67 mm s⁻¹ and exhibits an excellent water absorption capacity of 22.09 g g⁻¹ even after ten cycles of absorption-removal. Furthermore, a photothermal evaporator (PCH) was prepared by loading the top layer with hydrothermally reacted tannins (HAs) and Zn²⁺ complexes. The results indicate that PCH achieves an impressive evaporation rate of 1.89 kg m⁻² h⁻¹ under one sun illumination. Additionally, due to the antimicrobial properties of Zn²⁺, PCH shows inhibitory effects against Staphylococcus aureus and Escherichia coli, thereby extending the application of solar water evaporators to include antimicrobial purification in natural waters. Full article

Phenyl polyhedral oligomeric silsesquioxane (POSS) is modified onto the GO surface by using the strong π–π coupling between a large number of benzene rings at the end of the phenyl POSS structure and the graphite structure in the GO sheet, realizing the non-covalent functionalization of GO (POSS-GO). The POSS-GO-reinforced EP (POSS-GO/EP) composite material is prepared using the casting molding process. The surface morphology of GO before and after modification and its peel dispersion in EP are examined. Furthermore, the mechanical properties, cross-sectional morphology, and reinforcement mechanism of POSS-GO/EP are thoroughly examined. The results show that the cage-like skeleton structure of POSS is embedded between the GO layers, increasing the spacing between the GO layers and leading to a steric hindrance effect, which effectively prevents their stacking and aggregation and improves the dispersion performance of GO. In particular, the 0.4 phr POSS-GO/EP sample shows the best mechanical properties. This is because, on the one hand, POSS-GO is uniformly dispersed in the EP matrix, which can more efficiently induce crack deflection and bifurcation and can also cause certain plastic deformations in the EP matrix. On the other hand, the POSS-GO/EP fracture cross-section with a stepped morphology of interlaced “canine teeth” shape is rougher and more uneven, leading to more complex crack propagation paths and greater energy consumption. Moreover, the mechanical meshing effect between the rough POSS-GO surface and the EP matrix is stronger, which is conducive to the transfer of interfacial stress and the strengthening and toughening effects of POSS-GO. Full article

In this paper, the 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO)-containing diblock copolymer poly[(p-hydroxybenzaldehyde methacrylate)_m-b-(2-((6-oxidodibenzo[c,e][1,2]oxaphosphinin-6-yl)oxy)ethyl methacrylate)_n] (abbrev. poly(HAMA_m-b-HEPOMA_n)) was synthesized by reversible addition fragmentation chain transfer (RAFT) polymerization. When it was continued to react with titanium-hybridized aminopropyl-polyhedral oligomeric silsesquioxane (Ti-POSS) through a Schiff-base reaction, new grafted copolymers poly[(Ti-POSS-HAMA)_m-b-HEPOMA_n] (abbrev. PolyTi) were obtained. Then, they were used as macromolecular flame retardant to modify epoxy resin materials. The thermal, flame retardant and mechanical properties of the prepared EP/PolyTi composites were tested by TGA, DSC, LOI, UL-94, SEM, Raman, DMA, etc. The migration of phosphorus moiety from epoxy resin composites was analyzed by immersing the composites into ethanol/H₂O solution and recording the extraction solution by UV-Vis spectroscopy. The results showed that the added PolyTi enhanced the glass transition temperature, the carbon residue, the graphitization of char, LOI, and mechanical properties of the EP/PolyTi composites when compared to pure cured EP. Furthermore, the phosphorus moieties were more likely to migrate from EP/DOPO composites than that from EP/PolyTi composites. Obviously, compared with small molecular flame retardant modified EP, the macromolecular flame retardant modified EP/PolyTi composites exhibited better thermal stability, flame retardancy, and resistance to migration. Full article

Epoxy resin–polyhedral oligomeric silsesquioxane (EP-POSS) has excellent mechanical properties and hydrophobic properties. In order to adapt for application in sensor and photovoltaic fields, graphene, nano-SiO₂ and nano-ZnO were used to modify EP-POSS. FTIR was used to characterize changes on the surface structure after introducing nanoparticles. The change of hydrophobicity was measured using a contact angle test. TEM test results showed that nanoparticles were successfully inserted between the graphene sheets. However, the content of Si on the surface was low, as the cage structure of POSS in the molecular chain was coated by epoxy groups. XRD tests indicated that nanoparticles facilitated the dispersion of graphene in EP-POSS. XPS characterized the chemical state and content of the elements, confirming that the addition of graphene can induce the enrichment of Si on the surface of EP-POSS, which had a shielding effect on the main chain and improved the hydrophobicity. Wear resistance and adhesion tests showed that, after the introduction of nanoparticles, the EP-POSS coating film met the requirements of graphene materials. Full article

A new polyhedral oligomeric silsesquioxane (POSS) designed with eight –(CH₂)₃–NH–(CH₂)₂–NH₂ groups (PNEN) at its apexes was used as nanocomposite uploading into 1,2-bis(triethoxysilyl)ethane (BTESE)-derived organosilica to prepare mixed matrix membranes (MMMs) for gas separation. The mixtures of BTESE-PNEN were uniform with particle size of around 31 nm, which is larger than that of pure BTESE sols. The characterization of thermogravimetric (TG) and gas permeance indicates good thermal stability. A similar amine-contained material of 3-aminopropyltriethoxysilane (APTES) was doped into BTESE to prepare hybrid membranes through a copolymerized strategy as comparison. The pore size of the BTESE-PNEN membrane evaluated through a modified gas-translation model was larger than that of the BTESE-APTES hybrid membrane at the same concentration of additions, which resulted in different separation performance. The low values of E_p(CO₂)-E_p(N₂) and E_p(N₂) for the BTESE-PNEN membrane at a low concentration of PNEN were close to those of copolymerized BTESE-APTES-related hybrid membranes, which illustrates a potential CO₂ separation performance by using a mixed matrix membrane strategy with multiple amine POSS as particles. Full article

Hydrophobic films are widely used in aerospace, military weapons, high-rise building exterior glass, and non-destructive pipeline transportation due to their antifouling and self-cleaning properties. This paper details the successful preparation of hydrophobic epoxy caged sesquioxane (EP-POSS) via two steps of simple organic synthesis, along with studies on the effects of viscosity and reaction time on the reaction. Interestingly, the EP-POSS presented a large contact angle of 125°, indicating its excellent hydrophobicity. The surface micromorphology was observed via FE-SEM (field emission scanning electron microscopy), transmission electron microscopy (TEM), and atomic force microscopy (AFM), and the structural composition and elemental contents were analyzed via X-ray photoelectron spectroscopy (XPS) and energy-dispersive spectrometry (EDS). Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) tests showed that EP-POSS had excellent thermal properties, and the first degradation reaction occurred at 354 °C. The mechanical performance and abrasion resistance results demonstrated that EP-POSS could be used in solar panels. Full article

A novel organic-inorganic hybrid containing allyl benzoxazine and polyhedral oligomeric silsesquioxane (POSS) was synthesized by the thiol-ene (click) reaction. The benzoxazine (BOZ)-containing POSS (SPOSS-BOZ) copolymerized with benzoxazine/epoxy resin was used to prepare composites of SPOSS-PBZ-E nanocomposites(NPs). The polymerization behavior was monitored by FTIR and non-isothermal differential scanning calorimetry (DSC), which showed that the composites had completely cured with multiple polymerization mechanisms according to the oxazine ring-opening and epoxy resin (EP) polymerization. The thermal properties of the organic–inorganic polybenzoxazine (PBZ) nanocomposites were analyzed by DSC and thermogravimetric analysis (TGA). Furthermore, the X-ray diffraction analysis and the scanning electron microscopy (SEM) micrographs of the SPOSS-PBZ-E nanocomposites indicated that SPOSS was chemically incorporated into the hybrid nanocomposites in the size range of 80–200 nm. The flame retardancy of the benzoxazine epoxy resin composites was investigated by limiting oxygen index (LOI), UL 94 vertical burn test, and cone calorimeter tests. When the amount of SPOSS reached 10% or more, the vertical burning rating of the curing system arrived at V-1, and when the SPOSS-BOZ content reached 20 wt %, the thermal stability and flame retardancy of the material were both improved. Moreover, in the cone calorimeter testing, the addition of SPOSS-BOZ hindered the decomposition of the composites and led to a reduction in the peak heat release rate (pHRR), the average heat release rate (aHRR), and the total heat release (THR) values by about 20%, 25%, and 25%, respectively. The morphologies of the chars were also studied by SEM and energy dispersive X-ray spectroscopy (EDX), and the flame-retardant mechanism of POSS was mainly a condensed-phase flame retardant. The ceramic layer was formed by the enrichment of silicon on the char surface. When there are enough POSS nanoparticles, it can effectively protect the combustion of internal polymers. Full article

The outstanding diffusivity and permeability of supercritical carbon dioxide (scCO₂) are extremely beneficial for grafting reaction. In this work, aramid fibers (AF) are modified in scCO₂ by glycidyl-polyhedral oliomeric silsesquioxane (POSS) with 2-ethyl-4-methylimidazole (2E4MZ) on the basis of cleaning with acetone. The surface morphology and chemical structure of the modified AF were measured and characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Scanning electron microscope (SEM), Thermogravimetric (TG), and Atomic force microscope (AFM). The interfacial shear strength (IFSS) was measured by a micro-bond pull-out test, then the modified AF/EP composites were prepared and the interlaminar shear strength (ILSS) was characterized. Research has shown that some of the glycidyl-POSS molecular chains permeated into the surface of the fiber and grafted onto the surface of the AF after modification, and the other glycidyl-POSS self-assembled on the surface of the fiber. XPS indicated the introduction of C–O and –COO–, which confirmed the existence of chemical reactions between AF and glycidyl-POSS. AFM and SEM images revealed that 2E4MZ, not only promoted the grafting reaction of glycidyl-POSS, but also intensified the self-assembly of glycidyl-POSS, both of which increased the roughness of the fiber. A monofilament tensile test and micro-bond pull-out test showed that there was a negative effect on the tensile strength after scCO₂ processing. The tensile strength of modified AF, with glycidyl-POSS, increased the highest strength of 25.7 cN dtex⁻¹, which was 8% higher than that of pristine AF. The improvement of ILS roughness and the polar chemical groups produced in grafting reaction. These results indicated that AF, treated in scCO₂, with glycidyl-POSS, which is a suitable way of fiber modification, can significantly improve the surface adhesion of AF reinforced composites. Full article

Phthalonitrile–polyhedral oligomeric silsesquioxane (POSS) copolymers were prepared by adding two different POSS cage mixtures: epoxycyclohexyl POSS (EP0408) and N-phenylaminopropyl POSS (AM0281). The cure behavior and properties of these polymers were analyzed and compared using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), Fourier transform far infrared (FTIR) measurements, and rheometric studies. The POSS-containing polymers showed higher chemical reactivity, better thermal stability and better mechanical performance in comparison to their unmodified counterparts. All the polymers showed water absorption below 1.5%. As revealed by FTIR measurements, the polymerization products contained triazine ring structures that were responsible for the superior thermal properties exhibited by these POSS-containing polymers. Full article

A study was carried out involving the filling of epoxy resin (EP) with bentonites and silica modified with polyhedral oligomeric silsesquioxane (POSS). The method of homogenization and the type of filler affect the functional and canceling properties of the composites was determined. The filler content ranged from 1.5% to 4.5% by mass. The basic mechanical properties of the hybrid composites were found to improve, and, in particular, there was an increase in tensile strength by 44%, and in Charpy impact strength by 93%. The developed hybrid composites had characteristics typical of polymer nanocomposites modified by clays, with a fine plate morphology of brittle fractures observed by SEM, absence of a plate separation peak in Wide Angles X-ray Scattering (WAXS) curves, and an exfoliated structure observed by TEM. Full article