Search Results (4)

Insulating cotton was used to change the airflow temperature in the exhaust pipe of a diesel engine, and soot particles at different positions in the exhaust pipe under different operating conditions were collected. The morphologies and microstructures of soot particles were observed by high-resolution transmission electron microscopy (HRTEM). The characteristic parameters, including the mean primary particle diameter (d_p), radius of gyration of soot aggregate (R_g), fractal dimension of soot particle (D_f), carbon layer spacing (D_s), and carbon layer torsion resistance (T_f), were statistically analyzed. The changes in each characteristic parameter before and after adding insulating cotton were compared. After installing the cotton, soot particles still grew through surface chemical reactions and physical processes in the diesel exhaust pipe, the agglomeration becomes more and more prevalent, the particle size increased, and D_f increased. The increase in the airflow temperature in the exhaust pipe promoted the surface growth of primary soot particles and enhanced the turbulence, which made the chain-like soot particles more likely to reunite under the action of turbulent eddies. Consequently, R_g decreased and D_f increased. Furthermore, the average D_s and T_f of primary soot particles deceased, especially under high loads. This indicated that the increase in the temperature of the exhaust pipe was conducive to the graphitization of primary soot particles. Full article

In engineering applications, dust deposition on the heat transfer channel greatly reduces the efficiency of heat transfer. Therefore, it is very significant to study the characteristics of particle deposition for thermal energy engineering applications. In this study, the Reynolds stress model (RSM) and the discrete phrase model (DPM) were used to simulate particle deposition in a 3D convex-dimpled rough channel. A discrete random walk model (DRW) was used for the turbulent diffusion of particles, and user-defined functions were developed for collisions between particles and walls. An improved deposition model of rebound between particles was developed. The flow structure, secondary flow, temperature distribution, Q criterion, and particle deposition distribution in the convex-dimpled rough channel were analyzed after a study of the grid independence and a numerical validation. The results showed that these mechanisms affected the flow structure in the flow field. For tiny particles (dp ≤ 10 μm), the presence of convex dimples promoted their deposition. The rates of particle deposition in the presence of convex dimples were 535, 768, 269, and 2 times higher than in smooth channels (particle sizes of 1, 3, 5, and 10 μm, respectively). However, for large particles (dp > 10 μm), although the presence of convex dimples had a certain effect on the location distribution of particle deposition, it had little effect on the deposition rates of large particles, which were 0.99, 0.98, 0.97 and 0.96 times those in the smooth channel, respectively. Full article

This study investigates the enhancement of dairy wastewater treatment using chemical and physical pre-treatments coupled with membrane separation techniques to reduce membrane fouling. Two mathematical models, namely the Hermia and resistance-in-series module, were utilized to comprehend the mechanisms of ultrafiltration (UF) membrane fouling. The predominant fouling mechanism was identified by fitting experimental data into four models. The study calculated and compared permeate flux, membrane rejection, and membrane reversible and irreversible resistance values. The gas formation was also evaluated as a post-treatment. The results showed that the pre-treatments improved UF efficiency for flux, retention, and resistance values compared to the control. Chemical pre-treatment was identified as the most effective approach to improve filtration efficiency. Physical treatments after microfiltration (MF) and UF showed better fluxes, retention, and resistance results than ultrasonic pre-treatment followed by UF. The efficacy of a three-dimensionally printed (3DP) turbulence promoter was also examined to mitigate membrane fouling. The integration of the 3DP turbulence promoter enhanced hydrodynamic conditions and increased the shear rate on the membrane surface, shortening filtration time and increasing permeate flux values. This study provides valuable insights into optimizing dairy wastewater treatment and membrane separation techniques, which can have significant implications for sustainable water resource management. The present outcomes clearly recommend the application of hybrid pre-, main- and post-treatments coupled with module-integrated turbulence promoters in dairy wastewater ultrafiltration membrane modules to increase membrane separation efficiencies. Full article

Designing turbulence promoters with optimal geometry and using them for ultrafiltration systems has been a key challenge in mitigating membrane fouling. In this study, six different turbulence promoters were created using three-dimensional printing technology and applied in dead-end ultrafiltration. Three-dimensional-printed (3DP) turbulence promoter configurations were integrated into a classical batch ultrafiltration cell. The effects of these configurations and the stirring speeds on the permeate filtration flux, organic rejections, and membrane resistances were investigated. The fouling control efficiency of the 3DP promoters was evaluated using two polyethersulfone membranes in a stirred ultrafiltration cell with model dairy wastewater. The Hermia and resistance-in-series models were studied to further investigate the membrane fouling mechanism. Of the Hermia models, the cake layer model best described the fouling in this membrane filtration system. It can be concluded that the 3DP turbulence promoters, combined with intense mechanical stirring, show great promise in terms of permeate flux enhancement and membrane fouling mitigation. Using a well-designed 3DP turbulence promoter improves the hydrodynamic flow conditions on the surface of the stirred membrane separation cells based on computational fluid dynamics modeling. Therefore, the factors effecting the fabrication of 3DP turbulence promoters are important, and further research should be devoted to revealing them. Full article